igt@kms_rotation_crc@multiplane-rotation-cropping-top on shard-lnl@xe-4268-d2fe88bbc66599aedc08d081a76460e34fb56786 Test details

Detail	Value
Duration	10.77 seconds
Hostname	shard-lnl-7
Igt-Version	IGT-Version: 2.3-gf38f4d8e9 (x86_64) (Linux: 6.19.0-rc1-lgci-xe-xe-4268-d2fe88bbc66599aed+ x86_64)
Out	Using IGT_SRANDOM=1766171892 for randomisation Opened device: /dev/dri/card0 Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.765s)
Err	Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.765s)
Dmesg	<6> [77.524783] Console: switching to colour dummy device 80x25 <6> [77.524852] [IGT] kms_rotation_crc: executing <7> [77.530497] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [77.530507] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [77.530667] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [77.530758] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [77.530967] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [77.530970] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [77.531080] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [77.531161] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [77.531804] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [77.531808] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [77.531937] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [77.532032] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <7> [77.532318] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] <7> [77.532321] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1] <7> [77.532782] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [77.533091] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [77.533194] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [77.533301] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [77.533425] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [77.533431] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [77.533432] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [77.533434] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7> [77.533436] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [77.533438] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [77.533440] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor <5> [77.533442] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [77.533443] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0 <5> [77.533445] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [77.533458] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes <7> [77.533564] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [77.533650] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [77.534152] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [77.534154] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [77.534155] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [77.534210] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes: <7> [77.534213] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [77.534217] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [77.534229] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [77.534232] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [77.534489] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [77.534499] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [77.534502] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [77.534628] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [77.534636] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [77.534638] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [77.534748] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <6> [77.534846] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top <7> [77.536187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0 <7> [77.536255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [77.536333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [77.536408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [77.536481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [77.536573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [77.536666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [77.536749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [77.536829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [77.536909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [77.536989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [77.537268] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.537447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.537608] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [77.565157] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [77.565440] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [77.565621] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [77.565726] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [77.565815] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [77.565903] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation <7> [77.565979] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [77.566068] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [77.566182] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [77.566309] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [77.566415] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [77.566516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [77.566602] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [77.566688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [77.566772] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [77.566855] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [77.566938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [77.567019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [77.567101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [77.567180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [77.567258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [77.567352] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [77.567438] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8 <7> [77.567523] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [77.567607] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [77.567686] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [77.567759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [77.567833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [77.567905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [77.567977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [77.568049] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [77.568121] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [77.568193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [77.568265] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [77.568357] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [77.568436] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [77.568513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [77.568590] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [77.568668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [77.568747] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [77.568815] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [77.568884] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [77.568954] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [77.569023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [77.569105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [77.569174] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [77.569243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [77.569326] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [77.569406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [77.569495] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [77.569585] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [77.569675] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [77.569749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [77.569821] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [77.569892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [77.569963] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570173] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [77.570242] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [77.570325] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570401] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570477] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [77.570552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [77.570627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [77.581878] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [77.581994] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [77.602341] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.602713] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.603013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.621831] xe 0000:00:02.0: [drm:intel_dp_dump_link_status [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] ln0_1:0x77 ln2_3:0x77 align:0x80 sink:0x1 adj_req0_1:0x0 adj_req2_3:0x0 <7> [77.622316] xe 0000:00:02.0: [drm:intel_dp_link_ok [xe]] [ENCODER:390:DDI A/PHY A] 8b/10b link not ok, retraining <7> [77.634737] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427] <7> [77.636103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [77.636540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [77.636847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.637131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.637468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.637802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.638127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.638477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.638737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.639017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.639345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.639942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [77.640222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [77.640541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.640794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.641039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.641730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.641989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.642222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.642549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.642789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.643319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.643921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [77.644218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [77.644563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.644825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.645075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.645429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.645670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.645903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.646119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.646379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.647724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.648008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.648284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.648593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.648833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.649066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.649809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.650047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.650708] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [77.650883] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [77.664638] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1 <7> [77.667263] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430] <7> [77.699279] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.699783] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.700213] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.701015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431] <7> [77.701959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [77.702321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [77.702619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.702905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.703188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.703596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.703919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.704334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.704729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.705126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.705554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.705941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.706413] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz <7> [77.707397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.707795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.732337] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432] <7> [77.732255] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.732483] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.732617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.732980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [77.733234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [77.733324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.733406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.733488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.733564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.733650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.733762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.733871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.733972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.734061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.734150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.734876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.734999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.765246] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.765415] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433] <7> [77.765470] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.765594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.766020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [77.766167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [77.766275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.766341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.766405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.766468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.766549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.766646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.766741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.766830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.766910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.766989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.767810] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.767913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.799368] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434] <7> [77.799287] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.799634] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.799928] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.816825] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [77.817085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [77.817350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.817553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.817749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [77.817980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [77.818270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.818578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.818843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.819153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.819463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.819697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.820390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.820629] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.848552] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435] <7> [77.850237] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.850687] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.851040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.865688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [77.865983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [77.866269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.866511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [77.866749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [77.867039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [77.867710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.868062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.868441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.868775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.869087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.869470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.870558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.870881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.898734] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436] <7> [77.899234] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.899680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [77.899807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.900078] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [77.900289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.900469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.900763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.901051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.901403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.901717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.902123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.902587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.903034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.903459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.903882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.905065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.905512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.916002] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437] <7> [77.949196] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438] <7> [77.949298] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.949726] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.949912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [77.950080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.950256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [77.950519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.950766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [77.951004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [77.951299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [77.951565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [77.951906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [77.952265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [77.952645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.953025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [77.953380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [77.954236] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.954582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [77.982213] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439] <7> [77.982162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [77.982554] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [77.982878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [77.982945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [77.983220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [77.983443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [77.983649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [77.983850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [77.984070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [77.984341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [77.984616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [77.984878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [77.985148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.985401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [77.985649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [77.986402] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [77.986675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.015171] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.015560] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.015873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.018431] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440] <7> [78.019237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [78.019446] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [78.019624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.019796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.020005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.020259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.020465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.020729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.020981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.021252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.021488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.021771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.022608] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.022887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.049061] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441] <7> [78.049232] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.049671] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.050038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.071765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [78.071973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [78.072154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.072291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.072423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.072561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.072726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [78.072901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [78.073074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [78.073252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.073400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [78.073543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [78.074025] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.074200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.098949] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442] <7> [78.099136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.099559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.100988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.118637] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [78.118978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [78.119332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.119583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.119822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.120123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.120387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.120729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.121043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.121439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.121741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.122011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.122936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.123325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.148337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [78.148615] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [78.148851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.149126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.149137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.149364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.149605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.149576] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.149825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.149937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.150059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.150366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.150595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.151015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [78.151444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [78.151723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.151954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.152218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.152432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.152639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.152844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.153051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.153338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.154142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.154510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.198362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.198633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.198849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.199048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.199378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.199492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.199633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.199875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.199880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.200251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.200344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.200550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.200750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.200959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.201174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.201354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.201541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.201867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.202157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.202423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.202713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.202975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.203827] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.204141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.255801] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443] <7> [78.255788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.255923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.256018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.256398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [78.256476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [78.256540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.256599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.256655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.256709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.256773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.256909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [78.256969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [78.257022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.257095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.257150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.257210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.257278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.257425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [78.257481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [78.257529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.257577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.257624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.257671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.257720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.257801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.257883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.257963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.258047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.258146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.258506] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.258610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.281432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.281617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.281787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.281970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.282182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.282337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.282312] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.282517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.282628] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.282831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.282882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.282975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.283155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.283297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.283433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.283571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.283712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.284007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.284198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.284322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.284442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.284556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.284667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.284782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.284966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.285171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.285349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.285518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.285682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.286269] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.286456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.315173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.315346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [78.315673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [78.315718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.315973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.316258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.316352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.316641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.316970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.317392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.317826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.318344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.318764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.319281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.319723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.320737] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.321237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.348205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [78.348505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [78.348757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.348991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.349321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.349435] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.349567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.349871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.349883] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.350308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.350324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.350667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.351063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.351451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.351784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.352868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.353265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.381564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [78.381865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [78.382198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.382323] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.382434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.382664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.382737] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.382941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.383120] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.383236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.383596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.383897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.384241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.384606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.384906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.385789] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.386096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.414829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.415117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.415219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.415328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.415534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.415632] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.415745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.416052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.416031] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.416317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.416639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.417011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.417333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.417679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.417981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.418845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.419211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.448198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [78.448439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [78.448641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.448881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.449161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.449258] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.449375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.449606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.449673] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.449991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.450054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.450284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.450566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.450866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.451179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.451967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.452326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.481479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [78.481717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [78.481937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.482221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.482269] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.482436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.482683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.482683] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.482937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.483084] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.483355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.483690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.484109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.484511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.484868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.486053] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.486468] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.515067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [78.515089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.515276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [78.515455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.515445] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.515627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.515797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.515748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.516002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.516715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [78.517033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [78.517325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [78.517622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.517902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [78.518222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [78.519126] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.519407] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.548124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [78.548336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [78.548527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.548753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.548979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.549165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.549131] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.549372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [78.549513] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.549687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [78.549839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.549997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [78.550281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.550567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [78.550877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [78.551727] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.552016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.580151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.580504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.581465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.581779] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [78.581780] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [78.581970] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [78.584784] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444] <7> [78.586063] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.586363] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [78.586599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [78.586804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [78.587047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.587245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.587452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.587641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.587827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.588037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [78.588210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [78.588376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [78.588539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.588699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.588860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.589071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.589279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.589578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.589926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.590258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.590519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.590776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.591564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.591831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.597804] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [78.617290] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445] <7> [78.618686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.648106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.648395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.648609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.648810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.649058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.649167] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.649245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.649426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.649502] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.649604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.649786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.649850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.650181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.650469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.650741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.651104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.651432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.652164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.652456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.681466] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.681769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [78.682100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [78.682322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [78.682242] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.682540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.682662] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.682800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.683074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.683058] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.683336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.683595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.683914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.684222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.684531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.684834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.685233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.686353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.686658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.714771] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.715148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.715245] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.715443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.715666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.715625] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.715876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.715998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.716124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.716362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.716562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.716806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.717225] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.717444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.717652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.717833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.718101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.718264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.718422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.718577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.718744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.719029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.719283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.719535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.719837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.720117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.720879] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.721192] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.748467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.748801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [78.749103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [78.749243] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.749315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [78.749517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.749603] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.749710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.749923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.749938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.750135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.750329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.750700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.750925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [78.751108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [78.751283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [78.751491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.751680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.751855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.752152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.752345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.752642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.752950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.753279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.753563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.753830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.754638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.754919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.781469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.781807] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [78.782118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [78.782147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.782331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [78.782529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.782507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.782720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.782810] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.782938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.783115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.783356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.783738] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.783982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [78.784168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [78.784341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [78.784554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.784744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.784949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.785107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.785271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.785525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.785778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.786071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.786307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.786542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.787284] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.787557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.814745] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.815073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [78.815161] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.815317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [78.815513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [78.815492] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.815700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.815775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.815958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.816131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.816301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.816488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.816911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.817130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [78.817306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [78.817469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [78.817629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.817787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.817988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.818150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.818312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.818571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.818829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.819123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.819421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.819662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.820395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.820704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.831785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.864728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.865114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.865197] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.865371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.865593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.865579] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.865809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.865961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.866146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.866377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.866599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.866897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.867222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.867525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.867825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.868253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.868610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.869379] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.869686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.898085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.898379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [78.898629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [78.898852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [78.899025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.898976] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.899197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [78.899291] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.899362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [78.899552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [78.899560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.899735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.900029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.900291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.900547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.900862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.901125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.902121] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.902391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.931344] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.931618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [78.931866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [78.932088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [78.931996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.932302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.932415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.932533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [78.932736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [78.932772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.932987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [78.933629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.933965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.934262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [78.934552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.934910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [78.935208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [78.936030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.936310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.964890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.964950] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.965119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [78.965282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [78.965284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.965440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [78.965593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.965549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.965743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.965933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [78.966094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [78.966313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [78.966571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [78.966832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [78.967098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.967418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [78.967681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [78.968457] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [78.968722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [78.997992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [78.998226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [78.998414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [78.998567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [78.998719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [78.998929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [78.999097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [78.999051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [78.999260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [78.999385] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [78.999441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [78.999669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [78.999693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [78.999970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [79.000228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.000473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [79.000747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [79.001521] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.001812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.031878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.032259] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.032531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.056339] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446] <7> [79.056992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.057111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [79.057176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [79.057237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [79.057296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.057353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.057410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.057465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.057518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.057570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.057628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.057680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.057729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.057793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.057848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.057902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.057968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.058059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.058144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.058225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.058305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.058385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.058686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.058793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.065589] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447] <7> [79.066233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.098127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.098518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.098905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.099042] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.099199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.099506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.099593] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.099828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.100117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.100129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.100456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.100819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.101248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.101718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.102215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.102579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.102985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.103841] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.104203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.131417] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.131791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [79.131907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.132047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [79.132289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [79.132317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.132518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.132672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.132779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.133012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.133251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.133515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.133908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.134307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.134653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.135036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.135404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.136784] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.137177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.164789] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.165128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.165423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.165644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.166113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.166066] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.166350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.166481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.166573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.166904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.166873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.167222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.167557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.167926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.168264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.168580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.168955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.169869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.170191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.198341] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.198710] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [79.199059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [79.199193] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.199286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [79.199500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.199573] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.199709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.199999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.199957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.200219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.200469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.200816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.201143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.201499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.201834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.202166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.203017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.203303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.231339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.231650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [79.231987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [79.232118] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.232187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [79.232375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.232451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.232555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.232753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.232768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.232934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.233127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.233494] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.233744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [79.233903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [79.234097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [79.234282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.234439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.234628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.234871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.235036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.235275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.235513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.235772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.236020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.236327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.237061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.237315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.264749] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.265023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [79.265230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [79.265420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [79.265605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.265833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.265855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.266017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.266192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.266236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.266477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.266459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.266911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.267137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [79.267319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [79.267496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [79.267670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.267919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.268108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.268337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.268543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.268875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.269195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.269508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.270031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.270318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.271313] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.271621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.281463] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.314598] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.314909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.315133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.315323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.315511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.315778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.315961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.315928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.316162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.316244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.316372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.316510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.316834] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.317038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.317211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.317378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.317541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.317727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.317931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.318142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.318328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.318608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.318911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.319201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.319484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.319822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.320492] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.320804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.348085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.348400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [79.348642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [79.348919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [79.349106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.349054] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.349285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.349388] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.349458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.349650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.349701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.349907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.350329] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.350529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [79.350709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [79.350869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [79.351030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.351223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.351405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.351561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.351767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.352020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.352259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.352524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.352790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.353031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.354038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.354310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.381399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.381884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [79.381948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.382199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [79.382459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [79.382433] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.382757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.382868] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.383004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.383307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.383541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.383922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.384284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.384666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.385019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.385416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.385813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.386804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.387166] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.414904] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.415237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [79.415498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [79.415782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [79.415916] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.415998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.416210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.416297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.416424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.416623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.416704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.416961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [79.417269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.417566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.417943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.418233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.418539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.419400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.419725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.447924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [79.448215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [79.448437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [79.448660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [79.448792] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.448844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.449033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.449114] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.449195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.449355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.449408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.449536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [79.449814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [79.450074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [79.450329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.450580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [79.450866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [79.451697] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.451985] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.481322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [79.481525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [79.481759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [79.481935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.481902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.482110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.482276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.482238] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.482475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.482525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.482783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [79.482949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [79.483100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [79.483245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [79.483388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.483530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.483716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.483857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.484057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.484313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.484567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.484858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.485182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.485450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.486279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.486586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.487410] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [79.487684] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [79.514631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [79.514858] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [79.515054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.515243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.515426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.515715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.515822] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.515925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.516154] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.516202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.516438] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.516463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.516748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.517000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.517266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.517967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.518239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.548639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.548925] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448] <7> [79.549025] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.549349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.549818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [79.550026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [79.550208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.550386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.550567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.550856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.551080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.551355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.551647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.551916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.552180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.552497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.553287] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.553569] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.581260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [79.581444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [79.581657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.581827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.581772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.581991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.582098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.582167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.582341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.582363] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.582592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.582828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.583067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.583314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.583590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.584274] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.584515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.614852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [79.615026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [79.615182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.615332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.615480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.615669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.615692] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.615841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.616012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.616096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.616296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.616348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.616606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.616864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.617122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.617878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.618153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.647874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [79.648089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.648261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.648413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.648611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.648763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.648717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.648969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.649032] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.649231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.649339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.649481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.649761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.650016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.650303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.651054] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.651309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.681285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [79.681505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [79.681776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.681962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.681894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.682131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.682243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.682332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.682528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.682586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.682848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.683098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.683333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.683569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.683846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.684437] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.684751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.714611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [79.714833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [79.715032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.715259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.715484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.715779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.715931] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.716008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.716302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.716311] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.716604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.716681] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.716902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.717208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.717512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.718357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.718710] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.747927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [79.748123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [79.748304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.748476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.748718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.748894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.748837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.749130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.749192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.749544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [79.749496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.749716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [79.749882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.750062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.750211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.750358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.750532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.750787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.751024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.751251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.751547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.751779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.752415] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.752705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.781252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [79.781444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [79.781675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.781802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.781876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.782059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.782146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.782235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.782427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.782449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.782841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [79.783005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [79.783162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.783344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.783540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.783707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.783869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.784106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.784339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.784590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.784841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.785097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.785820] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.786068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.814971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [79.815233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [79.815473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.815843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.816090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.815987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.816330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.816480] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.816744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.817010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.817281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [79.817545] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [79.817779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.817999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.818204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.818406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.818679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.819141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [79.819350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [79.819633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.819831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.820027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [79.820223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [79.820433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [79.820825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [79.821221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [79.821568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.821896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [79.822208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [79.823017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.823319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.847914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [79.848193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.848424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.848725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.848846] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.848939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.849202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.849242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.849511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.849641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.849980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [79.850200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.850407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.850727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.850933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.851134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.851342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.851854] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [79.852087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [79.852300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.852493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [79.852674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [79.852849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [79.853034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.853309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.853615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.853869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.854114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.854363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.855089] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.855326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.881367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [79.881771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [79.881881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.882052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.882312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.882327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.882613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.882767] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.882893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.883135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.883351] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.883614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.883832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.885340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.885770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.931197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.931414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.931664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.931779] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.931846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.932031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.932112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.932230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.932397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.932439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.932753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.933018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [79.933310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.933586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [79.933821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [79.934489] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.934745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.965589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.965972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.966135] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449] <7> [79.966281] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.966897] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [79.967113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [79.967309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.967539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [79.967732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [79.968023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [79.968283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [79.968632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [79.968928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [79.969200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.969547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [79.969811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [79.970579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [79.970860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [79.997845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [79.998102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [79.998318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [79.998577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [79.998716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [79.998778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [79.999005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [79.999062] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [79.999242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [79.999348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [79.999528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [79.999790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.000062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.000335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.000682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.001543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.001852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.031518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [80.031558] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.031764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [80.031986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.031968] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.032197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.032318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.032508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.032719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.032956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.033281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.033633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.034006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.034372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.034726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.035555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.035879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.064569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [80.064778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [80.064964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.065202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.065456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.065486] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.065664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.065898] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.065945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.066258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.066263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.066667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.067030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.067346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.067684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.068523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.068819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.097909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [80.098121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [80.098313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.098601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.098792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.098756] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.098973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.099125] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.099163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.099448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.099461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.099715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.099978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.100273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.100548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.101157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.101446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.131175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [80.131404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [80.131525] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.131591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.131806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.131879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.131994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.132205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.132186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.132421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.132696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.132970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.133235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.133576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.133838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.134503] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.134799] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.164553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [80.164737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [80.164905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.165115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.165319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.165569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.165712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.165778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.166068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.166096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.166355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.166459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.166750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.167065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.167322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.168076] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.168408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.180446] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off <7> [80.180730] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [80.197790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [80.197956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [80.198108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.198261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.198464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.198626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.198588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.198807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.198923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.199069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.199224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.199332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.199638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.199946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.200241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.201006] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.201282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.231484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [80.231478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.231687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [80.231876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.231856] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.232058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.232227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.232173] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.232430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.232625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [80.232947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [80.233197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [80.233469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.233770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [80.234037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [80.234763] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.235038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.264535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [80.264742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [80.264933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.265161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.265393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.265431] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.265595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.265799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [80.265812] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.266076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.266122] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.266354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.266670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.266924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.267162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.267874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.268130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.298375] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.298823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.299179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.323466] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450] <7> [80.324006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.324108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [80.324170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [80.324228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [80.324285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.324359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.324418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.324477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.324532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.324583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [80.324642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [80.324700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [80.324757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.324814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.324868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.324921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.324991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.325116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.325185] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [80.325239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [80.325291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [80.325357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.325410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.325465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.325523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.325583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.325642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [80.325699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [80.325752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [80.325802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.325854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.325906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.325953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.326004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.326085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.326166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.326244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.326328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.326413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.326854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.326942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.330867] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [80.349453] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451] <7> [80.350532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.381367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.381422] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.381762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.381916] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.382072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.382409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.382395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.382705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.383048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.383352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.383677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.383998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.384567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.384908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.385243] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.385589] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.385904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.386194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.386502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.386783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.387063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.387463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.387812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.388238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.388627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.389003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.389858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.390190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.414594] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.414950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [80.415328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [80.415461] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.415592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [80.415848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.415913] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.416094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.416360] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.416409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.416684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.416958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.417596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.417895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [80.418190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [80.418467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [80.418713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.418938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.419164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.419427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.419661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.419981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.420306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.420666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.420974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.421294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.422099] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.422383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.447806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.448137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.448431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.448558] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.448653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.448859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.448942] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.449074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.449324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.449337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.449562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.449839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.450431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.450713] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.450997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.451220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.451526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.451775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.452006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.452246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.452547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.452885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.453204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.453591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.453904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.454188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.455092] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.455385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.481370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.481465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.481814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [80.481784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.482072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [80.482137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.482418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [80.482711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.482940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.483143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.483432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.483686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.483998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.484312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.484660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.484951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.485240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.486101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.486438] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.514525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.514922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [80.515182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [80.515505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [80.515734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.515643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.515956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.516079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.516176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.516458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.516482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.516700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.517036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.517447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.517743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.518032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.518429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.519417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.519745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.547780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.548050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [80.548303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [80.548412] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.548497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [80.548681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.548745] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.548859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.549035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.549029] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.549218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.549459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.549707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.549952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.550199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.550548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.550860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.551816] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.552066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.564762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.597715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.597984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.598265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.598373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.598464] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.598654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.598731] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.598841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.599020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.599027] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.599242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.599431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.599694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.599951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.600205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.600506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.600811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.601527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.601794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.631121] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.631462] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [80.631511] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.631663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [80.631847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [80.631864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.632022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.632198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.632164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.632430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.632593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.632778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.633066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.633328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.633567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.633800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.634032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.634804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.635063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.664438] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.664704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [80.664905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [80.665091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [80.665313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.665490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.665453] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.665664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.665831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.665810] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.666057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.666107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.666355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.666608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.666859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.667090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.667409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.668077] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.668376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.697997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.698327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [80.698418] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.698553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [80.698764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [80.698826] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.698970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.699159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.699240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.699413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.699619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.699839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [80.700120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [80.700437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [80.700708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.700982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [80.701325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [80.702196] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.702478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.731083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.731395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [80.731473] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.731646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [80.731847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [80.731858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.732026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.732255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.732218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.732430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.732608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.732805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [80.733076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [80.733355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [80.733601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.733843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [80.734086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [80.734768] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.735008] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.765266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.765633] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.765948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452] <7> [80.765918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.767577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.767833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [80.768022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [80.768229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [80.768394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.768557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.768715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.768900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.769086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.769297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.769462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.769620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.769774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.769962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.770139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.770358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.770541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.770783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.771021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.771301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.771604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.771845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.772722] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.772972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.783907] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453] <7> [80.785769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.814519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.814890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.815205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.815447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.815675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.815897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.816133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.816437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.816529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.816695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.816910] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.817199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.817277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.817475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.817689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.817876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.818058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.818317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.818499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.818676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.818864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.819171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.819467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.819758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.820047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.820372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.821128] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.821465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.847907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.848290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [80.848373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.848573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [80.848792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [80.848756] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.849000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.849086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.849316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.849539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.849808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.850053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.850696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.850962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [80.851238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [80.851440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [80.851642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.851839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.852038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.852315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.852525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.852851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.853165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.853515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.853870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.854204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.855078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.855432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.881191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.881524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.881772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.881995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.882244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.882441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.882376] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.882634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.882735] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.882860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.883045] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.883064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.883471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.883692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [80.883895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [80.884058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [80.884249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.884401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [80.884551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [80.884721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [80.884905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.885179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.885436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.885691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.885943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.886228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.886874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.887142] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.914697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.915040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [80.915440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [80.915581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.915695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [80.915934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.915996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.916169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.916406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.916384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.916609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.916844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.917404] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.917648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [80.917841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [80.918028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [80.918299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.918483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.918666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [80.918843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [80.919034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.919350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.919681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.919965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.920269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.920534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.921315] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.921588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.948263] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.948647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.948652] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.948970] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [80.948976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.949316] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [80.949528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [80.949721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.949945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.950166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.950356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.950587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.951034] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.951276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [80.951447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [80.951607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [80.951765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.951923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [80.952081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [80.952295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [80.952459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [80.952710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [80.952962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [80.953297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.953551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [80.953799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [80.954585] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.954857] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.981147] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [80.981521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [80.981759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [80.981975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [80.982240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [80.982277] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [80.982450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [80.982657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [80.982687] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [80.982899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [80.983013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [80.983163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [80.983451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [80.983733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [80.984011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.984356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [80.984609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [80.985573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [80.985842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [80.998159] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.031024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.031342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [81.031546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [81.031740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [81.031923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.032242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.032344] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.032428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.032602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.032676] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.032801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.032961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.033086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.033356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.033621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.033877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.034141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.034775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.035036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.064390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.064676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [81.064906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [81.065153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [81.065190] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.065360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.065564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.065572] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.065755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.065936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.065894] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.066177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.066455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.066730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.067047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.067395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.067682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.068501] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.068795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.097693] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.097983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [81.098277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [81.098457] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [81.098416] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.098628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.098729] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.098796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.098974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.099006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.099250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.099461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.099730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.099994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.100368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.100671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.100938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.101780] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.102083] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.131275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.131565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [81.131813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [81.132007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [81.132292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.132420] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.132495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.132704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.132803] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.132888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.133120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [81.133159] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.133419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.133712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.134032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.134373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.134654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.135523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.135803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.164367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [81.164700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [81.164955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [81.165270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [81.165396] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.165506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.165727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.165805] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.165947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.166236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.166207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.166474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [81.166805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [81.167184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [81.167503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.167818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [81.168219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [81.169134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.169464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.197814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [81.198123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [81.198203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.198368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [81.198565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.198559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.198743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.198865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.198923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.199148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.199326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [81.199498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [81.199666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [81.199836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [81.199995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.200201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.200353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.200506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.200680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.200938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.201224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.201528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.201774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.202037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.202752] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.203035] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.203720] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [81.203948] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [81.231047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.231281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.231470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.231645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.231816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.232076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.232202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.232308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.232543] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.232584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.232831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.232845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.233140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.233460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.233761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.234497] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.234801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.265214] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454] <7> [81.265117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.265537] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.265916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.282770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [81.283135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [81.283413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.283675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.283933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.284460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.284750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.285124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.285411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.285697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.285973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.286291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.287142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.287439] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.314467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.314733] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.314952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.315256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.315493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.315770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.316037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.316073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.316471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.316487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.316822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.316873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.317227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.317620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.318011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.319375] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.319832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.348031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [81.348312] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [81.348546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.348762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.349010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.349043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.349239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.349384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.349546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.349692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.350043] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [81.350285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [81.350513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.350764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.351004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.351227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.351457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.351809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.352190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.352566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.352907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.353288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.354365] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.354737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.381102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [81.381379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [81.381612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.381829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.382108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.382228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.382335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.382641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.382637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.383020] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.383222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [81.383451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [81.383663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.383865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.384136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.384396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.384624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.384986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.385347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.385655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.385973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.386278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.387190] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.387529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.414397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [81.414671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [81.414906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.415234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.415353] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.415475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.415747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.415771] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.416054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.416177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.416519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [81.416737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [81.416957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.417166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.417373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.417602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.417811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.418309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [81.418536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [81.418729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.418921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.419184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.419397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.419638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.419983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.420273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.420556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.420900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.421254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.421990] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.422270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.447698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.448025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.448155] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.448287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.448527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.448567] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.448762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.448920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.449108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.449424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.450027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.450273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.450517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.450752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.451037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.451287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.451531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.452082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.452305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.452513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.452715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.452984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.453202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.453412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.453718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.454027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.454303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.454569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.454816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.455556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.455812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.481135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [81.481450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [81.481707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.481981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.482045] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.482205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.482385] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.482433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.482668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.482684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.482992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.483318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.483635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.484025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.484357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.485248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.485555] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.514337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [81.514585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [81.514793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.515061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.515087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.515289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.515432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.515546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.515743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.515790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.516161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.516508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.516842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.517245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.517668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.518742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.519136] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.547871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [81.548174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [81.548290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.548376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.548591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.548649] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.548776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.548992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.548990] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.549188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [81.549461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [81.549729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [81.550070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.550345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [81.550601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [81.551361] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.551635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.580953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [81.581144] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [81.581314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.581477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.581639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.581832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.582107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.582218] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.582426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.582574] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.582693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.582877] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.582963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.583210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.583505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.584254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.584517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.614343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [81.614549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [81.614733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.614956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.615139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.615082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.615313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.615483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.615435] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.615648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.615738] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.615812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.616036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.616661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.616922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.664432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.664754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.665086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.665233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.665331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.665563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.665655] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.665802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.666059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.666183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.666498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.666801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.667184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.667500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.667883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.668715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.669072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.698020] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.698430] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.698677] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455] <7> [81.698755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.715093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [81.715403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [81.715668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.715979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.716211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.716436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.716939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.717237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.717523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.717800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.718282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.718532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.719438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.719744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.747741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.748135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.748089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.748378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.748604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.748545] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.748877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.748971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.749137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.749425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.749812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.750231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.750631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.751026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.751327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.752243] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.752604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.781305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.781613] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.781924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.782067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.782149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.782368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.782449] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.782604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.782777] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.782857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.783172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.783476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.783796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.784164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.784481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.785403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.785718] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.814254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [81.814519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [81.814736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.815004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.815148] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.815207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [81.815442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [81.815504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.815688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.815806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.816025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.816324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.816606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.816888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.817192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.817971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.818260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.847663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [81.847951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [81.848043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.848130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.848294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.848377] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.848462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.848627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.848660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.848835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.849083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.849320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.849552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.849780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.850079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.850692] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.850979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.880901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.881094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.881264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.881422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.881582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.881742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.881981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.882100] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.882227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.882413] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.882457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.882681] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.882702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.883005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.883268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.884287] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.884586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.914285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [81.914512] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [81.914704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.914950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.915080] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.915135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.915335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.915394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.915547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.915662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.915923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [81.916106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [81.916282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.916462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [81.916628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [81.916813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [81.916981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.917220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.917459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.917694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.918014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.918263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.919003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.919257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.947609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.947863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.948061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.947996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.948299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.948380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.948493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.948682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.948703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.948952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.949327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [81.949507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [81.949680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.949961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [81.950153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [81.950339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [81.950536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [81.950849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [81.951139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [81.951450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.951729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [81.952052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [81.952841] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.953127] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [81.981194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.981469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.981703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.981993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.982138] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [81.982201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.982441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.982498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [81.982679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.982831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [81.983124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.983306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.983482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.983686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.983894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.984073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.984246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.984600] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [81.984782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [81.984945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [81.985105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [81.985264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [81.985422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [81.985583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [81.985853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [81.986108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [81.986384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.986627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [81.986908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [81.988061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [81.988319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.014220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [82.014483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [82.014703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.014979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.015163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.015116] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.015391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.015452] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.015610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.015733] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.016029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [82.016201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [82.016358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.016513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.016664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.016858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.017020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.017370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [82.017531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [82.017688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.017883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.018038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.018200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.018371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [82.018643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.018947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.019213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.019474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.019807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.020571] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.020868] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.047901] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.048262] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.048507] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456] <7> [82.048548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.066428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.066948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [82.067200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [82.067398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [82.067590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.067801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.067985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [82.068200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [82.068393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.068599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.068823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [82.068999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [82.069163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.069314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.069465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.069611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.069803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.070208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.070386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [82.070518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [82.070648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [82.070867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.071014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.071137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [82.071258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [82.071373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.071486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.071599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [82.071706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [82.071856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.071963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.072068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.072171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.072279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.072449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.072615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.072781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.072958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.073119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.073722] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.073906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.080596] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [82.098990] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457] <7> [82.114780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.115153] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.115469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.118482] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.119481] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.119744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.147571] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.147958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [82.148030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.148246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [82.148489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [82.148440] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.148753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.148822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.148988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.149223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.149507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.149844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.150183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.150513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.150866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.151199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.151577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.152468] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.152827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.180907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.181187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [82.181393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [82.181580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [82.181810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.181988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.181932] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.182154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.182249] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.182342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.182512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.182545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.182877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.183139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.183398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.183653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.183997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.184715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.184965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.214162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.214441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [82.214728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [82.214930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [82.214859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.215121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.215229] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.215327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.215516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.215533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.215709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.215909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.216186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.216458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.216764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.217017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.217284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.218057] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.218301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.247696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.247834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.247935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [82.248106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [82.248166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.248267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [82.248423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.248452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.248578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.248763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.248917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.249088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.249325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.249592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.249854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.250086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.250336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.250995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.251256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.280815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.281047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [82.281260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [82.281445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [82.281601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.281861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.282027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.281976] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.282183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.282309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.282376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.282593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.282650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.282945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.283195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.283473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.283733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.284426] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.284684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.314142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.314379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [82.314562] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [82.314777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [82.314944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.314920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.315130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.315289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.315252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.315445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.315535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.315642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.315957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.316194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.316474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.316743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.316975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.317866] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.318150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.331135] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.364161] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.364432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [82.364622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [82.364885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [82.364894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.365086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.365275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.365284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.365464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.365616] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.365747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.365967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.366292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.366612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.366988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.367337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.367639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.368672] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.369033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.397602] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.398006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [82.398109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.398311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [82.398563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [82.398561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.398899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.399007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.399121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.399339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.399559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.399881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.400283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.400676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.401013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.401343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.401751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.404132] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.404463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.430881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.431180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [82.431418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [82.431611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [82.431856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.432040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.432004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.432218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.432346] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.432399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.432599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.432657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.432908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.433189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.433461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.433785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.434064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.434972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.435259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.464359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.464676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [82.464780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.464934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [82.465137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [82.465112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.465319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.465393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.465499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.465705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.465883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.466115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.466513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.466760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [82.466931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [82.467092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [82.467265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.467448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.467608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.467826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.467994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [82.468252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [82.468508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [82.468788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.469047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [82.469272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [82.469959] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.470230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.497521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.497876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [82.497873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.498086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [82.498158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.498281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [82.498417] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.498465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.498676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.498857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.499076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.499299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.499714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.499950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [82.500145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [82.500338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [82.500524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.500756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.500985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.501192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.501401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [82.501715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [82.502050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [82.502342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.502646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [82.502992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [82.503817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.504103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.533003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.533461] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.533854] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458] <7> [82.533870] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.555485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.555842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [82.556031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [82.556206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [82.556364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.556512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.556690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.556826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.556977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.557123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.557246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.557381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.557506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.557640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.557752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.557859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.557990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.558242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.558368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [82.558467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [82.558560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [82.558790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.558883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.558975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.559064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.559151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.559235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.559319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.559400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.559478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.559555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.559664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.559742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.559856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.559984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.560111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.560235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.560351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.560467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.560958] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.561080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.564966] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459] <7> [82.577474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.597453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.597734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.597819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.598027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.598064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.598225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.598350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.598415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.598681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.598875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.599116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.599357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.599852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.600102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.600303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.600502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.600801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.601009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.601247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.601464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.601725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.602058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.602379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.602723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.603095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.603405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.604252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.604592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.630938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.631270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [82.631583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [82.631804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [82.632012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.632208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.632407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.632696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.632702] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.632944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.633031] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.633264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.633326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.633576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.633874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.634216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.634513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.635378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.635703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.664251] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.664693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.664723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.665015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.665066] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.665274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.665398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.665522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.665829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.666056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.666316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.666614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.666961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.667285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.667721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.668041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.668349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.669249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.669574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.697696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.697706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.698017] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [82.698068] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.698238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [82.698371] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.698442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [82.698691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.698886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.699066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.699278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.699496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.699837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.700080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.700320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.700568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.700804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.701593] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.701861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.730756] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.731004] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [82.731230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [82.731400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [82.731606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.731779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.731752] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.731946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.732107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.732086] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.732288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.732368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.732569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.732822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.733073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.733319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.733627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.734349] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.734636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.764112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.764377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [82.764691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [82.764885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [82.764841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.765127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.765251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.765340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.765557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.765642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.765772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.765983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.766276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.766582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.766930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.767222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.767499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.768564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.768861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.781126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.814073] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.814387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.814710] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.814845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.814938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.815184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.815241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.815389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.815620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.815597] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.815814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.816034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.816340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.816670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.816962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.817254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.817608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.818341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.818694] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.847526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.847869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [82.848113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [82.848337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [82.848596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.848806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.848749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.849011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.849133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.849236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.849459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.849461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.849817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.850120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.850415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.850739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.851050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.851937] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.852245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.880822] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.881208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [82.881559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [82.881569] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.881827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [82.882028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.882117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.882384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [82.882457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.882716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [82.882997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [82.883292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.883740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.884155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.884560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.884965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.885334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.886526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.886926] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.914332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.914719] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [82.914812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.914958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [82.915167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [82.915182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.915368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.915527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.915651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.915851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [82.916033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [82.916232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [82.916510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [82.916777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [82.917032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.917264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [82.917506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [82.918234] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.918524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.947387] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [82.947662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [82.947880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [82.948063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [82.948277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.948493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [82.948707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [82.948648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.948878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [82.949015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.949085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [82.949343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.949379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [82.949728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [82.950013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.950293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [82.950603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [82.951443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.951789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.980850] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026 <7> [82.981075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [82.981272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025 <7> [82.981504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.981708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.981657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [82.981912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.982093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.982038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [82.982264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [82.982344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [82.982434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.982657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.982827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.982993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.983166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.983370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.983594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.983782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.984198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026 <7> [82.984371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [82.984585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025 <7> [82.984751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.984915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.985072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.985225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.985381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [82.985580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.985733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.985888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [82.986036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [82.986185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [82.986335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [82.986510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [82.986706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [82.986997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [82.987266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [82.987525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.987774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [82.988010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [82.988652] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [82.988897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [82.989696] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [82.989924] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [83.030728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.031010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.031270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.031626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.031722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.031929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.032163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.032132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.032421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.032518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.032969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.033209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.033426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.033706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.033926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.034175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.034394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.034915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.035162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.035368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.035742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.035958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.036192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.036481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.036809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.037112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.037400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.037784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.038071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.038803] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.039090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.064139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [83.064421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [83.064742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.064856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.064968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.065194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.065255] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.065453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.065656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.065708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.066178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [83.066398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [83.066689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.066897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.067112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.067314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.067570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.068015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [83.068220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [83.068416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.068687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.068883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.069069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.069254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.069579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.069929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.070198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.070481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.070792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.071655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.071957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.097497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.097827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.098103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.098358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.098764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.098733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.099015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.099188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.099293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.099635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.099737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.100078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.100398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.100769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.101127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.102176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.102528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.131387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [83.131699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [83.131829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.131906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.132094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.132157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.132271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.132462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.132502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.132716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.132972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.133241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.133519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.133772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.134015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.134771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.135055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.164053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [83.164308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [83.164611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.164724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.164819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.165012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.165071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.165215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.165351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.165434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.165705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.165969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.166224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.166490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.166789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.167625] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.167886] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.197379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [83.197599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [83.197756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.197921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.198095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.198265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.198491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.198612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.198754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.198944] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.199002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.199219] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.199238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.199502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.199775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.200413] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.200656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.247348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.247572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.247730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.247882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.248034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.248182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.248351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.248636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.248761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.248868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.249074] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.249098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.249339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.249368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.249645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.250229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.250590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.280714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [83.280912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [83.281104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.281288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.281535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.281732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.281662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.281937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.282044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.282215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.282347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.282509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.282825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.283079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.283327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.284061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.284323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.313960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [83.314136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [83.314294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.314543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.314699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.314679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.314852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.314990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.315024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.315277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.315286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.315556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.315855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.316100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.316342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.317164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.317427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.347574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [83.347771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [83.347946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.348144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.348301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.348586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.348631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.348801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [83.348945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.349044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [83.349226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.349298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [83.349609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.349856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [83.350088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [83.350730] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.350971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.380661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [83.380887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [83.381082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.381269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.381521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.381636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.381730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.381952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.382017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.382248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.382378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.382571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.382857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.383118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.383427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.384229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.384522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.414021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [83.414203] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [83.414425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.414598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.414554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.414767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.414931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.414911] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.415086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.415233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.415202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.415416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.415565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.416101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.416351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.464034] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [83.464277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [83.464558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.464677] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.464749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.464929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.465012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.465141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.465293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.465382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.465652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.465910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.466148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.466459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.466696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.467347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.467596] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.497499] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460] <7> [83.498392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [83.498479] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.498624] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [83.498802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.498812] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.498982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.499163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.499114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.499366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.499570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.499968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [83.500146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [83.500339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.500541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.500713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.500878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.501055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.501342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.501610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.501876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.502182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.502495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.503233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.503526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.530702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [83.530959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [83.531184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.531463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.531577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.531678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.531924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.531960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.532148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.532286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.532588] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [83.532786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [83.532972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.533190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.533405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.533584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.533771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.534045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.534320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.534604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.534860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.535105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.535942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.536208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.564236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [83.564571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [83.564717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.564807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.565024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.565098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.565234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.565479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.565557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.565799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.566228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [83.566497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [83.566693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.566906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.567084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.567258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.567560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.567965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [83.568139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [83.568332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.568532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.568709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.568872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.569050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.569362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.569659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.569952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.570217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.570531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.571371] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.571679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.597339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [83.597598] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [83.597816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.598028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.598234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.598572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.598719] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.598804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.599101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.599326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [83.599473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.599530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [83.599724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.599916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.600104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.600312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.600508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.600922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [83.601110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [83.601324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.601506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.601679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.601877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.602052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.602348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.602607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.602860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.603107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.603409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.604162] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.604413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.630703] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [83.630977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [83.631198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.631466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.631594] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.631666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.631898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.631945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.632113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.632228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.632454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.632717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.632975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.633292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.633556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.634178] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.634472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.663944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [83.664137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [83.664364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.664545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.664497] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.664726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.664852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.664935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.665148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.665148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.665446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.665698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.665945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.666209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.666480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.667170] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.667459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.697371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [83.697575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [83.697756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.697973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.698173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.698422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.698539] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.698848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.698919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.699128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.699230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.699438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.699701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.700019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.700311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.700985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.701264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.730648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [83.730857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [83.731038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.731330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.731449] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.731526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.731745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.731829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.731978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.732153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.732322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.732637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.732897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.733140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.733413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.734168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.734482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.764208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [83.764501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [83.764695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.764609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.764879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.765060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.764990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.765262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.765372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.765465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [83.765757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [83.766037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [83.766378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.766654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [83.766911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [83.767628] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.767882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.797255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [83.797442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [83.797610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.797795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.797955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [83.798113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [83.798336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [83.798398] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.798592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [83.798735] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.798846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [83.799018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.799088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.799357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [83.799627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [83.800429] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.800683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.831348] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.831741] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.832038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.832227] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461] <7> [83.833269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.833499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [83.833667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [83.833826] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [83.833991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.834188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.834432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.834592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.834747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.834897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [83.835042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [83.835181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [83.835374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.835515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.835653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.835790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.835964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.836235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.836544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.836815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.837047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.837285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.837954] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.838233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.846961] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [83.866278] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462] <7> [83.867736] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.897281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.897602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.897868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.898091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.898391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.898520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.898620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.898843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.898932] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.899114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.899321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.899434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.899823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.900154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.900539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.900907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.901243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.902114] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.902517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.930599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.930886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [83.931135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [83.931384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [83.931557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.931518] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.931755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [83.931831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.931918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [83.932081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [83.932099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.932313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.932580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.932840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.933082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.933349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [83.933579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [83.934564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.934829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.963887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.964133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [83.964429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [83.964606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [83.964555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.964776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.964889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.964975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [83.965151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [83.965194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.965369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [83.965541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [83.965782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [83.966021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [83.966288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.966600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [83.966846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [83.967564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [83.967807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [83.997414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [83.997661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [83.997838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [83.998007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [83.998201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [83.998324] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [83.998388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [83.998567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [83.998639] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [83.998727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [83.998896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [83.998908] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [83.999153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [83.999452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [83.999755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.000004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.000311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.001067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.001411] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.030547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.030820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [84.031026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [84.031311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [84.031401] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.031492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.031665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.031758] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.031871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.032050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.032057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.032260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.032628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.032823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [84.032977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [84.033134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [84.033364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.033513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.033661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.033835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.034028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.034322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.034573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.034820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.035065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.035344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.036099] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.036386] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.063959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.064329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [84.064330] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.064586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [84.064663] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.064776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [84.064960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.064945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.065204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.065379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.065570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.065754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.066109] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.066748] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [84.066920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [84.067079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [84.067267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.067421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.067571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.067747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.067931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.068202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.068464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.068773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.069049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.069319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.070019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.070315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.080721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.113861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.114188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.114296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.114462] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.114671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.114650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.114870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.114950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.115098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.115347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.115525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.115730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.116176] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.116389] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.116560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.116728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.116892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.117089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.117324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.117493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.117670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.117932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.118200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.118510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.118799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.119046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.119778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.120042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.147284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.147573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [84.147777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [84.147964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [84.148176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.148236] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.148348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.148514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.148548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.148708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.148821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.148892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.149357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.149567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [84.149773] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [84.149951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [84.150134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.150318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.150474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.150646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.150839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.151080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.151353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.151590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.151870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.152111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.153179] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.153443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.180500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.180788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [84.181042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [84.181287] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [84.181368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.181463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.181631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.181707] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.181796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.181978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.181972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.182189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.182457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.182720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.182975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.183291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.183552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.184309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.184579] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.214126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.214274] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.214402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [84.214604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [84.214630] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.214791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [84.214974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.214934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.215184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.215355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.215556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.215761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [84.216072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [84.216351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [84.216637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.216886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [84.217144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [84.217911] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.218186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.247173] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.247422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [84.247607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [84.247783] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [84.247958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.248175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.248354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.248331] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.248554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.248686] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.248745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [84.248987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.249014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [84.249296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [84.249589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.249833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [84.250064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [84.250771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.251013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.300215] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.300367] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.300461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.300952] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463] <7> [84.301577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.301678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [84.301743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [84.301802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [84.301858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.301915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.301970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.302024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.302120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.302177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.302234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.302288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.302341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.302395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.302445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.302494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.302570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.302654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.302735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.302816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.302896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.302976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.303282] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.303378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.315549] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464] <7> [84.316474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.347267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.347668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.347977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.348395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.348508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.348700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.348980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.349002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.349333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.349503] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.349605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.349942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.350388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.350785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.351274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.351662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.352049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.353041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.353467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.380660] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.381050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [84.381452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [84.381598] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.381700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [84.381936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.382010] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.382200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.382455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.382424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.382670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.382913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.383280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.383607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.383933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.384313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.384667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.385820] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.386166] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.413877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.414298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.414362] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.414577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.414813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.414770] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.415036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.415184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.415384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.415609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.415872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.416184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.416517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.416843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.417194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.417484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.417770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.418599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.418903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.447468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.447796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [84.448104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [84.448227] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.448317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [84.448521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.448587] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.448719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.448912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.448889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.449192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.449404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.449667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.449932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.450240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.450510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.450776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.451599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.451903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.480447] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.480738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [84.480992] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [84.481262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [84.481339] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.481437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.481604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.481653] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.481770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.481927] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.481961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.482631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.482901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.483184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.483428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.483666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.483946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.484711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.484978] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.513838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.514114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [84.514189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.514318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [84.514488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [84.514523] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.514655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.514816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.514803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.514978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.515177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.515353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.515596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.515834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.516094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.516399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.516653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.517358] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.517603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.530796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.563838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.564114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.564217] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.564299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.564476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.564551] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.564646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.564812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.564833] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.564978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.565238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.565438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.565800] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.566041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.566202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.566358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.566546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.566720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.566883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.567065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.567223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.567462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.567699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.567932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.568189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.568418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.569017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.569271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.597305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.597597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [84.597804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [84.597988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [84.598228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.598398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.598367] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.598565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.598684] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.598738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.598922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.598955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.599321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.599531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [84.599699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [84.599862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [84.600039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.600190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.600343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.600491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.600645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.600888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.601179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.601434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.601732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.601973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.602955] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.603266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.630498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.630813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.631083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.631173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.631279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.631462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.631514] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.631642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.631816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.631797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.632051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.632274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.632718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.632928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [84.633179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [84.633346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [84.633507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.633701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.633868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.634061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.634219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.634464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.634701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.634959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.635251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.635548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.636255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.636506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.664050] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.664136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.664335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [84.664451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.664567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [84.664746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [84.664721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.664915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.665135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.665321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.665504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.665701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.666159] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.666370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [84.666538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [84.666701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [84.666863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.667063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.667229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.667389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.667555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [84.667815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [84.668110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [84.668366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.668668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [84.668911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [84.669655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.669926] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.697125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [84.697418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [84.697656] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [84.697847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [84.698105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.698179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.698280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.698447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.698493] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.698621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.698759] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.698803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [84.699087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [84.699354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [84.699616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.699871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [84.700158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [84.700939] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.701251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.730504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [84.730696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [84.730861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [84.731072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.731245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.731198] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.731422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.731527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.731587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.731751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [84.731808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.731905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [84.732101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [84.732259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [84.732430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.732575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.732719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.732863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.733081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.733343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.733597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.733905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.734170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.734401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.735115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.735374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.736051] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [84.736258] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [84.763880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.764240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.764379] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.764494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.764728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.764791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.764982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.765197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.765257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.765518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.765850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.766227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.766548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.766860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.767216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.768053] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.768356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.798763] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465] <7> [84.798620] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.799030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.799333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.799579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [84.799798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [84.800050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.800260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.800467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.800713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.800999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.801304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.801597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.801886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.802249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.802526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.803264] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.803546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.830469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.830725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.830980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.831170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.831110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.831353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.831442] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.831566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.831726] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.831788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.832082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.832331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.832572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.832807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.833136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.833910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.834215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.864031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [84.864067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.864217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [84.864383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.864382] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.864543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.864650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.864703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [84.864858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [84.865081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.865379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.865634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.865881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.866153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.866384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.867017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.867260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.897073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [84.897243] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [84.897402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.897586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [84.897741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [84.897891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [84.898170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.898474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.898503] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.898734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.898785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.898995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.899232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.899460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.899739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.900458] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.900716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.930433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [84.930657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [84.930845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.931082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.931152] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.931263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.931463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.931465] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.931675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.931729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.931975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.932222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.932461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.932698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.932949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [84.933612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.933880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.963734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [84.963973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [84.964145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.964102] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.964344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [84.964436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.964531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [84.964732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [84.964719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.964963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [84.965207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [84.965445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [84.965677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.965918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [84.966193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [84.966794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [84.967074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [84.997118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [84.997314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [84.997477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [84.997670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [84.997855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [84.998115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [84.998151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [84.998307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [84.998482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [84.998561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [84.998768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [84.998811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [84.999106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.999350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [84.999587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.000272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.000526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.030349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [85.030538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [85.030696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.030930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.031105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.031072] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.031268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.031405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.031450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.031690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.031702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.031970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.032218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.032458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.032745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.033486] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.033746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.063953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [85.064017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.064150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [85.064319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.064353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.064480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.064639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.064638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.064794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.065004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.065360] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [85.065519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [85.065672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.065820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.066065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.066224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.066379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [85.066624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [85.066896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [85.067143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.067405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [85.067663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [85.068308] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.068578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.097155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [85.097401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [85.097602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.097790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.098031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.098212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.098173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.098453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.098504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.098786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.098844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [85.099077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [85.099246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.099410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.099574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.099733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.099923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.100169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.100406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.100640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.100914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.101186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.101926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.102193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.130402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [85.130648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [85.130885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.131071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.131025] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.131245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.131339] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.131441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.131605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.131608] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.131764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.131965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.132148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.132473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [85.132638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [85.132798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.133024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.133183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.133330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.133477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.133618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.133760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.133939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.134205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [85.134364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [85.134520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.134701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.134870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.135013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.135153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.135291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.135430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.135569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.136196] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.136459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.180420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.180668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.180919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.181115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.181051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.181303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.181388] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.181514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.181672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.181718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.182165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.182376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.182547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.182715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.182913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.183092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.183279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.183631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.183795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.183999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.184148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.184297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.184440] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.184591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.184831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.185132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.185436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.185683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.186014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.186709] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.187010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.213996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.214338] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.214604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.215303] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466] <7> [85.216187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [85.216421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [85.216629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.216823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.217070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.217257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.217511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.217788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.218172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.218437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.218694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.219038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.219752] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.220054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.247127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.247379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.247595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.247795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.248056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.248201] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.248254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.248477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.248535] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.248745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.248817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.249034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.249277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.249540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.249775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.250612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.250893] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.280517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [85.280714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [85.280944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.281083] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.281157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.281339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.281415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.281507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.281696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.281698] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.282000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.282257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.282508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.282753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.283072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.283698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.283969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.313663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [85.313883] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [85.313927] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.314038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.314206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.314240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.314355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.314506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.314505] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.314890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.315195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.315452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.315703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.315980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.316225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.317014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.317278] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.347077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [85.347280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [85.347457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.347632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.347841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.348020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.347997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.348260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.348333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.348527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.348615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.348778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.349069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.349312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.349549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.350233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.350495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.380311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.380494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.380648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.380835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.381009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.380971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.381192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.381304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.381378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.381587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.381631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.381934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.382206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.382465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.382751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.383459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.383754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.413693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [85.413915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [85.414076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.414053] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.414232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.414384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.414367] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.414533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.414631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.414702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.414964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.415211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.415474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.415721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.415994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.416674] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.416961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.446990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [85.447162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [85.447318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.447476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.447634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.447822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.447854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.447998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.448129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.448234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.448371] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.448464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.448734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.449014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.449271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.450029] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.450302] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.480474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [85.480651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [85.480850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.480856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.481019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.481130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.481221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.481377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.481385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.481557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [85.481822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [85.482111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [85.482380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.482663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [85.482956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [85.483715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.484057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.513649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [85.513895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [85.514080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.514023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.514300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.514406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.514492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.514704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.514736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.514968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [85.515282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [85.515589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [85.515928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.516214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [85.516486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [85.517279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.517547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.552182] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.552645] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.553106] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467] <7> [85.553113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.554858] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.555260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [85.555601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [85.555947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [85.556212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.556452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.556690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.556986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.557248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.557475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [85.557681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [85.557940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [85.558151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.558389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.558581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.558793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.559014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.559304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.559585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.559898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.560149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.560377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.561254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.561484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.563439] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [85.582015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468] <7> [85.583158] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.613630] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.613930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.614140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.614339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.614531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.614718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.614975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.615163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.615131] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.615396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.615463] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.615773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.615844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.616071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.616246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.616413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.616577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.616759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.616920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.617086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.617264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.617523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.617794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.618052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.618319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.618583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.619411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.619678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.647111] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.647379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [85.647573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [85.647799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [85.647974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.647919] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.648150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.648243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.648326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.648536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.648526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.648817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.649175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.649373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [85.649531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [85.649685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [85.649883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.650078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.650260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.650416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.650583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.650874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.651152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.651424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.651692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.652027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.652893] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.653188] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.680327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.680610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.680871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.681062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.681018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.681246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.681422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.681378] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.681600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.681660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.681863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.682493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.682883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.683098] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.683272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.683445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.683610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.683820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.683989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.684154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.684323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.684585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.684876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.685188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.685437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.685756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.686522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.686822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.713860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.714189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [85.714411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [85.714617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [85.714930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.714902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.715115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.715292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.715363] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.715490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.715684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.715728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.716167] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.716376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [85.716571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [85.716761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [85.716922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.717080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.717239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.717394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.717558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.717840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.718095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.718348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.718599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.718884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.719674] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.719991] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.746986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.747320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [85.747544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [85.747873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [85.747825] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.748068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.748165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.748254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.748434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.748450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.748635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.748880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.749353] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.749582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [85.749802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [85.749990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [85.750181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.750371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.750597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.750828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.751050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.751376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.751713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.752086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.752428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.752743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.753648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.753983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.780497] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.781004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.781041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [85.781378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [85.781427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.781663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [85.781855] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.782094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.782386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.782627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.782985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.783241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.783573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.783933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.784341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.784698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.785040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.786233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.786580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.797405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.830277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.830611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.831022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.831119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.831265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.831499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.831528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.831762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.831933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.832040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.832259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.832506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.832873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.833253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.833577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.833938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.834339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.835232] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.835574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.863629] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.863941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [85.864152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [85.864340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [85.864519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.864754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [85.864788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.864934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [85.865115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [85.865088] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.865356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.865322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.865638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.865971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.866247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.866519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.866862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.867681] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.867979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.896900] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.897164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [85.897386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [85.897571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [85.897806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.897998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [85.897944] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.898191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [85.898327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.898424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [85.898674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.898678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.898973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.899248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.899515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.899870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.900172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.900937] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.901236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.930401] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.930662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [85.930843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [85.931009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [85.931175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.931361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.931529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [85.931714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [85.931850] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.931909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [85.932192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.932204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [85.932457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [85.932477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.932724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.932985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [85.933279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [85.934005] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.934306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [85.963919] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [85.964249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [85.964439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [85.964612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [85.964856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [85.964974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [85.965169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [85.965159] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [85.965326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [85.965405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [85.965487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [85.965692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [85.965908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [85.966113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [85.966308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.966525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [85.966741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [85.967476] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [85.967668] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.000170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.000759] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.001387] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469] <7> [86.001264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.004156] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.004586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [86.005181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [86.005453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [86.005739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.005984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.006273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.006499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.006801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.006996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.007223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.007431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.007653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.007835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.008003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.008159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.008342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.008585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.008997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.009224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.009428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.009638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.010405] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.010604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.015199] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470] <7> [86.016375] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.047071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.047528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [86.048036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [86.048186] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.048368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [86.048772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.048772] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.049088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.049261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.049400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.049777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.050123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.050575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.051067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.051484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.051917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.052336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.053321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.053751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.080267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.080550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [86.080844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [86.081029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [86.080980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.081203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.081292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.081399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.081557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.081581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.081827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.082019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.082283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.082543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.082846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.083084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.083319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.084030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.084293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.113567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.113870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [86.114088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [86.114270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [86.114446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.114671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.114801] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.114890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.115057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.115144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.115240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.115427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.115633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.115870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [86.116059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [86.116226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [86.116389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.116550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.116769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.116932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.117101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.117376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.117660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.117974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.118258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.118537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.119361] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.119656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.147250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.147645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [86.147755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.147913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [86.148141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [86.148152] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.148358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.148477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.148566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.148841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.149030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.149286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.149724] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.149989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [86.150191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [86.150366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [86.150540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.150770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.150990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.151198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.151389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.151707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.152002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.152321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.152610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.152877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.153746] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.154015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.180357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.180758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [86.180854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.181063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [86.181300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [86.181283] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.181528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.181676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.181806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.182023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.182266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.182488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.182954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.183198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [86.183391] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [86.183577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [86.183830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.184012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.184221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.184399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.184601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.184901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.185199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.185492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.185865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.186136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.186925] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.187193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.213668] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.214070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [86.214371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [86.214655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [86.214802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.214886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.215155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.215215] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.215380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.215614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.215568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.215857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.216408] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.216700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [86.216946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [86.217152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [86.217353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.217550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.217855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.218054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.218263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.218596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.218947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.219241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.219528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.219859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.220934] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.221227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.230327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.263538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.263881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [86.264091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [86.264286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [86.264474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.264704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.264889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.264845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.265093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.265165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.265315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.265435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.265582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.265831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.266078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.266338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.266772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.267512] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.267844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.296842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.297083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [86.297301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [86.297481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [86.297706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.297884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.297830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.298080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.298146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.298255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.298410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.298435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.298706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.298949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.299201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.299502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.299781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.300515] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.300841] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.330152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.330379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [86.330632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [86.330804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [86.330789] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.330976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.331148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.331129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.331321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.331435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.331492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.331759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.332092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.332401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.332700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.332962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.333225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.334012] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.334269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.363731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.363973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [86.364160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [86.364323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [86.364486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.364813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.364821] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.364982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.365170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.365151] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.365381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [86.365447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.365642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.365879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.366121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.366367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.366644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.367340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.367600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.396786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [86.397009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [86.397213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [86.397399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [86.397596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.397756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.397725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.397949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.398119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.398058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.398293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [86.398341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.398568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [86.398818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [86.399054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.399284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [86.399622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [86.400282] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.400556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.430293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [86.430470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [86.430696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [86.430859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.430838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.431015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.431178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.431161] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.431373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.431441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.431647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [86.431813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [86.431969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [86.432117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [86.432258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.432396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.432553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.432723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.432919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.433190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.433445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.433729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.434028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.434298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.435047] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.435305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.436053] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [86.436260] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [86.463567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.463791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.463980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.464164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.464346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.464578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.464584] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.464782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.464920] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.465062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.465221] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.465342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.465645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.465920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.466199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.466923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.467208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.497761] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471] <7> [86.497606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.498028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.498410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.521745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [86.521994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [86.522194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.522374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.522628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.522796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.523021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.523260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.523475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.523713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.523909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.524101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.524835] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.525022] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.546898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.547134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.547342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.547606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.547615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.547815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.547996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.548052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.548285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.548299] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.548566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.548825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.549098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.549375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.549719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.550549] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.550840] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.580570] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [86.580656] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.580859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [86.581118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.581142] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.581371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.581581] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.581663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.581902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.582232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.582623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.582960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.583350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.583731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.584066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.584968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.585324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.613531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [86.613792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [86.614009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.614223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.614435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.614740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.614876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.614975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.615254] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.615285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.615621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.615613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.615954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.616224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.616516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.617311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.617623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.646842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [86.647026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [86.647202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.647371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.647590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.647782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.647742] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.647977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.648064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.648314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [86.648329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.648487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [86.648640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.648818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.648985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.649151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.649305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.649570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.649804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.650035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.650264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.650507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.651088] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.651326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.680183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.680385] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.680627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.680669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.680809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.681024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.681026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.681197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.681333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.681389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.681826] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.682032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.682209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.682372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.682575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.682733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.682899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.683167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.683432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.683748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.684040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.684320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.685108] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.685388] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.713586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [86.713862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [86.714078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.714283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.714521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.714653] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.714715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.714974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.715008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.715343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.715396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [86.715671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [86.715855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.716034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.716213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.716425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.716682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.717097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [86.717263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [86.717420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.717634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.717792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.717981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.718157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.718408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.718689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.718928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.719170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.719433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.720186] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.720435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.746845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.747118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.747353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.747647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.747775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.747864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.748115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.748158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.748378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.748517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.748882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.749084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.749278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.749491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.749679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.749885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.750078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.750513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [86.750704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [86.750888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.751065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.751243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.751419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.751673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.751965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.752238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.752525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.752844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.753099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.753881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.754135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.780333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [86.780626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [86.780758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.780832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.781016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.781084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.781194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [86.781351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.781399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [86.781664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [86.781938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [86.782200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [86.782466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.782769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [86.783017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [86.783703] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.783955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.813496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [86.813747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [86.813969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.814183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.814394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.814679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.814834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.814921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.815246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.815245] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.815615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.815646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.815949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.816245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.816554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.817367] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.817707] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.846821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [86.847014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [86.847199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.847451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [86.847630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [86.847597] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.847804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [86.847974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.847951] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.848138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.848302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.848270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.848502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.849206] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.849501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.896971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.897328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.897676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.897914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.897828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.898141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.898247] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.898371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.898656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.898738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.899103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.899445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.899764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.900082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.900462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.901390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.901775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.930484] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.930887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.931197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.932586] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472] <7> [86.947894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [86.948138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [86.948342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.948626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [86.948819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [86.949024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [86.949224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [86.949500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [86.949743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [86.949982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.950237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [86.950660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [86.951333] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.951592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [86.980208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [86.980511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [86.980617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [86.980719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [86.980926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [86.981002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [86.981135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [86.981344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [86.981354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [86.981647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [86.981966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [86.982301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [86.982734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.983087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [86.983474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [86.984562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [86.984912] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.013694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [87.013908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [87.014110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.014337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.014619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.014779] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.014874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.015152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [87.015209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.015529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [87.015649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.015868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [87.016178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.016508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.016807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [87.017648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.017967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.046756] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [87.047013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [87.047216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.047458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.047646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.047595] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.047853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.047929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.048047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [87.048208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.048295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.048572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.048813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.049059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.049318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.050048] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.050296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.080110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [87.080306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [87.080549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.080734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.080680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.080917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.081033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.081122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.081314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.081326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [87.081663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [87.081920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [87.082166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.082422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.082687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [87.083239] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.083533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.113419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [87.113623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [87.113806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.113987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.114173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.114430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.114562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.114646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [87.114937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.114946] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.115202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.115267] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.115605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.115877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.116119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.116724] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.116982] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.146726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [87.146904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [87.147065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.147227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.147431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.147597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.147578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.147786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [87.147909] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.148033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [87.148206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.148287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [87.148562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.148803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.149041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [87.149699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.149950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.180079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [87.180283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [87.180541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.180676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.180771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.180961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.181055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.181139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.181354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [87.181410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.181643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.181949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.182259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.182660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.182970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.183779] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.184066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.213705] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [87.213925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [87.214147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.214412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.214633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.214553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.214850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.215002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.215146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [87.215429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.215702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [87.215949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [87.216153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.216353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.216538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.216718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.216941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [87.217255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [87.217608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [87.217919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.218259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [87.218628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [87.219527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.219850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.246830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [87.247117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [87.247396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.247515] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.247617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.247832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.247896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.248081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.248220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.248317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [87.248818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [87.249023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [87.249217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.249497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.249687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.249870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.250063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [87.250373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.250715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.251002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.251289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.251655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.252513] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.252829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.280471] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.280884] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.281126] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473] <7> [87.281236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.306654] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.307014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [87.307341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [87.307560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [87.307769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.307969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.308162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [87.308543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [87.308710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.308870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.309052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [87.309201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [87.309375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.309517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.309652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.309802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.309967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.310268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.310452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [87.310573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [87.310689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [87.310798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.310909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.311021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [87.311132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [87.311238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.311363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.311462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [87.311560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [87.311655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.311746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.311836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.311927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.312023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.312182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.312339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.312506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.312667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.312804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.313401] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.313542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.329769] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [87.369338] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.369499] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.369617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.369753] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474] <7> [87.379732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.380270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.380437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.413627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.414215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [87.414953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [87.414988] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.415420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [87.415701] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.415772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.416156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.416225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.416554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.416907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.417298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.418069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.418425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [87.418687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [87.418937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [87.419174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.419499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.419788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.420044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.420335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.420663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.420985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.421352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.421697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.422004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.422738] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.423002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.446848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.447256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [87.447702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [87.447845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.447964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [87.448193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.448271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.448556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.448693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.448794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.449011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.449295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.449655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.450007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.450437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.450814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.451154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.452207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.452564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.480063] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.480438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [87.480546] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.480729] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [87.480947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [87.480929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.481148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.481263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.481372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.481558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.481786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.482022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.482322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.482584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.482837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.483126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.483391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.484128] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.484442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.513551] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.513803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [87.513990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [87.514180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [87.514425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.514618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.514567] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.514849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.514948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.515061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.515349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.515359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.515680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.515995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.516317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.516604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.516884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.517802] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.518121] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.546631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.546914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [87.547151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [87.547377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [87.547550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.547535] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.547749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.547846] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.547912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.548072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.548117] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.548281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.548548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.548808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.549136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.549442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.549761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.550578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.550881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.580037] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.580376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [87.580456] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.580602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [87.580814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [87.580864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.581018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.581229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.581204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.581491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.581678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.581905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.582182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.582484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.582750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.583007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.583264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.584157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.584450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.596901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.629956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.630196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [87.630498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [87.630527] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.630672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [87.630842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.630857] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.631013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.631152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.631222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.631454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.631652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.631925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.632213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.632529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.632851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.633110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.633828] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.634102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.663347] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.663601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [87.663793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [87.663976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [87.664197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.664450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.664635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.664582] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.664816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.664939] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.665021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.665272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.665676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.665923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.666155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.666431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.666657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.667393] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.667657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.696586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.696832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [87.697058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [87.697343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [87.697418] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.697536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.697749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.697773] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.697926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.698066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.698122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.698360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.698662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.698912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.699204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.699491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.699782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.700503] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.700781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.730189] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.730535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [87.730609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.730770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [87.730952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [87.730962] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.731124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.731328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.731301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.731496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.731700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.731913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [87.732185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [87.732501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [87.732812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.733073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [87.733363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [87.734067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.734382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.763412] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.763666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [87.763861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [87.764048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [87.764312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.764496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.764439] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.764702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.764798] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.764892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.765082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [87.765102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.765385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [87.765676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [87.765954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.766223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [87.766480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [87.767335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.767618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.797352] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.797806] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475] <7> [87.797767] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.798129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.822071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.822368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [87.822552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [87.822711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [87.822868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.823022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.823170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.823450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.823592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.823746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.823875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.823995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.824112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.824246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.824355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.824455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.824575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.824819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.824966] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [87.825081] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [87.825178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [87.825318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.825409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.825494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.825575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.825657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.825738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.825820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.825899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.825976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.826052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.826127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.826218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.826295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.826418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.826535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.826652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.826765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.826876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.828515] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.828645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.830907] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476] <7> [87.843511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.863403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.863669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.863863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.864047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.864317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.864276] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.864499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.864575] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.864663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.864820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.864826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.864992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.865336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.865524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.865662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.865796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.865928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.866080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.866257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.866388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.866542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.866750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.866943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.867126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.867327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.867498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.867970] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.868163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.896701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.897060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [87.897374] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.897424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [87.897650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [87.897698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.897872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.897996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.898098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.898372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.898608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.898879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.899458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.899723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [87.899957] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [87.900201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [87.900422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.900639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [87.900855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [87.901066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [87.901326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.901651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.901973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.902311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.902600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.902887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.903691] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.903957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.929987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.930348] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.930368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.930655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.930660] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.930874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.930938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.931083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.931423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.931625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.931870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.932095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.932648] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.932892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [87.933105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [87.933349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [87.933534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.933738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [87.933917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [87.934095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [87.934335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.934664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.934965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.935285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.935588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [87.935877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [87.936675] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.936971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.963595] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.963926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [87.964241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [87.964314] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.964487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [87.964725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.964732] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.964973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.965090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.965219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [87.965443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [87.965745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [87.966066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [87.966405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [87.966736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.967029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [87.967355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [87.968176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [87.968479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [87.996679] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [87.997042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [87.997412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [87.997658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [87.997745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [87.997890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [87.998116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [87.998173] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [87.998400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [87.998531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [87.998620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [87.998921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [87.999287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [87.999620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [87.999945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.000282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.000591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [88.001557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.001915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.030017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.030390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [88.030483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.030645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [88.030866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [88.030863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.031077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.031239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.031329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [88.031536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [88.031724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [88.031935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [88.032229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [88.032510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [88.032780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.033100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [88.034294] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.034560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.046992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.079934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.080279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [88.080282] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.080557] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [88.080664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.080763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [88.080963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.080989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.081237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [88.081433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [88.081651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [88.081856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [88.082145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [88.082427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [88.082682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.082930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.083182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [88.083833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.084087] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.113361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.113659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [88.113933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [88.114178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [88.114376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.114312] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.114569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [88.114691] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.114759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [88.114984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [88.115013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.115250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [88.115534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [88.115804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [88.116064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.116349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.116590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [88.117378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.117656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.146552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.146823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [88.147071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [88.147353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [88.147450] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.147547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.147758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [88.147833] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.147950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [88.148171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [88.148198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.148406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [88.148723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [88.149032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [88.149367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.149667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.149961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [88.150852] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.151158] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.180164] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.180180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.180428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [88.180561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.180672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [88.180866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [88.180888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.181050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.181260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [88.181432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [88.181599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [88.181791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [88.182059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [88.182346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [88.182615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.182864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [88.183093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [88.183883] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.184162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.213223] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.213471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [88.213658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [88.213841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [88.214056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.214309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [88.214492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [88.214445] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.214667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [88.214825] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.214864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [88.215150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [88.215176] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.215419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [88.215681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.215942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [88.216275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [88.216970] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.217243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.246561] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [88.246923] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [88.247285] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [88.247420] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.247657] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [88.247831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.247975] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [88.248237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [88.248405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [88.248748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [88.249085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [88.249459] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [88.249824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [88.250195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [88.250494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [88.250830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [88.251161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [88.251535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [88.251856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [88.252251] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [88.252601] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7> [88.252911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [88.253235] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [88.253524] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7> [88.253811] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [88.254131] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [88.254445] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [88.254757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [88.255071] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [88.255442] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [88.255722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [88.255989] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [88.256289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [88.256573] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [88.256819] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [88.257064] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [88.257344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [88.257580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [88.257801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [88.258016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [88.258246] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [88.258444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [88.258644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [88.258830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [88.259014] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [88.259218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [88.259391] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [88.259561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [88.259724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [88.259883] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [88.260035] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [88.260214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [88.260361] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [88.260530] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [88.260683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [88.260820] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [88.260957] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261366] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [88.261492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [88.261631] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [88.261991] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [88.262116] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [88.262231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes <7> [88.262342] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [88.262450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0 <7> [88.262555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no <7> [88.262660] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [88.262762] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes <7> [88.262865] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [88.262971] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0 <7> [88.263118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [88.263238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [88.263404] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1 <7> [88.263553] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on <7> [88.263687] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [88.279690] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [88.280935] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [88.281071] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [88.283548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0 <7> [88.283657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [88.283751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0 <7> [88.283845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [88.283938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [88.284347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [88.284716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [88.284977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [88.285118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [88.285248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [88.285370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [88.285488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [88.285601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [88.285934] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <6> [88.300219] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS <7> [88.300953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7> [88.301144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [88.301279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [88.301406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7> [88.301530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <7> [88.301667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1 <7> [88.301845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [88.302007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [88.302183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [88.302331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [88.302475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [88.312965] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [88.314640] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [88.314913] [IGT] kms_rotation_crc: exiting, ret=0 <6> [88.330662] Console: switching to colour frame buffer device 180x56 <7> [88.365219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [88.365677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [88.366100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<6> [77.524783] Console: switching to colour dummy device 80x25

<6> [77.524852] [IGT] kms_rotation_crc: executing

<7> [77.530497] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [77.530507] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [77.530667] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [77.530758] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [77.530967] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [77.530970] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [77.531080] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [77.531161] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [77.531804] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [77.531808] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [77.531937] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [77.532032] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<7> [77.532318] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]

<7> [77.532321] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]

<7> [77.532782] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00

<7> [77.533091] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000

<7> [77.533194] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [77.533301] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [77.533425] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz

<5> [77.533431] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [77.533432] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [77.533434] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00

<7> [77.533436] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<5> [77.533438] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [77.533440] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor

<5> [77.533442] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [77.533443] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0

<5> [77.533445] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [77.533458] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes

<7> [77.533564] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [77.533650] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<5> [77.534152] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [77.534154] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [77.534155] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [77.534210] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:

<7> [77.534213] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [77.534217] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [77.534229] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [77.534232] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [77.534489] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [77.534499] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [77.534502] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [77.534628] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [77.534636] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [77.534638] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [77.534748] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<6> [77.534846] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top

<7> [77.536187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0

<7> [77.536255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [77.536333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [77.536408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [77.536481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [77.536573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [77.536666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [77.536749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [77.536829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [77.536909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [77.536989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [77.537268] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.537447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.537608] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<7> [77.565157] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [77.565440] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [77.565621] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [77.565726] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [77.565815] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [77.565903] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation

<7> [77.565979] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [77.566068] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [77.566182] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [77.566309] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [77.566415] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [77.566516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [77.566602] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [77.566688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [77.566772] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [77.566855] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [77.566938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [77.567019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [77.567101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [77.567180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [77.567258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [77.567352] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [77.567438] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8

<7> [77.567523] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [77.567607] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [77.567686] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [77.567759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [77.567833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [77.567905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [77.567977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [77.568049] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [77.568121] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [77.568193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [77.568265] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [77.568357] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [77.568436] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [77.568513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [77.568590] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [77.568668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [77.568747] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [77.568815] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [77.568884] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [77.568954] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [77.569023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [77.569105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [77.569174] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [77.569243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [77.569326] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [77.569406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [77.569495] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [77.569585] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [77.569675] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [77.569749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [77.569821] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [77.569892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [77.569963] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570173] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [77.570242] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [77.570325] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570401] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570477] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [77.570552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [77.570627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [77.581878] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [77.581994] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [77.602341] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.602713] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.603013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.621831] xe 0000:00:02.0: [drm:intel_dp_dump_link_status [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] ln0_1:0x77 ln2_3:0x77 align:0x80 sink:0x1 adj_req0_1:0x0 adj_req2_3:0x0

<7> [77.622316] xe 0000:00:02.0: [drm:intel_dp_link_ok [xe]] [ENCODER:390:DDI A/PHY A] 8b/10b link not ok, retraining

<7> [77.634737] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]

<7> [77.636103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [77.636540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [77.636847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.637131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.637468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.637802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.638127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.638477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.638737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.639017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.639345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.639942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [77.640222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [77.640541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.640794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.641039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.641730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.641989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.642222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.642549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.642789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.643319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.643921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [77.644218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [77.644563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.644825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.645075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.645429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.645670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.645903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.646119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.646379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.647724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.648008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.648284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.648593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.648833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.649066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.649809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.650047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.650708] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [77.650883] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [77.664638] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1

<7> [77.667263] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]

<7> [77.699279] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.699783] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.700213] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.701015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]

<7> [77.701959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [77.702321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [77.702619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.702905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.703188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.703596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.703919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.704334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.704729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.705126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.705554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.705941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.706413] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz

<7> [77.707397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.707795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.732337] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]

<7> [77.732255] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.732483] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.732617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.732980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [77.733234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [77.733324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.733406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.733488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.733564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.733650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.733762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.733871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.733972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.734061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.734150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.734876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.734999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.765246] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.765415] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]

<7> [77.765470] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.765594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.766020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [77.766167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [77.766275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.766341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.766405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.766468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.766549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.766646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.766741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.766830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.766910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.766989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.767810] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.767913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.799368] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]

<7> [77.799287] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.799634] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.799928] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.816825] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [77.817085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [77.817350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.817553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.817749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [77.817980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [77.818270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.818578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.818843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.819153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.819463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.819697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.820390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.820629] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.848552] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]

<7> [77.850237] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.850687] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.851040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.865688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [77.865983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [77.866269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.866511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [77.866749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [77.867039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [77.867710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.868062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.868441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.868775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.869087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.869470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.870558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.870881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.898734] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]

<7> [77.899234] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.899680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [77.899807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.900078] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [77.900289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.900469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.900763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.901051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.901403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.901717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.902123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.902587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.903034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.903459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.903882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.905065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.905512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.916002] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437]

<7> [77.949196] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]

<7> [77.949298] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.949726] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.949912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [77.950080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.950256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [77.950519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.950766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [77.951004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [77.951299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [77.951565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [77.951906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [77.952265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [77.952645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.953025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [77.953380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [77.954236] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.954582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [77.982213] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]

<7> [77.982162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [77.982554] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [77.982878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [77.982945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [77.983220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [77.983443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [77.983649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [77.983850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [77.984070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [77.984341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [77.984616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [77.984878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [77.985148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.985401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [77.985649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [77.986402] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [77.986675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.015171] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.015560] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.015873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.018431] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]

<7> [78.019237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [78.019446] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [78.019624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.019796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.020005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.020259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.020465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.020729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.020981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.021252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.021488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.021771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.022608] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.022887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.049061] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441]

<7> [78.049232] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.049671] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.050038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.071765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [78.071973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [78.072154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.072291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.072423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.072561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.072726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [78.072901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [78.073074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [78.073252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.073400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [78.073543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [78.074025] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.074200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.098949] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442]

<7> [78.099136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.099559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.100988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.118637] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [78.118978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [78.119332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.119583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.119822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.120123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.120387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.120729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.121043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.121439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.121741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.122011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.122936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.123325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.148337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [78.148615] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [78.148851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.149126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.149137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.149364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.149605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.149576] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.149825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.149937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.150059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.150366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.150595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.151015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [78.151444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [78.151723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.151954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.152218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.152432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.152639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.152844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.153051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.153338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.154142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.154510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.198362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.198633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.198849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.199048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.199378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.199492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.199633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.199875] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.199880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.200251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.200344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.200550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.200750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.200959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.201174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.201354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.201541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.201867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.202157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.202423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.202713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.202975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.203827] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.204141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.255801] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443]

<7> [78.255788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.255923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.256018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.256398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [78.256476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [78.256540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.256599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.256655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.256709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.256773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.256909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [78.256969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [78.257022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.257095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.257150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.257210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.257278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.257425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [78.257481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [78.257529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.257577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.257624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.257671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.257720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.257801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.257883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.257963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.258047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.258146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.258506] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.258610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.281432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.281617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.281787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.281970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.282182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.282337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.282312] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.282517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.282628] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.282831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.282882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.282975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.283155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.283297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.283433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.283571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.283712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.284007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.284198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.284322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.284442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.284556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.284667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.284782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.284966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.285171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.285349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.285518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.285682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.286269] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.286456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.315173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.315346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [78.315673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [78.315718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.315973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.316258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.316352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.316641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.316970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.317392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.317826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.318344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.318764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.319281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.319723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.320737] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.321237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.348205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [78.348505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [78.348757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.348991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.349321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.349435] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.349567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.349871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.349883] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.350308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.350324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.350667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.351063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.351451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.351784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.352868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.353265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.381564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [78.381865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [78.382198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.382323] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.382434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.382664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.382737] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.382941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.383120] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.383236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.383596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.383897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.384241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.384606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.384906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.385789] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.386096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.414829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.415117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.415219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.415328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.415534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.415632] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.415745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.416052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.416031] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.416317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.416639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.417011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.417333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.417679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.417981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.418845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.419211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.448198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [78.448439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [78.448641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.448881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.449161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.449258] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.449375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.449606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.449673] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.449991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.450054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.450284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.450566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.450866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.451179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.451967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.452326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.481479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [78.481717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [78.481937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.482221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.482269] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.482436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.482683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.482683] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.482937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.483084] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.483355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.483690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.484109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.484511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.484868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.486053] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.486468] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.515067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [78.515089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.515276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [78.515455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.515445] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.515627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.515797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.515748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.516002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.516715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [78.517033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [78.517325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [78.517622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.517902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [78.518222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [78.519126] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.519407] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.548124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [78.548336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [78.548527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.548753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.548979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.549165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.549131] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.549372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [78.549513] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.549687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [78.549839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.549997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [78.550281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.550567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [78.550877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [78.551727] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.552016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.580151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.580504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.581465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.581779] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [78.581780] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [78.581970] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [78.584784] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444]

<7> [78.586063] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.586363] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [78.586599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [78.586804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [78.587047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.587245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.587452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.587641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.587827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.588037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [78.588210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [78.588376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [78.588539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.588699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.588860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.589071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.589279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.589578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.589926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.590258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.590519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.590776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.591564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.591831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.597804] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [78.617290] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445]

<7> [78.618686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.648106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.648395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.648609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.648810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.649058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.649167] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.649245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.649426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.649502] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.649604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.649786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.649850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.650181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.650469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.650741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.651104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.651432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.652164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.652456] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.681466] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.681769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [78.682100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [78.682322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [78.682242] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.682540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.682662] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.682800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.683074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.683058] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.683336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.683595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.683914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.684222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.684531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.684834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.685233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.686353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.686658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.714771] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.715148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.715245] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.715443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.715666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.715625] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.715876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.715998] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.716124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.716362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.716562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.716806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.717225] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.717444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.717652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.717833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.718101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.718264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.718422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.718577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.718744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.719029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.719283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.719535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.719837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.720117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.720879] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.721192] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.748467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.748801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [78.749103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [78.749243] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.749315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [78.749517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.749603] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.749710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.749923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.749938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.750135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.750329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.750700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.750925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [78.751108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [78.751283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [78.751491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.751680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.751855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.752152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.752345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.752642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.752950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.753279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.753563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.753830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.754638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.754919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.781469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.781807] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [78.782118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [78.782147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.782331] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [78.782529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.782507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.782720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.782810] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.782938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.783115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.783356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.783738] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.783982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [78.784168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [78.784341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [78.784554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.784744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.784949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.785107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.785271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.785525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.785778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.786071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.786307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.786542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.787284] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.787557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.814745] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.815073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [78.815161] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.815317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [78.815513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [78.815492] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.815700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.815775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.815958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.816131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.816301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.816488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.816911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.817130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [78.817306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [78.817469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [78.817629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.817787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.817988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.818150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.818312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.818571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.818829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.819123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.819421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.819662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.820395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.820704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.831785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.864728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.865114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.865197] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.865371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.865593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.865579] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.865809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.865961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.866146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.866377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.866599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.866897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.867222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.867525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.867825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.868253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.868610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.869379] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.869686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.898085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.898379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [78.898629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [78.898852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [78.899025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.898976] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.899197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [78.899291] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.899362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [78.899552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [78.899560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.899735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.900029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.900291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.900547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.900862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.901125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.902121] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.902391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.931344] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.931618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [78.931866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [78.932088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [78.931996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.932302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.932415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.932533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [78.932736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [78.932772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.932987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [78.933629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.933965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.934262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [78.934552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.934910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [78.935208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [78.936030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.936310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.964890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.964950] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.965119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [78.965282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [78.965284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.965440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [78.965593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.965549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.965743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.965933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [78.966094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [78.966313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [78.966571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [78.966832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [78.967098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.967418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [78.967681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [78.968457] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [78.968722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [78.997992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [78.998226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [78.998414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [78.998567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [78.998719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [78.998929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [78.999097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [78.999051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [78.999260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [78.999385] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [78.999441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [78.999669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [78.999693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [78.999970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [79.000228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.000473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [79.000747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [79.001521] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.001812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.031878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.032259] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.032531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.056339] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446]

<7> [79.056992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.057111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [79.057176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [79.057237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [79.057296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.057353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.057410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.057465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.057518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.057570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.057628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.057680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.057729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.057793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.057848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.057902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.057968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.058059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.058144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.058225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.058305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.058385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.058686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.058793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.065589] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447]

<7> [79.066233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.098127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.098518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.098905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.099042] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.099199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.099506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.099593] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.099828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.100117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.100129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.100456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.100819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.101248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.101718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.102215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.102579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.102985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.103841] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.104203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.131417] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.131791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [79.131907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.132047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [79.132289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [79.132317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.132518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.132672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.132779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.133012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.133251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.133515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.133908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.134307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.134653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.135036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.135404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.136784] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.137177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.164789] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.165128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.165423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.165644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.166113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.166066] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.166350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.166481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.166573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.166904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.166873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.167222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.167557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.167926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.168264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.168580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.168955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.169869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.170191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.198341] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.198710] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [79.199059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [79.199193] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.199286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [79.199500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.199573] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.199709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.199999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.199957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.200219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.200469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.200816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.201143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.201499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.201834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.202166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.203017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.203303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.231339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.231650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [79.231987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [79.232118] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.232187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [79.232375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.232451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.232555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.232753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.232768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.232934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.233127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.233494] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.233744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [79.233903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [79.234097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [79.234282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.234439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.234628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.234871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.235036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.235275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.235513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.235772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.236020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.236327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.237061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.237315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.264749] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.265023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [79.265230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [79.265420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [79.265605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.265833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.265855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.266017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.266192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.266236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.266477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.266459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.266911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.267137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [79.267319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [79.267496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [79.267670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.267919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.268108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.268337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.268543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.268875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.269195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.269508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.270031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.270318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.271313] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.271621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.281463] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.314598] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.314909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.315133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.315323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.315511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.315778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.315961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.315928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.316162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.316244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.316372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.316510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.316834] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.317038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.317211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.317378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.317541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.317727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.317931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.318142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.318328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.318608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.318911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.319201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.319484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.319822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.320492] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.320804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.348085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.348400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [79.348642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [79.348919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [79.349106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.349054] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.349285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.349388] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.349458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.349650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.349701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.349907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.350329] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.350529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [79.350709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [79.350869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [79.351030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.351223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.351405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.351561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.351767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.352020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.352259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.352524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.352790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.353031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.354038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.354310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.381399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.381884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [79.381948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.382199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [79.382459] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [79.382433] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.382757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.382868] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.383004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.383307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.383541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.383922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.384284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.384666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.385019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.385416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.385813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.386804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.387166] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.414904] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.415237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [79.415498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [79.415782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [79.415916] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.415998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.416210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.416297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.416424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.416623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.416704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.416961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [79.417269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.417566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.417943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.418233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.418539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.419400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.419725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.447924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [79.448215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [79.448437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [79.448660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [79.448792] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.448844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.449033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.449114] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.449195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.449355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.449408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.449536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [79.449814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [79.450074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [79.450329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.450580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [79.450866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [79.451697] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.451985] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.481322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [79.481525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [79.481759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [79.481935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.481902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.482110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.482276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.482238] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.482475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.482525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.482783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [79.482949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [79.483100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [79.483245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [79.483388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.483530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.483716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.483857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.484057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.484313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.484567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.484858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.485182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.485450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.486279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.486586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.487410] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [79.487684] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [79.514631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [79.514858] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [79.515054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.515243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.515426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.515715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.515822] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.515925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.516154] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.516202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.516438] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.516463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.516748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.517000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.517266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.517967] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.518239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.548639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.548925] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448]

<7> [79.549025] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.549349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.549818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [79.550026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [79.550208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.550386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.550567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.550856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.551080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.551355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.551647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.551916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.552180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.552497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.553287] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.553569] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.581260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [79.581444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [79.581657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.581827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.581772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.581991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.582098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.582167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.582341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.582363] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.582592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.582828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.583067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.583314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.583590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.584274] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.584515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.614852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [79.615026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [79.615182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.615332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.615480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.615669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.615692] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.615841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.616012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.616096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.616296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.616348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.616606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.616864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.617122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.617878] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.618153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.647874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [79.648089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.648261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.648413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.648611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.648763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.648717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.648969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.649032] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.649231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.649339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.649481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.649761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.650016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.650303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.651054] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.651309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.681285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [79.681505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [79.681776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.681962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.681894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.682131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.682243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.682332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.682528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.682586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.682848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.683098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.683333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.683569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.683846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.684437] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.684751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.714611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [79.714833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [79.715032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.715259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.715484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.715779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.715931] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.716008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.716302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.716311] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.716604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.716681] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.716902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.717208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.717512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.718357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.718710] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.747927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [79.748123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [79.748304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.748476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.748718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.748894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.748837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.749130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.749192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.749544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [79.749496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.749716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [79.749882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.750062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.750211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.750358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.750532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.750787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.751024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.751251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.751547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.751779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.752415] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.752705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.781252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [79.781444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [79.781675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.781802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.781876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.782059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.782146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.782235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.782427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.782449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.782841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [79.783005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [79.783162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.783344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.783540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.783707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.783869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.784106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.784339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.784590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.784841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.785097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.785820] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.786068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.814971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [79.815233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [79.815473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.815843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.816090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.815987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.816330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.816480] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.816744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.817010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.817281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [79.817545] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [79.817779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.817999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.818204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.818406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.818679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.819141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [79.819350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [79.819633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.819831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.820027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [79.820223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [79.820433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [79.820825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [79.821221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [79.821568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.821896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [79.822208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [79.823017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.823319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.847914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [79.848193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.848424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.848725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.848846] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.848939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.849202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.849242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.849511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.849641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.849980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [79.850200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.850407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.850727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.850933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.851134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.851342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.851854] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [79.852087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [79.852300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.852493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [79.852674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [79.852849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [79.853034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.853309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.853615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.853869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.854114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.854363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.855089] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.855326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.881367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [79.881771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [79.881881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.882052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.882312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.882327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.882613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.882767] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.882893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.883135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.883351] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.883614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.883832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.885340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.885770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.931197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.931414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.931664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.931779] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.931846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.932031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.932112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.932230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.932397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.932439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.932753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.933018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [79.933310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.933586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [79.933821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [79.934489] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.934745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.965589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.965972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.966135] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449]

<7> [79.966281] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.966897] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [79.967113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [79.967309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.967539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [79.967732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [79.968023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [79.968283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [79.968632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [79.968928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [79.969200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.969547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [79.969811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [79.970579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [79.970860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [79.997845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [79.998102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [79.998318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [79.998577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [79.998716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [79.998778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [79.999005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [79.999062] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [79.999242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [79.999348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [79.999528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [79.999790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.000062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.000335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.000682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.001543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.001852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.031518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [80.031558] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.031764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [80.031986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.031968] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.032197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.032318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.032508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.032719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.032956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.033281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.033633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.034006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.034372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.034726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.035555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.035879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.064569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [80.064778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [80.064964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.065202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.065456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.065486] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.065664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.065898] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.065945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.066258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.066263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.066667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.067030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.067346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.067684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.068523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.068819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.097909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [80.098121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [80.098313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.098601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.098792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.098756] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.098973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.099125] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.099163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.099448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.099461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.099715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.099978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.100273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.100548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.101157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.101446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.131175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [80.131404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [80.131525] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.131591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.131806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.131879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.131994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.132205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.132186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.132421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.132696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.132970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.133235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.133576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.133838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.134503] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.134799] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.164553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [80.164737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [80.164905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.165115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.165319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.165569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.165712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.165778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.166068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.166096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.166355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.166459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.166750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.167065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.167322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.168076] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.168408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.180446] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off

<7> [80.180730] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [80.197790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [80.197956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [80.198108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.198261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.198464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.198626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.198588] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.198807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.198923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.199069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.199224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.199332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.199638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.199946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.200241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.201006] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.201282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.231484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [80.231478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.231687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [80.231876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.231856] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.232058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.232227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.232173] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.232430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.232625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [80.232947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [80.233197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [80.233469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.233770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [80.234037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [80.234763] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.235038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.264535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [80.264742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [80.264933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.265161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.265393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.265431] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.265595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.265799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [80.265812] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.266076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.266122] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.266354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.266670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.266924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.267162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.267874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.268130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.298375] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.298823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.299179] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.323466] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450]

<7> [80.324006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.324108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [80.324170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [80.324228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [80.324285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.324359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.324418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.324477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.324532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.324583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [80.324642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [80.324700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [80.324757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.324814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.324868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.324921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.324991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.325116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.325185] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [80.325239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [80.325291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [80.325357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.325410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.325465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.325523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.325583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.325642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [80.325699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [80.325752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [80.325802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.325854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.325906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.325953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.326004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.326085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.326166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.326244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.326328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.326413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.326854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.326942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.330867] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [80.349453] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451]

<7> [80.350532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.381367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.381422] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.381762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.381916] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.382072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.382409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.382395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.382705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.383048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.383352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.383677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.383998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.384567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.384908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.385243] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.385589] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.385904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.386194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.386502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.386783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.387063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.387463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.387812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.388238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.388627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.389003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.389858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.390190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.414594] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.414950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [80.415328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [80.415461] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.415592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [80.415848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.415913] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.416094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.416360] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.416409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.416684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.416958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.417596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.417895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [80.418190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [80.418467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [80.418713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.418938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.419164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.419427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.419661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.419981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.420306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.420666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.420974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.421294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.422099] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.422383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.447806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.448137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.448431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.448558] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.448653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.448859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.448942] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.449074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.449324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.449337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.449562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.449839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.450431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.450713] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.450997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.451220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.451526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.451775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.452006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.452246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.452547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.452885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.453204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.453591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.453904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.454188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.455092] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.455385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.481370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.481465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.481814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [80.481784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.482072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [80.482137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.482418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [80.482711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.482940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.483143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.483432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.483686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.483998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.484312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.484660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.484951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.485240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.486101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.486438] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.514525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.514922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [80.515182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [80.515505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [80.515734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.515643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.515956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.516079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.516176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.516458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.516482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.516700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.517036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.517447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.517743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.518032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.518429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.519417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.519745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.547780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.548050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [80.548303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [80.548412] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.548497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [80.548681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.548745] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.548859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.549035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.549029] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.549218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.549459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.549707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.549952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.550199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.550548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.550860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.551816] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.552066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.564762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.597715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.597984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.598265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.598373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.598464] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.598654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.598731] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.598841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.599020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.599027] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.599242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.599431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.599694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.599951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.600205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.600506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.600811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.601527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.601794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.631121] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.631462] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [80.631511] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.631663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [80.631847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [80.631864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.632022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.632198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.632164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.632430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.632593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.632778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.633066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.633328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.633567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.633800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.634032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.634804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.635063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.664438] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.664704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [80.664905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [80.665091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [80.665313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.665490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.665453] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.665664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.665831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.665810] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.666057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.666107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.666355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.666608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.666859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.667090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.667409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.668077] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.668376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.697997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.698327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [80.698418] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.698553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [80.698764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [80.698826] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.698970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.699159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.699240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.699413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.699619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.699839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [80.700120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [80.700437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [80.700708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.700982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [80.701325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [80.702196] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.702478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.731083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.731395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [80.731473] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.731646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [80.731847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [80.731858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.732026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.732255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.732218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.732430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.732608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.732805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [80.733076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [80.733355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [80.733601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.733843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [80.734086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [80.734768] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.735008] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.765266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.765633] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.765948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452]

<7> [80.765918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.767577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.767833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [80.768022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [80.768229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [80.768394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.768557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.768715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.768900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.769086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.769297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.769462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.769620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.769774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.769962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.770139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.770358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.770541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.770783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.771021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.771301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.771604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.771845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.772722] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.772972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.783907] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453]

<7> [80.785769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.814519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.814890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.815205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.815447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.815675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.815897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.816133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.816437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.816529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.816695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.816910] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.817199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.817277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.817475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.817689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.817876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.818058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.818317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.818499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.818676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.818864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.819171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.819467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.819758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.820047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.820372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.821128] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.821465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.847907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.848290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [80.848373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.848573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [80.848792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [80.848756] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.849000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.849086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.849316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.849539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.849808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.850053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.850696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.850962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [80.851238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [80.851440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [80.851642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.851839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.852038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.852315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.852525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.852851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.853165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.853515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.853870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.854204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.855078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.855432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.881191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.881524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.881772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.881995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.882244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.882441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.882376] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.882634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.882735] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.882860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.883045] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.883064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.883471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.883692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [80.883895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [80.884058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [80.884249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.884401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [80.884551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [80.884721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [80.884905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.885179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.885436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.885691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.885943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.886228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.886874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.887142] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.914697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.915040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [80.915440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [80.915581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.915695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [80.915934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.915996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.916169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.916406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.916384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.916609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.916844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.917404] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.917648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [80.917841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [80.918028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [80.918299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.918483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.918666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [80.918843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [80.919034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.919350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.919681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.919965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.920269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.920534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.921315] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.921588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.948263] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.948647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.948652] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.948970] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [80.948976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.949316] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [80.949528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [80.949721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.949945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.950166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.950356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.950587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.951034] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.951276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [80.951447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [80.951607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [80.951765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.951923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [80.952081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [80.952295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [80.952459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [80.952710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [80.952962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [80.953297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.953551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [80.953799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [80.954585] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.954857] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.981147] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [80.981521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [80.981759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [80.981975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [80.982240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [80.982277] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [80.982450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [80.982657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [80.982687] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [80.982899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [80.983013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [80.983163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [80.983451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [80.983733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [80.984011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.984356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [80.984609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [80.985573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [80.985842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [80.998159] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.031024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.031342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [81.031546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [81.031740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [81.031923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.032242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.032344] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.032428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.032602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.032676] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.032801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.032961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.033086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.033356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.033621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.033877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.034141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.034775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.035036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.064390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.064676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [81.064906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [81.065153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [81.065190] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.065360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.065564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.065572] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.065755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.065936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.065894] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.066177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.066455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.066730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.067047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.067395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.067682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.068501] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.068795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.097693] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.097983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [81.098277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [81.098457] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [81.098416] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.098628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.098729] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.098796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.098974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.099006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.099250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.099461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.099730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.099994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.100368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.100671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.100938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.101780] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.102083] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.131275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.131565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [81.131813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [81.132007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [81.132292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.132420] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.132495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.132704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.132803] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.132888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.133120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [81.133159] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.133419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.133712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.134032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.134373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.134654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.135523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.135803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.164367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [81.164700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [81.164955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [81.165270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [81.165396] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.165506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.165727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.165805] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.165947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.166236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.166207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.166474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [81.166805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [81.167184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [81.167503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.167818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [81.168219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [81.169134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.169464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.197814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [81.198123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [81.198203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.198368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [81.198565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.198559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.198743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.198865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.198923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.199148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.199326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [81.199498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [81.199666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [81.199836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [81.199995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.200201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.200353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.200506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.200680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.200938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.201224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.201528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.201774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.202037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.202752] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.203035] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.203720] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [81.203948] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [81.231047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.231281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.231470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.231645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.231816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.232076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.232202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.232308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.232543] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.232584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.232831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.232845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.233140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.233460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.233761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.234497] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.234801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.265214] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454]

<7> [81.265117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.265537] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.265916] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.282770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [81.283135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [81.283413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.283675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.283933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.284460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.284750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.285124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.285411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.285697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.285973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.286291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.287142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.287439] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.314467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.314733] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.314952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.315256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.315493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.315770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.316037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.316073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.316471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.316487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.316822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.316873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.317227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.317620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.318011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.319375] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.319832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.348031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [81.348312] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [81.348546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.348762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.349010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.349043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.349239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.349384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.349546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.349692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.350043] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [81.350285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [81.350513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.350764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.351004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.351227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.351457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.351809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.352190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.352566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.352907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.353288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.354365] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.354737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.381102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [81.381379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [81.381612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.381829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.382108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.382228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.382335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.382641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.382637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.383020] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.383222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [81.383451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [81.383663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.383865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.384136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.384396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.384624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.384986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.385347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.385655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.385973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.386278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.387190] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.387529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.414397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [81.414671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [81.414906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.415234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.415353] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.415475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.415747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.415771] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.416054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.416177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.416519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [81.416737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [81.416957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.417166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.417373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.417602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.417811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.418309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [81.418536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [81.418729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.418921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.419184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.419397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.419638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.419983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.420273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.420556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.420900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.421254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.421990] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.422270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.447698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.448025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.448155] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.448287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.448527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.448567] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.448762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.448920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.449108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.449424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.450027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.450273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.450517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.450752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.451037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.451287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.451531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.452082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.452305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.452513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.452715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.452984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.453202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.453412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.453718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.454027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.454303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.454569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.454816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.455556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.455812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.481135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [81.481450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [81.481707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.481981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.482045] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.482205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.482385] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.482433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.482668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.482684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.482992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.483318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.483635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.484025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.484357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.485248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.485555] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.514337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [81.514585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [81.514793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.515061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.515087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.515289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.515432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.515546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.515743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.515790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.516161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.516508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.516842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.517245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.517668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.518742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.519136] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.547871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [81.548174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [81.548290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.548376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.548591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.548649] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.548776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.548992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.548990] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.549188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [81.549461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [81.549729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [81.550070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.550345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [81.550601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [81.551361] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.551635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.580953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [81.581144] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [81.581314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.581477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.581639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.581832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.582107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.582218] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.582426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.582574] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.582693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.582877] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.582963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.583210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.583505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.584254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.584517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.614343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [81.614549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [81.614733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.614956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.615139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.615082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.615313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.615483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.615435] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.615648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.615738] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.615812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.616036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.616661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.616922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.664432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.664754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.665086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.665233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.665331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.665563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.665655] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.665802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.666059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.666183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.666498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.666801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.667184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.667500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.667883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.668715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.669072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.698020] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.698430] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.698677] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455]

<7> [81.698755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.715093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [81.715403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [81.715668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.715979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.716211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.716436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.716939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.717237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.717523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.717800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.718282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.718532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.719438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.719744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.747741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.748135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.748089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.748378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.748604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.748545] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.748877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.748971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.749137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.749425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.749812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.750231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.750631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.751026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.751327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.752243] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.752604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.781305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.781613] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.781924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.782067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.782149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.782368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.782449] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.782604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.782777] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.782857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.783172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.783476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.783796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.784164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.784481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.785403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.785718] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.814254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [81.814519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [81.814736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.815004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.815148] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.815207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [81.815442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [81.815504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.815688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.815806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.816025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.816324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.816606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.816888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.817192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.817971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.818260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.847663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [81.847951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [81.848043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.848130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.848294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.848377] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.848462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.848627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.848660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.848835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.849083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.849320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.849552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.849780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.850079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.850692] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.850979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.880901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.881094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.881264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.881422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.881582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.881742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.881981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.882100] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.882227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.882413] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.882457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.882681] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.882702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.883005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.883268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.884287] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.884586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.914285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [81.914512] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [81.914704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.914950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.915080] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.915135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.915335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.915394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.915547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.915662] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.915923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [81.916106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [81.916282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.916462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [81.916628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [81.916813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [81.916981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.917220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.917459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.917694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.918014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.918263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.919003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.919257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.947609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.947863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.948061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.947996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.948299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.948380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.948493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.948682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.948703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.948952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.949327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [81.949507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [81.949680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.949961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [81.950153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [81.950339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [81.950536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [81.950849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [81.951139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [81.951450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.951729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [81.952052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [81.952841] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.953127] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [81.981194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.981469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.981703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.981993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.982138] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [81.982201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.982441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.982498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [81.982679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.982831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [81.983124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.983306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.983482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.983686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.983894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.984073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.984246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.984600] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [81.984782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [81.984945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [81.985105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [81.985264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [81.985422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [81.985583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [81.985853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [81.986108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [81.986384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.986627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [81.986908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [81.988061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [81.988319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.014220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [82.014483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [82.014703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.014979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.015163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.015116] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.015391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.015452] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.015610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.015733] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.016029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [82.016201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [82.016358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.016513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.016664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.016858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.017020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.017370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [82.017531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [82.017688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.017883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.018038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.018200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.018371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [82.018643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.018947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.019213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.019474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.019807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.020571] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.020868] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.047901] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.048262] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.048507] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456]

<7> [82.048548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.066428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.066948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [82.067200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [82.067398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [82.067590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.067801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.067985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [82.068200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [82.068393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.068599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.068823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [82.068999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [82.069163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.069314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.069465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.069611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.069803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.070208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.070386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [82.070518] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [82.070648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [82.070867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.071014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.071137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [82.071258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [82.071373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.071486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.071599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [82.071706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [82.071856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.071963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.072068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.072171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.072279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.072449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.072615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.072781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.072958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.073119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.073722] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.073906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.080596] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [82.098990] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457]

<7> [82.114780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.115153] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.115469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.118482] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.119481] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.119744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.147571] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.147958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [82.148030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.148246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [82.148489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [82.148440] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.148753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.148822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.148988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.149223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.149507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.149844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.150183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.150513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.150866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.151199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.151577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.152468] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.152827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.180907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.181187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [82.181393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [82.181580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [82.181810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.181988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.181932] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.182154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.182249] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.182342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.182512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.182545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.182877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.183139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.183398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.183653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.183997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.184715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.184965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.214162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.214441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [82.214728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [82.214930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [82.214859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.215121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.215229] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.215327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.215516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.215533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.215709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.215909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.216186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.216458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.216764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.217017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.217284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.218057] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.218301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.247696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.247834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.247935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [82.248106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [82.248166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.248267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [82.248423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.248452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.248578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.248763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.248917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.249088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.249325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.249592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.249854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.250086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.250336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.250995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.251256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.280815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.281047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [82.281260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [82.281445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [82.281601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.281861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.282027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.281976] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.282183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.282309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.282376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.282593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.282650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.282945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.283195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.283473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.283733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.284426] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.284684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.314142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.314379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [82.314562] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [82.314777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [82.314944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.314920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.315130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.315289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.315252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.315445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.315535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.315642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.315957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.316194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.316474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.316743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.316975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.317866] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.318150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.331135] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.364161] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.364432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [82.364622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [82.364885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [82.364894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.365086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.365275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.365284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.365464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.365616] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.365747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.365967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.366292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.366612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.366988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.367337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.367639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.368672] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.369033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.397602] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.398006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [82.398109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.398311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [82.398563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [82.398561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.398899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.399007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.399121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.399339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.399559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.399881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.400283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.400676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.401013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.401343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.401751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.404132] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.404463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.430881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.431180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [82.431418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [82.431611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [82.431856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.432040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.432004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.432218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.432346] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.432399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.432599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.432657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.432908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.433189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.433461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.433785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.434064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.434972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.435259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.464359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.464676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [82.464780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.464934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [82.465137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [82.465112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.465319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.465393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.465499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.465705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.465883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.466115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.466513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.466760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [82.466931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [82.467092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [82.467265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.467448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.467608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.467826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.467994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [82.468252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [82.468508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [82.468788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.469047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [82.469272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [82.469959] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.470230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.497521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.497876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [82.497873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.498086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [82.498158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.498281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [82.498417] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.498465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.498676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.498857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.499076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.499299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.499714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.499950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [82.500145] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [82.500338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [82.500524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.500756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.500985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.501192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.501401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [82.501715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [82.502050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [82.502342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.502646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [82.502992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [82.503817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.504103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.533003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.533461] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.533854] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458]

<7> [82.533870] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.555485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.555842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [82.556031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [82.556206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [82.556364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.556512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.556690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.556826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.556977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.557123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.557246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.557381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.557506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.557640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.557752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.557859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.557990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.558242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.558368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [82.558467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [82.558560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [82.558790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.558883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.558975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.559064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.559151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.559235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.559319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.559400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.559478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.559555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.559664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.559742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.559856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.559984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.560111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.560235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.560351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.560467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.560958] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.561080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.564966] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459]

<7> [82.577474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.597453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.597734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.597819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.598027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.598064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.598225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.598350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.598415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.598681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.598875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.599116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.599357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.599852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.600102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.600303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.600502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.600801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.601009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.601247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.601464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.601725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.602058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.602379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.602723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.603095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.603405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.604252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.604592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.630938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.631270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [82.631583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [82.631804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [82.632012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.632208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.632407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.632696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.632702] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.632944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.633031] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.633264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.633326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.633576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.633874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.634216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.634513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.635378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.635703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.664251] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.664693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.664723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.665015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.665066] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.665274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.665398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.665522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.665829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.666056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.666316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.666614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.666961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.667285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.667721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.668041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.668349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.669249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.669574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.697696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.697706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.698017] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [82.698068] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.698238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [82.698371] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.698442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [82.698691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.698886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.699066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.699278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.699496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.699837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.700080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.700320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.700568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.700804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.701593] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.701861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.730756] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.731004] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [82.731230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [82.731400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [82.731606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.731779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.731752] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.731946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.732107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.732086] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.732288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.732368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.732569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.732822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.733073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.733319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.733627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.734349] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.734636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.764112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.764377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [82.764691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [82.764885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [82.764841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.765127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.765251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.765340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.765557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.765642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.765772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.765983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.766276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.766582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.766930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.767222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.767499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.768564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.768861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.781126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.814073] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.814387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.814710] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.814845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.814938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.815184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.815241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.815389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.815620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.815597] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.815814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.816034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.816340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.816670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.816962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.817254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.817608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.818341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.818694] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.847526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.847869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [82.848113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [82.848337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [82.848596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.848806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.848749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.849011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.849133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.849236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.849459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.849461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.849817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.850120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.850415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.850739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.851050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.851937] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.852245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.880822] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.881208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [82.881559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [82.881569] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.881827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [82.882028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.882117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.882384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [82.882457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.882716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [82.882997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [82.883292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.883740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.884155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.884560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.884965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.885334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.886526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.886926] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.914332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.914719] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [82.914812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.914958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [82.915167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [82.915182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.915368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.915527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.915651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.915851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [82.916033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [82.916232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [82.916510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [82.916777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [82.917032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.917264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [82.917506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [82.918234] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.918524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.947387] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [82.947662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [82.947880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [82.948063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [82.948277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.948493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [82.948707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [82.948648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.948878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [82.949015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.949085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [82.949343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.949379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [82.949728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [82.950013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.950293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [82.950603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [82.951443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.951789] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.980850] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026

<7> [82.981075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [82.981272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025

<7> [82.981504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.981708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.981657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [82.981912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.982093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.982038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [82.982264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [82.982344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [82.982434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.982657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.982827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.982993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.983166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.983370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.983594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.983782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.984198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026

<7> [82.984371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [82.984585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025

<7> [82.984751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.984915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.985072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.985225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.985381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [82.985580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.985733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.985888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [82.986036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [82.986185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [82.986335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [82.986510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [82.986706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [82.986997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [82.987266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [82.987525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.987774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [82.988010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [82.988652] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [82.988897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [82.989696] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [82.989924] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [83.030728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.031010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.031270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.031626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.031722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.031929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.032163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.032132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.032421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.032518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.032969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.033209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.033426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.033706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.033926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.034175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.034394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.034915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.035162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.035368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.035742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.035958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.036192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.036481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.036809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.037112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.037400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.037784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.038071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.038803] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.039090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.064139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [83.064421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [83.064742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.064856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.064968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.065194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.065255] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.065453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.065656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.065708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.066178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [83.066398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [83.066689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.066897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.067112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.067314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.067570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.068015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [83.068220] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [83.068416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.068687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.068883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.069069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.069254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.069579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.069929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.070198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.070481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.070792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.071655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.071957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.097497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.097827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.098103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.098358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.098764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.098733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.099015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.099188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.099293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.099635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.099737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.100078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.100398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.100769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.101127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.102176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.102528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.131387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [83.131699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [83.131829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.131906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.132094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.132157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.132271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.132462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.132502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.132716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.132972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.133241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.133519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.133772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.134015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.134771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.135055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.164053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [83.164308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [83.164611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.164724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.164819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.165012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.165071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.165215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.165351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.165434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.165705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.165969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.166224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.166490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.166789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.167625] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.167886] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.197379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [83.197599] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [83.197756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.197921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.198095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.198265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.198491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.198612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.198754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.198944] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.199002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.199219] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.199238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.199502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.199775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.200413] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.200656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.247348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.247572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.247730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.247882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.248034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.248182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.248351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.248636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.248761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.248868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.249074] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.249098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.249339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.249368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.249645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.250229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.250590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.280714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [83.280912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [83.281104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.281288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.281535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.281732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.281662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.281937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.282044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.282215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.282347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.282509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.282825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.283079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.283327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.284061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.284323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.313960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [83.314136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [83.314294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.314543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.314699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.314679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.314852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.314990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.315024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.315277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.315286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.315556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.315855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.316100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.316342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.317164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.317427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.347574] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [83.347771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [83.347946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.348144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.348301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.348586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.348631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.348801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [83.348945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.349044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [83.349226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.349298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [83.349609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.349856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [83.350088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [83.350730] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.350971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.380661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [83.380887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [83.381082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.381269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.381521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.381636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.381730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.381952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.382017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.382248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.382378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.382571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.382857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.383118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.383427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.384229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.384522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.414021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [83.414203] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [83.414425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.414598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.414554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.414767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.414931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.414911] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.415086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.415233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.415202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.415416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.415565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.416101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.416351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.464034] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [83.464277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [83.464558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.464677] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.464749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.464929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.465012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.465141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.465293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.465382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.465652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.465910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.466148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.466459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.466696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.467347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.467596] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.497499] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460]

<7> [83.498392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [83.498479] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.498624] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [83.498802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.498812] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.498982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.499163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.499114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.499366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.499570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.499968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [83.500146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [83.500339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.500541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.500713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.500878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.501055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.501342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.501610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.501876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.502182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.502495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.503233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.503526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.530702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [83.530959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [83.531184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.531463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.531577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.531678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.531924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.531960] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.532148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.532286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.532588] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [83.532786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [83.532972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.533190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.533405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.533584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.533771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.534045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.534320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.534604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.534860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.535105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.535942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.536208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.564236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [83.564571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [83.564717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.564807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.565024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.565098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.565234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.565479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.565557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.565799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.566228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [83.566497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [83.566693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.566906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.567084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.567258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.567560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.567965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [83.568139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [83.568332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.568532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.568709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.568872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.569050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.569362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.569659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.569952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.570217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.570531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.571371] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.571679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.597339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [83.597598] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [83.597816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.598028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.598234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.598572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.598719] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.598804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.599101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.599326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [83.599473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.599530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [83.599724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.599916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.600104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.600312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.600508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.600922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [83.601110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [83.601324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.601506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.601679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.601877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.602052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.602348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.602607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.602860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.603107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.603409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.604162] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.604413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.630703] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [83.630977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [83.631198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.631466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.631594] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.631666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.631898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.631945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.632113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.632228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.632454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.632717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.632975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.633292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.633556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.634178] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.634472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.663944] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [83.664137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [83.664364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.664545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.664497] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.664726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.664852] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.664935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.665148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.665148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.665446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.665698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.665945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.666209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.666480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.667170] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.667459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.697371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [83.697575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [83.697756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.697973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.698173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.698422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.698539] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.698848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.698919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.699128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.699230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.699438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.699701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.700019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.700311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.700985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.701264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.730648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [83.730857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [83.731038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.731330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.731449] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.731526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.731745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.731829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.731978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.732153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.732322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.732637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.732897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.733140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.733413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.734168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.734482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.764208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [83.764501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [83.764695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.764609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.764879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.765060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.764990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.765262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.765372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.765465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [83.765757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [83.766037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [83.766378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.766654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [83.766911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [83.767628] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.767882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.797255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [83.797442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [83.797610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.797795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.797955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [83.798113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [83.798336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [83.798398] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.798592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [83.798735] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.798846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [83.799018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.799088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.799357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [83.799627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [83.800429] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.800683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.831348] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.831741] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.832038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.832227] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461]

<7> [83.833269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.833499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [83.833667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [83.833826] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [83.833991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.834188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.834432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.834592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.834747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.834897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [83.835042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [83.835181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [83.835374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.835515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.835653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.835790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.835964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.836235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.836544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.836815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.837047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.837285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.837954] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.838233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.846961] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [83.866278] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462]

<7> [83.867736] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.897281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.897602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.897868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.898091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.898391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.898520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.898620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.898843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.898932] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.899114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.899321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.899434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.899823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.900154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.900539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.900907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.901243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.902114] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.902517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.930599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.930886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [83.931135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [83.931384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [83.931557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.931518] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.931755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [83.931831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.931918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [83.932081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [83.932099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.932313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.932580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.932840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.933082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.933349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [83.933579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [83.934564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.934829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.963887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.964133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [83.964429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [83.964606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [83.964555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.964776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.964889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.964975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [83.965151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [83.965194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.965369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [83.965541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [83.965782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [83.966021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [83.966288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.966600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [83.966846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [83.967564] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [83.967807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [83.997414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [83.997661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [83.997838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [83.998007] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [83.998201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [83.998324] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [83.998388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [83.998567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [83.998639] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [83.998727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [83.998896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [83.998908] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [83.999153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [83.999452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [83.999755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.000004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.000311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.001067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.001411] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.030547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.030820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [84.031026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [84.031311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [84.031401] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.031492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.031665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.031758] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.031871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.032050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.032057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.032260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.032628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.032823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [84.032977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [84.033134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [84.033364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.033513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.033661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.033835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.034028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.034322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.034573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.034820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.035065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.035344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.036099] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.036386] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.063959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.064329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [84.064330] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.064586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [84.064663] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.064776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [84.064960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.064945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.065204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.065379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.065570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.065754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.066109] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.066748] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [84.066920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [84.067079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [84.067267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.067421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.067571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.067747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.067931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.068202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.068464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.068773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.069049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.069319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.070019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.070315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.080721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.113861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.114188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.114296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.114462] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.114671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.114650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.114870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.114950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.115098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.115347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.115525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.115730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.116176] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.116389] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.116560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.116728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.116892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.117089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.117324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.117493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.117670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.117932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.118200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.118510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.118799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.119046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.119778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.120042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.147284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.147573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [84.147777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [84.147964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [84.148176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.148236] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.148348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.148514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.148548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.148708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.148821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.148892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.149357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.149567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [84.149773] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [84.149951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [84.150134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.150318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.150474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.150646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.150839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.151080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.151353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.151590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.151870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.152111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.153179] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.153443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.180500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.180788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [84.181042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [84.181287] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [84.181368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.181463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.181631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.181707] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.181796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.181978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.181972] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.182189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.182457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.182720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.182975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.183291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.183552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.184309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.184579] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.214126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.214274] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.214402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [84.214604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [84.214630] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.214791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [84.214974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.214934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.215184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.215355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.215556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.215761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [84.216072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [84.216351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [84.216637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.216886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [84.217144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [84.217911] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.218186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.247173] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.247422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [84.247607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [84.247783] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [84.247958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.248175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.248354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.248331] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.248554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.248686] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.248745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [84.248987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.249014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [84.249296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [84.249589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.249833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [84.250064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [84.250771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.251013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.300215] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.300367] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.300461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.300952] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463]

<7> [84.301577] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.301678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [84.301743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [84.301802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [84.301858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.301915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.301970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.302024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.302120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.302177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.302234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.302288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.302341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.302395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.302445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.302494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.302570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.302654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.302735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.302816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.302896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.302976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.303282] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.303378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.315549] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464]

<7> [84.316474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.347267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.347668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.347977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.348395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.348508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.348700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.348980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.349002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.349333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.349503] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.349605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.349942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.350388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.350785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.351274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.351662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.352049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.353041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.353467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.380660] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.381050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [84.381452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [84.381598] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.381700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [84.381936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.382010] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.382200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.382455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.382424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.382670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.382913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.383280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.383607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.383933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.384313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.384667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.385820] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.386166] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.413877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.414298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.414362] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.414577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.414813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.414770] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.415036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.415184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.415384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.415609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.415872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.416184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.416517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.416843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.417194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.417484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.417770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.418599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.418903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.447468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.447796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [84.448104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [84.448227] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.448317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [84.448521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.448587] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.448719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.448912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.448889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.449192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.449404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.449667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.449932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.450240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.450510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.450776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.451599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.451903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.480447] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.480738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [84.480992] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [84.481262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [84.481339] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.481437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.481604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.481653] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.481770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.481927] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.481961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.482631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.482901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.483184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.483428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.483666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.483946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.484711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.484978] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.513838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.514114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [84.514189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.514318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [84.514488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [84.514523] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.514655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.514816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.514803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.514978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.515177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.515353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.515596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.515834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.516094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.516399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.516653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.517358] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.517603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.530796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.563838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.564114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.564217] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.564299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.564476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.564551] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.564646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.564812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.564833] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.564978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.565238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.565438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.565800] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.566041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.566202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.566358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.566546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.566720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.566883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.567065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.567223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.567462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.567699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.567932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.568189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.568418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.569017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.569271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.597305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.597597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [84.597804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [84.597988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [84.598228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.598398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.598367] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.598565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.598684] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.598738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.598922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.598955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.599321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.599531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [84.599699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [84.599862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [84.600039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.600190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.600343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.600491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.600645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.600888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.601179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.601434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.601732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.601973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.602955] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.603266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.630498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.630813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.631083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.631173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.631279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.631462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.631514] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.631642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.631816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.631797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.632051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.632274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.632718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.632928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [84.633179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [84.633346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [84.633507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.633701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.633868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.634061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.634219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.634464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.634701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.634959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.635251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.635548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.636255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.636506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.664050] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.664136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.664335] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [84.664451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.664567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [84.664746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [84.664721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.664915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.665135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.665321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.665504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.665701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.666159] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.666370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [84.666538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [84.666701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [84.666863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.667063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.667229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.667389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.667555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [84.667815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [84.668110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [84.668366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.668668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [84.668911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [84.669655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.669926] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.697125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [84.697418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [84.697656] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [84.697847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [84.698105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.698179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.698280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.698447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.698493] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.698621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.698759] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.698803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [84.699087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [84.699354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [84.699616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.699871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [84.700158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [84.700939] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.701251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.730504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [84.730696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [84.730861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [84.731072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.731245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.731198] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.731422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.731527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.731587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.731751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [84.731808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.731905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [84.732101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [84.732259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [84.732430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.732575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.732719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.732863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.733081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.733343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.733597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.733905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.734170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.734401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.735115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.735374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.736051] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [84.736258] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [84.763880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.764240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.764379] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.764494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.764728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.764791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.764982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.765197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.765257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.765518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.765850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.766227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.766548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.766860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.767216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.768053] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.768356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.798763] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465]

<7> [84.798620] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.799030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.799333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.799579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [84.799798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [84.800050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.800260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.800467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.800713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.800999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.801304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.801597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.801886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.802249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.802526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.803264] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.803546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.830469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.830725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.830980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.831170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.831110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.831353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.831442] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.831566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.831726] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.831788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.832082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.832331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.832572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.832807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.833136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.833910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.834215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.864031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [84.864067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.864217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [84.864383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.864382] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.864543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.864650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.864703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [84.864858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [84.865081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.865379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.865634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.865881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.866153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.866384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.867017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.867260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.897073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [84.897243] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [84.897402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.897586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [84.897741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [84.897891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [84.898170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.898474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.898503] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.898734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.898785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.898995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.899232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.899460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.899739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.900458] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.900716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.930433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [84.930657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [84.930845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.931082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.931152] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.931263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.931463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.931465] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.931675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.931729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.931975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.932222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.932461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.932698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.932949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [84.933612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.933880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.963734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [84.963973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [84.964145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.964102] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.964344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [84.964436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.964531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [84.964732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [84.964719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.964963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [84.965207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [84.965445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [84.965677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.965918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [84.966193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [84.966794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [84.967074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [84.997118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [84.997314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [84.997477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [84.997670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [84.997855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [84.998115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [84.998151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [84.998307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [84.998482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [84.998561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [84.998768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [84.998811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [84.999106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.999350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [84.999587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.000272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.000526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.030349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [85.030538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [85.030696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.030930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.031105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.031072] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.031268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.031405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.031450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.031690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.031702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.031970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.032218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.032458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.032745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.033486] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.033746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.063953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [85.064017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.064150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [85.064319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.064353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.064480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.064639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.064638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.064794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.065004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.065360] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [85.065519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [85.065672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.065820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.066065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.066224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.066379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [85.066624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [85.066896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [85.067143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.067405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [85.067663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [85.068308] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.068578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.097155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [85.097401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [85.097602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.097790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.098031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.098212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.098173] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.098453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.098504] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.098786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.098844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [85.099077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [85.099246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.099410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.099574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.099733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.099923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.100169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.100406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.100640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.100914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.101186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.101926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.102193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.130402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [85.130648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [85.130885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.131071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.131025] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.131245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.131339] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.131441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.131605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.131608] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.131764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.131965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.132148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.132473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [85.132638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [85.132798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.133024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.133183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.133330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.133477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.133618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.133760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.133939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.134205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [85.134364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [85.134520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.134701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.134870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.135013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.135153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.135291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.135430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.135569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.136196] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.136459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.180420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.180668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.180919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.181115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.181051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.181303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.181388] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.181514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.181672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.181718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.182165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.182376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.182547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.182715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.182913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.183092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.183279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.183631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.183795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.183999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.184148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.184297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.184440] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.184591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.184831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.185132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.185436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.185683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.186014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.186709] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.187010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.213996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.214338] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.214604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.215303] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466]

<7> [85.216187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [85.216421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [85.216629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.216823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.217070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.217257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.217511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.217788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.218172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.218437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.218694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.219038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.219752] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.220054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.247127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.247379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.247595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.247795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.248056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.248201] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.248254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.248477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.248535] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.248745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.248817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.249034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.249277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.249540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.249775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.250612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.250893] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.280517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [85.280714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [85.280944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.281083] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.281157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.281339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.281415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.281507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.281696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.281698] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.282000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.282257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.282508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.282753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.283072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.283698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.283969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.313663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [85.313883] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [85.313927] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.314038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.314206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.314240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.314355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.314506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.314505] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.314890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.315195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.315452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.315703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.315980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.316225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.317014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.317278] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.347077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [85.347280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [85.347457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.347632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.347841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.348020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.347997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.348260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.348333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.348527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.348615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.348778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.349069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.349312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.349549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.350233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.350495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.380311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.380494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.380648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.380835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.381009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.380971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.381192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.381304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.381378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.381587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.381631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.381934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.382206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.382465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.382751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.383459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.383754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.413693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [85.413915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [85.414076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.414053] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.414232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.414384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.414367] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.414533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.414631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.414702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.414964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.415211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.415474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.415721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.415994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.416674] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.416961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.446990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [85.447162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [85.447318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.447476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.447634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.447822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.447854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.447998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.448129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.448234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.448371] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.448464] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.448734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.449014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.449271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.450029] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.450302] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.480474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [85.480651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [85.480850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.480856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.481019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.481130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.481221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.481377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.481385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.481557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [85.481822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [85.482111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [85.482380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.482663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [85.482956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [85.483715] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.484057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.513649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [85.513895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [85.514080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.514023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.514300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.514406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.514492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.514704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.514736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.514968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [85.515282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [85.515589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [85.515928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.516214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [85.516486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [85.517279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.517547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.552182] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.552645] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.553106] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467]

<7> [85.553113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.554858] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.555260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [85.555601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [85.555947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [85.556212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.556452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.556690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.556986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.557248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.557475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [85.557681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [85.557940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [85.558151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.558389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.558581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.558793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.559014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.559304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.559585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.559898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.560149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.560377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.561254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.561484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.563439] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [85.582015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468]

<7> [85.583158] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.613630] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.613930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.614140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.614339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.614531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.614718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.614975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.615163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.615131] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.615396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.615463] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.615773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.615844] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.616071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.616246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.616413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.616577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.616759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.616920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.617086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.617264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.617523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.617794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.618052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.618319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.618583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.619411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.619678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.647111] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.647379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [85.647573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [85.647799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [85.647974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.647919] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.648150] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.648243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.648326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.648536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.648526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.648817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.649175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.649373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [85.649531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [85.649685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [85.649883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.650078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.650260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.650416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.650583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.650874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.651152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.651424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.651692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.652027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.652893] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.653188] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.680327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.680610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.680871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.681062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.681018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.681246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.681422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.681378] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.681600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.681660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.681863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.682493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.682883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.683098] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.683272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.683445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.683610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.683820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.683989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.684154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.684323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.684585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.684876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.685188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.685437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.685756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.686522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.686822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.713860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.714189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [85.714411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [85.714617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [85.714930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.714902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.715115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.715292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.715363] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.715490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.715684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.715728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.716167] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.716376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [85.716571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [85.716761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [85.716922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.717080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.717239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.717394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.717558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.717840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.718095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.718348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.718599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.718884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.719674] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.719991] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.746986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.747320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [85.747544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [85.747873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [85.747825] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.748068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.748165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.748254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.748434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.748450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.748635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.748880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.749353] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.749582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [85.749802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [85.749990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [85.750181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.750371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.750597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.750828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.751050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.751376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.751713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.752086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.752428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.752743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.753648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.753983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.780497] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.781004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.781041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [85.781378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [85.781427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.781663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [85.781855] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.782094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.782386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.782627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.782985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.783241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.783573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.783933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.784341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.784698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.785040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.786233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.786580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.797405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.830277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.830611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.831022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.831119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.831265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.831499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.831528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.831762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.831933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.832040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.832259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.832506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.832873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.833253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.833577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.833938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.834339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.835232] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.835574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.863629] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.863941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [85.864152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [85.864340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [85.864519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.864754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [85.864788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.864934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [85.865115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [85.865088] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.865356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.865322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.865638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.865971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.866247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.866519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.866862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.867681] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.867979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.896900] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.897164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [85.897386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [85.897571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [85.897806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.897998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [85.897944] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.898191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [85.898327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.898424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [85.898674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.898678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.898973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.899248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.899515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.899870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.900172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.900937] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.901236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.930401] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.930662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [85.930843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [85.931009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [85.931175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.931361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.931529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [85.931714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [85.931850] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.931909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [85.932192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.932204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [85.932457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [85.932477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.932724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.932985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [85.933279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [85.934005] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.934306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [85.963919] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [85.964249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [85.964439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [85.964612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [85.964856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [85.964974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [85.965169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [85.965159] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [85.965326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [85.965405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [85.965487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [85.965692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [85.965908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [85.966113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [85.966308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.966525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [85.966741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [85.967476] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [85.967668] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.000170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.000759] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.001387] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469]

<7> [86.001264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.004156] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.004586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [86.005181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [86.005453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [86.005739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.005984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.006273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.006499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.006801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.006996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.007223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.007431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.007653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.007835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.008003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.008159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.008342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.008585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.008997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.009224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.009428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.009638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.010405] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.010604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.015199] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470]

<7> [86.016375] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.047071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.047528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [86.048036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [86.048186] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.048368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [86.048772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.048772] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.049088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.049261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.049400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.049777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.050123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.050575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.051067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.051484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.051917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.052336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.053321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.053751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.080267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.080550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [86.080844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [86.081029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [86.080980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.081203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.081292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.081399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.081557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.081581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.081827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.082019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.082283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.082543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.082846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.083084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.083319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.084030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.084293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.113567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.113870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [86.114088] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [86.114270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [86.114446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.114671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.114801] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.114890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.115057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.115144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.115240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.115427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.115633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.115870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [86.116059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [86.116226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [86.116389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.116550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.116769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.116932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.117101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.117376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.117660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.117974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.118258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.118537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.119361] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.119656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.147250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.147645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [86.147755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.147913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [86.148141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [86.148152] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.148358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.148477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.148566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.148841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.149030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.149286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.149724] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.149989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [86.150191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [86.150366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [86.150540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.150770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.150990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.151198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.151389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.151707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.152002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.152321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.152610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.152877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.153746] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.154015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.180357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.180758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [86.180854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.181063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [86.181300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [86.181283] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.181528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.181676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.181806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.182023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.182266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.182488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.182954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.183198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [86.183391] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [86.183577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [86.183830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.184012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.184221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.184399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.184601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.184901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.185199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.185492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.185865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.186136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.186925] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.187193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.213668] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.214070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [86.214371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [86.214655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [86.214802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.214886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.215155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.215215] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.215380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.215614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.215568] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.215857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.216408] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.216700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [86.216946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [86.217152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [86.217353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.217550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.217855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.218054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.218263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.218596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.218947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.219241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.219528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.219859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.220934] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.221227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.230327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.263538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.263881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [86.264091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [86.264286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [86.264474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.264704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.264889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.264845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.265093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.265165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.265315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.265435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.265582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.265831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.266078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.266338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.266772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.267512] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.267844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.296842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.297083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [86.297301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [86.297481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [86.297706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.297884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.297830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.298080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.298146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.298255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.298410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.298435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.298706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.298949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.299201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.299502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.299781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.300515] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.300841] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.330152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.330379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [86.330632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [86.330804] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [86.330789] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.330976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.331148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.331129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.331321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.331435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.331492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.331759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.332092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.332401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.332700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.332962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.333225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.334012] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.334269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.363731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.363973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [86.364160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [86.364323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [86.364486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.364813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.364821] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.364982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.365170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.365151] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.365381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [86.365447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.365642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.365879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.366121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.366367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.366644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.367340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.367600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.396786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [86.397009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [86.397213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [86.397399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [86.397596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.397756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.397725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.397949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.398119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.398058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.398293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [86.398341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.398568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [86.398818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [86.399054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.399284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [86.399622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [86.400282] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.400556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.430293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [86.430470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [86.430696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [86.430859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.430838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.431015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.431178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.431161] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.431373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.431441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.431647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [86.431813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [86.431969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [86.432117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [86.432258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.432396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.432553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.432723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.432919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.433190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.433445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.433729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.434028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.434298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.435047] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.435305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.436053] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [86.436260] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [86.463567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.463791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.463980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.464164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.464346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.464578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.464584] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.464782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.464920] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.465062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.465221] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.465342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.465645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.465920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.466199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.466923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.467208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.497761] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471]

<7> [86.497606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.498028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.498410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.521745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [86.521994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [86.522194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.522374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.522628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.522796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.523021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.523260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.523475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.523713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.523909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.524101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.524835] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.525022] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.546898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.547134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.547342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.547606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.547615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.547815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.547996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.548052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.548285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.548299] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.548566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.548825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.549098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.549375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.549719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.550549] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.550840] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.580570] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [86.580656] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.580859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [86.581118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.581142] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.581371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.581581] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.581663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.581902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.582232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.582623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.582960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.583350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.583731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.584066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.584968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.585324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.613531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [86.613792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [86.614009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.614223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.614435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.614740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.614876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.614975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.615254] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.615285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.615621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.615613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.615954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.616224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.616516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.617311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.617623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.646842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [86.647026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [86.647202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.647371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.647590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.647782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.647742] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.647977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.648064] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.648314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [86.648329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.648487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [86.648640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.648818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.648985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.649151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.649305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.649570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.649804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.650035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.650264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.650507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.651088] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.651326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.680183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.680385] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.680627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.680669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.680809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.681024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.681026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.681197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.681333] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.681389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.681826] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.682032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.682209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.682372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.682575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.682733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.682899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.683167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.683432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.683748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.684040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.684320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.685108] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.685388] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.713586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [86.713862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [86.714078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.714283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.714521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.714653] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.714715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.714974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.715008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.715343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.715396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [86.715671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [86.715855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.716034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.716213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.716425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.716682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.717097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [86.717263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [86.717420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.717634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.717792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.717981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.718157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.718408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.718689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.718928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.719170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.719433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.720186] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.720435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.746845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.747118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.747353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.747647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.747775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.747864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.748115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.748158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.748378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.748517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.748882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.749084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.749278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.749491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.749679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.749885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.750078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.750513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [86.750704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [86.750888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.751065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.751243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.751419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.751673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.751965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.752238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.752525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.752844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.753099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.753881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.754135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.780333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [86.780626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [86.780758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.780832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.781016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.781084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.781194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [86.781351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.781399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [86.781664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [86.781938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [86.782200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [86.782466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.782769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [86.783017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [86.783703] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.783955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.813496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [86.813747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [86.813969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.814183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.814394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.814679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.814834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.814921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.815246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.815245] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.815615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.815646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.815949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.816245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.816554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.817367] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.817707] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.846821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [86.847014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [86.847199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.847451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [86.847630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [86.847597] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.847804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [86.847974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.847951] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.848138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.848302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.848270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.848502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.849206] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.849501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.896971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.897328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.897676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.897914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.897828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.898141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.898247] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.898371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.898656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.898738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.899103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.899445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.899764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.900082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.900462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.901390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.901775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.930484] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.930887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.931197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.932586] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472]

<7> [86.947894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [86.948138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [86.948342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.948626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [86.948819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [86.949024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [86.949224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [86.949500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [86.949743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [86.949982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.950237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [86.950660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [86.951333] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.951592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [86.980208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [86.980511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [86.980617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [86.980719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [86.980926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [86.981002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [86.981135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [86.981344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [86.981354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [86.981647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [86.981966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [86.982301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [86.982734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.983087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [86.983474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [86.984562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [86.984912] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.013694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [87.013908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [87.014110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.014337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.014619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.014779] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.014874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.015152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [87.015209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.015529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [87.015649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.015868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [87.016178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.016508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.016807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [87.017648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.017967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.046756] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [87.047013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [87.047216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.047458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.047646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.047595] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.047853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.047929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.048047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [87.048208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.048295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.048572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.048813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.049059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.049318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.050048] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.050296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.080110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [87.080306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [87.080549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.080734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.080680] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.080917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.081033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.081122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.081314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.081326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [87.081663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [87.081920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [87.082166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.082422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.082687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [87.083239] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.083533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.113419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [87.113623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [87.113806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.113987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.114173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.114430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.114562] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.114646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [87.114937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.114946] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.115202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.115267] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.115605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.115877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.116119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.116724] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.116982] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.146726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [87.146904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [87.147065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.147227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.147431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.147597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.147578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.147786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [87.147909] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.148033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [87.148206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.148287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [87.148562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.148803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.149041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [87.149699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.149950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.180079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [87.180283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [87.180541] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.180676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.180771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.180961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.181055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.181139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.181354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [87.181410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.181643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.181949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.182259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.182660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.182970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.183779] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.184066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.213705] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [87.213925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [87.214147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.214412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.214633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.214553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.214850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.215002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.215146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [87.215429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.215702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [87.215949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [87.216153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.216353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.216538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.216718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.216941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [87.217255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [87.217608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [87.217919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.218259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [87.218628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [87.219527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.219850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.246830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [87.247117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [87.247396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.247515] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.247617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.247832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.247896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.248081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.248220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.248317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [87.248818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [87.249023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [87.249217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.249497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.249687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.249870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.250063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [87.250373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.250715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.251002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.251289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.251655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.252513] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.252829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.280471] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.280884] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.281126] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473]

<7> [87.281236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.306654] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.307014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [87.307341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [87.307560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [87.307769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.307969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.308162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [87.308543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [87.308710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.308870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.309052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [87.309201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [87.309375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.309517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.309652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.309802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.309967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.310268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.310452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [87.310573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [87.310689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [87.310798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.310909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.311021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [87.311132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [87.311238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.311363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.311462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [87.311560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [87.311655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.311746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.311836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.311927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.312023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.312182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.312339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.312506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.312667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.312804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.313401] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.313542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.329769] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [87.369338] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.369499] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.369617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.369753] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474]

<7> [87.379732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.380270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.380437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.413627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.414215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [87.414953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [87.414988] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.415420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [87.415701] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.415772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.416156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.416225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.416554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.416907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.417298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.418069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.418425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [87.418687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [87.418937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [87.419174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.419499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.419788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.420044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.420335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.420663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.420985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.421352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.421697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.422004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.422738] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.423002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.446848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.447256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [87.447702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [87.447845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.447964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [87.448193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.448271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.448556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.448693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.448794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.449011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.449295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.449655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.450007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.450437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.450814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.451154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.452207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.452564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.480063] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.480438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [87.480546] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.480729] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [87.480947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [87.480929] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.481148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.481263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.481372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.481558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.481786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.482022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.482322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.482584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.482837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.483126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.483391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.484128] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.484442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.513551] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.513803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [87.513990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [87.514180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [87.514425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.514618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.514567] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.514849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.514948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.515061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.515349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.515359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.515680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.515995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.516317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.516604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.516884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.517802] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.518121] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.546631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.546914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [87.547151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [87.547377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [87.547550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.547535] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.547749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.547846] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.547912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.548072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.548117] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.548281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.548548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.548808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.549136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.549442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.549761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.550578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.550881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.580037] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.580376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [87.580456] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.580602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [87.580814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [87.580864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.581018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.581229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.581204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.581491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.581678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.581905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.582182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.582484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.582750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.583007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.583264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.584157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.584450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.596901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.629956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.630196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [87.630498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [87.630527] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.630672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [87.630842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.630857] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.631013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.631152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.631222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.631454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.631652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.631925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.632213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.632529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.632851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.633110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.633828] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.634102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.663347] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.663601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [87.663793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [87.663976] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [87.664197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.664450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.664635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.664582] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.664816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.664939] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.665021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.665272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.665676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.665923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.666155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.666431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.666657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.667393] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.667657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.696586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.696832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [87.697058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [87.697343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [87.697418] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.697536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.697749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.697773] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.697926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.698066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.698122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.698360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.698662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.698912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.699204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.699491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.699782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.700503] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.700781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.730189] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.730535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [87.730609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.730770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [87.730952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [87.730962] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.731124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.731328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.731301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.731496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.731700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.731913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [87.732185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [87.732501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [87.732812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.733073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [87.733363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [87.734067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.734382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.763412] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.763666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [87.763861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [87.764048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [87.764312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.764496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.764439] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.764702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.764798] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.764892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.765082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [87.765102] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.765385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [87.765676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [87.765954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.766223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [87.766480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [87.767335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.767618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.797352] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.797806] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475]

<7> [87.797767] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.798129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.822071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.822368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [87.822552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [87.822711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [87.822868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.823022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.823170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.823450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.823592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.823746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.823875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.823995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.824112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.824246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.824355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.824455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.824575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.824819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.824966] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [87.825081] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [87.825178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [87.825318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.825409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.825494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.825575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.825657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.825738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.825820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.825899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.825976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.826052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.826127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.826218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.826295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.826418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.826535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.826652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.826765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.826876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.828515] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.828645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.830907] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476]

<7> [87.843511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.863403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.863669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.863863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.864047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.864317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.864276] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.864499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.864575] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.864663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.864820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.864826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.864992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.865336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.865524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.865662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.865796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.865928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.866080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.866257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.866388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.866542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.866750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.866943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.867126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.867327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.867498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.867970] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.868163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.896701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.897060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [87.897374] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.897424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [87.897650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [87.897698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.897872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.897996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.898098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.898372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.898608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.898879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.899458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.899723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [87.899957] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [87.900201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [87.900422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.900639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [87.900855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [87.901066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [87.901326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.901651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.901973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.902311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.902600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.902887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.903691] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.903957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.929987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.930348] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.930368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.930655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.930660] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.930874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.930938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.931083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.931423] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.931625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.931870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.932095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.932648] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.932892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [87.933105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [87.933349] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [87.933534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.933738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [87.933917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [87.934095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [87.934335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.934664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.934965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.935285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.935588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [87.935877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [87.936675] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.936971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.963595] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.963926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [87.964241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [87.964314] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.964487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [87.964725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.964732] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.964973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.965090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.965219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [87.965443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [87.965745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [87.966066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [87.966405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [87.966736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.967029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [87.967355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [87.968176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [87.968479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [87.996679] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [87.997042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [87.997412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [87.997658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [87.997745] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [87.997890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [87.998116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [87.998173] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [87.998400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [87.998531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [87.998620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [87.998921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [87.999287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [87.999620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [87.999945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.000282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.000591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [88.001557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.001915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.030017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.030390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [88.030483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.030645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [88.030866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [88.030863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.031077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.031239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.031329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [88.031536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [88.031724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [88.031935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [88.032229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [88.032510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [88.032780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.033100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [88.034294] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.034560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.046992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.079934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.080279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [88.080282] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.080557] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [88.080664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.080763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [88.080963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.080989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.081237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [88.081433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [88.081651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [88.081856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [88.082145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [88.082427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [88.082682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.082930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.083182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [88.083833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.084087] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.113361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.113659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [88.113933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [88.114178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [88.114376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.114312] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.114569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [88.114691] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.114759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [88.114984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [88.115013] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.115250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [88.115534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [88.115804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [88.116064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.116349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.116590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [88.117378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.117656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.146552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.146823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [88.147071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [88.147353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [88.147450] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.147547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.147758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [88.147833] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.147950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [88.148171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [88.148198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.148406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [88.148723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [88.149032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [88.149367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.149667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.149961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [88.150852] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.151158] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.180164] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.180180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.180428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [88.180561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.180672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [88.180866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [88.180888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.181050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.181260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [88.181432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [88.181599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [88.181791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [88.182059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [88.182346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [88.182615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.182864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [88.183093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [88.183883] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.184162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.213223] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.213471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [88.213658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [88.213841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [88.214056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.214309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [88.214492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [88.214445] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.214667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [88.214825] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.214864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [88.215150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [88.215176] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.215419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [88.215681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.215942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [88.216275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [88.216970] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.217243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.246561] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [88.246923] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [88.247285] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [88.247420] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.247657] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [88.247831] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.247975] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [88.248237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [88.248405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [88.248748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [88.249085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [88.249459] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [88.249824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [88.250195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [88.250494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [88.250830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [88.251161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [88.251535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [88.251856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [88.252251] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [88.252601] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled

<7> [88.252911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [88.253235] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [88.253524] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14

<7> [88.253811] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [88.254131] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [88.254445] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [88.254757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [88.255071] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [88.255442] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [88.255722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [88.255989] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [88.256289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [88.256573] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [88.256819] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [88.257064] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [88.257344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [88.257580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [88.257801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [88.258016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [88.258246] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [88.258444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [88.258644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [88.258830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [88.259014] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [88.259218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [88.259391] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [88.259561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [88.259724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [88.259883] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [88.260035] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [88.260214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [88.260361] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [88.260530] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [88.260683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [88.260820] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [88.260957] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261366] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [88.261492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [88.261631] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [88.261991] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [88.262116] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [88.262231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes

<7> [88.262342] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [88.262450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0

<7> [88.262555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no

<7> [88.262660] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [88.262762] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes

<7> [88.262865] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [88.262971] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0

<7> [88.263118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [88.263238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [88.263404] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1

<7> [88.263553] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on

<7> [88.263687] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [88.279690] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [88.280935] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [88.281071] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [88.283548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0

<7> [88.283657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [88.283751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0

<7> [88.283845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [88.283938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [88.284347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [88.284716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [88.284977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [88.285118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [88.285248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [88.285370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [88.285488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [88.285601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [88.285934] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<6> [88.300219] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS

<7> [88.300953] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051

<7> [88.301144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [88.301279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [88.301406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87

<7> [88.301530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88

<7> [88.301667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1

<7> [88.301845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [88.302007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [88.302183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [88.302331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [88.302475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [88.312965] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [88.314640] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<6> [88.314913] [IGT] kms_rotation_crc: exiting, ret=0

<6> [88.330662] Console: switching to colour frame buffer device 180x56

<7> [88.365219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [88.365677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [88.366100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

Results for igt@kms_rotation_crc@multiplane-rotation-cropping-top