Result: 1 Warning(s)
i915_display_info2 igt_runner2 results2.json results2-xe-load.json i915_display_info_post_exec2 boot2 dmesg2
| Detail | Value |
|---|---|
| Duration | unknown |
| Hostname |
shard-lnl-5 |
| Igt-Version |
IGT-Version: 2.2-gf76e05461 (x86_64) (Linux: 6.18.0-lgci-xe-xe-4182-278f5507f31b5bb22+ x86_64) |
| Out |
Using IGT_SRANDOM=1764747656 for randomisation Opened device: /dev/dri/card0 Starting subtest: s2idle-basic-exec [cmd] rtcwake: assuming RTC uses UTC ... [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Wed Dec 3 07:41:13 2025 Subtest s2idle-basic-exec: SUCCESS (1.843s) This test caused an abort condition: Kernel badly tainted (0x240, 0x200) (check dmesg for details): TAINT_WARN: WARN_ON has happened. |
| Err |
Starting subtest: s2idle-basic-exec Subtest s2idle-basic-exec: SUCCESS (1.843s) |
| Dmesg |
<6> [161.079256] Console: switching to colour dummy device 80x25
<6> [161.079414] [IGT] xe_pm: executing
<7> [162.092747] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 turning VDD off
<7> [162.093300] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<6> [162.120528] [IGT] xe_pm: starting subtest s2idle-basic-exec
<6> [162.249412] PM: suspend entry (s2idle)
<6> [162.253966] Filesystems sync: 0.004 seconds
<6> [162.272031] Freezing user space processes
<4> [162.273755] ------------[ cut here ]------------
<4> [162.274108] WARNING: CPU: 0 PID: 3002 at kernel/freezer.c:139 __set_task_frozen+0x7f/0xb0
<4> [162.274126] Modules linked in: snd_hda_codec_intelhdmi snd_hda_codec_hdmi xe drm_gpuvm drm_gpusvm_helper drm_ttm_helper ttm gpu_sched drm_suballoc_helper drm_exec drm_buddy drm_display_helper cec rc_core drm_kunit_helpers i2c_algo_bit kunit hid_sensor_custom hid_sensor_hub hid_generic intel_ishtp_hid hid intel_uncore_frequency intel_uncore_frequency_common cmdlinepart spi_nor x86_pkg_temp_thermal mtd mei_gsc_proxy intel_powerclamp intel_rapl_msr ucsi_acpi wmi_bmof coretemp typec_ucsi typec kvm_intel overlay kvm irqbypass polyval_clmulni ghash_clmulni_intel aesni_intel snd_hda_intel processor_thermal_device_pci rapl processor_thermal_device processor_thermal_wt_hint platform_temperature_control snd_intel_dspcfg snd_hda_codec intel_cstate processor_thermal_soc_slider snd_hda_core snd_hwdep platform_profile processor_thermal_rfim snd_pcm r8169 snd_timer spi_intel_pci processor_thermal_rapl realtek spi_intel snd intel_rapl_common intel_ish_ipc mei_me processor_thermal_wt_req soundcore idma64 processor_thermal_power_floor
<4> [162.274582] intel_ishtp mei processor_thermal_mbox intel_vpu thunderbolt binfmt_misc intel_pmc_core int3403_thermal video int340x_thermal_zone intel_skl_int3472_tps68470 tps68470_regulator clk_tps68470 pmt_telemetry pmt_discovery pmt_class wmi int3400_thermal intel_hid intel_pmc_ssram_telemetry sparse_keymap acpi_thermal_rel intel_skl_int3472_discrete intel_vsec pinctrl_intel_platform acpi_pad intel_skl_int3472_common acpi_tad nls_iso8859_1 dm_multipath msr nvme_fabrics fuse efi_pstore nfnetlink autofs4
<4> [162.274707] CPU: 0 UID: 0 PID: 3002 Comm: rtcwake Tainted: G U 6.18.0-lgci-xe-xe-4182-278f5507f31b5bb22+ #1 PREEMPT(voluntary)
<4> [162.274719] Tainted: [U]=USER
<4> [162.274724] Hardware name: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D99.2508051732 08/05/2025
<4> [162.274729] RIP: 0010:__set_task_frozen+0x7f/0xb0
<4> [162.274741] Code: c4 00 20 00 00 74 06 41 f6 c4 03 74 40 41 81 e4 00 40 00 00 75 16 8b 15 13 bc 47 02 85 d2 74 0c 8b 83 30 0f 00 00 85 c0 74 02 <0f> 0b 8b 43 18 c7 43 18 00 80 00 00 89 43 1c b8 00 80 00 00 5b 41
<4> [162.274748] RSP: 0018:ffffc9000f9d7a40 EFLAGS: 00010002
<4> [162.274758] RAX: 0000000000000002 RBX: ffff8881281734c0 RCX: 0000000000000000
<4> [162.274764] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000
<4> [162.274769] RBP: ffffc9000f9d7a50 R08: 0000000000000000 R09: 0000000000000000
<4> [162.274774] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
<4> [162.274778] R13: 0000000000000000 R14: ffff888128174310 R15: ffff8881281734c0
<4> [162.274784] FS: 000076eb7f469740(0000) GS:ffff8888db2ea000(0000) knlGS:0000000000000000
<4> [162.274790] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [162.274796] CR2: 00007f2b80c0b048 CR3: 000000012900b003 CR4: 0000000000f72ef0
<4> [162.274802] PKRU: 55555554
<4> [162.274807] Call Trace:
<4> [162.274811] <TASK>
<4> [162.274818] ? __pfx___set_task_frozen+0x10/0x10
<4> [162.274829] task_call_func+0x6d/0x120
<4> [162.274843] ? cgroup_freezing+0x89/0x200
<4> [162.274863] freeze_task+0x98/0x100
<4> [162.274880] try_to_freeze_tasks+0xd2/0x440
<4> [162.274907] freeze_processes+0x56/0xd0
<4> [162.274919] pm_suspend+0x209/0x7f0
<4> [162.274935] state_store+0x6e/0xe0
<4> [162.274951] kobj_attr_store+0x12/0x40
<4> [162.274964] sysfs_kf_write+0x4d/0x80
<4> [162.274980] kernfs_fop_write_iter+0x188/0x240
<4> [162.274999] vfs_write+0x283/0x540
<4> [162.275034] ksys_write+0x6f/0xf0
<4> [162.275048] __x64_sys_write+0x19/0x30
<4> [162.275056] x64_sys_call+0x79/0x26a0
<4> [162.275066] do_syscall_64+0x93/0xd30
<4> [162.275078] ? __x64_sys_openat+0x54/0xa0
<4> [162.275095] ? do_syscall_64+0x1b7/0xd30
<4> [162.275108] ? __might_fault+0x89/0xb0
<4> [162.275119] ? __might_fault+0x53/0xb0
<4> [162.275131] ? __rseq_handle_notify_resume+0x1f7/0x5f0
<4> [162.275144] ? iput+0x1a4/0x330
<4> [162.275157] ? sync_bdevs+0x148/0x170
<4> [162.275175] ? trace_hardirqs_off+0x5a/0xd0
<4> [162.275182] ? local_irq_disable_exit_to_user+0x34/0x50
<4> [162.275191] ? do_syscall_64+0x1b7/0xd30
<4> [162.275196] ? do_user_addr_fault+0x2fd/0x8e0
<4> [162.275205] ? irqentry_exit_to_user_mode+0xf4/0x320
<4> [162.275214] ? irqentry_exit+0x77/0xb0
<4> [162.275217] ? exc_page_fault+0xbd/0x2c0
<4> [162.275226] entry_SYSCALL_64_after_hwframe+0x76/0x7e
<4> [162.275230] RIP: 0033:0x76eb7f31c574
<4> [162.275236] Code: c7 00 16 00 00 00 b8 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 80 3d d5 ea 0e 00 00 74 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 55 48 89 e5 48 83 ec 20 48 89
<4> [162.275239] RSP: 002b:00007ffe5bf930d8 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
<4> [162.275244] RAX: ffffffffffffffda RBX: 0000000000000007 RCX: 000076eb7f31c574
<4> [162.275246] RDX: 0000000000000007 RSI: 00005636a57f14a0 RDI: 000000000000000b
<4> [162.275249] RBP: 00007ffe5bf93100 R08: 000076eb7f403b20 R09: 0000000000000000
<4> [162.275251] R10: 0000000000000001 R11: 0000000000000202 R12: 0000000000000007
<4> [162.275253] R13: 00005636a57f14a0 R14: 00005636a57ef450 R15: 000076eb7f401ee0
<4> [162.275273] </TASK>
<4> [162.275276] irq event stamp: 10502
<4> [162.275278] hardirqs last enabled at (10501): [<ffffffff828ca671>] _raw_spin_unlock_irqrestore+0x51/0x80
<4> [162.275285] hardirqs last disabled at (10502): [<ffffffff828ca2f4>] _raw_spin_lock_irqsave+0x74/0x80
<4> [162.275290] softirqs last enabled at (10322): [<ffffffff813d3d9f>] __irq_exit_rcu+0x13f/0x160
<4> [162.275296] softirqs last disabled at (10289): [<ffffffff813d3d9f>] __irq_exit_rcu+0x13f/0x160
<4> [162.275300] ---[ end trace 0000000000000000 ]---
<6> [162.276804] Freezing user space processes completed (elapsed 0.004 seconds)
<6> [162.276857] OOM killer disabled.
<6> [162.276860] Freezing remaining freezable tasks
<6> [162.278436] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<7> [162.348594] GFP mask restricted
<6> [162.370605] r8169 0000:7f:00.0 enp127s0: Link is Down
<7> [162.416093] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [162.416441] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010
<7> [162.428704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [162.431803] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [162.433911] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [162.434486] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [162.435061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B
<7> [162.435997] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C
<7> [162.436759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D
<7> [162.437204] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
<7> [162.438135] xe 0000:00:02.0: [drm:drm_client_dev_suspend] fbdev: ret=0
<7> [162.439854] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [162.440242] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [162.440564] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [162.440879] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [162.441157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [162.441436] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [162.441703] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [162.441951] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [162.442196] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [162.442431] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [162.442665] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [162.442884] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [162.443104] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [162.443309] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [162.443515] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [162.443714] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [162.443908] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [162.444100] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [162.444285] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [162.444460] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [162.444633] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [162.444803] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [162.444967] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [162.445130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [162.445287] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [162.445438] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [162.445588] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [162.445736] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [162.445880] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [162.446025] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [162.446167] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [162.446301] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [162.446433] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [162.446562] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [162.446696] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [162.446821] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [162.446941] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [162.447060] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [162.447181] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:89:pipe A] fastset requirement not met, forcing full modeset
<7> [162.447300] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:89:pipe A] releasing DPLL 0
<7> [162.447522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [162.447628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:89:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [162.447770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [162.447853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [162.447930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [162.448008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [162.448085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [162.448160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [162.448267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:89:pipe A] data rate 0 num active planes 0
<7> [162.448389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [162.448504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [162.448616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [162.448828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [162.448948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [162.449455] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:89:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [162.449650] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [162.449770] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [162.449879] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [162.449985] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [162.450153] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:89:pipe A] enable: no [modeset]
<7> [162.450273] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [162.450381] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [162.450488] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [162.450594] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [162.450706] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [162.450813] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [162.451106] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [162.451548] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 turning VDD on
<7> [162.451712] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [162.452467] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [162.452611] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [162.660724] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:211:eDP-1] set backlight PWM = 0
<7> [162.662587] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [162.669411] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 turn panel power off
<7> [162.669459] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [162.669951] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [162.670423] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [162.722295] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [162.730800] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [162.731318] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:89:pipe A]
<7> [162.731552] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:210:DDI A/PHY A]
<7> [162.732085] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:210:DDI A/PHY A]
<7> [162.732822] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [162.733364] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [162.734349] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:210:DDI A/PHY A]
<7> [162.734772] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DDI TC1/PHY TC1]
<7> [162.735132] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:221:DP-MST A]
<7> [162.735448] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:222:DP-MST B]
<7> [162.735769] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:223:DP-MST C]
<7> [162.736075] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DDI TC2/PHY TC2]
<7> [162.736380] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:233:DP-MST A]
<7> [162.736697] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:234:DP-MST B]
<7> [162.737000] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:235:DP-MST C]
<7> [162.737303] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DDI TC3/PHY TC3]
<7> [162.737605] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:241:DP-MST A]
<7> [162.737918] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:242:DP-MST B]
<7> [162.738217] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:243:DP-MST C]
<7> [162.738518] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:211:eDP-1]
<7> [162.739126] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [162.739400] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [162.739689] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [162.740201] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:89:pipe A]
<7> [162.740703] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [162.741149] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [162.741457] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [162.741886] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800010 0x9a00071)
<7> [162.747811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC
<7> [162.748090] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D
<7> [162.748333] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [162.748573] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [162.748800] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C
<7> [162.749004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [162.749199] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [162.749388] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [162.749564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [162.749751] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [162.749979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [162.750198] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x0
<7> [162.750731] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 0 (mbus joined: no)
<7> [162.750873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_1
<7> [162.751033] xe 0000:00:02.0: [drm:bxt_enable_dc9 [xe]] Enabling DC9
<7> [162.751441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 08
<7> [162.764305] PM: suspend of devices complete after 415.709 msecs
<7> [162.764324] PM: start suspend of devices complete after 485.753 msecs
<7> [162.775548] PM: late suspend of devices complete after 11.218 msecs
<6> [162.793578] ACPI: EC: interrupt blocked
<7> [162.983574] PM: noirq suspend of devices complete after 205.455 msecs
<6> [162.983648] ACPI: \_SB_.PR00: LPI: Device not power manageable
<6> [162.983661] ACPI: \_SB_.PR01: LPI: Device not power manageable
<6> [162.983665] ACPI: \_SB_.PR02: LPI: Device not power manageable
<6> [162.983669] ACPI: \_SB_.PR03: LPI: Device not power manageable
<6> [162.983673] ACPI: \_SB_.PR04: LPI: Device not power manageable
<6> [162.983677] ACPI: \_SB_.PR05: LPI: Device not power manageable
<6> [162.983681] ACPI: \_SB_.PR06: LPI: Device not power manageable
<6> [162.983685] ACPI: \_SB_.PR07: LPI: Device not power manageable
<6> [162.983695] ACPI: \_SB_.PC00.IPU0: LPI: Device not power manageable
<6> [162.983700] ACPI: \_SB_.PC00.NPU0: LPI: Device not power manageable
<6> [162.983704] ACPI: \_SB_.PC00.HECI: LPI: Device not power manageable
<6> [162.983709] ACPI: \_SB_.PC00.ISHD: LPI: Device not power manageable
<6> [162.983714] ACPI: \_SB_.PC00.TRP0: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [162.983720] ACPI: \_SB_.PC00.TRP1: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [162.983724] ACPI: \_SB_.PC00.TRP2: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [162.984902] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<6> [162.989541] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 ms entry
<7> [162.992605] PM: Triggering wakeup from IRQ 9
<6> [163.000678] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [163.000682] PM: suspend-to-idle
<7> [163.000876] ACPI: EC: ACPI EC GPE status set
<7> [163.000915] ACPI: PM: Rearming ACPI SCI for wakeup
<7> [177.568696] Timekeeping suspended for 14.710 seconds
<7> [177.568830] PM: Triggering wakeup from IRQ 9
<7> [177.570137] ACPI: PM: ACPI fixed event wakeup
<7> [177.570146] PM: resume from suspend-to-idle
<6> [177.606675] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [177.613121] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 ms exit
<6> [177.614089] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [177.614746] ACPI: EC: interrupt unblocked
<7> [178.038002] PM: noirq resume of devices complete after 423.924 msecs
<6> [178.049704] pci 0000:00:05.0: Setting to D3hot
<7> [178.065686] PM: early resume of devices complete after 24.609 msecs
<7> [178.067352] xe 0000:00:02.0: [drm:gen9_sanitize_dc_state [xe]] Resetting DC state tracking from 08 to 08
<7> [178.067833] xe 0000:00:02.0: [drm:bxt_disable_dc9 [xe]] Disabling DC9
<7> [178.068287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 08 to 00
<7> [178.068781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00
<7> [178.069227] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_1
<7> [178.070004] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [178.070404] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Sanitizing cdclk programmed by pre-os
<7> [178.073318] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [178.073704] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [178.074047] xe 0000:00:02.0: [drm:icl_display_core_init [xe]] Unknown memory configuration; disabling address buddy logic.
<7> [178.085103] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [178.085314] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [178.085515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00
<7> [178.085746] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [178.085968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [178.086176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B
<7> [178.086386] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C
<7> [178.086583] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D
<7> [178.087578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
<6> [178.128363] nvme nvme0: 8/0/0 default/read/poll queues
<7> [178.131590] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [178.132186] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [178.132577] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [178.132859] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [178.133120] xe 0000:00:02.0: [drm:intel_cdclk_read_hw [xe]] Current CDCLK 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [178.133849] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:89:pipe A] hw state readout: disabled
<7> [178.134181] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:148:pipe B] hw state readout: disabled
<7> [178.134478] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:207:pipe C] hw state readout: disabled
<7> [178.134704] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] hw state readout: disabled, pipe A
<7> [178.134930] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A
<7> [178.135151] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A
<7> [178.135377] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A
<7> [178.135597] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A
<7> [178.135815] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] hw state readout: disabled, pipe A
<7> [178.136032] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:92:plane 1B] hw state readout: disabled, pipe B
<7> [178.136249] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:102:plane 2B] hw state readout: disabled, pipe B
<7> [178.136478] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:112:plane 3B] hw state readout: disabled, pipe B
<7> [178.136680] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:122:plane 4B] hw state readout: disabled, pipe B
<7> [178.136881] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:132:plane 5B] hw state readout: disabled, pipe B
<7> [178.137082] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:142:cursor B] hw state readout: disabled, pipe B
<7> [178.137282] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:151:plane 1C] hw state readout: disabled, pipe C
<7> [178.137492] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:161:plane 2C] hw state readout: disabled, pipe C
<7> [178.137693] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:171:plane 3C] hw state readout: disabled, pipe C
<7> [178.137887] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:181:plane 4C] hw state readout: disabled, pipe C
<7> [178.138073] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:191:plane 5C] hw state readout: disabled, pipe C
<7> [178.138259] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:201:cursor C] hw state readout: disabled, pipe C
<7> [178.138462] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:210:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [178.138703] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [178.138880] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:219:DDI TC1/PHY TC1] hw state readout: disabled, pipe A
<7> [178.139051] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:221:DP-MST A] hw state readout: disabled, pipe A
<7> [178.139213] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:222:DP-MST B] hw state readout: disabled, pipe B
<7> [178.139378] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:223:DP-MST C] hw state readout: disabled, pipe C
<7> [178.139544] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [178.139699] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:231:DDI TC2/PHY TC2] hw state readout: disabled, pipe A
<7> [178.139854] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:233:DP-MST A] hw state readout: disabled, pipe A
<7> [178.140006] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:234:DP-MST B] hw state readout: disabled, pipe B
<7> [178.140154] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:235:DP-MST C] hw state readout: disabled, pipe C
<7> [178.140303] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [178.140455] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:239:DDI TC3/PHY TC3] hw state readout: disabled, pipe A
<7> [178.140604] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:241:DP-MST A] hw state readout: disabled, pipe A
<7> [178.140745] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:242:DP-MST B] hw state readout: disabled, pipe B
<7> [178.140879] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:243:DP-MST C] hw state readout: disabled, pipe C
<7> [178.141022] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [178.141179] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [178.141337] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TBT PLL hw state readout: pipe_mask 0x0, on 1
<7> [178.141492] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [178.141645] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [178.141795] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [178.141931] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [178.142100] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:211:eDP-1] hw state readout: disabled
<7> [178.142230] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:220:DP-1] hw state readout: disabled
<7> [178.142355] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:232:DP-2] hw state readout: disabled
<7> [178.142477] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:240:DP-3] hw state readout: disabled
<7> [178.142590] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] min_cdclk 0 kHz
<7> [178.142703] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] min_cdclk 0 kHz
<7> [178.142811] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] min_cdclk 0 kHz
<7> [178.142915] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] min_cdclk 0 kHz
<7> [178.143018] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] min_cdclk 0 kHz
<7> [178.143121] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] min_cdclk 0 kHz
<7> [178.143223] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:89:pipe A] min_cdclk 0 kHz
<7> [178.143325] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:92:plane 1B] min_cdclk 0 kHz
<7> [178.143424] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:102:plane 2B] min_cdclk 0 kHz
<7> [178.143521] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:112:plane 3B] min_cdclk 0 kHz
<7> [178.143617] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:122:plane 4B] min_cdclk 0 kHz
<7> [178.143712] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:132:plane 5B] min_cdclk 0 kHz
<7> [178.143807] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:142:cursor B] min_cdclk 0 kHz
<7> [178.143899] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:148:pipe B] min_cdclk 0 kHz
<7> [178.143990] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:151:plane 1C] min_cdclk 0 kHz
<7> [178.144079] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:161:plane 2C] min_cdclk 0 kHz
<7> [178.144168] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:171:plane 3C] min_cdclk 0 kHz
<7> [178.144255] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:181:plane 4C] min_cdclk 0 kHz
<7> [178.144344] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:191:plane 5C] min_cdclk 0 kHz
<7> [178.144430] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:201:cursor C] min_cdclk 0 kHz
<7> [178.144517] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:207:pipe C] min_cdclk 0 kHz
<7> [178.144611] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:89:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [178.144694] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:148:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [178.144769] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:207:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [178.144843] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 0 num active planes 0
<7> [178.144962] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0
<7> [178.145077] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0
<7> [178.145214] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: disabled, CMTG B: disabled, Transcoder A secondary: no, Transcoder B secondary: no
<7> [178.145379] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:89:pipe A] enable: no [setup_hw_state]
<7> [178.145489] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:148:pipe B] enable: no [setup_hw_state]
<7> [178.145599] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:207:pipe C] enable: no [setup_hw_state]
<7> [178.145708] xe 0000:00:02.0: [drm:intel_dpll_sanitize_state [xe]] TBT PLL enabled but not in use, disabling
<7> [178.145907] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:211:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [178.146042] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:210:DDI A/PHY A][CRTC:89:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000
<7> [178.146145] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [178.146274] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:89:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [178.146421] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:210:DDI A/PHY A] [CRTC:89:pipe A]
<7> [178.146534] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [178.146642] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [178.146745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [178.146849] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [178.146952] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [178.147056] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [178.147157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [178.147259] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [178.147364] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [178.147465] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [178.147565] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [178.147665] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [178.147766] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [178.147867] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [178.147969] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [178.148070] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [178.148172] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [178.148273] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [178.148377] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [178.148477] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [178.148578] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [178.148678] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [178.148779] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [178.148880] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [178.148981] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [178.149081] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [178.149182] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [178.149283] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [178.149387] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [178.149489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [178.149589] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [178.149690] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [178.149793] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in intel_dpll (expected 0000000000000000, found ffff88814e19b2f0)
<7> [178.149896] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in dpll_hw_state
<7> [178.149997] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [178.150098] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [178.150200] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [178.150300] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [178.150403] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [178.150505] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [178.150605] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [178.150705] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [178.150806] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [178.150906] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [178.151006] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [178.151106] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [178.151207] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [178.151307] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [178.151411] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [178.151511] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [178.151611] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [178.151711] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [178.151812] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [178.151912] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [178.152013] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [178.152113] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [178.152213] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [178.152313] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [178.152428] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [178.152529] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [178.152630] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [178.152730] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [178.152832] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [178.152932] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [178.153033] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [178.153134] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:89:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [178.153238] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:89:pipe A] fastset requirement not met, forcing full modeset
<7> [178.153343] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:148:pipe B] fastset requirement not met in dpll_hw_state
<7> [178.153442] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [178.153542] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [178.153642] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [178.153742] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [178.153843] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [178.153943] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [178.154043] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [178.154143] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [178.154243] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [178.154346] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [178.154445] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [178.154546] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [178.154646] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [178.154746] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [178.154846] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [178.154946] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [178.155046] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [178.155147] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [178.155247] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [178.155349] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [178.155449] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [178.155551] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [178.155650] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [178.155751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [178.155851] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [178.155952] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [178.156052] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [178.156153] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [178.156254] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:148:pipe B] fastset requirement not met, forcing full modeset
<7> [178.156362] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:207:pipe C] fastset requirement not met in dpll_hw_state
<7> [178.156463] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [178.156563] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [178.156663] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [178.156763] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [178.156863] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [178.156963] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [178.157063] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [178.157163] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [178.157263] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [178.157366] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [178.157466] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [178.157566] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [178.157666] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [178.157766] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [178.157866] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [178.157966] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [178.158066] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [178.158166] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [178.158266] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [178.158370] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [178.158470] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [178.158569] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [178.158668] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [178.158768] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [178.158868] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [178.158968] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [178.159069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [178.159169] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [178.159269] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:207:pipe C] fastset requirement not met, forcing full modeset
<7> [178.159485] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [178.159566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:89:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [178.159644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [178.159713] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [178.159782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [178.159851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [178.159919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [178.159987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [178.160083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:89:pipe A] data rate 1390840 num active planes 1
<7> [178.160197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [178.160310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [178.160437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [178.160549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [178.160659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [178.160771] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:89:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [178.160914] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [178.161027] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [178.161137] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [178.161246] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [178.161396] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:89:pipe A] allocated DPLL 0
<7> [178.161491] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:89:pipe A] reserving DPLL 0
<7> [178.161595] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:89:pipe A] enable: yes [modeset]
<7> [178.161706] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [178.161815] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [178.161924] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [178.162031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [178.162139] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [178.162246] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [178.162359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [178.162468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [178.162576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [178.162683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [178.162791] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [178.162898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [178.163006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [178.163114] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [178.163222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [178.163334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [178.163440] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [178.163547] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [178.163653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [178.163760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [178.163866] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [178.163973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [178.164080] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [178.164187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [178.164294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [178.164414] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [178.164525] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [178.164631] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [178.164739] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [178.164846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [178.164953] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [178.165059] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [178.165166] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [178.165272] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [178.165382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [178.165488] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [178.165594] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [178.165699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [178.165805] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [178.165911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [178.166018] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [178.166124] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [178.166231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [178.166340] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [178.166446] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [178.166552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [178.166659] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.166766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.166872] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.166978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [178.167086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [178.167192] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.167298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.167407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [178.167512] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [178.167619] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [178.167725] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:212] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [178.167836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [178.167943] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [178.168050] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [178.168156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [178.168262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [178.168377] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [178.168483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [178.168589] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:148:pipe B] enable: no [modeset]
<7> [178.168695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:92:plane 1B] fb: [NOFB], visible: no
<7> [178.168801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:102:plane 2B] fb: [NOFB], visible: no
<7> [178.168906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:112:plane 3B] fb: [NOFB], visible: no
<7> [178.169012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:122:plane 4B] fb: [NOFB], visible: no
<7> [178.169117] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:132:plane 5B] fb: [NOFB], visible: no
<7> [178.169223] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:142:cursor B] fb: [NOFB], visible: no
<7> [178.169335] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:207:pipe C] enable: no [modeset]
<7> [178.169441] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:151:plane 1C] fb: [NOFB], visible: no
<7> [178.169546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:161:plane 2C] fb: [NOFB], visible: no
<7> [178.169651] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:171:plane 3C] fb: [NOFB], visible: no
<7> [178.169757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:181:plane 4C] fb: [NOFB], visible: no
<7> [178.169862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:191:plane 5C] fb: [NOFB], visible: no
<7> [178.169968] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:201:cursor C] fb: [NOFB], visible: no
<7> [178.170218] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072)
<7> [178.171052] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [178.171196] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [178.171295] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [178.171417] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:210:DDI A/PHY A]
<7> [178.171506] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DDI TC1/PHY TC1]
<7> [178.171585] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:221:DP-MST A]
<7> [178.171664] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:222:DP-MST B]
<7> [178.171741] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:223:DP-MST C]
<7> [178.171819] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DDI TC2/PHY TC2]
<7> [178.171897] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:233:DP-MST A]
<7> [178.171974] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:234:DP-MST B]
<7> [178.172051] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:235:DP-MST C]
<7> [178.172129] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DDI TC3/PHY TC3]
<7> [178.172207] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:241:DP-MST A]
<7> [178.172284] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:242:DP-MST B]
<7> [178.172370] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:243:DP-MST C]
<7> [178.172449] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:220:DP-1]
<7> [178.172532] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:232:DP-2]
<7> [178.172613] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:240:DP-3]
<7> [178.172714] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [178.172879] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [178.172956] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [178.173067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [178.174364] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:89:pipe A]
<7> [178.174459] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [178.175682] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 turn panel power on
<7> [178.175770] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [178.175879] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [178.186013] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [178.186108] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 wait for panel power on
<7> [178.186218] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [178.222699] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [178.222982] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [178.223482] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:210:DDI A/PHY A]
<6> [178.246576] r8169 0000:7f:00.0 enp127s0: Link is Down
<7> [178.395368] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [178.395642] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 turning VDD on
<7> [178.395873] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:210:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [178.398446] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [178.399710] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [178.400376] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [178.401385] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [178.402564] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [178.403614] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Clock recovery OK
<7> [178.403817] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [178.405176] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [178.405404] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:211:eDP-1][ENCODER:210:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [178.406094] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [178.406488] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [178.406709] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [178.406984] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:211:eDP-1] set backlight PWM = 13892
<7> [178.423176] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [178.424703] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:211:eDP-1]
<7> [178.424968] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:89:pipe A]
<7> [178.427408] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:148:pipe B]
<7> [178.427670] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:207:pipe C]
<7> [178.429174] xe 0000:00:02.0: [drm:intel_opregion_resume [xe]] 4 outputs detected
<7> [178.431374] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:220:DP-1]
<7> [178.431694] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [178.431911] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:232:DP-2]
<7> [178.432160] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [178.432373] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:240:DP-3]
<7> [178.432617] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [178.436080] xe 0000:00:02.0: [drm:drm_client_dev_resume] fbdev: ret=0
<7> [178.436098] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC
<7> [178.436399] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D
<7> [178.436669] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C
<7> [178.436915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [178.437151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [178.437379] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [178.437604] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [178.437817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [178.438254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [178.438946] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010
<7> [178.451125] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [178.451545] PM: resume of devices complete after 385.850 msecs
<7> [178.452098] GFP mask restored
<6> [178.463452] OOM killer enabled.
<6> [178.463463] Restarting tasks: Starting
<6> [178.464761] mei_gsc_proxy 0000:00:16.0-0f73db04-97ab-4125-b893-e904ad0d5464: bound 0000:00:02.0 (ops xe_gsc_proxy_component_ops [xe])
<6> [178.469290] Restarting tasks: Done
<6> [178.479442] efivarfs: resyncing variable state
<6> [178.497194] efivarfs: finished resyncing variable state
<5> [178.497294] random: crng reseeded on system resumption
<6> [178.515989] PM: suspend exit
<6> [178.531970] [IGT] xe_pm: finished subtest s2idle-basic-exec, SUCCESS
<7> [178.537966] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [178.538251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [178.540700] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [178.541046] [IGT] xe_pm: exiting, ret=0
<6> [178.557067] Console: switching to colour frame buffer device 180x56
<7> [178.590326] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [178.590678] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [178.590812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
|