igt@kms_rotation_crc@multiplane-rotation-cropping-top on shard-lnl@xe-4270-84b93f7cc4ceb1c0bee1e478b652db7bbc40c7bb Test details

Detail	Value
Duration	10.77 seconds
Hostname	shard-lnl-5
Igt-Version	IGT-Version: 2.3-gf38f4d8e9 (x86_64) (Linux: 6.19.0-rc1-lgci-xe-xe-4270-84b93f7cc4ceb1c0b+ x86_64)
Out	Using IGT_SRANDOM=1766194556 for randomisation Opened device: /dev/dri/card0 Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.772s)
Err	Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.772s)
Dmesg	<6> [76.684230] Console: switching to colour dummy device 80x25 <6> [76.684291] [IGT] kms_rotation_crc: executing <7> [76.689734] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [76.689745] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [76.689916] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [76.690028] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [76.690303] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [76.690306] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [76.690445] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [76.690550] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [76.690877] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [76.690882] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [76.691023] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [76.691127] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <7> [76.691468] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] <7> [76.691472] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1] <7> [76.691945] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [76.692266] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [76.692381] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [76.692492] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [76.692626] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [76.692631] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [76.692634] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [76.692635] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7> [76.692637] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [76.692640] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [76.692641] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor <5> [76.692644] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [76.692645] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0 <5> [76.692647] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [76.692660] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes <7> [76.692807] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [76.693108] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [76.693936] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [76.693943] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [76.693945] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [76.694007] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes: <7> [76.694010] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [76.694015] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [76.694029] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [76.694033] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [76.694196] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [76.694207] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [76.694210] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [76.694351] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [76.694362] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [76.694365] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [76.694507] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <6> [76.694668] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top <7> [76.696534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0 <7> [76.696638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [76.696726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [76.696803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [76.696875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [76.696970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [76.697076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [76.697176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [76.697274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [76.697371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [76.697467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [76.697829] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [76.697944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [76.698081] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [76.732227] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [76.733104] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [76.733906] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [76.734369] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [76.734788] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [76.735210] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation <7> [76.735528] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [76.735963] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [76.736437] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [76.736846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [76.737201] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [76.737541] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [76.737911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [76.738241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [76.738540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [76.738869] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [76.739202] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [76.739494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [76.739781] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [76.740037] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [76.740291] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [76.740544] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [76.740806] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8 <7> [76.741046] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [76.741271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [76.741535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [76.741920] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [76.742123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [76.742322] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [76.742508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [76.742692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [76.742911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [76.743086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [76.743272] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [76.743471] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [76.743640] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [76.743921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [76.744079] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [76.744229] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [76.744378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [76.744545] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [76.744689] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [76.744858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [76.744993] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [76.745128] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [76.745260] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [76.745387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [76.745513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [76.745637] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [76.745775] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [76.745896] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [76.746015] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [76.746149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [76.746269] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [76.746387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [76.746503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.746616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.746733] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.746862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [76.746987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [76.747100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.747214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.747326] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [76.747425] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [76.747522] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [76.764608] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [76.764806] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [76.767252] xe 0000:00:02.0: [drm:intel_dp_dump_link_status [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] ln0_1:0x77 ln2_3:0x77 align:0x80 sink:0x1 adj_req0_1:0x0 adj_req2_3:0x0 <7> [76.767474] xe 0000:00:02.0: [drm:intel_dp_link_ok [xe]] [ENCODER:390:DDI A/PHY A] 8b/10b link not ok, retraining <7> [76.784792] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [76.785293] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [76.785669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [76.818210] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427] <7> [76.819461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [76.819888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [76.820197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.820486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.820816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.821123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.821408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.821664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.821991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.822240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.822564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [76.823209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [76.823463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [76.823723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.823963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.824223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.824460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.824690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.825014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.825273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.825508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.825785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [76.826359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [76.826580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [76.826880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.827091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.827290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.827476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.827660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.827906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.828080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.828248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.828424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [76.828723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [76.829005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [76.829268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [76.829563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [76.830122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [76.831105] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [76.831340] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [76.832013] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [76.832200] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [76.847724] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1 <7> [76.850674] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430] <7> [76.881832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [76.882389] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [76.882942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [76.883765] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431] <7> [76.884564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [76.885021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [76.885328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.885681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [76.886098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [76.886437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [76.886821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [76.887279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [76.887761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [76.888221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [76.888665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [76.889193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [76.889671] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz <7> [76.890583] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [76.890986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [76.915770] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [76.916297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [76.916700] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432] <7> [76.916782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [76.917478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [76.917916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [76.918244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.918533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [76.918870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [76.919151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [76.919456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [76.919890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [76.920281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [76.920666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [76.921108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [76.921505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [76.923028] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [76.923401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [76.948745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [76.948940] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433] <7> [76.949096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [76.949394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [76.949644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [76.949951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [76.950173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [76.950381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [76.950583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [76.950849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [76.951087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [76.951375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [76.951641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [76.951952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [76.952278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [76.952551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [76.953916] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [76.954214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [76.981849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [76.982333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [76.982822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [76.983547] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434] <7> [77.005486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [77.005887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [77.006206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.006490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.006980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.007231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.007566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.007938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.008251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.008567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.009050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.009314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.010059] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.010312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.031695] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435] <7> [77.031780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.032235] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.032675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.057606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [77.057757] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [77.057853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.057936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.058016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.058083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.058160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.058255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.058345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.058430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.058514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.058594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.059050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.059150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.081756] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436] <7> [77.082450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [77.082828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [77.082963] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.083085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.083362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.083376] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.083592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.083766] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.083876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.084183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.084548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.084938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.085267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.085584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.085916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.086659] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.086988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.099221] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437] <7> [77.131833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.132434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.132725] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438] <7> [77.132939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.134153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [77.134504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [77.134876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.135180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.135473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.135863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.136188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.136602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.137049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.137499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.137982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.138388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.139357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.139803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.164868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.165404] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.165896] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.166115] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439] <7> [77.166900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [77.167255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [77.167567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.167917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.168199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.168483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.168817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.169219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.169610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.170099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.170527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.170978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.171993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.172394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.198882] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440] <7> [77.198850] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.199344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.199648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [77.199809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.200070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [77.200382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.200678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.201036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.201367] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.201688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.202165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.202557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.202981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.203387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.203772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.205125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.205524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.231861] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.232309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.232682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.232988] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441] <7> [77.250249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [77.250580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [77.250946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.251234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.251516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.252038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.252387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.252872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.253298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.253685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.254137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.254513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.255685] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.256149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.282302] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442] <7> [77.282815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.283396] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.283903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.306632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [77.306881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [77.306998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.307106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.307207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.307303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.307416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.307576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.307739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.307865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.307984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.308102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.308545] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.308673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.331394] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [77.331781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [77.331891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.332088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.332378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.332381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.332675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.332846] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.333023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.333285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.333538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.333880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.334105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.334541] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [77.334796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [77.335000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.335196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.335394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.335586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.335811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.335985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.336162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.336334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.336967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.337242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.381457] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.382001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.381935] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.382347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.382477] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.382664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.383059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.383019] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.383394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.383780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.384420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.384743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.385025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.385272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.385518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.385868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.386157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.386542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.386965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.387371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.387761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.388189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.389147] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.389550] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.415139] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443] <7> [77.414923] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.415415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.415882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.416142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [77.416484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [77.416844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.417135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.417415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.417762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.418071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.418643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [77.418991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [77.419226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.419507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.419751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.419981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.420207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.420671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [77.420964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [77.421151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.421344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.421522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.421695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.421936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.422209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.422464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.422786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.423019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.423250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.423903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.424125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.447975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.448254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.448488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.448761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.448879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.448999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.449258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.449292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.449514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.449649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.450053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.450301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.450536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.450850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.451082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.451350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.451567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.452047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.452247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.452473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.452671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.452951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.453124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.453299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.453568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.453863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.454114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.454369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.454593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.455340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.455570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.481611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [77.482012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [77.482159] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.482293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.482553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.482607] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.482873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.483096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.483177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.483515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.483932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.484297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.484648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.485040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.485389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.486403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.486807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.514664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [77.515108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [77.515214] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.515413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.515697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.515703] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.516139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.516207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.516429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.516755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.517161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.517552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.518043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.518479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.518953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.520174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.520574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.547989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [77.548286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [77.548542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.548852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.548993] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.549104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.549363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.549437] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.549636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.549860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.550042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.550405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.550773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.551186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.551558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.552463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.552847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.581258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.581578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.581926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.582043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.582188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.582441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.582487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.582762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.582930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.583065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.583433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.583812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.584163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.584555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.585001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.585881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.586246] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.614663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [77.615056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [77.615173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.615336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.615620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.615618] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.615954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.616103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.616228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.616553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.616998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.617389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.617797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.618229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.618649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.619946] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.620349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.647908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [77.648184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [77.648415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.648632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.648923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.649058] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.649148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.649444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.649463] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.649842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.649880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.650199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.650545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.650933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.651326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.652434] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.652804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.681507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [77.681868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [77.681898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.682124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.682362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.682318] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.682591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.682672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.682915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.683197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.683564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.683988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.684391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.684767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.685104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.686065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.686430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.711812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.712231] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.712582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.713045] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [77.713029] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [77.713030] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [77.714612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [77.714993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [77.715256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.715504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.715778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.716041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.716343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [77.716762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [77.717121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [77.717470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.717880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [77.718221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [77.719292] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.719654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.748829] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444] <7> [77.748768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.749261] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.749651] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.750400] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.750812] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [77.751112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [77.751378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [77.751632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.751947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.752250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.752492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.752836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.753079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [77.753308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [77.753535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [77.753794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.754014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.754233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.754448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.754702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.755169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [77.755551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [77.755943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.756337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.756675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [77.757830] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.758162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.764198] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [77.783196] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445] <7> [77.784885] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.814529] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.814950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [77.815037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.815314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [77.815528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.815604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [77.815954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.816006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.816295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.816570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.816924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.817227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [77.817625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [77.818090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [77.818528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.818963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.819353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [77.820366] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.820794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.848041] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.848435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [77.848803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [77.848832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.849077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [77.849278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.849334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.849608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.849661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.849899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.850185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.850458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.850831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [77.851183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [77.851583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.851961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.852319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [77.853576] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.853987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.881162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.881500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [77.881831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [77.881829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.882077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [77.882241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.882307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.882530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.882592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.882797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.883034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.883350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [77.883911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.884225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [77.884475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [77.884734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [77.884951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.885165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.885381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.885589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.885858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [77.886215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [77.886623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [77.887053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.887424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.887803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [77.888897] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.889260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.914863] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.914867] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.915188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [77.915248] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.915428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [77.915578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.915660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [77.915958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.916234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.916468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.916758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.917045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.917573] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.917938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [77.918196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [77.918440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [77.918682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.918999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.919238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.919473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.919697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.920154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [77.920495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [77.920829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.921141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.921425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [77.922227] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.922520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.948103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.948577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [77.949037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [77.949178] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.949358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [77.949665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.949763] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.950053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.950234] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.950349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.950636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.951051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [77.951682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.952076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [77.952329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [77.952573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [77.952855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.953075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.953294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.953544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.953823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [77.954149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [77.954455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [77.954822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.955109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [77.955374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [77.956136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.956406] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.981168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.981493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [77.981862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [77.981997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.982108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [77.982339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.982408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.982593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.982861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.982802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.983094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.983391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.984094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [77.984408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [77.984660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [77.984983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [77.985228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.985494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.985733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.985959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.986179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [77.986498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [77.986905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [77.987221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.987515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [77.987830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [77.988555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.988852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.997989] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.031129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.031484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.031827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.031952] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.032070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.032304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.032364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.032546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.032756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.032820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.033073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.033411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.033799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.034187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.034572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.035053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.035449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.036438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.036864] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.064544] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.064945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [78.064991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.065204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [78.065442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [78.065400] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.065668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.065795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.066055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.066299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.066583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.066922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.067283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.067635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.068044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.068385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.068746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.070014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.070375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.097902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.098289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.098620] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.098976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.099132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.099255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.099522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.099621] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.099811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.100072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.100078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.100377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.100771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.101126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.101473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.101871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.102210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.103285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.103642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.131372] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.131772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [78.131892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.132076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [78.132336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [78.132334] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.132586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.132765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.132926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.133169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.133442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.133724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.134087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.134441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.134805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.135200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.135562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.136544] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.136943] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.164465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.164866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [78.164957] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.165174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [78.165409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [78.165369] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.165635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.165776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.166013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.166259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.166519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.166824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.167190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.167543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.167927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.168323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.168696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.169778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.170133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.198761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.199365] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446] <7> [78.199210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.199591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.201806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.202187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [78.202471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [78.202775] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [78.203036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.203331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.203579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.203876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.204139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.204374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.204605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.204885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.205164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.205414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.205640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.205920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.206161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.206495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.206848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.207229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.207543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.207987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.208971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.209283] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.215624] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447] <7> [78.216558] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.247780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.248121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [78.248382] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [78.248626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [78.248963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.248984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.249232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.249427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.249482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.249811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.249844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.250093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.250459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.250854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.251211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.251560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.251949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.252916] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.253303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.281129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.281392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [78.281560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [78.281747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [78.281761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.281893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.282030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.282005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.282162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.282211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.282309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.282457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.282635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.282843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.283107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.283363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.283614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.284428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.284613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.314435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.314730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [78.314882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [78.315020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [78.315153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.315281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.315407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.315550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.315735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.315762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.315969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.315993] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.316167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.316222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.316358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.316546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.316737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.317792] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.318133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.348090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.348451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [78.348772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [78.348794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.349035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [78.349203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.349291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.349503] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.349542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.349850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.350093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.350415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.350795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.351112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.351423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.351738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.352077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.352929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.353211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.381229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.381792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [78.381893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.382115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [78.382406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [78.382391] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.382681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.382862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.383027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.383290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.383587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.383939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.384507] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.384862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [78.385114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [78.385356] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [78.385592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.385896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.386192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.386439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.386681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.387125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.387508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.387961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.388331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.388729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.389714] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.390030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.414577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.415064] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [78.415035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.415376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [78.415482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.415664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [78.415939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.416052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.416402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.416711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.416967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.417257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.417881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.418257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [78.418585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [78.419000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [78.419248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.419483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.419718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.419931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.420160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.420500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.420844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.421160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.421504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.421852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.422637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.422956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.431142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.464410] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.464822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [78.464911] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.465181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [78.465470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [78.465405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.465804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.465875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.466105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.466350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.466599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.466924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.467549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.467876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [78.468127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [78.468354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [78.468578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.468875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.469136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.469363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.469603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.470000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.470378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.470733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.471074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.471408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.472304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.472662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.497911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.498301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [78.498587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [78.498924] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [78.499053] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.499183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.499428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.499498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.499670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.499942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.500023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.500289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.500898] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.501188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [78.501416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [78.501636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [78.501925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.502176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.502393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.502604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.502884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.503262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.503573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.503893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.504228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.504501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.505480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.505749] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.531087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.531424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [78.531670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [78.531993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [78.532023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.532224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.532372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.532447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.532737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.532708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.532987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.533278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.533638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.534108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.534458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.534783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.535093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.535949] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.536240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.564621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.565039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [78.565095] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.565349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [78.565507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.565588] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [78.565885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.565922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.566132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.566399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.566666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.567074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [78.567438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.567816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.568164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.568562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.568992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.569985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.570347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.597760] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.598149] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [78.598426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [78.598722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [78.598883] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.599000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.599263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.599371] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.599525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.599866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.599827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.600131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [78.600491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [78.600910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [78.601346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.601739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [78.602106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [78.603084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.603447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.631174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [78.631500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [78.631855] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [78.631995] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.632141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.632412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.632483] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.632701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.632942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.632996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.633258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [78.633484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [78.633738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [78.633961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [78.634183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.634403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.634624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.634930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.635178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.635530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.635977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.636334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.636672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.637123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.638198] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.638592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.639510] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [78.639836] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [78.664506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.664869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.664878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.665124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.665227] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.665359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.665541] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.665586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.665909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.666168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.666488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.666864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.667189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.667504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.667865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.668647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.669018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.698767] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448] <7> [78.698840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.699296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.699732] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [78.699722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.700019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [78.700289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.700603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.701011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.701265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.701551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.701988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.702395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.702785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.703194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.703552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.704629] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.705077] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.731124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.731476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.731853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.731953] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.732138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.732411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.732438] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.732758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.732903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.733032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.733392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.733768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.734174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.734514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.734942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.735957] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.736318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.764788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [78.764849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.765138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [78.765334] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.765443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.765767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.765789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.766045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.766366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.766699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.767103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.767499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.767932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.768363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.768762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.769878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.770273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.797752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [78.798048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [78.798300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.798538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.798868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.798978] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.799134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.799405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.799426] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.799788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.799852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.800148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.800498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.800937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.801329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.802327] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.802700] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.831055] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [78.831327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [78.831559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.831847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.831971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.832080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.832311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.832384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.832559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.832778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.832963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.833321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.833694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.834090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.834429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.835284] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.835644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.864824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.865254] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.865622] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.867774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.868070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.868321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.868556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.868902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.869134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.869467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.869865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.870210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.870583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.870952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.871284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.872213] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.872556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.897859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [78.898194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [78.898468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.898800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.898945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.899060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.899331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.899393] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.899607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.899819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.900200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [78.900465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [78.900723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.900952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.901222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.901449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.901710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.902063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.902411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.902837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.903228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.903592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.904591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.904998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.931183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.931502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.931867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.931984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.932154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.932430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.932477] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.932793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.932955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.933115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.933707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.933948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.934179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.934452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.934703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.934998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.935248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.935633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.936078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.936437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.936801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.937166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.938104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.938390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.964612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [78.965039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [78.965098] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.965316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.965555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.965511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.965857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.965932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.966125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.966441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.967000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [78.967242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [78.967473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.967727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.967957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.968195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.968432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.968965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [78.969190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [78.969453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.969703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.969952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.970164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.970385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.970757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.971113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.971454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.971789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.972092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.972965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.973258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.997706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [78.997977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [78.998208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.998426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.998637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.999008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.999082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.999235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.999436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.999643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [78.999771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.999907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.000104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.000296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.000486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.000746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.000956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.001426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [79.001674] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.001884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.002104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.002283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.002461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.002718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.003021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.003306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.003574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.003864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.004106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.004846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.005086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.031124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [79.031444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [79.031807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.031887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.032203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.032294] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.032483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.032744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.032834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.033097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.033353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.033601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.033930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.034809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.035140] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.081324] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.081793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.081921] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.082096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.082374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.082420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.082643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.082915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.083031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.083375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.083830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.084221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.084597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.085106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.085489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.086591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.087038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.114716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.115256] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.115746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.116699] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449] <7> [79.117599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [79.118015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [79.118324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.118697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.118985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.119304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.119614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.120182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.120617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.121098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.121481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.121877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.122913] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.123311] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.147755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.148143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.148444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.148790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.148877] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.149045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.149337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.149321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.149631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.149752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.150100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.150491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.150972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.151349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.151736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.152736] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.153099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.181352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [79.181645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [79.182033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.182063] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.182295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.182547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.182536] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.182926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.183004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.183241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.183670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.184066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.184452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.184920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.185303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.186325] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.186747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.214351] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [79.214750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [79.214894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.215053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.215337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.215380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.215612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.215872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.216002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.216345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.216827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.217277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.217747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.218128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.218547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.219634] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.220091] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.247830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [79.248178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [79.248483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.248834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.248870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.249119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.249360] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.249446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.249822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.249823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.250228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.250621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.251126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.251505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.251915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.252905] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.253313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.281018] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.281272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.281457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.281622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.281857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.281875] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.282011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.282162] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.282202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.282404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.282416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.282623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.282917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.283238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.283551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.284534] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.284920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.314173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [79.314303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [79.314360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.314418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.314475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.314536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.314615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.314729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.314818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.314882] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.314915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.315017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.315040] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.315118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.315165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.315546] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.315683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.347406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.347487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.347544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.347601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.347670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.347727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.347807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.347928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.348034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.348134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.348219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.348303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.348671] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.348852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.348975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.349106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.349191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.376017] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off <7> [79.376133] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [79.380862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [79.380947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [79.381004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.381059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.381114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.381169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.381240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.381329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.381414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.381492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.381570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.381667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.381680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.381852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.381979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.382094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.382409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.414102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [79.414218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [79.414304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.414384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.414456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.414519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.414598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.414746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.414755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.414871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.414932] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.414979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.415054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.415085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.415189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.415581] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.415709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.447666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.447849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.447972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.461530] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450] <7> [79.462263] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.462417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [79.462507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [79.462590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [79.462696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.462775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.462853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.462929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.463010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.463093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [79.463177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [79.463252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [79.463323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.463393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.463462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.463531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.463617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.463822] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.463921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [79.463995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [79.464062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [79.464127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.464193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.464259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.464324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.464390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.464455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [79.464518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [79.464582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [79.464653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.464724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.464786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.464847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.464913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.465019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.465126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.465230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.465337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.465441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.466032] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.466149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.480571] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [79.498626] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451] <7> [79.499233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.530786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.530925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.530999] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.531066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.531131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.531193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.531255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.531315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.531390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.531526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.531652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.531664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.531739] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.531822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.531844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.531896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.531967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.531972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.532039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.532114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.532188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.532297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.532404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.532497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.532583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.532701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.533283] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.533531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.564232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.564420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [79.564506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [79.564579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [79.564672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.564662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.564744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.564794] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.564817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.564894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.564917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.565009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.565277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.565384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [79.565460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [79.565535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [79.565604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.565684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.565761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.565830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.565904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.566024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.566135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.566245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.566358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.566473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.567090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.567229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.597565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.597806] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.597846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.597950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.597978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.598047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.598140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.598126] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.598233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.598329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.598424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.598546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.598880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.599020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.599124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.599224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.599323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.599422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.599525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.599664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.599785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.599964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.600139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.600316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.600495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.600770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.601656] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.601878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.631201] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.631478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [79.631715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [79.631714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.631889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [79.631986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.632053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.632218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.632236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.632383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.632545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.632764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.633048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.633320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.633588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.633859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.634108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.634985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.635265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.664187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.664459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [79.664708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [79.664688] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.664894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [79.664969] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.665072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.665250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.665227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.665428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.665601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.665819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.666101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.666374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.666663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.666932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.667201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.668131] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.668422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.697673] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.697856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.698044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.698276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [79.698348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.698544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [79.698790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [79.699008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.699224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.699437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.699680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.699951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.700326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.700704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.701023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.701337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.701668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.703215] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.703563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.714712] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.747725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.747666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.748071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.748066] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.748296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.748384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.748499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.748720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.748919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.749114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.749308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.749554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.749922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.750250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.750561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.750864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.751153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.752214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.752516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.781044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.781422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [79.781704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [79.781707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.781920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [79.782022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.782124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.782318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.782306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.782510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.782719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.782934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.783249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.783550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.783866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.784162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.784455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.785560] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.785898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.814211] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.814506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [79.814761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [79.814757] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.814969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [79.815064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.815163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.815354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.815343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.815547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.815769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.815986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.816291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.816585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.816893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.817182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.817467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.818459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.818785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.847650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.847956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.847989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.848274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [79.848289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.848506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [79.848740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [79.848952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.849163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.849369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.849575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.849837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [79.850168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [79.850488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [79.850895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.851207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [79.851516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [79.852551] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.852900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.880883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.881200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [79.881410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [79.881598] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [79.881829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.881833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.882018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.882105] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.882196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.882373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.882355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.882583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [79.882911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [79.883208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.883496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.883814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.884102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.885125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.885432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.914661] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.914963] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.915218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.919576] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452] <7> [79.922087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.922476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [79.922724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [79.922920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [79.923102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.923280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.923458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.923655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.923839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.924014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.924189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.924357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.924518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.924695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.924859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.925018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.925222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.925490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.925750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.925988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.926212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.926435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.927570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.927802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.933215] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453] <7> [79.934642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.964337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.964747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.964799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.965053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.965092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.965282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.965404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.965500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.965742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.965962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.966181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.966451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.967027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.967308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.967525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.967816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.968028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.968236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.968444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.968680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.968905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.969261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.969635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.969955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.970269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.970582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.971533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.971879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.997650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.997840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.997966] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.998129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [79.998193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.998315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [79.998479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [79.998877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.999045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.999203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.999357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.999673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.000090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.000286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [80.000434] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [80.000577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [80.000740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.000886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.001023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.001157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.001297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.001514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.001745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.001949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.002144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.002330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.003194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.003392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.031000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.031314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.031526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.031767] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.031772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.031966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.032065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.032161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.032354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.032339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.032544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.032791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.033279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.033534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.033757] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.033948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.034136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.034322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.034510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.034715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.034919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.035243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.035560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.035885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.036189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.036483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.037528] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.037865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.064449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.064745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.064814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [80.065012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [80.065032] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.065196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [80.065290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.065374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.065550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.065759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.065940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.066156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.066744] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.066985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [80.067175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [80.067350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [80.067524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.067721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.067902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.068078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.068267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.068563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.068876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.069167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.069458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.069755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.070702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.071004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.097522] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.097830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.097874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [80.098079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [80.098141] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.098264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [80.098445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.098410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.098668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.098854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.099035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.099250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.099891] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.100120] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [80.100291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [80.100456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [80.100647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.100816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.100979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.101142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.101317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.101614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.101894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.102167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.102436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.102723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.103647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.103935] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.130927] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.131235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [80.131430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [80.131653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [80.131659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.131840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.131947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.132018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.132196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.132211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.132371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.132589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.132918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.133216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.133503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.133810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.134096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.135385] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.135721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.147949] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.180938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.181302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.181544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.181813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.181818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.182032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.182176] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.182246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.182459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.182508] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.182690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.182928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.183267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.183585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.183914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.184227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.184533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.185524] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.185873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.214250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.214654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [80.214648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.214885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [80.214970] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.215095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [80.215294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.215259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.215490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.215728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.215928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.216160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.216495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.216846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.217163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.217477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.217790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.218801] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.219106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.247469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.247746] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.247781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.247975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.248024] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.248157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.248280] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.248334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.248511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.248705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.248884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.249100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.249407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.249722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.250015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.250305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.250619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.251548] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.251867] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.281137] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.281440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [80.281688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [80.281695] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.281890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [80.281988] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.282083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.282273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.282263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.282465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.282665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.282875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.283180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.283472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.283791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.284080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.284366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.285402] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.285725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.314113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.314418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [80.314675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [80.314665] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.314864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [80.314940] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.315047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.315226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.315195] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.315406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.315583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.315793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.316081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.316359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.316646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.316916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.317183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.318074] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.318358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.347617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.347668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [80.347879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [80.347906] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.348068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [80.348156] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.348249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.348427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.348672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.348860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.349038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [80.349217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [80.349394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [80.349570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [80.349769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.349948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.350125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.350300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.350512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.350821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.351098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.351369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.351659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.351929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.352906] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.353191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.354073] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [80.354310] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [80.380863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.381113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.381319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.381517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.381758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.381859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.382056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.382058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.382286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.382330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.382642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.382946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.383235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.383521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.383831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.384745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.385044] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.414632] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.414946] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.415224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.415869] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454] <7> [80.433888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [80.434165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [80.434318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.434449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.434573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.434731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.434893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.435093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.435274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.435447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.435815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.435978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.436623] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.436788] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.464236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.464518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.464803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.464811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.465029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.465157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.465244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.465456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.465470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.465726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.466092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.466440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.466892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.467244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.467606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.468821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.469176] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.497914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [80.498187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [80.498411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.498677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.498686] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.498881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.498984] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.499076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.499262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.499308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.499833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [80.500046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [80.500241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.500430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.500648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.500842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.501047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.501373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.501710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.502033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.502346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.502678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.504360] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.504719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.530940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [80.531197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [80.531397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.531644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.531695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.531888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.531947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.532080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.532226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.532320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.532838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [80.533046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [80.533239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.533428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.533641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.533819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.534008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.534308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.534636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.534928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.535212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.535497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.536607] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.536913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.564232] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [80.564503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [80.564776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.564777] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.564996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.565095] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.565211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.565426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.565396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.565694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.566240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [80.566463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [80.566699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.566909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.567117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.567324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.567551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.568081] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [80.568284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [80.568472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.568684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.568878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.569069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.569271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.569609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.569924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.570239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.570549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.570874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.571773] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.572076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.597662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.597619] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.597907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.598018] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.598108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.598301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.598345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.598495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.598701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.598945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.599465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.599692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.599889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.600078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.600270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.600460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.600693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.601148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.601333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.601508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.601702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.601881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.602054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.602240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.602538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.602846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.603140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.603416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.603697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.604612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.604883] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.630986] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [80.631282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [80.631505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.631772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.631777] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.631988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.632115] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.632196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.632429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.632449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.632809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.633132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.633446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.633780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.634096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.635172] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.635511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.664201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [80.664471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [80.664741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.664744] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.664959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.665067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.665171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.665379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.665373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.665668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.666027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.666372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.666731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.667068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.667401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.668723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.669050] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.697604] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.697813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [80.697918] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.698042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [80.698198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.698243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.698436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.698653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.698847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.699073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [80.699403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [80.699747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [80.700064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.700376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [80.700709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [80.701718] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.702041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.730821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [80.731088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [80.731297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.731496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.731750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.731743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.731946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.732042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.732177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.732322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.732510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.732852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.733170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.733484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.733821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.734984] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.735314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.764330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [80.764730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [80.764734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.764971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.765081] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.765193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.765409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.765398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.765651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.765864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.766080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.766292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.766499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.767736] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.768095] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.814171] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [80.814440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [80.814710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.814711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.814918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.815017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.815113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.815304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.815295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.815537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.816427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.816784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.817107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.817424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.817764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.818761] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.819102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.847616] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.848056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.848436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.849789] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455] <7> [80.878449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [80.878683] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [80.878766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.878839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.878908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.878975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.879075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.879197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.879309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.879418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.879527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.879664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.880267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.880436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.914247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [80.914623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [80.914632] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.914876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.915111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.915096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.915343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.915485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.915627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.915919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.916324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.916740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.917122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.917498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.917895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.919171] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.919526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.947606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.947848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [80.947960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.948152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [80.948251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.948388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.948627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.948835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.949035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.949285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.949655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.949989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.950308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.950649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.950966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.952144] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.952475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.980752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [80.981002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [80.981208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.981405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.981654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.981651] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.981851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.981951] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.982098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.982233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.982433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.982793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.983090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.983380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.983690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.984704] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.985010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.014110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [81.014347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [81.014549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.014785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.014787] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.014989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.015083] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.015184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.015358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.015414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.015761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.016084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.016398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.016734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.017052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.017964] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.018288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.047415] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.047583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.047707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.047916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.047881] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.048115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.048161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.048311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.048504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.048761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.049098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.049419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.049736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.050024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.050308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.051141] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.051450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.080811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [81.081047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [81.081247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.081443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.081671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.081681] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.081870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.081976] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.082100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.082252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.082606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [81.082810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [81.082995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.083183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.083372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.083584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.083774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.084073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.084346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.084631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.084893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.085139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.085909] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.086149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.113838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.113951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.114019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.114085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.114151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.114216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.114296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.114467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.114540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.114636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.114638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.114717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.114760] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.114784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.114849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.114859] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.114920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.115034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.115145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.115256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.115366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.115474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.115888] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.116036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.147586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.147698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.147884] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.147935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.148129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.148137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.148312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.148492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.148685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.148919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.149381] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.149595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.149781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.149954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.150128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.150302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.150487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.151031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.151221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.151397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.151593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.151769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.151942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.152126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.152425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.152743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.153038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.153329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.153644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.154523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.154829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.180668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [81.180877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [81.181046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.181211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.181374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.181535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.181745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.181780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.182006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.182213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [81.182241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.182384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [81.182567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.182739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.182900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.183063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.183237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.183674] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [81.183849] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [81.184009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.184169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.184330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.184492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.184777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.185064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.185335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.185622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.185889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.186154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.187022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.187274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.214589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.214945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.215201] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456] <7> [81.215235] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.237481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.237776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [81.237890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [81.237985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [81.238073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.238159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.238242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [81.238322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [81.238402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.238480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.238584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [81.238663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [81.238741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.238817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.238892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.238965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.239065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.239327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.239422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [81.239494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [81.239577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [81.239645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.239714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.239781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [81.239847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [81.239912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.239977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.240041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [81.240106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [81.240172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.240239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.240304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.240368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.240441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.240569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.240682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.240794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.240902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.241009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.241974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.242123] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.246921] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [81.265496] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457] <7> [81.281576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.281901] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.282054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.284753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.285351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.285486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.314139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.314581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.314605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [81.314876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [81.314935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.315131] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [81.315275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.315377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.315627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.315868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.316100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.316396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.316822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.317185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.317534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.317938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.318281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.319416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.319804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.347441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.347761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.347810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [81.348024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [81.348068] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.348222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [81.348346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.348417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.348643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.348845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.349039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.349274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.349631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.349950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.350264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.350594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.350907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.352107] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.352441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.380697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.381033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [81.381266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [81.381480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [81.381760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.381739] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.381957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.382044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.382149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.382340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.382324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.382594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.382926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.383243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.383576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.383892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.384200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.385263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.385613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.414222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.414509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [81.414751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [81.414753] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.414939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [81.415029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.415117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.415292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.415284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.415470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.415670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.415883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.416187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.416481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.416803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.417095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.417383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.418336] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.418655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.447291] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.447591] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.447635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [81.447844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [81.447889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.448038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [81.448162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.448231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.448422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.448637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.448832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.449061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.449389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.449720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.450034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.450343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.450689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.451689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.451992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.480750] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.481048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [81.481247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [81.481430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [81.481651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.481655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.481838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.481927] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.482020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.482198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.482177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.482414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.482746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.483042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.483332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.483643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.483931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.485164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.485456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.498117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.530784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.531293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [81.531635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [81.531655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.531895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [81.532141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.532124] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.532379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.532524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.532671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.532906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.533195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.533633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.534027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.534414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.534814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.535190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.536298] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.536663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.564075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.564401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [81.564690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [81.564684] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.564914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [81.565028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.565124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.565332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.565351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.565602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.565814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.566066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.566425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.566780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.567095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.567405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.567730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.568809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.569134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.597272] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.597609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [81.597575] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.597821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [81.597885] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.598019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [81.598170] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.598212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.598403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.598624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.598818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.599045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.599377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.599717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.600007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.600290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.600622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.601609] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.601907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.630886] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.631169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [81.631365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [81.631586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [81.631598] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.631768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.631873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.631948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.632125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.632130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.632300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.632509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.632998] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.633233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [81.633414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [81.633609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [81.633771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.633932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.634096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.634258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.634433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [81.634733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [81.635006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [81.635276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.635558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [81.635825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [81.636759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.637038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.663989] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.664299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [81.664506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [81.664746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [81.664757] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.664945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.665055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.665135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.665327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.665333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.665518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.665798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.666282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.666551] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [81.666751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [81.666943] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [81.667132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.667321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.667511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.667718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.667911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [81.668206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [81.668498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [81.668803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.669091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [81.669384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [81.670557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.670866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.697585] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.697978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.698315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.701554] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458] <7> [81.727541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.727786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [81.727872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [81.727945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [81.728015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.728084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.728152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.728218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.728284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.728350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.728415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.728481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.728571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.728639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.728706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.728772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.728868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.729068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.729162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [81.729234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [81.729300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [81.729366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.729432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.729497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.729578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.729646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.729711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.729779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.729846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.729912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.729977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.730042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.730108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.730178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.730292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.730403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.730512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.730633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.730746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.731438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.731679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.748815] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459] <7> [81.764560] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.764845] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.765046] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.772172] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.772974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.773129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.797322] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.797562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.797749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [81.797863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.797995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [81.798145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.798213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [81.798424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.798653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.798863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.799060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.799311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.799971] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.800247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [81.800453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [81.800697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [81.800893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.801088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.801283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.801475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.801704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.802034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.802357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.802692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.803012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.803330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.804333] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.804664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.830673] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.830994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [81.831208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [81.831405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [81.831638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.831650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.831824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.832004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.831995] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.832182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.832289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.832395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.832724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.833034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.833326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.833637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.833930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.834963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.835272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.863937] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.864284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [81.864511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [81.864782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [81.864782] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.864995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.865100] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.865193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.865390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.865393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.865756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.866064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.866404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.866741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.867060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.867379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.867714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.868806] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.869133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.897577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.897561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.897883] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [81.897887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.898097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [81.898172] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.898295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [81.898487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.898698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.898894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.899086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.899315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.899673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.899999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.900316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.900643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.900932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.901962] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.902266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.930572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.930879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [81.931088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [81.931284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [81.931474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.931703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.931718] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.931899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.932016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.932091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.932293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.932317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.932692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.932989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.933281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.933591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.933881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.934844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.935151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.963980] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.964314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [81.964584] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [81.964586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.964792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [81.964885] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.964986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.965178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.965163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.965375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.965659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.965884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.966193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.966491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.966806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.967099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.967395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.968710] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.969028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.981045] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.013954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.014380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.014682] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.014689] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.014917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.015016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.015136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.015352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.015320] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.015589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.015807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.016068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.016438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.016821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.017169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.017536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.017856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.018863] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.019191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.047316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.047655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.047689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [82.047922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [82.047976] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.048140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [82.048274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.048352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.048589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.048803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.049012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.049262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.049632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.049957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.050272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.050618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.050930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.052030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.052359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.080586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.080918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.081135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.081333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.081565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.081576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.081755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.081855] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.081937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.082112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.082109] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.082336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.082697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.083003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.083296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.083603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.083890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.084887] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.085187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.114178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.114485] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [82.114739] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [82.114750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.114937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [82.115044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.115127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.115318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.115322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.115542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.115721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.115935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.116242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.116587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.116879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.117163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.117447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.118399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.118723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.147175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.147486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [82.147736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [82.147749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.147937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [82.148041] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.148130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.148323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.148315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.148534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.148728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.148958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.149291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.149653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.149944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.150230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.150534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.151494] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.151831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.180543] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.180696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026 <7> [82.180866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.180937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [82.181145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025 <7> [82.181141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.181342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.181551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.181749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.181942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.182133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [82.182323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.182535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.182724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.182914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.183106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.183296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.183485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.184007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.184563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026 <7> [82.184771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [82.184961] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025 <7> [82.185148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.185336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.185546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.185737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.185924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [82.186112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.186302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.186491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.186702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.186883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.187059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.187233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.187424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.187743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.188040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.188334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.188645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.188938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.189926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.190247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.191225] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [82.191465] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [82.230494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.230824] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.231043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.231246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.231444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.231700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.231693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.231937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.231990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.232263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.232444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.232670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.232863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.233052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.233245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.233438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.233662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.234149] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.234358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.234570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.234749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.234927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.235104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.235291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.235606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.235902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.236190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.236477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.236784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.237723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.238024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.263882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [82.264102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [82.264275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.264443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.264648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.264819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.264736] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.265016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.265096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.265381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.265443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [82.265648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [82.265818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.265986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.266149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.266310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.266485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.266923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [82.267095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [82.267258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.267421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.267609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.267774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.267949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.268222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.268492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.268780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.269048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.269318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.270229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.270492] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.297173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.297423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.297659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.297740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.297847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.298027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.298122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.298205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.298434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.298421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.298780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.299085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.299378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.299692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.299982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.301101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.301385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.330536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.330875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.330948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [82.331175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.331252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [82.331480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.331719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.331924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.332122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.332372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.332726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.333032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.333323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.333626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.333913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.334936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.335247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.363903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [82.364235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [82.364470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.364731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.364741] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.364943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.365049] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.365145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.365335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.365386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.365751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.366076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.366393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.366728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.367039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.368289] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.368658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.397263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [82.397573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [82.397573] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.397806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.397908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.398022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.398236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.398215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.398445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.398710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.399047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.399370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.399744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.400060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.400374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.401344] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.401691] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.447105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.447398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.447678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.447669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.447885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.447972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.448085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.448279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.448254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.448567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.448908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.449244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.449582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.449901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.450215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.451145] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.451477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.480529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.480591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [82.480821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [82.480847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.481024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.481124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.481220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.481411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.481632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.481852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.482158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.482455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.482761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.483048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.483336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.484344] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.484689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.513852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [82.514104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [82.514308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.514545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.514553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.514746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.514850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.514938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.515128] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.515171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.515519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.515839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.516152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.516460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.516794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.517994] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.518305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.547534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [82.547532] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.547801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [82.547873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.548023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.548175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.548238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.548449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.548676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.548929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.549286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.549689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.550009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.550318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.550656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.551687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.552012] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.580446] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [82.580708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [82.580716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.580913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.581008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.581108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.581302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.581284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.581516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.581757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.582087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.582407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.582740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.583052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.583360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.585105] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.585415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.613895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [82.614152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [82.614361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.614609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.614621] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.614812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.615008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.615017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.615204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.615397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.615355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.615626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.615820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.616667] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.616972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.663763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [82.663981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [82.664155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.664322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.664525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.664536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.664697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.664819] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.664902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.665074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.665187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.665464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.665752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.666024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.666288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.667122] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.667396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.697520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.697925] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.698256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.700390] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460] <7> [82.701602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [82.701898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [82.702128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.702344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.702582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.702794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.703058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.703632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [82.703856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [82.704064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.704269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.704477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.704696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.704920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.705270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.705635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.705980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.706323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.706681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.707991] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.708328] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.730616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [82.730875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [82.731090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.731300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.731571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.731562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.731799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.731912] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.732055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.732233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.732721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [82.732951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [82.733157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.733363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.733596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.733805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.734024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.734376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.734739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.735080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.735421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.735769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.736998] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.737305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.764151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [82.764415] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [82.764670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.764678] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.764871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.764983] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.765067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.765257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.765263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.765505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.765997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [82.766199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [82.766388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.766596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.766790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.766981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.767185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.767744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [82.767947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [82.768136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.768324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.768527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.768720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.768925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.769242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.769603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.769925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.770236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.770563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.771517] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.771815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.797104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [82.797383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [82.797641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.797645] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.797854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.797947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.798054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.798248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.798227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.798512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.798991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [82.799186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [82.799364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.799555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.799734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.799912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.800102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.800548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [82.800740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [82.800916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.801090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.801268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.801444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.801646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.801952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.802242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.802527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.802798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.803054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.804051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.804300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.830547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [82.830819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [82.831041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.831254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.831466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.831741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.831725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.832047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.832264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.832355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.832640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.832996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.833338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.833726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.834040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.835008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.835330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.863778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [82.864023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [82.864227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.864421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.864667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.864662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.864865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.864960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.865094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.865236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.865427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.865769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.866085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.866400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.866733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.867651] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.867981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.897145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [82.897411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [82.897679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.897674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.897889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.897975] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.898087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.898281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.898247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.898531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.898869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.899195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.899532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.899828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.900117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.901124] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.901431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.930459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [82.930756] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [82.930761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.930984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.931078] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.931196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.931408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.931375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.931665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.931903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.932235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.932573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.932895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.933210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.933544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.934740] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.935061] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.964150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [82.964398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [82.964648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.964647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.964855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.964948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.965052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.965244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.965222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.965500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [82.965829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [82.966148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [82.966462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.966794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [82.967102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [82.968120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.968441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.997085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [82.997342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [82.997616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.997615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.997838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.997935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.998049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.998257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.998230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.998525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.998886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.999236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.999615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.999956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.000292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.001997] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.002330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.030502] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.030849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.031163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.032624] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461] <7> [83.034549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.034944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [83.035176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [83.035379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [83.035620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.035827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.036022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.036215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.036406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.036661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [83.036867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [83.037057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [83.037248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.037437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.037648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.037841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.038081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.038424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.038767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.039088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.039403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.039731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.040817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.041121] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.046649] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [83.066024] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462] <7> [83.067562] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.097129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.097578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.097635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.097905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.097928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.098154] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.098254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.098396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.098644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.098882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.099121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.099410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.099835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.100220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.100633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.101011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.101384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.102570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.102930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.130502] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.130657] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.130991] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.131091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [83.131362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [83.131350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.131635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [83.131860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.132076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.132292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.132515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.132792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.133168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.133538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.133889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.134236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.134594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.136314] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.136702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.163852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.164241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.164550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.164562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.164796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.165031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.165056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.165262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.165515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.165450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.165733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.165985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.166352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.166734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.167075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.167413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.167778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.168943] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.169295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.197337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.197698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [83.197649] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.197912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [83.198110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [83.198064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.198303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.198392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.198522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.198719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.198913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.199156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.199511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.199836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.200152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.200496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.200807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.201832] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.202155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.230432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.230880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [83.230781] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.231109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [83.231235] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.231322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [83.231556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.231606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.231768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.231977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.232182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.232430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.232986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.233264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [83.233501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [83.233709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [83.233914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.234118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.234324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.234577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.234786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.235109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.235427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.235765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.236076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.236383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.237452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.237794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.263899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.264235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [83.264506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [83.264522] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.264723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [83.264932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.264969] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.265139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.265348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.265328] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.265664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.265903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.266390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.266671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [83.266869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [83.267058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [83.267246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.267434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.267644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.267834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.268038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.268359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.268694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.269007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.269304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.269620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.270591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.270862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.280681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.313722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.314094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.314343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.314643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.314626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.314868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.315081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.315070] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.315295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.315429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.315530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.315768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.316373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.316655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.316856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.317049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.317239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.317429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.317639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.317832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.318039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.318365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.318703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.319019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.319332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.319666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.320719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.321051] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.347086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.347408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [83.347678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [83.347675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.347878] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [83.348069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.348090] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.348261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.348473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.348421] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.348668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.348896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.349532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.349786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [83.349985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [83.350173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [83.350361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.350574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.350768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.350957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.351162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.351505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.351827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.352139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.352470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.352784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.354108] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.354391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.380353] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.380713] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.380676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.380928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.381127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.381084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.381320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.381414] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.381549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.381748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.381942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.382177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.382529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.382857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.383174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.383526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.383838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.384940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.385264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.414052] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.414367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [83.414627] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [83.414640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.414829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [83.415022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.415053] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.415217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.415412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.415378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.415647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.416407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.416776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.417098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.417411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.417738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.418044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.419120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.419447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.447027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.447372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [83.447678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [83.447666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.447901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [83.448115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.448117] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.448329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.448493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.448596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.448807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.449060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.449417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.449774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.450090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.450402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.450734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.451849] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.452185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.480507] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.480996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.481361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.482760] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463] <7> [83.485279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.485736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [83.485983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [83.486193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [83.486397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.486630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.486837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.487032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.487226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.487418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.487633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.487827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.488018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.488206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.488395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.488611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.488872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.489191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.489502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.489781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.490045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.490301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.491309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.491578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.501673] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464] <7> [83.502725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.530428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.530903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.530860] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.531185] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.531352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.531441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.531726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.531781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.531946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.532161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.532377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.532672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.533049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.533403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.533779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.534125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.534440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.535395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.535721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.563801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.564161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [83.564397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [83.564680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.564746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [83.564963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.565026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.565176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.565389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.565345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.565624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.565882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.566243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.566620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.566937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.567250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.567581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.569038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.569372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.596995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.597331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.597611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.597615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.597831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.597945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.598040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.598252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.598251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.598485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.598696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.598949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.599311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.599708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.600056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.600397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.600769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.601847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.602175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.630478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.630762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.630849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.631137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [83.631183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.631404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [83.631665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [83.631881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.632092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.632305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.632528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.632794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.633163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.633690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.634035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.634377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.634759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.635926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.636285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.663731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.664091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [83.664322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [83.664591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [83.664588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.664813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.664924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.665021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.665229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.665230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.665458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.665716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.666082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.666430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.666840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.667186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.667556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.668728] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.669058] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.697056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.697402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [83.697687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [83.697693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.697895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [83.697992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.698088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.698281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.698273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.698507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.698704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.698934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.699267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.699615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.699933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.700247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.700577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.701683] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.702022] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.714309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.747024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.747405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.747688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.747702] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.747907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.748105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.748118] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.748301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.748517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.748472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.748715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.748955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.749493] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.749760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.749962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.750156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.750344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.750560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.750755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.750945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.751147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.751499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.751831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.752149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.752489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.752806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.753828] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.754139] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.780569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.780484] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.780902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [83.780955] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.781134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [83.781349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [83.781318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.781613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.781832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.782044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.782252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.782613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.783164] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.783470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [83.783693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [83.783900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [83.784108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.784314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.784543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.784753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.784977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.785333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.785706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.786055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.786396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.786772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.788191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.788494] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.813664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.813997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.814224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.814482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.814492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.814698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.814844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.814895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.815085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.815145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.815275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.815522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.816129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.816383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [83.816617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [83.816810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [83.816997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.817184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.817373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.817584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.817788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.818113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.818429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.818758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.819071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.819379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.820400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.820724] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.847297] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.847659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.847701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [83.847945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [83.847998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.848165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [83.848308] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.848380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.848622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.848839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.849056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.849308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.849987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.850266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [83.850670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [83.850870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [83.851058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.851246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.851474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.851666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.851948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [83.852284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.852623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.852940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.853251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.853601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.854634] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.854939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.880483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.880520] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.880839] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.880894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [83.881146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [83.881151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.881373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [83.881635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.881853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.882063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.882270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.883300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [83.883658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [83.883960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [83.884232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.884508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [83.884781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [83.885812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.886071] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.913888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [83.914187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [83.914487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [83.914495] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.914730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.914847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.914961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.915192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.915179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.915421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.915696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [83.915924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [83.916151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [83.916378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [83.916626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.916855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.917079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.917303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.917596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.917993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.918378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.918785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.919163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.919585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.920821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.921182] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.922111] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [83.922367] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [83.947032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.947354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.947686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.947673] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.947942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.948028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.948180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.948359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.948410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.949130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.949564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.949921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.950266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.950624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.950939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.951931] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.952233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.980475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.980858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.981196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.985380] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465] <7> [83.986668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [83.987013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [83.987266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.987539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.987781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.988013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.988305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.988732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.989119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.989501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.989841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.990183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.991370] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.991704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.013698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.013978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.014219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.014499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.014508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.014738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.014859] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.014967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.015191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.015242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.015650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.016040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.016415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.016822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.017161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.018317] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.018689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.047301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [84.047640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [84.047626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.047887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.047956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.048113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.048268] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.048331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.048574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.048843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.049209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.049604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.049949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.050288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.050646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.051702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.052033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.080298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [84.080606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [84.080610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.080830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.080929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.081044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.081256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.081227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.081492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.081749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.082114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.082499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.082834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.083146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.083508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.084588] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.084916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.113661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [84.113902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [84.114102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.114295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.114532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.114537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.114731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.114831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.114965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.115109] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.115297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.115633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.115947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.116253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.116582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.117471] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.117789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.146914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.147190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.147408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.147669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.147741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.147945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.147972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.148140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.148248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.148379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.148742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.149068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.149387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.149717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.150010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.150915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.151218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.180238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [84.180501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [84.180485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.180690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.180762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.180872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.181014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.181050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.181226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.181462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.181769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.182066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.182357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.182670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.182961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.183878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.184179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.213561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.213797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.213996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.214188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.214382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.214616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.214622] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.214858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.214915] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.215187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.215189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.215526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.215832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.216118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.216405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.217391] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.217717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.247138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [84.247364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [84.247599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.247600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.247786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.247873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.247966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.248143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.248124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.248966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.249480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [84.249667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [84.249833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.249994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.250157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.250319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.250520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.250800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.251073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.251342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.251623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.251889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.252771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.253055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.280239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [84.280479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [84.280481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.280669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.280754] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.280849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.281027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.281007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.281203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.281410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.281887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [84.282063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [84.282227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.282389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.282571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.282735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.282908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.283185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.283483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.283754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.284020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.284283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.285219] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.285523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.313534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [84.313741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [84.313912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.314077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.314242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.314404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.314604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.314611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.314771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.314867] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.314935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.315096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.315099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.315455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [84.315621] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [84.315781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.315941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.316102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.316264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.316459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.316622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.316782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.316942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.317262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [84.317468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [84.317630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.317790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.317951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.318113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.318276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.318462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.318618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.318767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.319496] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.319756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.363507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.363741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.363922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.364092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.364259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.364453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.364462] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.364652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.364717] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.364951] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.365094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.365271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.365450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.365615] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.365779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.365940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.366112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.366549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.366721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.366883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.367045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.367208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.367369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.367583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.367860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.368131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.368396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.368680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.368948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.369745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.370013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.397467] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.397877] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.398183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.401529] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466] <7> [84.402616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [84.402907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [84.403122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.403320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.403544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.403740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.403992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.404328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.404669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.404964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.405251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.405581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.406719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.407014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.430211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.430507] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.430609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.430831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.430850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.431044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.431165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.431256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.431507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.431763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.432120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.432490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.432833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.433169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.433526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.434650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.434979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.463852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [84.464127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [84.464340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.464599] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.464678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.464880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.464905] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.465073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.465185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.465308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.465672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.465999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.466319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.466656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.466971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.468002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.468333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.496819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [84.497071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [84.497274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.497546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.497521] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.497730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.497804] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.497908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.498063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.498121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.498439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.498737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.499027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.499313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.499619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.500578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.500876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.530179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [84.530450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [84.530441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.530641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.530718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.530832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.531026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.530995] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.531220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.531563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.531914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.532234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.532563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.532856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.533142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.533942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.534244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.563574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.563836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.564035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.564222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.564441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.564452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.564625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.564755] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.564842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.565026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.565152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.565465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.565760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.566049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.566338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.567218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.567560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.596892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [84.597141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [84.597346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.597588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.597659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.597856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.597896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.598048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.598174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.598278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.598631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.598964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.599279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.599615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.599932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.600974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.601300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.630139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [84.630380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [84.630625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.630631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.630826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.630930] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.631022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.631214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.631204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.631463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.631795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.632115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.632453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.632767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.633079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.634077] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.634399] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.664441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.664616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [84.664781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.664886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [84.665081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.665122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.665340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.665576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.665791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.666046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.666441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.666796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.667142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.667506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.667837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.668852] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.669181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.696834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [84.697111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [84.697331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.697596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.697600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.697814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.697919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.698023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.698217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.698267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [84.698654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.699009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.699355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.699721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.700060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.701169] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.701517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.730438] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.730781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.731084] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.736504] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467] <7> [84.738551] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.738978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [84.739229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [84.739493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [84.739710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.739924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.740136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.740335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.740548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.740739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [84.740934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [84.741111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [84.741285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.741473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.741650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.741823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.742042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.742330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.742604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.742862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.743100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.743336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.744543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.744776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.746379] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [84.766634] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468] <7> [84.769096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.796878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.797295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.797614] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.797624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.797874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.797973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.798125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.798311] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.798358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.798699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.798917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.799174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.799764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.800046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.800268] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.800502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.800711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.800917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.801126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.801334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.801574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.801938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.802289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.802657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.803007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.803352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.804452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.804793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.830266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.830589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.830630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [84.830856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [84.830908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.831069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [84.831207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.831278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.831514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.831718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.831913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.832141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.832686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.832938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [84.833133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [84.833322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [84.833537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.833728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.833917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.834103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.834305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.834648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.834968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.835280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.835606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.835919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.837016] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.837321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.863552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.863857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.864067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.864262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.864488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.864497] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.864687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.864791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.864880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.865068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.865062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.865292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.865888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.866141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.866339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.866558] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.866747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.866932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.867121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.867308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.867527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.867857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.868175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.868505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.868797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.869082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.869983] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.870248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.897071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.897461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [84.897441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.897689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [84.897741] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.897892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [84.898013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.898088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.898282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.898508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.898713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.898944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.899580] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.899839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [84.900037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [84.900227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [84.900437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.900632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.900820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.901008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.901212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.901551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.901846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.902135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.902420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.902691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.903572] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.903826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.930094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.930475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [84.930709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [84.930577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.930923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [84.931056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.931134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.931342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.931452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.931661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.931859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.932086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.932701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.932952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [84.933148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [84.933336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [84.933544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.933732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.933921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.934110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.934314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.934636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.934929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.935218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.935500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.935766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.936633] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.936884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.963427] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.963511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.963757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.963799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [84.964010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [84.964048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.964205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [84.964418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.964611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.964805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.964997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.965233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.965585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.965907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.966220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.966542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.966838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.968142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.968460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.980535] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.013437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.013820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.014092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.014340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.014626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.014849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.014775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.015064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.015194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.015275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.015568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.015552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.015920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.016270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.016639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.016983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.017327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.018357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.018721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.046853] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.047181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [85.047461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [85.047479] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.047679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [85.047891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.047929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.048101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.048311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.048301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.048541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.048788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.049150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.049532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.049875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.050215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.050576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.051679] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.052001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.080308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.080454] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.080843] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.080861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.081193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.081231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.081579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.081874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.082157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.082462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.082749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.083069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.083489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.083943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.084397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.084811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.085200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.086597] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.087004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.113823] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.114293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [85.114828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [85.114894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.115181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [85.115499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.115440] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.115769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.115864] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.116029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.116302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.116655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.117085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.117482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.117917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.118322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.118750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.119839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.120262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.146790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.147217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [85.147635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [85.147765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.147930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [85.148204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.148263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.148576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.148746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.148858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.149114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.149425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.149823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.150210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.150635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.151063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.151478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.152580] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.152998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.180528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.180996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.181449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.184824] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469] <7> [85.187282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.187774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [85.188066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [85.188341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [85.188682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.188992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.189245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.189546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.189805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.190044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.190293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.190554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.190789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.191029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.191273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.191528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.191756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.192049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.192326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.192666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.192920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.193152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.193995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.194220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.201137] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470] <7> [85.202006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.230065] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.230532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [85.230611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.230842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [85.231129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [85.231107] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.231435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.231583] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.231704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.231967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.232250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.232625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.233024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.233441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.233875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.234292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.234708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.235695] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.236093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.263559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.263984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [85.264344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [85.264765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [85.264869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.265047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.265328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.265357] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.265669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.265847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.265930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.266200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.266607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.266963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.267331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.267730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.268104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.269102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.269483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.296748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.297178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [85.297595] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.297714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [85.298007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [85.298108] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.298288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.298586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.298706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.298978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.299300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.299747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.300326] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.300698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [85.300971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [85.301197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [85.301457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.301677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.301916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.302135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.302362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.302778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.303127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.303486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.303834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.304152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.305051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.305366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.330435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.330550] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.330873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [85.331039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.331241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [85.331510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.331585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [85.331848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.332141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.332403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.332641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.332909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.333465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.333752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [85.333982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [85.334206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [85.334494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.334763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.334988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.335236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.335503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.335857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.336182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.336525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.336910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.337199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.338185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.338478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.363431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.363548] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.363793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [85.363981] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.364075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [85.364332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [85.364364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.364656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.364900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.365137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.365399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.365666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.366171] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.366497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [85.366725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [85.366947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [85.367208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.367468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.367711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.367920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.368142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.368508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.368849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.369161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.369550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.369869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.370682] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.370973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.396853] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.397341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [85.397988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [85.397988] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.398331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [85.398512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.398700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.398972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.398970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.399236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.399613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.399935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.400630] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.400944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [85.401177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [85.401466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [85.401688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.401898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.402099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.402297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.402551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.402874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.403178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.403531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.403801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.404052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.404992] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.405242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.413863] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.446650] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.446985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [85.447237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [85.447536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [85.447657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.447789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.448071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.448104] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.448320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.448532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.448630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.448932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.449300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.449720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.450084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.450446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.450795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.451713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.452075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.480075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.480493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [85.480596] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.480774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [85.481032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [85.481045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.481279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.481472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.481610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.481849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.482129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.482421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.482786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.483141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.483574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.483921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.484263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.485332] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.485755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.513399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.513543] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.513792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [85.513988] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.514075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [85.514335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [85.514425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.514656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.514953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.515193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.515511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.515778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.516139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.516564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.516911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.517255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.517631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.518610] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.518973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.546879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.547238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [85.547648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [85.547766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.547912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [85.548164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.548251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.548433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.548725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.548693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.548961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.549226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [85.549633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.550026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.550390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.550785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.551126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.552104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.552510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.579951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.580338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [85.580805] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [85.580818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.581153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [85.581305] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.581474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.581761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.581788] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.582006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.582242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.582557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [85.582930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [85.583291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [85.583732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.584078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [85.584435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [85.585434] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.585793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.613523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.613602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [85.613950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [85.614021] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.614259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [85.614486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.614603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.614887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.615163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.615537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.615804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [85.616059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [85.616314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [85.616636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [85.616904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.617145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.617415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.617659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.617938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.618332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.618780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.619222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.619714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.620200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.621449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.621820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.622755] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [85.623035] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [85.646718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.647074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.647457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.647545] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.647745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.648021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.648030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.648341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.648497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.648745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.649151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.649579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.649981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.650324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.650757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.651601] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.651907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.680517] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.681013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.681409] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471] <7> [85.681444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.701458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [85.701779] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [85.702070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.702346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.702700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.702973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.703278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.703701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.704106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.704480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.704872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.705216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.706202] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.706689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.730025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.730468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.730478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.730788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.730997] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.731104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.731457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.731507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.731760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.732153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.732659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.733050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.733446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.733837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.734210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.735505] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.735916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.763430] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.763839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [85.763937] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.764229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [85.764424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.764637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.764927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.765203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.765580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.765956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.766427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.766906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.767335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.767822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.768215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.769417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.769850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.796723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [85.797072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [85.797433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.797564] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.797721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.797998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.798077] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.798292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.798556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.798666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.799070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.799484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.799923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.800326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.800760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.801903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.802260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.830052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [85.830508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [85.830638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.830816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.831109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.831126] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.831427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.831609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.831727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.832045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.832569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [85.832813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [85.833076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.833297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.833585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.833830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.834064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.834425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.834770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.835110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.835563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.835935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.836836] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.837196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.863488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.863541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.863839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.864029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.864143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.864471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.864509] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.864793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.865038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.865311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.865888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.866128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.866377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.866653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.866885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.867103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.867333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.867753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.868097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.868480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.868819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.869155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.870121] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.870463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.896781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [85.897173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [85.897586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.897721] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.897876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.898183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.898207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.898514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.898693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.898836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.899370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [85.899609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [85.899825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.900029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.900232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.900480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.900708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.901212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [85.901509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [85.901744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.901940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.902133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.902322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.902590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.902913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.903203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.903534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.903895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.904215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.905102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.905393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.929990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.930340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.930753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.930902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.931042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.931318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.931427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.931727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.931853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.932014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.932565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.932830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.933092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.933313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.933631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.933848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.934040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.934461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [85.934647] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [85.934822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.934988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.935153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.935316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.935540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.935798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.936045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.936279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.936599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.936818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.937506] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.937727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.963528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.963640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [85.963991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [85.964019] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.964294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.964491] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.964654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.964937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.965258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.965630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.966034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.966455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.966867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.967210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.967617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.968589] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.968903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.996661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [85.996955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [85.997207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.997500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.997626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.997743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.998037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.998067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.998313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.998484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.998736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.999139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.999526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.999885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.000227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.001267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.001667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.029968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [86.030285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [86.030691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.030786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.031021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.031292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.031275] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.031634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.031753] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.031874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.032123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.032369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.032596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.033516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.033879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.080086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.080536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.080664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.080841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.081125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.081156] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.081473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.081645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.081741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.082053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.082485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.082885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.083275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.083768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.084149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.085228] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.085662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.113514] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.114006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.114456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.114694] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472] <7> [86.138877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [86.139232] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [86.139504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.139722] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.139933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.140139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.140428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.140779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.141107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.141424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.141727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.142018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.143279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.143565] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.163407] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.163475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.163869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.163869] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.164217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.164242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.164617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.164946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.165318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.165797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.166258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.166756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.167251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.167729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.168180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.169492] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.169938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.197026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [86.197469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [86.197517] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.197809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.198127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.198058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.198488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.198591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.198790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.199185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.199673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.200106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.200617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.201079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.201521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.202717] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.203153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.229916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [86.230272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [86.230688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.230811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.230987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.231265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.231296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.231609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.231795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.231911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.232315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.232777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.233216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.233665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.234037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.235445] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.235847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.263291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [86.263695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [86.263819] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.263972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.264239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.264264] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.264546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.264712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.264790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.265095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.265506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.265867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.266212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.266638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.266978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.267867] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.268228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.296574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.296927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.297236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.297599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.297736] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.297857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.298152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.298184] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.298486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.298622] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.298855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.299213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.299604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.299999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.300337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.301255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.301657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.329981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [86.330335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [86.330740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.330833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.331005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.331260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.331278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.331641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.331725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.331943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.332307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.332721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.333082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.333442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.333780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.334745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.335106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.363212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.363640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.363774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.363917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.364176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.364216] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.364489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.364648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.364742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.365016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.365400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.365786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.366131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.366563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.366903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.367981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.368367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.396797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [86.397093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [86.397392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.397525] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.397634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.397887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.397964] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.398141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.398382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.398443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.398976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [86.399234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [86.399520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.399793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.400018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.400260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.400558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.400903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.401268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.401657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.402038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.402392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.403329] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.403759] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.429832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [86.430106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [86.430391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.430533] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.430613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.430845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.430937] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.431119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.431291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.431803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.432362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [86.432618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [86.432873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.433152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.433445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.433690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.433952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.434356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.434744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.435102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.435467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.435806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.436682] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.437001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.463505] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.464002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.464369] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473] <7> [86.464483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.489245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.489699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [86.489934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [86.490134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [86.490320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.490521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.490695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [86.490866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [86.491032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.491193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.491373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [86.491535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [86.491690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.491840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.491984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.492134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.492320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.492765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.492960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [86.493094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [86.493217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [86.493354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.493483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.493606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [86.493726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [86.493849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.493958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.494067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [86.494174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [86.494283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.494403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.494510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.494617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.494732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.494911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.495076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.495234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.495395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.495549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.496483] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.496657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.512800] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [86.531503] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474] <7> [86.548389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.548877] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.549271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.554190] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.555723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.556154] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.579879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.580318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [86.580784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [86.580926] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.581109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [86.581499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.581507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.581859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.581977] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.582162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.582577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.582951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.583751] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.584102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [86.584393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [86.584652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [86.584904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.585165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.585495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.585771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.586030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.586441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.586879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.587252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.587646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.587980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.588838] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.589151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.613300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.613788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.613909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [86.614294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [86.614327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.614716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [86.614872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.615031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.615433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.615773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.616059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.616402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.616857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.617269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.617713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.618129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.618530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.619516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.619853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.646575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.647028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [86.647424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [86.647583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.647724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [86.648032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.648111] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.648419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.648639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.648715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.649004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.649355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.649778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.650175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.650753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.651137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.651626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.652899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.653294] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.680125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.680612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [86.680694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.680972] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [86.681258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [86.681245] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.681610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.681728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.681878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.682143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.682491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.682782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.683173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.683598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.683999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.684404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.684805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.685875] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.686264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.713168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.713644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [86.713722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.713964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [86.714252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [86.714208] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.714616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.714688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.714942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.715200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.715531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.715820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.716213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.716675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.717098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.717515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.717930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.719018] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.719395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.746473] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.746819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [86.747100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [86.747388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [86.747399] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.747620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.747782] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.747860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.748126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.748141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.748442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.748735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.749135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.749583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.749982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.750588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.750971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.752474] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.752884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.764139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.796641] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.797249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [86.797835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [86.797862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.798213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [86.798564] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.798666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.799019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.799096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.799472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.799822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.800254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.800818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.801267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.801746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.802180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.802601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.803719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.804131] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.829918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.830474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [86.830553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.830802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [86.831085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [86.831055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.831391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.831526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.831710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.831975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.832294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.832660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.833076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.833447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.833800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.834195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.834606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.835807] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.836200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.863157] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.863727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.864005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [86.864212] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.864411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [86.864706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [86.864701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.864988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.865309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.865648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.865922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.866220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.866662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.867053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.867524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.867917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.868320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.869525] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.869932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.896792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.897187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [86.897592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [86.897743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.897858] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [86.898111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.898188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.898397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.898638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.898624] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.898906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.899171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [86.899569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [86.899977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [86.900336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.900729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [86.901069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [86.902100] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.902495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.929782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.930210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [86.930622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [86.930746] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.930893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [86.931200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.931194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.931523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.931641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.931769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.932007] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.932273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [86.932713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [86.933070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [86.933479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.933820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [86.934161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [86.935165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.935568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.963494] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.963986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.964418] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.965048] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475] <7> [86.986894] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.987227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [86.987544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [86.987745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [86.987939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.988120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.988292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.988548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.988727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.988883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.989031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.989176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.989312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.989602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.989730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.989855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.990003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.990300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.990499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [86.990613] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [86.990723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [86.990830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.990935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.991034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.991136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.991237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.991347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.991444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.991537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.991624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.991712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.991800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.991885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.991977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.992122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.992262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.992413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.992544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.992670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.993213] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.993428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.997300] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476] <7> [87.009083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.029844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.030253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.030704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.030845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.030981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.031246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.031297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.031621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.031741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.031907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.032142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.032434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.032889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.033142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.033410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.033591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.033772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.033984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.034164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.034349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.034527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.034790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.035033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.035268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.035560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.035776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.036341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.036557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.063266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.063818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [87.063895] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.064167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [87.064417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.064508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [87.064789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.064843] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.065064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.065352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.065670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.065981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.066704] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.067051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [87.067313] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [87.067639] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [87.067891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.068137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.068418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.068651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.068896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.069283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.069738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.070180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.070592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.070951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.071918] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.072258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.096515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.096942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.097288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.097680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.097829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.097958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.098226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.098362] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.098550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.098785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.098860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.099151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.099844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.100157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.100547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.100792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.101089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.101358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.101653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.101904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.102154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.102583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.103030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.103393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.103779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.104096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.104964] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.105272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.130099] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.130575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [87.130652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.130911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [87.131099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.131172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [87.131466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.131530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.131711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.131951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.132242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.132579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.132969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.133343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.133738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.134077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.134430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.135482] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.135840] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.163089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.163568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [87.163648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.163850] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [87.164106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [87.164097] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.164392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.164529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.164638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.164929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.165170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.165474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.165835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.166234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.166616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.166956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.167292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.168353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.168717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.196485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.196828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [87.197073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [87.197307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [87.197683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.197807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.197963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.198210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.198300] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.198507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.198761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.198789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.199142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.199562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.199902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.200298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.200714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.202036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.202453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.213607] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.246361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.246691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.246991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.247256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.247598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.247733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.247854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.248150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.248179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.248439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.248621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.248714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.249081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.249470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.249885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.250238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.250684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.251561] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.251924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.279758] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.280148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [87.280526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [87.280656] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.280788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [87.281037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.281101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.281372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.281545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.281615] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.281857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.282125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.282528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.282884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.283233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.283683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.284056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.285093] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.285487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.313047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.313432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.313537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.313720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.313960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.313947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.314185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.314303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.314453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.314675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.314938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.315214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.315642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.315992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.316363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.316706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.317111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.318143] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.318540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.346472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.346695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [87.346863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [87.347029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [87.347195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.347398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.347564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.347537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.347736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.347875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.347918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.348160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.348173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.348483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.348738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.348981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.349222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.349925] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.350201] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.379596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.379871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [87.380107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [87.380341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [87.380541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.380468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.380757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.380969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.380890] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.381180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.381277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.381475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.381824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.382164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.382586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.382922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.383256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.384220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.384602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.412968] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [87.413388] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [87.413483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.413718] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [87.413908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.414036] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [87.414258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.414374] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [87.414726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.415025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [87.415348] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [87.415669] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [87.416004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [87.416376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [87.416705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [87.417031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [87.417373] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [87.417696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [87.418013] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [87.418344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [87.418663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7> [87.418981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [87.419297] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [87.419679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7> [87.420051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [87.420415] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [87.420735] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [87.421025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [87.421336] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [87.421622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [87.421927] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [87.422278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [87.422645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [87.422951] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [87.423249] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [87.423565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [87.423839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [87.424101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [87.424365] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [87.424616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [87.424880] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [87.425112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [87.425359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [87.425574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [87.425794] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [87.425998] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [87.426197] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [87.426426] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [87.426615] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [87.426801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [87.426977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [87.427153] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [87.427334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [87.427504] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [87.427672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [87.427839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [87.428004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.428165] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.428362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.428539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [87.428688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [87.428835] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.428975] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.429111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [87.429245] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [87.429402] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [87.429531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes <7> [87.429661] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [87.429790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0 <7> [87.429914] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no <7> [87.430034] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [87.430149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes <7> [87.430262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [87.430389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0 <7> [87.430526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.430655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.430838] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1 <7> [87.431001] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on <7> [87.431143] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [87.446104] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [87.447462] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [87.447639] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [87.450189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0 <7> [87.450352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [87.450480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0 <7> [87.450605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [87.450729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.450852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.450998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.451132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [87.451255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.451422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.451548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.451670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [87.451791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.451907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.452020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [87.452159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [87.452353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [87.452537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [87.452716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [87.452888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [87.453064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [87.453494] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <6> [87.466763] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS <7> [87.467552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7> [87.467708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.467845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [87.467978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7> [87.468119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <7> [87.468275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1 <7> [87.468468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [87.468634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [87.468796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [87.468953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [87.469103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [87.479360] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [87.481065] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [87.482406] [IGT] kms_rotation_crc: exiting, ret=0 <6> [87.496672] Console: switching to colour frame buffer device 180x56 <7> [87.513474] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.514006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.514542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.514967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.515465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.547452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.547900] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.548280] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<6> [76.684230] Console: switching to colour dummy device 80x25

<6> [76.684291] [IGT] kms_rotation_crc: executing

<7> [76.689734] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [76.689745] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [76.689916] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [76.690028] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [76.690303] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [76.690306] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [76.690445] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [76.690550] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [76.690877] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [76.690882] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [76.691023] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [76.691127] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<7> [76.691468] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]

<7> [76.691472] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]

<7> [76.691945] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00

<7> [76.692266] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000

<7> [76.692381] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [76.692492] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [76.692626] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz

<5> [76.692631] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [76.692634] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [76.692635] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00

<7> [76.692637] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<5> [76.692640] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [76.692641] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor

<5> [76.692644] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [76.692645] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0

<5> [76.692647] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [76.692660] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes

<7> [76.692807] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [76.693108] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<5> [76.693936] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [76.693943] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [76.693945] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [76.694007] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:

<7> [76.694010] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [76.694015] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [76.694029] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [76.694033] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [76.694196] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [76.694207] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [76.694210] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [76.694351] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [76.694362] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [76.694365] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [76.694507] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<6> [76.694668] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top

<7> [76.696534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0

<7> [76.696638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [76.696726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [76.696803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [76.696875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [76.696970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [76.697076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [76.697176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [76.697274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [76.697371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [76.697467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [76.697829] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [76.697944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [76.698081] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<7> [76.732227] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [76.733104] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [76.733906] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [76.734369] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [76.734788] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [76.735210] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation

<7> [76.735528] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [76.735963] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [76.736437] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [76.736846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [76.737201] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [76.737541] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [76.737911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [76.738241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [76.738540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [76.738869] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [76.739202] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [76.739494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [76.739781] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [76.740037] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [76.740291] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [76.740544] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [76.740806] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8

<7> [76.741046] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [76.741271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [76.741535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [76.741920] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [76.742123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [76.742322] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [76.742508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [76.742692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [76.742911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [76.743086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [76.743272] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [76.743471] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [76.743640] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [76.743921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [76.744079] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [76.744229] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [76.744378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [76.744545] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [76.744689] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [76.744858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [76.744993] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [76.745128] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [76.745260] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [76.745387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [76.745513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [76.745637] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [76.745775] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [76.745896] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [76.746015] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [76.746149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [76.746269] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [76.746387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [76.746503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.746616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.746733] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.746862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [76.746987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [76.747100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.747214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.747326] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [76.747425] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [76.747522] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [76.764608] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [76.764806] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [76.767252] xe 0000:00:02.0: [drm:intel_dp_dump_link_status [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] ln0_1:0x77 ln2_3:0x77 align:0x80 sink:0x1 adj_req0_1:0x0 adj_req2_3:0x0

<7> [76.767474] xe 0000:00:02.0: [drm:intel_dp_link_ok [xe]] [ENCODER:390:DDI A/PHY A] 8b/10b link not ok, retraining

<7> [76.784792] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [76.785293] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [76.785669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [76.818210] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]

<7> [76.819461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [76.819888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [76.820197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.820486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.820816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.821123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.821408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.821664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.821991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.822240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.822564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [76.823209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [76.823463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [76.823723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.823963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.824223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.824460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.824690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.825014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.825273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.825508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.825785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [76.826359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [76.826580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [76.826880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.827091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.827290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.827476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.827660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.827906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.828080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.828248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.828424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [76.828723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [76.829005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [76.829268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [76.829563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [76.830122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [76.831105] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [76.831340] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [76.832013] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [76.832200] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [76.847724] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1

<7> [76.850674] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]

<7> [76.881832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [76.882389] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [76.882942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [76.883765] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]

<7> [76.884564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [76.885021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [76.885328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.885681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [76.886098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [76.886437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [76.886821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [76.887279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [76.887761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [76.888221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [76.888665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [76.889193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [76.889671] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz

<7> [76.890583] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [76.890986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [76.915770] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [76.916297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [76.916700] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]

<7> [76.916782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [76.917478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [76.917916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [76.918244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.918533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [76.918870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [76.919151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [76.919456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [76.919890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [76.920281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [76.920666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [76.921108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [76.921505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [76.923028] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [76.923401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [76.948745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [76.948940] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]

<7> [76.949096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [76.949394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [76.949644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [76.949951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [76.950173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [76.950381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [76.950583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [76.950849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [76.951087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [76.951375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [76.951641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [76.951952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [76.952278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [76.952551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [76.953916] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [76.954214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [76.981849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [76.982333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [76.982822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [76.983547] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]

<7> [77.005486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [77.005887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [77.006206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.006490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.006980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.007231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.007566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.007938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.008251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.008567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.009050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.009314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.010059] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.010312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.031695] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]

<7> [77.031780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.032235] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.032675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.057606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [77.057757] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [77.057853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.057936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.058016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.058083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.058160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.058255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.058345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.058430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.058514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.058594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.059050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.059150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.081756] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]

<7> [77.082450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [77.082828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [77.082963] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.083085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.083362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.083376] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.083592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.083766] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.083876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.084183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.084548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.084938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.085267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.085584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.085916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.086659] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.086988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.099221] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437]

<7> [77.131833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.132434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.132725] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]

<7> [77.132939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.134153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [77.134504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [77.134876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.135180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.135473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.135863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.136188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.136602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.137049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.137499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.137982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.138388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.139357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.139803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.164868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.165404] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.165896] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.166115] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]

<7> [77.166900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [77.167255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [77.167567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.167917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.168199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.168483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.168817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.169219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.169610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.170099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.170527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.170978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.171993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.172394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.198882] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]

<7> [77.198850] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.199344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.199648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [77.199809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.200070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [77.200382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.200678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.201036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.201367] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.201688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.202165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.202557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.202981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.203387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.203772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.205125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.205524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.231861] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.232309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.232682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.232988] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441]

<7> [77.250249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [77.250580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [77.250946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.251234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.251516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.252038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.252387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.252872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.253298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.253685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.254137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.254513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.255685] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.256149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.282302] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442]

<7> [77.282815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.283396] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.283903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.306632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [77.306881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [77.306998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.307106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.307207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.307303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.307416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.307576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.307739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.307865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.307984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.308102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.308545] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.308673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.331394] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [77.331781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [77.331891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.332088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.332378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.332381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.332675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.332846] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.333023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.333285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.333538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.333880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.334105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.334541] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [77.334796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [77.335000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.335196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.335394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.335586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.335811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.335985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.336162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.336334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.336967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.337242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.381457] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.382001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.381935] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.382347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.382477] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.382664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.383059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.383019] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.383394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.383780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.384420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.384743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.385025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.385272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.385518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.385868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.386157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.386542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.386965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.387371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.387761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.388189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.389147] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.389550] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.415139] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443]

<7> [77.414923] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.415415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.415882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.416142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [77.416484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [77.416844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.417135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.417415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.417762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.418071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.418643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [77.418991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [77.419226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.419507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.419751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.419981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.420207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.420671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [77.420964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [77.421151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.421344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.421522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.421695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.421936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.422209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.422464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.422786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.423019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.423250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.423903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.424125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.447975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.448254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.448488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.448761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.448879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.448999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.449258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.449292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.449514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.449649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.450053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.450301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.450536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.450850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.451082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.451350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.451567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.452047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.452247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.452473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.452671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.452951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.453124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.453299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.453568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.453863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.454114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.454369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.454593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.455340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.455570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.481611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [77.482012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [77.482159] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.482293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.482553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.482607] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.482873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.483096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.483177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.483515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.483932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.484297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.484648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.485040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.485389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.486403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.486807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.514664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [77.515108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [77.515214] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.515413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.515697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.515703] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.516139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.516207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.516429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.516755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.517161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.517552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.518043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.518479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.518953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.520174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.520574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.547989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [77.548286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [77.548542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.548852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.548993] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.549104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.549363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.549437] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.549636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.549860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.550042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.550405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.550773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.551186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.551558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.552463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.552847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.581258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.581578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.581926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.582043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.582188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.582441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.582487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.582762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.582930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.583065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.583433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.583812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.584163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.584555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.585001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.585881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.586246] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.614663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [77.615056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [77.615173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.615336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.615620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.615618] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.615954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.616103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.616228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.616553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.616998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.617389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.617797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.618229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.618649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.619946] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.620349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.647908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [77.648184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [77.648415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.648632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.648923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.649058] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.649148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.649444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.649463] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.649842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.649880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.650199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.650545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.650933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.651326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.652434] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.652804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.681507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [77.681868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [77.681898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.682124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.682362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.682318] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.682591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.682672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.682915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.683197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.683564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.683988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.684391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.684767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.685104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.686065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.686430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.711812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.712231] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.712582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.713045] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [77.713029] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [77.713030] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [77.714612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [77.714993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [77.715256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.715504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.715778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.716041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.716343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [77.716762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [77.717121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [77.717470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.717880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [77.718221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [77.719292] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.719654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.748829] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444]

<7> [77.748768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.749261] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.749651] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.750400] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.750812] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [77.751112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [77.751378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [77.751632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.751947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.752250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.752492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.752836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.753079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [77.753308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [77.753535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [77.753794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.754014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.754233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.754448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.754702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.755169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [77.755551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [77.755943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.756337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.756675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [77.757830] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.758162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.764198] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [77.783196] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445]

<7> [77.784885] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.814529] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.814950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [77.815037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.815314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [77.815528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.815604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [77.815954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.816006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.816295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.816570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.816924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.817227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [77.817625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [77.818090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [77.818528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.818963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.819353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [77.820366] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.820794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.848041] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.848435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [77.848803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [77.848832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.849077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [77.849278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.849334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.849608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.849661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.849899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.850185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.850458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.850831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [77.851183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [77.851583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.851961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.852319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [77.853576] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.853987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.881162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.881500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [77.881831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [77.881829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.882077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [77.882241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.882307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.882530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.882592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.882797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.883034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.883350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [77.883911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.884225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [77.884475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [77.884734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [77.884951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.885165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.885381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.885589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.885858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [77.886215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [77.886623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [77.887053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.887424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.887803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [77.888897] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.889260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.914863] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.914867] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.915188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [77.915248] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.915428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [77.915578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.915660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [77.915958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.916234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.916468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.916758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.917045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.917573] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.917938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [77.918196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [77.918440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [77.918682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.918999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.919238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.919473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.919697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.920154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [77.920495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [77.920829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.921141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.921425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [77.922227] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.922520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.948103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.948577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [77.949037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [77.949178] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.949358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [77.949665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.949763] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.950053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.950234] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.950349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.950636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.951051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [77.951682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.952076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [77.952329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [77.952573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [77.952855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.953075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.953294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.953544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.953823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [77.954149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [77.954455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [77.954822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.955109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [77.955374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [77.956136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.956406] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.981168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.981493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [77.981862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [77.981997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.982108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [77.982339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.982408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.982593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.982861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.982802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.983094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.983391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.984094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [77.984408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [77.984660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [77.984983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [77.985228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.985494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.985733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.985959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.986179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [77.986498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [77.986905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [77.987221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.987515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [77.987830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [77.988555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.988852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.997989] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.031129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.031484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.031827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.031952] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.032070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.032304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.032364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.032546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.032756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.032820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.033073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.033411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.033799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.034187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.034572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.035053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.035449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.036438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.036864] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.064544] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.064945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [78.064991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.065204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [78.065442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [78.065400] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.065668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.065795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.066055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.066299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.066583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.066922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.067283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.067635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.068044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.068385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.068746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.070014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.070375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.097902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.098289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.098620] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.098976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.099132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.099255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.099522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.099621] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.099811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.100072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.100078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.100377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.100771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.101126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.101473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.101871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.102210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.103285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.103642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.131372] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.131772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [78.131892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.132076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [78.132336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [78.132334] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.132586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.132765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.132926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.133169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.133442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.133724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.134087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.134441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.134805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.135200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.135562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.136544] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.136943] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.164465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.164866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [78.164957] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.165174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [78.165409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [78.165369] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.165635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.165776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.166013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.166259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.166519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.166824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.167190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.167543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.167927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.168323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.168696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.169778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.170133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.198761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.199365] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446]

<7> [78.199210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.199591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.201806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.202187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [78.202471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [78.202775] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [78.203036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.203331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.203579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.203876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.204139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.204374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.204605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.204885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.205164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.205414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.205640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.205920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.206161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.206495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.206848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.207229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.207543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.207987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.208971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.209283] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.215624] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447]

<7> [78.216558] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.247780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.248121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [78.248382] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [78.248626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [78.248963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.248984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.249232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.249427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.249482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.249811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.249844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.250093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.250459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.250854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.251211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.251560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.251949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.252916] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.253303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.281129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.281392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [78.281560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [78.281747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [78.281761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.281893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.282030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.282005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.282162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.282211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.282309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.282457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.282635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.282843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.283107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.283363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.283614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.284428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.284613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.314435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.314730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [78.314882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [78.315020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [78.315153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.315281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.315407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.315550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.315735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.315762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.315969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.315993] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.316167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.316222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.316358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.316546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.316737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.317792] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.318133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.348090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.348451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [78.348772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [78.348794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.349035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [78.349203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.349291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.349503] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.349542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.349850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.350093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.350415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.350795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.351112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.351423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.351738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.352077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.352929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.353211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.381229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.381792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [78.381893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.382115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [78.382406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [78.382391] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.382681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.382862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.383027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.383290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.383587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.383939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.384507] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.384862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [78.385114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [78.385356] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [78.385592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.385896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.386192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.386439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.386681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.387125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.387508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.387961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.388331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.388729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.389714] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.390030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.414577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.415064] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [78.415035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.415376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [78.415482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.415664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [78.415939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.416052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.416402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.416711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.416967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.417257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.417881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.418257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [78.418585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [78.419000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [78.419248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.419483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.419718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.419931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.420160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.420500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.420844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.421160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.421504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.421852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.422637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.422956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.431142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.464410] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.464822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [78.464911] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.465181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [78.465470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [78.465405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.465804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.465875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.466105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.466350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.466599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.466924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.467549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.467876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [78.468127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [78.468354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [78.468578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.468875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.469136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.469363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.469603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.470000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.470378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.470733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.471074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.471408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.472304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.472662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.497911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.498301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [78.498587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [78.498924] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [78.499053] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.499183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.499428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.499498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.499670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.499942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.500023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.500289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.500898] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.501188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [78.501416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [78.501636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [78.501925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.502176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.502393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.502604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.502884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.503262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.503573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.503893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.504228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.504501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.505480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.505749] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.531087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.531424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [78.531670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [78.531993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [78.532023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.532224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.532372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.532447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.532737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.532708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.532987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.533278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.533638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.534108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.534458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.534783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.535093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.535949] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.536240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.564621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.565039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [78.565095] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.565349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [78.565507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.565588] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [78.565885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.565922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.566132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.566399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.566666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.567074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [78.567438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.567816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.568164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.568562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.568992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.569985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.570347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.597760] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.598149] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [78.598426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [78.598722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [78.598883] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.599000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.599263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.599371] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.599525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.599866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.599827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.600131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [78.600491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [78.600910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [78.601346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.601739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [78.602106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [78.603084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.603447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.631174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [78.631500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [78.631855] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [78.631995] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.632141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.632412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.632483] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.632701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.632942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.632996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.633258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [78.633484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [78.633738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [78.633961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [78.634183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.634403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.634624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.634930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.635178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.635530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.635977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.636334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.636672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.637123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.638198] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.638592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.639510] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [78.639836] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [78.664506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.664869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.664878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.665124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.665227] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.665359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.665541] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.665586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.665909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.666168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.666488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.666864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.667189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.667504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.667865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.668647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.669018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.698767] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448]

<7> [78.698840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.699296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.699732] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [78.699722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.700019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [78.700289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.700603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.701011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.701265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.701551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.701988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.702395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.702785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.703194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.703552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.704629] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.705077] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.731124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.731476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.731853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.731953] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.732138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.732411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.732438] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.732758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.732903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.733032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.733392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.733768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.734174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.734514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.734942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.735957] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.736318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.764788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [78.764849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.765138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [78.765334] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.765443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.765767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.765789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.766045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.766366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.766699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.767103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.767499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.767932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.768363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.768762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.769878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.770273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.797752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [78.798048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [78.798300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.798538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.798868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.798978] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.799134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.799405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.799426] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.799788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.799852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.800148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.800498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.800937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.801329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.802327] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.802700] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.831055] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [78.831327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [78.831559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.831847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.831971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.832080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.832311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.832384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.832559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.832778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.832963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.833321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.833694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.834090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.834429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.835284] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.835644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.864824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.865254] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.865622] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.867774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.868070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.868321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.868556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.868902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.869134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.869467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.869865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.870210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.870583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.870952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.871284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.872213] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.872556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.897859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [78.898194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [78.898468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.898800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.898945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.899060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.899331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.899393] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.899607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.899819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.900200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [78.900465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [78.900723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.900952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.901222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.901449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.901710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.902063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.902411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.902837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.903228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.903592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.904591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.904998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.931183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.931502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.931867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.931984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.932154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.932430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.932477] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.932793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.932955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.933115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.933707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.933948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.934179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.934452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.934703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.934998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.935248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.935633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.936078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.936437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.936801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.937166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.938104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.938390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.964612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [78.965039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [78.965098] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.965316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.965555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.965511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.965857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.965932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.966125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.966441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.967000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [78.967242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [78.967473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.967727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.967957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.968195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.968432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.968965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [78.969190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [78.969453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.969703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.969952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.970164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.970385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.970757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.971113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.971454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.971789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.972092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.972965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.973258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.997706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [78.997977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [78.998208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.998426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.998637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.999008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.999082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.999235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.999436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.999643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [78.999771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.999907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.000104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.000296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.000486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.000746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.000956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.001426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [79.001674] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.001884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.002104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.002283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.002461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.002718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.003021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.003306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.003574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.003864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.004106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.004846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.005086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.031124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [79.031444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [79.031807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.031887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.032203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.032294] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.032483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.032744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.032834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.033097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.033353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.033601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.033930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.034809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.035140] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.081324] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.081793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.081921] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.082096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.082374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.082420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.082643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.082915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.083031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.083375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.083830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.084221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.084597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.085106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.085489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.086591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.087038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.114716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.115256] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.115746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.116699] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449]

<7> [79.117599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [79.118015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [79.118324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.118697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.118985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.119304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.119614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.120182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.120617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.121098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.121481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.121877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.122913] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.123311] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.147755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.148143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.148444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.148790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.148877] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.149045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.149337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.149321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.149631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.149752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.150100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.150491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.150972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.151349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.151736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.152736] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.153099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.181352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [79.181645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [79.182033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.182063] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.182295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.182547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.182536] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.182926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.183004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.183241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.183670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.184066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.184452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.184920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.185303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.186325] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.186747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.214351] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [79.214750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [79.214894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.215053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.215337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.215380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.215612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.215872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.216002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.216345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.216827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.217277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.217747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.218128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.218547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.219634] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.220091] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.247830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [79.248178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [79.248483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.248834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.248870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.249119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.249360] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.249446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.249822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.249823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.250228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.250621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.251126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.251505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.251915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.252905] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.253313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.281018] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.281272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.281457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.281622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.281857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.281875] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.282011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.282162] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.282202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.282404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.282416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.282623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.282917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.283238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.283551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.284534] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.284920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.314173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [79.314303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [79.314360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.314418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.314475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.314536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.314615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.314729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.314818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.314882] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.314915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.315017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.315040] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.315118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.315165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.315546] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.315683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.347406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.347487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.347544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.347601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.347670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.347727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.347807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.347928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.348034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.348134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.348219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.348303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.348671] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.348852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.348975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.349106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.349191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.376017] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off

<7> [79.376133] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [79.380862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [79.380947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [79.381004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.381059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.381114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.381169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.381240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.381329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.381414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.381492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.381570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.381667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.381680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.381852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.381979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.382094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.382409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.414102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [79.414218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [79.414304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.414384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.414456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.414519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.414598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.414746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.414755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.414871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.414932] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.414979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.415054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.415085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.415189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.415581] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.415709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.447666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.447849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.447972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.461530] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450]

<7> [79.462263] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.462417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [79.462507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [79.462590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [79.462696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.462775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.462853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.462929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.463010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.463093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [79.463177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [79.463252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [79.463323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.463393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.463462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.463531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.463617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.463822] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.463921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [79.463995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [79.464062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [79.464127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.464193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.464259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.464324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.464390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.464455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [79.464518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [79.464582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [79.464653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.464724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.464786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.464847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.464913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.465019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.465126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.465230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.465337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.465441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.466032] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.466149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.480571] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [79.498626] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451]

<7> [79.499233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.530786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.530925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.530999] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.531066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.531131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.531193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.531255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.531315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.531390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.531526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.531652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.531664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.531739] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.531822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.531844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.531896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.531967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.531972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.532039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.532114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.532188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.532297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.532404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.532497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.532583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.532701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.533283] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.533531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.564232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.564420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [79.564506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [79.564579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [79.564672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.564662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.564744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.564794] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.564817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.564894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.564917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.565009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.565277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.565384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [79.565460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [79.565535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [79.565604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.565684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.565761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.565830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.565904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.566024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.566135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.566245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.566358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.566473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.567090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.567229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.597565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.597806] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.597846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.597950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.597978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.598047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.598140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.598126] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.598233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.598329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.598424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.598546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.598880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.599020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.599124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.599224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.599323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.599422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.599525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.599664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.599785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.599964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.600139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.600316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.600495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.600770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.601656] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.601878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.631201] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.631478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [79.631715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [79.631714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.631889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [79.631986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.632053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.632218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.632236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.632383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.632545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.632764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.633048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.633320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.633588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.633859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.634108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.634985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.635265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.664187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.664459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [79.664708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [79.664688] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.664894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [79.664969] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.665072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.665250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.665227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.665428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.665601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.665819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.666101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.666374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.666663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.666932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.667201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.668131] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.668422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.697673] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.697856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.698044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.698276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [79.698348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.698544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [79.698790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [79.699008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.699224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.699437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.699680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.699951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.700326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.700704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.701023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.701337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.701668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.703215] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.703563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.714712] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.747725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.747666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.748071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.748066] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.748296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.748384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.748499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.748720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.748919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.749114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.749308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.749554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.749922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.750250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.750561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.750864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.751153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.752214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.752516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.781044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.781422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [79.781704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [79.781707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.781920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [79.782022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.782124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.782318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.782306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.782510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.782719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.782934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.783249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.783550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.783866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.784162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.784455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.785560] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.785898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.814211] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.814506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [79.814761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [79.814757] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.814969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [79.815064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.815163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.815354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.815343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.815547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.815769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.815986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.816291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.816585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.816893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.817182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.817467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.818459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.818785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.847650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.847956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.847989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.848274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [79.848289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.848506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [79.848740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [79.848952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.849163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.849369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.849575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.849837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [79.850168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [79.850488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [79.850895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.851207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [79.851516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [79.852551] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.852900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.880883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.881200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [79.881410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [79.881598] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [79.881829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.881833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.882018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.882105] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.882196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.882373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.882355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.882583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [79.882911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [79.883208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.883496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.883814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.884102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.885125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.885432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.914661] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.914963] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.915218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.919576] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452]

<7> [79.922087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.922476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [79.922724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [79.922920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [79.923102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.923280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.923458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.923655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.923839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.924014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.924189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.924357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.924518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.924695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.924859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.925018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.925222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.925490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.925750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.925988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.926212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.926435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.927570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.927802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.933215] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453]

<7> [79.934642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.964337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.964747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.964799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.965053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.965092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.965282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.965404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.965500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.965742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.965962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.966181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.966451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.967027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.967308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.967525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.967816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.968028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.968236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.968444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.968680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.968905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.969261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.969635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.969955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.970269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.970582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.971533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.971879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.997650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.997840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.997966] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.998129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [79.998193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.998315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [79.998479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [79.998877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.999045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.999203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.999357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.999673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.000090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.000286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [80.000434] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [80.000577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [80.000740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.000886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.001023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.001157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.001297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.001514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.001745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.001949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.002144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.002330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.003194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.003392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.031000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.031314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.031526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.031767] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.031772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.031966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.032065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.032161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.032354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.032339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.032544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.032791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.033279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.033534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.033757] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.033948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.034136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.034322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.034510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.034715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.034919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.035243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.035560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.035885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.036189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.036483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.037528] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.037865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.064449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.064745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.064814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [80.065012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [80.065032] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.065196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [80.065290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.065374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.065550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.065759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.065940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.066156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.066744] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.066985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [80.067175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [80.067350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [80.067524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.067721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.067902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.068078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.068267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.068563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.068876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.069167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.069458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.069755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.070702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.071004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.097522] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.097830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.097874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [80.098079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [80.098141] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.098264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [80.098445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.098410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.098668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.098854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.099035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.099250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.099891] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.100120] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [80.100291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [80.100456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [80.100647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.100816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.100979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.101142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.101317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.101614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.101894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.102167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.102436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.102723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.103647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.103935] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.130927] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.131235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [80.131430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [80.131653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [80.131659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.131840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.131947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.132018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.132196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.132211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.132371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.132589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.132918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.133216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.133503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.133810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.134096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.135385] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.135721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.147949] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.180938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.181302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.181544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.181813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.181818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.182032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.182176] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.182246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.182459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.182508] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.182690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.182928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.183267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.183585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.183914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.184227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.184533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.185524] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.185873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.214250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.214654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [80.214648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.214885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [80.214970] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.215095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [80.215294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.215259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.215490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.215728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.215928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.216160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.216495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.216846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.217163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.217477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.217790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.218801] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.219106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.247469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.247746] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.247781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.247975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.248024] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.248157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.248280] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.248334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.248511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.248705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.248884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.249100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.249407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.249722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.250015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.250305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.250619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.251548] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.251867] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.281137] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.281440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [80.281688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [80.281695] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.281890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [80.281988] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.282083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.282273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.282263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.282465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.282665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.282875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.283180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.283472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.283791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.284080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.284366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.285402] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.285725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.314113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.314418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [80.314675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [80.314665] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.314864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [80.314940] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.315047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.315226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.315195] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.315406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.315583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.315793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.316081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.316359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.316646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.316916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.317183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.318074] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.318358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.347617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.347668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [80.347879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [80.347906] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.348068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [80.348156] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.348249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.348427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.348672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.348860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.349038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [80.349217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [80.349394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [80.349570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [80.349769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.349948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.350125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.350300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.350512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.350821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.351098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.351369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.351659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.351929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.352906] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.353191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.354073] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [80.354310] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [80.380863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.381113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.381319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.381517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.381758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.381859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.382056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.382058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.382286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.382330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.382642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.382946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.383235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.383521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.383831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.384745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.385044] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.414632] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.414946] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.415224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.415869] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454]

<7> [80.433888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [80.434165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [80.434318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.434449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.434573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.434731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.434893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.435093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.435274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.435447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.435815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.435978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.436623] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.436788] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.464236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.464518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.464803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.464811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.465029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.465157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.465244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.465456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.465470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.465726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.466092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.466440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.466892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.467244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.467606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.468821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.469176] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.497914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [80.498187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [80.498411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.498677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.498686] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.498881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.498984] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.499076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.499262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.499308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.499833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [80.500046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [80.500241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.500430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.500648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.500842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.501047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.501373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.501710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.502033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.502346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.502678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.504360] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.504719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.530940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [80.531197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [80.531397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.531644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.531695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.531888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.531947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.532080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.532226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.532320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.532838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [80.533046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [80.533239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.533428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.533641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.533819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.534008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.534308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.534636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.534928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.535212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.535497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.536607] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.536913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.564232] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [80.564503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [80.564776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.564777] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.564996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.565095] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.565211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.565426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.565396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.565694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.566240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [80.566463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [80.566699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.566909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.567117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.567324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.567551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.568081] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [80.568284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [80.568472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.568684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.568878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.569069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.569271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.569609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.569924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.570239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.570549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.570874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.571773] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.572076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.597662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.597619] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.597907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.598018] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.598108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.598301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.598345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.598495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.598701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.598945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.599465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.599692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.599889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.600078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.600270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.600460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.600693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.601148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.601333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.601508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.601702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.601881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.602054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.602240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.602538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.602846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.603140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.603416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.603697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.604612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.604883] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.630986] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [80.631282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [80.631505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.631772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.631777] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.631988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.632115] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.632196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.632429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.632449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.632809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.633132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.633446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.633780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.634096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.635172] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.635511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.664201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [80.664471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [80.664741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.664744] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.664959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.665067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.665171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.665379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.665373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.665668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.666027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.666372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.666731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.667068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.667401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.668723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.669050] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.697604] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.697813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [80.697918] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.698042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [80.698198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.698243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.698436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.698653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.698847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.699073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [80.699403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [80.699747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [80.700064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.700376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [80.700709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [80.701718] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.702041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.730821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [80.731088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [80.731297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.731496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.731750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.731743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.731946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.732042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.732177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.732322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.732510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.732852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.733170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.733484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.733821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.734984] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.735314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.764330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [80.764730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [80.764734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.764971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.765081] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.765193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.765409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.765398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.765651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.765864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.766080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.766292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.766499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.767736] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.768095] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.814171] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [80.814440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [80.814710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.814711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.814918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.815017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.815113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.815304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.815295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.815537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.816427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.816784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.817107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.817424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.817764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.818761] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.819102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.847616] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.848056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.848436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.849789] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455]

<7> [80.878449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [80.878683] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [80.878766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.878839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.878908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.878975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.879075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.879197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.879309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.879418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.879527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.879664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.880267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.880436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.914247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [80.914623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [80.914632] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.914876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.915111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.915096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.915343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.915485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.915627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.915919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.916324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.916740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.917122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.917498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.917895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.919171] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.919526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.947606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.947848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [80.947960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.948152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [80.948251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.948388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.948627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.948835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.949035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.949285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.949655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.949989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.950308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.950649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.950966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.952144] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.952475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.980752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [80.981002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [80.981208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.981405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.981654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.981651] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.981851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.981951] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.982098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.982233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.982433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.982793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.983090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.983380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.983690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.984704] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.985010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.014110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [81.014347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [81.014549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.014785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.014787] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.014989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.015083] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.015184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.015358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.015414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.015761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.016084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.016398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.016734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.017052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.017964] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.018288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.047415] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.047583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.047707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.047916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.047881] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.048115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.048161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.048311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.048504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.048761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.049098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.049419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.049736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.050024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.050308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.051141] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.051450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.080811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [81.081047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [81.081247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.081443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.081671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.081681] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.081870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.081976] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.082100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.082252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.082606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [81.082810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [81.082995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.083183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.083372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.083584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.083774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.084073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.084346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.084631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.084893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.085139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.085909] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.086149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.113838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.113951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.114019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.114085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.114151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.114216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.114296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.114467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.114540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.114636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.114638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.114717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.114760] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.114784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.114849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.114859] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.114920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.115034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.115145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.115256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.115366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.115474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.115888] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.116036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.147586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.147698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.147884] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.147935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.148129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.148137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.148312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.148492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.148685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.148919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.149381] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.149595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.149781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.149954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.150128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.150302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.150487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.151031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.151221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.151397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.151593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.151769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.151942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.152126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.152425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.152743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.153038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.153329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.153644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.154523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.154829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.180668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [81.180877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [81.181046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.181211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.181374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.181535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.181745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.181780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.182006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.182213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [81.182241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.182384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [81.182567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.182739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.182900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.183063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.183237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.183674] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [81.183849] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [81.184009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.184169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.184330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.184492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.184777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.185064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.185335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.185622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.185889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.186154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.187022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.187274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.214589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.214945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.215201] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456]

<7> [81.215235] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.237481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.237776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [81.237890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [81.237985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [81.238073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.238159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.238242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [81.238322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [81.238402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.238480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.238584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [81.238663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [81.238741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.238817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.238892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.238965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.239065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.239327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.239422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [81.239494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [81.239577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [81.239645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.239714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.239781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [81.239847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [81.239912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.239977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.240041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [81.240106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [81.240172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.240239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.240304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.240368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.240441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.240569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.240682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.240794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.240902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.241009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.241974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.242123] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.246921] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [81.265496] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457]

<7> [81.281576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.281901] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.282054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.284753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.285351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.285486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.314139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.314581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.314605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [81.314876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [81.314935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.315131] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [81.315275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.315377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.315627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.315868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.316100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.316396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.316822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.317185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.317534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.317938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.318281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.319416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.319804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.347441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.347761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.347810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [81.348024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [81.348068] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.348222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [81.348346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.348417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.348643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.348845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.349039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.349274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.349631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.349950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.350264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.350594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.350907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.352107] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.352441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.380697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.381033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [81.381266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [81.381480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [81.381760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.381739] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.381957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.382044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.382149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.382340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.382324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.382594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.382926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.383243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.383576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.383892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.384200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.385263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.385613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.414222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.414509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [81.414751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [81.414753] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.414939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [81.415029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.415117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.415292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.415284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.415470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.415670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.415883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.416187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.416481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.416803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.417095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.417383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.418336] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.418655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.447291] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.447591] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.447635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [81.447844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [81.447889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.448038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [81.448162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.448231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.448422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.448637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.448832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.449061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.449389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.449720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.450034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.450343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.450689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.451689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.451992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.480750] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.481048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [81.481247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [81.481430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [81.481651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.481655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.481838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.481927] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.482020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.482198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.482177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.482414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.482746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.483042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.483332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.483643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.483931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.485164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.485456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.498117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.530784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.531293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [81.531635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [81.531655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.531895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [81.532141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.532124] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.532379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.532524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.532671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.532906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.533195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.533633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.534027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.534414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.534814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.535190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.536298] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.536663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.564075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.564401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [81.564690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [81.564684] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.564914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [81.565028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.565124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.565332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.565351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.565602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.565814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.566066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.566425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.566780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.567095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.567405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.567730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.568809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.569134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.597272] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.597609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [81.597575] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.597821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [81.597885] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.598019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [81.598170] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.598212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.598403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.598624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.598818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.599045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.599377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.599717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.600007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.600290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.600622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.601609] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.601907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.630886] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.631169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [81.631365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [81.631586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [81.631598] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.631768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.631873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.631948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.632125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.632130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.632300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.632509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.632998] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.633233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [81.633414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [81.633609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [81.633771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.633932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.634096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.634258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.634433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [81.634733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [81.635006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [81.635276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.635558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [81.635825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [81.636759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.637038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.663989] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.664299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [81.664506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [81.664746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [81.664757] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.664945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.665055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.665135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.665327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.665333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.665518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.665798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.666282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.666551] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [81.666751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [81.666943] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [81.667132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.667321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.667511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.667718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.667911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [81.668206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [81.668498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [81.668803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.669091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [81.669384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [81.670557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.670866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.697585] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.697978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.698315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.701554] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458]

<7> [81.727541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.727786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [81.727872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [81.727945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [81.728015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.728084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.728152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.728218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.728284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.728350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.728415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.728481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.728571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.728639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.728706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.728772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.728868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.729068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.729162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [81.729234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [81.729300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [81.729366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.729432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.729497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.729578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.729646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.729711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.729779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.729846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.729912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.729977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.730042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.730108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.730178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.730292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.730403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.730512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.730633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.730746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.731438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.731679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.748815] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459]

<7> [81.764560] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.764845] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.765046] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.772172] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.772974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.773129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.797322] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.797562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.797749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [81.797863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.797995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [81.798145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.798213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [81.798424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.798653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.798863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.799060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.799311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.799971] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.800247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [81.800453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [81.800697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [81.800893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.801088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.801283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.801475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.801704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.802034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.802357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.802692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.803012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.803330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.804333] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.804664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.830673] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.830994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [81.831208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [81.831405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [81.831638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.831650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.831824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.832004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.831995] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.832182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.832289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.832395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.832724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.833034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.833326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.833637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.833930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.834963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.835272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.863937] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.864284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [81.864511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [81.864782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [81.864782] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.864995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.865100] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.865193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.865390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.865393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.865756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.866064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.866404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.866741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.867060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.867379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.867714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.868806] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.869133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.897577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.897561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.897883] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [81.897887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.898097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [81.898172] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.898295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [81.898487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.898698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.898894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.899086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.899315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.899673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.899999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.900316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.900643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.900932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.901962] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.902266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.930572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.930879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [81.931088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [81.931284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [81.931474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.931703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.931718] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.931899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.932016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.932091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.932293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.932317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.932692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.932989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.933281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.933591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.933881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.934844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.935151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.963980] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.964314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [81.964584] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [81.964586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.964792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [81.964885] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.964986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.965178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.965163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.965375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.965659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.965884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.966193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.966491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.966806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.967099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.967395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.968710] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.969028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.981045] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.013954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.014380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.014682] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.014689] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.014917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.015016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.015136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.015352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.015320] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.015589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.015807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.016068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.016438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.016821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.017169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.017536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.017856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.018863] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.019191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.047316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.047655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.047689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [82.047922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [82.047976] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.048140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [82.048274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.048352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.048589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.048803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.049012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.049262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.049632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.049957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.050272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.050618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.050930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.052030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.052359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.080586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.080918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.081135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.081333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.081565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.081576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.081755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.081855] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.081937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.082112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.082109] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.082336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.082697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.083003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.083296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.083603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.083890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.084887] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.085187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.114178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.114485] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [82.114739] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [82.114750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.114937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [82.115044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.115127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.115318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.115322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.115542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.115721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.115935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.116242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.116587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.116879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.117163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.117447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.118399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.118723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.147175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.147486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [82.147736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [82.147749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.147937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [82.148041] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.148130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.148323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.148315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.148534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.148728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.148958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.149291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.149653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.149944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.150230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.150534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.151494] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.151831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.180543] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.180696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026

<7> [82.180866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.180937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [82.181145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025

<7> [82.181141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.181342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.181551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.181749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.181942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.182133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [82.182323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.182535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.182724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.182914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.183106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.183296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.183485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.184007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.184563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026

<7> [82.184771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [82.184961] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025

<7> [82.185148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.185336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.185546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.185737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.185924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [82.186112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.186302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.186491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.186702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.186883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.187059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.187233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.187424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.187743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.188040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.188334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.188645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.188938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.189926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.190247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.191225] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [82.191465] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [82.230494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.230824] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.231043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.231246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.231444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.231700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.231693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.231937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.231990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.232263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.232444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.232670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.232863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.233052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.233245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.233438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.233662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.234149] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.234358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.234570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.234749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.234927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.235104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.235291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.235606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.235902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.236190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.236477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.236784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.237723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.238024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.263882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [82.264102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [82.264275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.264443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.264648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.264819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.264736] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.265016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.265096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.265381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.265443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [82.265648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [82.265818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.265986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.266149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.266310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.266485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.266923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [82.267095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [82.267258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.267421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.267609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.267774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.267949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.268222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.268492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.268780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.269048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.269318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.270229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.270492] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.297173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.297423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.297659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.297740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.297847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.298027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.298122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.298205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.298434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.298421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.298780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.299085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.299378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.299692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.299982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.301101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.301385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.330536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.330875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.330948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [82.331175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.331252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [82.331480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.331719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.331924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.332122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.332372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.332726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.333032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.333323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.333626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.333913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.334936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.335247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.363903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [82.364235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [82.364470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.364731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.364741] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.364943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.365049] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.365145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.365335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.365386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.365751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.366076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.366393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.366728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.367039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.368289] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.368658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.397263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [82.397573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [82.397573] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.397806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.397908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.398022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.398236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.398215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.398445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.398710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.399047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.399370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.399744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.400060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.400374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.401344] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.401691] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.447105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.447398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.447678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.447669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.447885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.447972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.448085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.448279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.448254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.448567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.448908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.449244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.449582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.449901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.450215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.451145] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.451477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.480529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.480591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [82.480821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [82.480847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.481024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.481124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.481220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.481411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.481632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.481852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.482158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.482455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.482761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.483048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.483336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.484344] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.484689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.513852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [82.514104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [82.514308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.514545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.514553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.514746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.514850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.514938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.515128] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.515171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.515519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.515839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.516152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.516460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.516794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.517994] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.518305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.547534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [82.547532] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.547801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [82.547873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.548023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.548175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.548238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.548449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.548676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.548929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.549286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.549689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.550009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.550318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.550656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.551687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.552012] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.580446] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [82.580708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [82.580716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.580913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.581008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.581108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.581302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.581284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.581516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.581757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.582087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.582407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.582740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.583052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.583360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.585105] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.585415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.613895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [82.614152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [82.614361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.614609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.614621] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.614812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.615008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.615017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.615204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.615397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.615355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.615626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.615820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.616667] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.616972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.663763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [82.663981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [82.664155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.664322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.664525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.664536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.664697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.664819] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.664902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.665074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.665187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.665464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.665752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.666024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.666288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.667122] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.667396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.697520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.697925] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.698256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.700390] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460]

<7> [82.701602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [82.701898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [82.702128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.702344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.702582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.702794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.703058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.703632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [82.703856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [82.704064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.704269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.704477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.704696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.704920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.705270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.705635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.705980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.706323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.706681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.707991] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.708328] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.730616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [82.730875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [82.731090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.731300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.731571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.731562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.731799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.731912] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.732055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.732233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.732721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [82.732951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [82.733157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.733363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.733596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.733805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.734024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.734376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.734739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.735080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.735421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.735769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.736998] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.737305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.764151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [82.764415] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [82.764670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.764678] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.764871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.764983] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.765067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.765257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.765263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.765505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.765997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [82.766199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [82.766388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.766596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.766790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.766981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.767185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.767744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [82.767947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [82.768136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.768324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.768527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.768720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.768925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.769242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.769603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.769925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.770236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.770563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.771517] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.771815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.797104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [82.797383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [82.797641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.797645] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.797854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.797947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.798054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.798248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.798227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.798512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.798991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [82.799186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [82.799364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.799555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.799734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.799912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.800102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.800548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [82.800740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [82.800916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.801090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.801268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.801444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.801646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.801952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.802242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.802527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.802798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.803054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.804051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.804300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.830547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [82.830819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [82.831041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.831254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.831466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.831741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.831725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.832047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.832264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.832355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.832640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.832996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.833338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.833726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.834040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.835008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.835330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.863778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [82.864023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [82.864227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.864421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.864667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.864662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.864865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.864960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.865094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.865236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.865427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.865769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.866085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.866400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.866733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.867651] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.867981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.897145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [82.897411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [82.897679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.897674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.897889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.897975] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.898087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.898281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.898247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.898531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.898869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.899195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.899532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.899828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.900117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.901124] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.901431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.930459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [82.930756] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [82.930761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.930984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.931078] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.931196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.931408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.931375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.931665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.931903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.932235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.932573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.932895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.933210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.933544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.934740] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.935061] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.964150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [82.964398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [82.964648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.964647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.964855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.964948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.965052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.965244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.965222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.965500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [82.965829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [82.966148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [82.966462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.966794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [82.967102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [82.968120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.968441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.997085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [82.997342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [82.997616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.997615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.997838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.997935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.998049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.998257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.998230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.998525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.998886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.999236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.999615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.999956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.000292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.001997] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.002330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.030502] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.030849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.031163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.032624] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461]

<7> [83.034549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.034944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [83.035176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [83.035379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [83.035620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.035827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.036022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.036215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.036406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.036661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [83.036867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [83.037057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [83.037248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.037437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.037648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.037841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.038081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.038424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.038767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.039088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.039403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.039731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.040817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.041121] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.046649] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [83.066024] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462]

<7> [83.067562] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.097129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.097578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.097635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.097905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.097928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.098154] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.098254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.098396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.098644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.098882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.099121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.099410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.099835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.100220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.100633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.101011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.101384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.102570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.102930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.130502] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.130657] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.130991] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.131091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [83.131362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [83.131350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.131635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [83.131860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.132076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.132292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.132515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.132792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.133168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.133538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.133889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.134236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.134594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.136314] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.136702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.163852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.164241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.164550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.164562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.164796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.165031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.165056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.165262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.165515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.165450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.165733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.165985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.166352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.166734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.167075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.167413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.167778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.168943] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.169295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.197337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.197698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [83.197649] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.197912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [83.198110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [83.198064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.198303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.198392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.198522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.198719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.198913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.199156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.199511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.199836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.200152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.200496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.200807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.201832] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.202155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.230432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.230880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [83.230781] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.231109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [83.231235] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.231322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [83.231556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.231606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.231768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.231977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.232182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.232430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.232986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.233264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [83.233501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [83.233709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [83.233914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.234118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.234324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.234577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.234786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.235109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.235427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.235765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.236076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.236383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.237452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.237794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.263899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.264235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [83.264506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [83.264522] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.264723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [83.264932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.264969] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.265139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.265348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.265328] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.265664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.265903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.266390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.266671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [83.266869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [83.267058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [83.267246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.267434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.267644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.267834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.268038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.268359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.268694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.269007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.269304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.269620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.270591] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.270862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.280681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.313722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.314094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.314343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.314643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.314626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.314868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.315081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.315070] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.315295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.315429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.315530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.315768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.316373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.316655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.316856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.317049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.317239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.317429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.317639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.317832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.318039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.318365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.318703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.319019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.319332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.319666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.320719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.321051] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.347086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.347408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [83.347678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [83.347675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.347878] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [83.348069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.348090] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.348261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.348473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.348421] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.348668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.348896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.349532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.349786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [83.349985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [83.350173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [83.350361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.350574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.350768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.350957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.351162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.351505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.351827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.352139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.352470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.352784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.354108] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.354391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.380353] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.380713] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.380676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.380928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.381127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.381084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.381320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.381414] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.381549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.381748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.381942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.382177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.382529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.382857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.383174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.383526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.383838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.384940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.385264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.414052] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.414367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [83.414627] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [83.414640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.414829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [83.415022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.415053] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.415217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.415412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.415378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.415647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.416407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.416776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.417098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.417411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.417738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.418044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.419120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.419447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.447027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.447372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [83.447678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [83.447666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.447901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [83.448115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.448117] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.448329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.448493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.448596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.448807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.449060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.449417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.449774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.450090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.450402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.450734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.451849] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.452185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.480507] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.480996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.481361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.482760] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463]

<7> [83.485279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.485736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [83.485983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [83.486193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [83.486397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.486630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.486837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.487032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.487226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.487418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.487633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.487827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.488018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.488206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.488395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.488611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.488872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.489191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.489502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.489781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.490045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.490301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.491309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.491578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.501673] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464]

<7> [83.502725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.530428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.530903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.530860] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.531185] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.531352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.531441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.531726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.531781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.531946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.532161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.532377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.532672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.533049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.533403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.533779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.534125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.534440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.535395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.535721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.563801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.564161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [83.564397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [83.564680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.564746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [83.564963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.565026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.565176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.565389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.565345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.565624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.565882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.566243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.566620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.566937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.567250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.567581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.569038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.569372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.596995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.597331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.597611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.597615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.597831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.597945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.598040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.598252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.598251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.598485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.598696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.598949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.599311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.599708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.600056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.600397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.600769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.601847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.602175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.630478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.630762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.630849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.631137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [83.631183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.631404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [83.631665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [83.631881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.632092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.632305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.632528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.632794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.633163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.633690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.634035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.634377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.634759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.635926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.636285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.663731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.664091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [83.664322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [83.664591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [83.664588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.664813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.664924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.665021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.665229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.665230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.665458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.665716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.666082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.666430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.666840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.667186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.667556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.668728] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.669058] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.697056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.697402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [83.697687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [83.697693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.697895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [83.697992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.698088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.698281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.698273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.698507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.698704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.698934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.699267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.699615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.699933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.700247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.700577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.701683] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.702022] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.714309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.747024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.747405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.747688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.747702] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.747907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.748105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.748118] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.748301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.748517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.748472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.748715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.748955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.749493] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.749760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.749962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.750156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.750344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.750560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.750755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.750945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.751147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.751499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.751831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.752149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.752489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.752806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.753828] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.754139] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.780569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.780484] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.780902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [83.780955] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.781134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [83.781349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [83.781318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.781613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.781832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.782044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.782252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.782613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.783164] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.783470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [83.783693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [83.783900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [83.784108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.784314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.784543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.784753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.784977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.785333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.785706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.786055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.786396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.786772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.788191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.788494] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.813664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.813997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.814224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.814482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.814492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.814698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.814844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.814895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.815085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.815145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.815275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.815522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.816129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.816383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [83.816617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [83.816810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [83.816997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.817184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.817373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.817584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.817788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.818113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.818429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.818758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.819071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.819379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.820400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.820724] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.847297] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.847659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.847701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [83.847945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [83.847998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.848165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [83.848308] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.848380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.848622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.848839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.849056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.849308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.849987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.850266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [83.850670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [83.850870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [83.851058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.851246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.851474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.851666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.851948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [83.852284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.852623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.852940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.853251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.853601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.854634] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.854939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.880483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.880520] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.880839] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.880894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [83.881146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [83.881151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.881373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [83.881635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.881853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.882063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.882270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.883300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [83.883658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [83.883960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [83.884232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.884508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [83.884781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [83.885812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.886071] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.913888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [83.914187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [83.914487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [83.914495] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.914730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.914847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.914961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.915192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.915179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.915421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.915696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [83.915924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [83.916151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [83.916378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [83.916626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.916855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.917079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.917303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.917596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.917993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.918378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.918785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.919163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.919585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.920821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.921182] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.922111] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [83.922367] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [83.947032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.947354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.947686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.947673] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.947942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.948028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.948180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.948359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.948410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.949130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.949564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.949921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.950266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.950624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.950939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.951931] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.952233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.980475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.980858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.981196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.985380] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465]

<7> [83.986668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [83.987013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [83.987266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.987539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.987781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.988013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.988305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.988732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.989119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.989501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.989841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.990183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.991370] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.991704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.013698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.013978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.014219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.014499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.014508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.014738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.014859] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.014967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.015191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.015242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.015650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.016040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.016415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.016822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.017161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.018317] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.018689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.047301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [84.047640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [84.047626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.047887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.047956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.048113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.048268] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.048331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.048574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.048843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.049209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.049604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.049949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.050288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.050646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.051702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.052033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.080298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [84.080606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [84.080610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.080830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.080929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.081044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.081256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.081227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.081492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.081749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.082114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.082499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.082834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.083146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.083508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.084588] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.084916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.113661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [84.113902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [84.114102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.114295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.114532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.114537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.114731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.114831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.114965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.115109] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.115297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.115633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.115947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.116253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.116582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.117471] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.117789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.146914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.147190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.147408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.147669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.147741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.147945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.147972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.148140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.148248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.148379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.148742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.149068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.149387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.149717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.150010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.150915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.151218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.180238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [84.180501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [84.180485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.180690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.180762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.180872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.181014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.181050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.181226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.181462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.181769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.182066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.182357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.182670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.182961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.183878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.184179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.213561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.213797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.213996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.214188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.214382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.214616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.214622] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.214858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.214915] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.215187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.215189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.215526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.215832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.216118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.216405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.217391] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.217717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.247138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [84.247364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [84.247599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.247600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.247786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.247873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.247966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.248143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.248124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.248966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.249480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [84.249667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [84.249833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.249994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.250157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.250319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.250520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.250800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.251073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.251342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.251623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.251889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.252771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.253055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.280239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [84.280479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [84.280481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.280669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.280754] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.280849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.281027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.281007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.281203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.281410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.281887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [84.282063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [84.282227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.282389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.282571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.282735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.282908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.283185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.283483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.283754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.284020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.284283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.285219] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.285523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.313534] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [84.313741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [84.313912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.314077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.314242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.314404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.314604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.314611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.314771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.314867] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.314935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.315096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.315099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.315455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [84.315621] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [84.315781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.315941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.316102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.316264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.316459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.316622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.316782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.316942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.317262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [84.317468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [84.317630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.317790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.317951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.318113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.318276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.318462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.318618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.318767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.319496] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.319756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.363507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.363741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.363922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.364092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.364259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.364453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.364462] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.364652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.364717] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.364951] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.365094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.365271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.365450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.365615] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.365779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.365940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.366112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.366549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.366721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.366883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.367045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.367208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.367369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.367583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.367860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.368131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.368396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.368680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.368948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.369745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.370013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.397467] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.397877] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.398183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.401529] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466]

<7> [84.402616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [84.402907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [84.403122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.403320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.403544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.403740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.403992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.404328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.404669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.404964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.405251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.405581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.406719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.407014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.430211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.430507] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.430609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.430831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.430850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.431044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.431165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.431256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.431507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.431763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.432120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.432490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.432833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.433169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.433526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.434650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.434979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.463852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [84.464127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [84.464340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.464599] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.464678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.464880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.464905] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.465073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.465185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.465308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.465672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.465999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.466319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.466656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.466971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.468002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.468333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.496819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [84.497071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [84.497274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.497546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.497521] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.497730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.497804] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.497908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.498063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.498121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.498439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.498737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.499027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.499313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.499619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.500578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.500876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.530179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [84.530450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [84.530441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.530641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.530718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.530832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.531026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.530995] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.531220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.531563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.531914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.532234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.532563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.532856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.533142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.533942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.534244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.563574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.563836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.564035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.564222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.564441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.564452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.564625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.564755] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.564842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.565026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.565152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.565465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.565760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.566049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.566338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.567218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.567560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.596892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [84.597141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [84.597346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.597588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.597659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.597856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.597896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.598048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.598174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.598278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.598631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.598964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.599279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.599615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.599932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.600974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.601300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.630139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [84.630380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [84.630625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.630631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.630826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.630930] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.631022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.631214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.631204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.631463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.631795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.632115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.632453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.632767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.633079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.634077] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.634399] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.664441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.664616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [84.664781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.664886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [84.665081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.665122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.665340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.665576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.665791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.666046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.666441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.666796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.667142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.667506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.667837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.668852] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.669181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.696834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [84.697111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [84.697331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.697596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.697600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.697814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.697919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.698023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.698217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.698267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [84.698654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.699009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.699355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.699721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.700060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.701169] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.701517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.730438] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.730781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.731084] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.736504] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467]

<7> [84.738551] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.738978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [84.739229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [84.739493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [84.739710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.739924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.740136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.740335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.740548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.740739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [84.740934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [84.741111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [84.741285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.741473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.741650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.741823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.742042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.742330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.742604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.742862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.743100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.743336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.744543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.744776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.746379] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [84.766634] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468]

<7> [84.769096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.796878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.797295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.797614] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.797624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.797874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.797973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.798125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.798311] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.798358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.798699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.798917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.799174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.799764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.800046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.800268] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.800502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.800711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.800917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.801126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.801334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.801574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.801938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.802289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.802657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.803007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.803352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.804452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.804793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.830266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.830589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.830630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [84.830856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [84.830908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.831069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [84.831207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.831278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.831514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.831718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.831913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.832141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.832686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.832938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [84.833133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [84.833322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [84.833537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.833728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.833917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.834103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.834305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.834648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.834968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.835280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.835606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.835919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.837016] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.837321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.863552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.863857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.864067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.864262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.864488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.864497] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.864687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.864791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.864880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.865068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.865062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.865292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.865888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.866141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.866339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.866558] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.866747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.866932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.867121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.867308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.867527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.867857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.868175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.868505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.868797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.869082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.869983] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.870248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.897071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.897461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [84.897441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.897689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [84.897741] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.897892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [84.898013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.898088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.898282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.898508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.898713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.898944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.899580] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.899839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [84.900037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [84.900227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [84.900437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.900632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.900820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.901008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.901212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.901551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.901846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.902135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.902420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.902691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.903572] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.903826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.930094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.930475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [84.930709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [84.930577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.930923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [84.931056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.931134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.931342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.931452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.931661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.931859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.932086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.932701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.932952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [84.933148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [84.933336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [84.933544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.933732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.933921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.934110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.934314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.934636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.934929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.935218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.935500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.935766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.936633] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.936884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.963427] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.963511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.963757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.963799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [84.964010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [84.964048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.964205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [84.964418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.964611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.964805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.964997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.965233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.965585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.965907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.966220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.966542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.966838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.968142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.968460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.980535] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.013437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.013820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.014092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.014340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.014626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.014849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.014775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.015064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.015194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.015275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.015568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.015552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.015920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.016270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.016639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.016983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.017327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.018357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.018721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.046853] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.047181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [85.047461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [85.047479] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.047679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [85.047891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.047929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.048101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.048311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.048301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.048541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.048788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.049150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.049532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.049875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.050215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.050576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.051679] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.052001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.080308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.080454] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.080843] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.080861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.081193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.081231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.081579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.081874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.082157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.082462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.082749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.083069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.083489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.083943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.084397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.084811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.085200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.086597] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.087004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.113823] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.114293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [85.114828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [85.114894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.115181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [85.115499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.115440] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.115769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.115864] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.116029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.116302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.116655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.117085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.117482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.117917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.118322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.118750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.119839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.120262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.146790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.147217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [85.147635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [85.147765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.147930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [85.148204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.148263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.148576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.148746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.148858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.149114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.149425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.149823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.150210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.150635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.151063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.151478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.152580] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.152998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.180528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.180996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.181449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.184824] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469]

<7> [85.187282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.187774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [85.188066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [85.188341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [85.188682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.188992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.189245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.189546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.189805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.190044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.190293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.190554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.190789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.191029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.191273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.191528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.191756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.192049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.192326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.192666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.192920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.193152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.193995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.194220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.201137] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470]

<7> [85.202006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.230065] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.230532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [85.230611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.230842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [85.231129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [85.231107] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.231435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.231583] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.231704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.231967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.232250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.232625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.233024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.233441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.233875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.234292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.234708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.235695] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.236093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.263559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.263984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [85.264344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [85.264765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [85.264869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.265047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.265328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.265357] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.265669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.265847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.265930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.266200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.266607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.266963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.267331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.267730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.268104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.269102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.269483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.296748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.297178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [85.297595] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.297714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [85.298007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [85.298108] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.298288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.298586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.298706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.298978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.299300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.299747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.300326] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.300698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [85.300971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [85.301197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [85.301457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.301677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.301916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.302135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.302362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.302778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.303127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.303486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.303834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.304152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.305051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.305366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.330435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.330550] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.330873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [85.331039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.331241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [85.331510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.331585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [85.331848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.332141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.332403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.332641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.332909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.333465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.333752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [85.333982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [85.334206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [85.334494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.334763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.334988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.335236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.335503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.335857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.336182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.336525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.336910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.337199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.338185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.338478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.363431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.363548] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.363793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [85.363981] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.364075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [85.364332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [85.364364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.364656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.364900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.365137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.365399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.365666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.366171] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.366497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [85.366725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [85.366947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [85.367208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.367468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.367711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.367920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.368142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.368508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.368849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.369161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.369550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.369869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.370682] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.370973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.396853] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.397341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [85.397988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [85.397988] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.398331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [85.398512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.398700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.398972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.398970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.399236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.399613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.399935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.400630] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.400944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [85.401177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [85.401466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [85.401688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.401898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.402099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.402297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.402551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.402874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.403178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.403531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.403801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.404052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.404992] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.405242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.413863] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.446650] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.446985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [85.447237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [85.447536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [85.447657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.447789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.448071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.448104] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.448320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.448532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.448630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.448932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.449300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.449720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.450084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.450446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.450795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.451713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.452075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.480075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.480493] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [85.480596] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.480774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [85.481032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [85.481045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.481279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.481472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.481610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.481849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.482129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.482421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.482786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.483141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.483574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.483921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.484263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.485332] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.485755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.513399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.513543] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.513792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [85.513988] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.514075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [85.514335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [85.514425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.514656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.514953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.515193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.515511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.515778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.516139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.516564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.516911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.517255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.517631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.518610] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.518973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.546879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.547238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [85.547648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [85.547766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.547912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [85.548164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.548251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.548433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.548725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.548693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.548961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.549226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [85.549633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.550026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.550390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.550785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.551126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.552104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.552510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.579951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.580338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [85.580805] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [85.580818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.581153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [85.581305] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.581474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.581761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.581788] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.582006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.582242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.582557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [85.582930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [85.583291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [85.583732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.584078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [85.584435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [85.585434] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.585793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.613523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.613602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [85.613950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [85.614021] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.614259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [85.614486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.614603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.614887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.615163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.615537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.615804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [85.616059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [85.616314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [85.616636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [85.616904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.617145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.617415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.617659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.617938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.618332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.618780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.619222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.619714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.620200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.621449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.621820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.622755] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [85.623035] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [85.646718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.647074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.647457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.647545] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.647745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.648021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.648030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.648341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.648497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.648745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.649151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.649579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.649981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.650324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.650757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.651601] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.651907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.680517] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.681013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.681409] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471]

<7> [85.681444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.701458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [85.701779] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [85.702070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.702346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.702700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.702973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.703278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.703701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.704106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.704480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.704872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.705216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.706202] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.706689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.730025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.730468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.730478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.730788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.730997] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.731104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.731457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.731507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.731760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.732153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.732659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.733050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.733446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.733837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.734210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.735505] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.735916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.763430] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.763839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [85.763937] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.764229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [85.764424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.764637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.764927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.765203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.765580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.765956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.766427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.766906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.767335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.767822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.768215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.769417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.769850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.796723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [85.797072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [85.797433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.797564] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.797721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.797998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.798077] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.798292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.798556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.798666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.799070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.799484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.799923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.800326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.800760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.801903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.802260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.830052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [85.830508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [85.830638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.830816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.831109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.831126] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.831427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.831609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.831727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.832045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.832569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [85.832813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [85.833076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.833297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.833585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.833830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.834064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.834425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.834770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.835110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.835563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.835935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.836836] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.837196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.863488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.863541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.863839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.864029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.864143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.864471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.864509] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.864793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.865038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.865311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.865888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.866128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.866377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.866653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.866885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.867103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.867333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.867753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.868097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.868480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.868819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.869155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.870121] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.870463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.896781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [85.897173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [85.897586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.897721] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.897876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.898183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.898207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.898514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.898693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.898836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.899370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [85.899609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [85.899825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.900029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.900232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.900480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.900708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.901212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [85.901509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [85.901744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.901940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.902133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.902322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.902590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.902913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.903203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.903534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.903895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.904215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.905102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.905393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.929990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.930340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.930753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.930902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.931042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.931318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.931427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.931727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.931853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.932014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.932565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.932830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.933092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.933313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.933631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.933848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.934040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.934461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [85.934647] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [85.934822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.934988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.935153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.935316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.935540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.935798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.936045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.936279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.936599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.936818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.937506] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.937727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.963528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.963640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [85.963991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [85.964019] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.964294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.964491] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.964654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.964937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.965258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.965630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.966034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.966455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.966867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.967210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.967617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.968589] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.968903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.996661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [85.996955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [85.997207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.997500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.997626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.997743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.998037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.998067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.998313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.998484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.998736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.999139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.999526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.999885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.000227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.001267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.001667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.029968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [86.030285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [86.030691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.030786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.031021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.031292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.031275] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.031634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.031753] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.031874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.032123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.032369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.032596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.033516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.033879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.080086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.080536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.080664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.080841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.081125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.081156] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.081473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.081645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.081741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.082053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.082485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.082885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.083275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.083768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.084149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.085228] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.085662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.113514] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.114006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.114456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.114694] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472]

<7> [86.138877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [86.139232] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [86.139504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.139722] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.139933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.140139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.140428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.140779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.141107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.141424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.141727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.142018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.143279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.143565] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.163407] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.163475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.163869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.163869] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.164217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.164242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.164617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.164946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.165318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.165797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.166258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.166756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.167251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.167729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.168180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.169492] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.169938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.197026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [86.197469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [86.197517] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.197809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.198127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.198058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.198488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.198591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.198790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.199185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.199673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.200106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.200617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.201079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.201521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.202717] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.203153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.229916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [86.230272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [86.230688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.230811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.230987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.231265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.231296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.231609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.231795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.231911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.232315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.232777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.233216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.233665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.234037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.235445] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.235847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.263291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [86.263695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [86.263819] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.263972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.264239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.264264] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.264546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.264712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.264790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.265095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.265506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.265867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.266212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.266638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.266978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.267867] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.268228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.296574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.296927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.297236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.297599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.297736] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.297857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.298152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.298184] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.298486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.298622] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.298855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.299213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.299604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.299999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.300337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.301255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.301657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.329981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [86.330335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [86.330740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.330833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.331005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.331260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.331278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.331641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.331725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.331943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.332307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.332721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.333082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.333442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.333780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.334745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.335106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.363212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.363640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.363774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.363917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.364176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.364216] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.364489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.364648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.364742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.365016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.365400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.365786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.366131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.366563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.366903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.367981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.368367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.396797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [86.397093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [86.397392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.397525] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.397634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.397887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.397964] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.398141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.398382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.398443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.398976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [86.399234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [86.399520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.399793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.400018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.400260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.400558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.400903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.401268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.401657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.402038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.402392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.403329] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.403759] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.429832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [86.430106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [86.430391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.430533] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.430613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.430845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.430937] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.431119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.431291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.431803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.432362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [86.432618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [86.432873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.433152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.433445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.433690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.433952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.434356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.434744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.435102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.435467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.435806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.436682] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.437001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.463505] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.464002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.464369] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473]

<7> [86.464483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.489245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.489699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [86.489934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [86.490134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [86.490320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.490521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.490695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [86.490866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [86.491032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.491193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.491373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [86.491535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [86.491690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.491840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.491984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.492134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.492320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.492765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.492960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [86.493094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [86.493217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [86.493354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.493483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.493606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [86.493726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [86.493849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.493958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.494067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [86.494174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [86.494283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.494403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.494510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.494617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.494732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.494911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.495076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.495234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.495395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.495549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.496483] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.496657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.512800] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [86.531503] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474]

<7> [86.548389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.548877] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.549271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.554190] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.555723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.556154] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.579879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.580318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [86.580784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [86.580926] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.581109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [86.581499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.581507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.581859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.581977] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.582162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.582577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.582951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.583751] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.584102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [86.584393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [86.584652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [86.584904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.585165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.585495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.585771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.586030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.586441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.586879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.587252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.587646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.587980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.588838] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.589151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.613300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.613788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.613909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [86.614294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [86.614327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.614716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [86.614872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.615031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.615433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.615773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.616059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.616402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.616857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.617269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.617713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.618129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.618530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.619516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.619853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.646575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.647028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [86.647424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [86.647583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.647724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [86.648032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.648111] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.648419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.648639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.648715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.649004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.649355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.649778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.650175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.650753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.651137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.651626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.652899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.653294] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.680125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.680612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [86.680694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.680972] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [86.681258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [86.681245] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.681610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.681728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.681878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.682143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.682491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.682782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.683173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.683598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.683999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.684404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.684805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.685875] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.686264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.713168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.713644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [86.713722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.713964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [86.714252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [86.714208] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.714616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.714688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.714942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.715200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.715531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.715820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.716213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.716675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.717098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.717515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.717930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.719018] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.719395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.746473] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.746819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [86.747100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [86.747388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [86.747399] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.747620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.747782] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.747860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.748126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.748141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.748442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.748735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.749135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.749583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.749982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.750588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.750971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.752474] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.752884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.764139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.796641] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.797249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [86.797835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [86.797862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.798213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [86.798564] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.798666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.799019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.799096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.799472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.799822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.800254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.800818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.801267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.801746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.802180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.802601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.803719] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.804131] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.829918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.830474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [86.830553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.830802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [86.831085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [86.831055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.831391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.831526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.831710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.831975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.832294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.832660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.833076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.833447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.833800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.834195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.834606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.835807] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.836200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.863157] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.863727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.864005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [86.864212] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.864411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [86.864706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [86.864701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.864988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.865309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.865648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.865922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.866220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.866662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.867053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.867524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.867917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.868320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.869525] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.869932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.896792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.897187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [86.897592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [86.897743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.897858] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [86.898111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.898188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.898397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.898638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.898624] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.898906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.899171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [86.899569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [86.899977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [86.900336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.900729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [86.901069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [86.902100] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.902495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.929782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.930210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [86.930622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [86.930746] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.930893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [86.931200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.931194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.931523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.931641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.931769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.932007] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.932273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [86.932713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [86.933070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [86.933479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.933820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [86.934161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [86.935165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.935568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.963494] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.963986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.964418] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.965048] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475]

<7> [86.986894] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.987227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [86.987544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [86.987745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [86.987939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.988120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.988292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.988548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.988727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.988883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.989031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.989176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.989312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.989602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.989730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.989855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.990003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.990300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.990499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [86.990613] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [86.990723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [86.990830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.990935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.991034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.991136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.991237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.991347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.991444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.991537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.991624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.991712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.991800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.991885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.991977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.992122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.992262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.992413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.992544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.992670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.993213] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.993428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.997300] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476]

<7> [87.009083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.029844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.030253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.030704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.030845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.030981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.031246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.031297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.031621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.031741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.031907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.032142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.032434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.032889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.033142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.033410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.033591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.033772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.033984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.034164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.034349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.034527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.034790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.035033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.035268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.035560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.035776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.036341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.036557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.063266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.063818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [87.063895] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.064167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [87.064417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.064508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [87.064789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.064843] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.065064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.065352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.065670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.065981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.066704] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.067051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [87.067313] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [87.067639] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [87.067891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.068137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.068418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.068651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.068896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.069283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.069738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.070180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.070592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.070951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.071918] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.072258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.096515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.096942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.097288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.097680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.097829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.097958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.098226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.098362] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.098550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.098785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.098860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.099151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.099844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.100157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.100547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.100792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.101089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.101358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.101653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.101904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.102154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.102583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.103030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.103393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.103779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.104096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.104964] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.105272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.130099] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.130575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [87.130652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.130911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [87.131099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.131172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [87.131466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.131530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.131711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.131951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.132242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.132579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.132969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.133343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.133738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.134077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.134430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.135482] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.135840] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.163089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.163568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [87.163648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.163850] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [87.164106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [87.164097] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.164392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.164529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.164638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.164929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.165170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.165474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.165835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.166234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.166616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.166956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.167292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.168353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.168717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.196485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.196828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [87.197073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [87.197307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [87.197683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.197807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.197963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.198210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.198300] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.198507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.198761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.198789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.199142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.199562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.199902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.200298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.200714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.202036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.202453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.213607] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.246361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.246691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.246991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.247256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.247598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.247733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.247854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.248150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.248179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.248439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.248621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.248714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.249081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.249470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.249885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.250238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.250684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.251561] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.251924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.279758] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.280148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [87.280526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [87.280656] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.280788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [87.281037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.281101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.281372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.281545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.281615] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.281857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.282125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.282528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.282884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.283233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.283683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.284056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.285093] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.285487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.313047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.313432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.313537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.313720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.313960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.313947] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.314185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.314303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.314453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.314675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.314938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.315214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.315642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.315992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.316363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.316706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.317111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.318143] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.318540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.346472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.346695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [87.346863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [87.347029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [87.347195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.347398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.347564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.347537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.347736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.347875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.347918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.348160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.348173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.348483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.348738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.348981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.349222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.349925] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.350201] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.379596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.379871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [87.380107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [87.380341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [87.380541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.380468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.380757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.380969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.380890] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.381180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.381277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.381475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.381824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.382164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.382586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.382922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.383256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.384220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.384602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.412968] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [87.413388] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [87.413483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.413718] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [87.413908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.414036] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [87.414258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.414374] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [87.414726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.415025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [87.415348] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [87.415669] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [87.416004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [87.416376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [87.416705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [87.417031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [87.417373] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [87.417696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [87.418013] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [87.418344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [87.418663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled

<7> [87.418981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [87.419297] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [87.419679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14

<7> [87.420051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [87.420415] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [87.420735] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [87.421025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [87.421336] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [87.421622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [87.421927] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [87.422278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [87.422645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [87.422951] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [87.423249] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [87.423565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [87.423839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [87.424101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [87.424365] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [87.424616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [87.424880] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [87.425112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [87.425359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [87.425574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [87.425794] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [87.425998] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [87.426197] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [87.426426] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [87.426615] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [87.426801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [87.426977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [87.427153] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [87.427334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [87.427504] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [87.427672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [87.427839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [87.428004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.428165] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.428362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.428539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [87.428688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [87.428835] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.428975] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.429111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [87.429245] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [87.429402] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [87.429531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes

<7> [87.429661] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [87.429790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0

<7> [87.429914] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no

<7> [87.430034] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [87.430149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes

<7> [87.430262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [87.430389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0

<7> [87.430526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.430655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.430838] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1

<7> [87.431001] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on

<7> [87.431143] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [87.446104] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [87.447462] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [87.447639] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [87.450189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0

<7> [87.450352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [87.450480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0

<7> [87.450605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [87.450729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.450852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.450998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.451132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [87.451255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.451422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.451548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.451670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [87.451791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.451907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.452020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [87.452159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [87.452353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [87.452537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [87.452716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [87.452888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [87.453064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [87.453494] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<6> [87.466763] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS

<7> [87.467552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051

<7> [87.467708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.467845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [87.467978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87

<7> [87.468119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88

<7> [87.468275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1

<7> [87.468468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [87.468634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [87.468796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [87.468953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [87.469103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [87.479360] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [87.481065] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<6> [87.482406] [IGT] kms_rotation_crc: exiting, ret=0

<6> [87.496672] Console: switching to colour frame buffer device 180x56

<7> [87.513474] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.514006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.514542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.514967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.515465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.547452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.547900] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.548280] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

Results for igt@kms_rotation_crc@multiplane-rotation-cropping-top