<5>[ 0.000000] Linux version 6.18.0-rc2-lgci-xe-xe-3969-71929a54e8bb5da29+ (builder@lgci) (gcc (Ubuntu 13.3.0-6ubuntu2~24.04) 13.3.0, GNU ld (GNU Binutils for Ubuntu) 2.42) #1 SMP PREEMPT_DYNAMIC Wed Oct 22 20:20:13 UTC 2025 <6>[ 0.000000] Command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <6>[ 0.000000] KERNEL supported cpus: <6>[ 0.000000] Intel GenuineIntel <6>[ 0.000000] AMD AuthenticAMD <6>[ 0.000000] Hygon HygonGenuine <6>[ 0.000000] Centaur CentaurHauls <6>[ 0.000000] zhaoxin Shanghai <6>[ 0.000000] x86/tme: not enabled by BIOS <6>[ 0.000000] x86/split lock detection: #AC: crashing the kernel on kernel split_locks and warning on user-space split_locks <6>[ 0.000000] BIOS-provided physical RAM map: <6>[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x00000000000fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006cac0fff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000006cac1000-0x000000006fe67fff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x000000006fe68000-0x000000006ff4ffff] ACPI NVS <6>[ 0.000000] BIOS-e820: [mem 0x000000006ff50000-0x000000006fffefff] ACPI data <6>[ 0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable <6>[ 0.000000] BIOS-e820: [mem 0x0000000070000000-0x00000000807fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000c0000000-0x00000000cfffffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fed7ffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000ff200000-0x00000001044fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000104500000-0x000000087f7fffff] usable <6>[ 0.000000] NX (Execute Disable) protection: active <6>[ 0.000000] APIC: Static calls initialized <6>[ 0.000000] efi: EFI v2.7 by Intel <6>[ 0.000000] efi: ACPI=0x6fffe000 ACPI 2.0=0x6fffe014 SMBIOS=0x6cbc7000 MEMATTR=0x68f6c018 ESRT=0x68f7da98 MOKvar=0x6cd0c000 <6>[ 0.000000] efi: Remove mem277: MMIO range=[0xc0000000-0xcfffffff] (256MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xc0000000-0xcfffffff] reserved <6>[ 0.000000] efi: Remove mem279: MMIO range=[0xff200000-0xffffffff] (14MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xff200000-0xffffffff] reserved <6>[ 0.000000] SMBIOS 3.8 present. <6>[ 0.000000] DMI: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D96.2504232223 04/23/2025 <6>[ 0.000000] DMI: Memory slots populated: 8/8 <6>[ 0.000000] tsc: Detected 3100.000 MHz processor <6>[ 0.000000] tsc: Detected 3110.400 MHz TSC <7>[ 0.000009] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved <7>[ 0.000010] e820: remove [mem 0x000a0000-0x000fffff] usable <6>[ 0.000014] last_pfn = 0x87f800 max_arch_pfn = 0x400000000 <6>[ 0.000017] MTRR map: 6 entries (3 fixed + 3 variable; max 23), built from 10 variable MTRRs <6>[ 0.000019] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT <6>[ 0.000388] x2apic: enabled by BIOS, switching to x2apic ops <6>[ 0.000389] last_pfn = 0x70000 max_arch_pfn = 0x400000000 <6>[ 0.004900] esrt: Reserving ESRT space from 0x0000000068f7da98 to 0x0000000068f7dbe8. <7>[ 0.004908] e820: update [mem 0x68f7d000-0x68f7dfff] usable ==> reserved <6>[ 0.004926] Using GB pages for direct mapping <6>[ 0.005578] printk: log buffer data + meta data: 1048576 + 3670016 = 4718592 bytes <6>[ 0.005579] printk: early log buf free: 258816(98%) <6>[ 0.005579] Secure boot disabled <6>[ 0.005581] ACPI: Early table checksum verification disabled <6>[ 0.005584] ACPI: RSDP 0x000000006FFFE014 000024 (v02 INTEL ) <6>[ 0.005587] ACPI: XSDT 0x000000006FF70228 00019C (v01 INTEL LNL 00000002 01000013) <6>[ 0.005590] ACPI: FACP 0x000000006FFAA000 000114 (v06 INTEL LNL 00000002 01000013) <6>[ 0.005593] ACPI: DSDT 0x000000006FFB6000 025547 (v02 INTEL LNL 00000002 01000013) <6>[ 0.005595] ACPI: FACS 0x000000006FEF1000 000040 <6>[ 0.005596] ACPI: SSDT 0x000000006FFFC000 000388 (v02 PmaxDv Pmax_Dev 00000001 INTL 20210930) <6>[ 0.005598] ACPI: SSDT 0x000000006FFFB000 0006AA (v02 PmRef Cpu0Ist 00003000 INTL 20210930) <6>[ 0.005599] ACPI: SSDT 0x000000006FFFA000 0005FB (v02 PmRef Cpu0Hwp 00003000 INTL 20210930) <6>[ 0.005600] ACPI: SSDT 0x000000006FFF9000 0001AB (v02 PmRef Cpu0Psd 00003000 INTL 20210930) <6>[ 0.005602] ACPI: SSDT 0x000000006FFF8000 000394 (v02 PmRef Cpu0Cst 00003001 INTL 20210930) <6>[ 0.005603] ACPI: SSDT 0x000000006FFF6000 001BAF (v02 PmRef ApIst 00003000 INTL 20210930) <6>[ 0.005604] ACPI: SSDT 0x000000006FFF4000 001620 (v02 PmRef ApHwp 00003000 INTL 20210930) <6>[ 0.005606] ACPI: SSDT 0x000000006FFF2000 001349 (v02 PmRef ApPsd 00003000 INTL 20210930) <6>[ 0.005607] ACPI: SSDT 0x000000006FFF1000 000FBB (v02 PmRef ApCst 00003000 INTL 20210930) <6>[ 0.005608] ACPI: SSDT 0x000000006FFED000 003BD7 (v02 CpuRef CpuSsdt 00003000 INTL 20210930) <6>[ 0.005610] ACPI: DTPR 0x000000006FFEC000 000090 (v01 00000000 00000000) <6>[ 0.005611] ACPI: SSDT 0x000000006FFEB000 000FE2 (v02 INTEL PDatTabl 00001000 INTL 20210930) <6>[ 0.005613] ACPI: SSDT 0x000000006FFE8000 002450 (v02 INTEL IgfxSsdt 00003000 INTL 20210930) <6>[ 0.005614] ACPI: SSDT 0x000000006FFE7000 0000A5 (v02 INTEL TseSsdt 00001000 INTL 20210930) <6>[ 0.005615] ACPI: SSDT 0x000000006FFDD000 009176 (v02 INTEL TcssSsdt 00001000 INTL 20210930) <6>[ 0.005616] ACPI: SSDT 0x000000006FFDC000 0000E0 (v02 INTEL IpuSsdt 00001000 INTL 20210930) <6>[ 0.005618] ACPI: SSDT 0x000000006FFB1000 004AC3 (v02 INTEL LnlMRvp1 00001000 INTL 20210930) <6>[ 0.005619] ACPI: SSDT 0x000000006FFAF000 00140F (v02 INTEL I2Pm_Rvp 00001000 INTL 20210930) <6>[ 0.005620] ACPI: SSDT 0x000000006FFAB000 003956 (v02 INTEL Ther_Rvp 00001000 INTL 20210930) <6>[ 0.005622] ACPI: HPET 0x000000006FFA9000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005623] ACPI: WSMT 0x000000006FFFD000 000028 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005624] ACPI: APIC 0x000000006FFA7000 0000D8 (v06 INTEL LNL 00000000 01000013) <6>[ 0.005625] ACPI: MCFG 0x000000006FFA6000 00003C (v01 INTEL LNL 00000002 01000013) <6>[ 0.005627] ACPI: SSDT 0x000000006FFA5000 0006E3 (v02 INTEL PepoSsdt 00001000 INTL 20210930) <6>[ 0.005628] ACPI: SSDT 0x000000006FF9F000 005321 (v02 DptfTb DptfTabl 00001000 INTL 20210930) <6>[ 0.005629] ACPI: SSDT 0x000000006FF94000 00A46A (v02 MiCaTb MiCaTabl 00001000 INTL 20210930) <6>[ 0.005631] ACPI: SSDT 0x000000006FF86000 00D816 (v02 INTEL Cnv_Ssdt 00001000 INTL 20210930) <6>[ 0.005632] ACPI: LPIT 0x000000006FF85000 0000CC (v01 INTEL LNL 00000002 01000013) <6>[ 0.005633] ACPI: SSDT 0x000000006FF84000 000D5C (v02 INTEL PtidDevc 00001000 INTL 20210930) <6>[ 0.005635] ACPI: SSDT 0x000000006FF83000 0001F0 (v02 INTEL TbtTypeC 00000000 INTL 20210930) <6>[ 0.005636] ACPI: DBGP 0x000000006FF82000 000034 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005637] ACPI: DBG2 0x000000006FF81000 000054 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005638] ACPI: NHLT 0x000000006FF80000 0002E3 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005640] ACPI: SSDT 0x000000006FF7E000 00115C (v02 INTEL UsbCTabl 00001000 INTL 20210930) <6>[ 0.005641] ACPI: SSDT 0x000000006FF77000 00653B (v02 INTEL EcSsdt 00000000 INTL 20210930) <6>[ 0.005642] ACPI: ECDT 0x000000006FF76000 000069 (v01 LNL 00000002 01000013) <6>[ 0.005644] ACPI: DMAR 0x000000006FF75000 0000D8 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005645] ACPI: FPDT 0x000000006FF74000 000044 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005646] ACPI: SSDT 0x000000006FF73000 00086D (v02 INTEL xh_lnl_m 00000000 INTL 20210930) <6>[ 0.005648] ACPI: SSDT 0x000000006FF71000 0013DB (v02 SocGpe SocGpe 00003000 INTL 20210930) <6>[ 0.005649] ACPI: SSDT 0x000000006FF6D000 002463 (v02 SocCmn SocCmn 00003000 INTL 20210930) <6>[ 0.005650] ACPI: SDEV 0x000000006FFA8000 000046 (v01 00000000 00000000) <6>[ 0.005652] ACPI: SSDT 0x000000006FF62000 00A4FA (v02 INTEL St09Ssdt 00001000 INTL 20210930) <6>[ 0.005653] ACPI: ASF! 0x000000006FF61000 000074 (v32 INTEL LNL 00000002 01000013) <6>[ 0.005654] ACPI: PHAT 0x000000006FF60000 0007C0 (v01 INTEL LNL 00000005 MSFT 0100000D) <6>[ 0.005656] ACPI: BGRT 0x000000006FF5F000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005657] ACPI: Reserving FACP table memory at [mem 0x6ffaa000-0x6ffaa113] <6>[ 0.005658] ACPI: Reserving DSDT table memory at [mem 0x6ffb6000-0x6ffdb546] <6>[ 0.005658] ACPI: Reserving FACS table memory at [mem 0x6fef1000-0x6fef103f] <6>[ 0.005658] ACPI: Reserving SSDT table memory at [mem 0x6fffc000-0x6fffc387] <6>[ 0.005659] ACPI: Reserving SSDT table memory at [mem 0x6fffb000-0x6fffb6a9] <6>[ 0.005659] ACPI: Reserving SSDT table memory at [mem 0x6fffa000-0x6fffa5fa] <6>[ 0.005659] ACPI: Reserving SSDT table memory at [mem 0x6fff9000-0x6fff91aa] <6>[ 0.005659] ACPI: Reserving SSDT table memory at [mem 0x6fff8000-0x6fff8393] <6>[ 0.005660] ACPI: Reserving SSDT table memory at [mem 0x6fff6000-0x6fff7bae] <6>[ 0.005660] ACPI: Reserving SSDT table memory at [mem 0x6fff4000-0x6fff561f] <6>[ 0.005660] ACPI: Reserving SSDT table memory at [mem 0x6fff2000-0x6fff3348] <6>[ 0.005661] ACPI: Reserving SSDT table memory at [mem 0x6fff1000-0x6fff1fba] <6>[ 0.005661] ACPI: Reserving SSDT table memory at [mem 0x6ffed000-0x6fff0bd6] <6>[ 0.005661] ACPI: Reserving DTPR table memory at [mem 0x6ffec000-0x6ffec08f] <6>[ 0.005661] ACPI: Reserving SSDT table memory at [mem 0x6ffeb000-0x6ffebfe1] <6>[ 0.005662] ACPI: Reserving SSDT table memory at [mem 0x6ffe8000-0x6ffea44f] <6>[ 0.005662] ACPI: Reserving SSDT table memory at [mem 0x6ffe7000-0x6ffe70a4] <6>[ 0.005662] ACPI: Reserving SSDT table memory at [mem 0x6ffdd000-0x6ffe6175] <6>[ 0.005662] ACPI: Reserving SSDT table memory at [mem 0x6ffdc000-0x6ffdc0df] <6>[ 0.005663] ACPI: Reserving SSDT table memory at [mem 0x6ffb1000-0x6ffb5ac2] <6>[ 0.005663] ACPI: Reserving SSDT table memory at [mem 0x6ffaf000-0x6ffb040e] <6>[ 0.005663] ACPI: Reserving SSDT table memory at [mem 0x6ffab000-0x6ffae955] <6>[ 0.005664] ACPI: Reserving HPET table memory at [mem 0x6ffa9000-0x6ffa9037] <6>[ 0.005664] ACPI: Reserving WSMT table memory at [mem 0x6fffd000-0x6fffd027] <6>[ 0.005664] ACPI: Reserving APIC table memory at [mem 0x6ffa7000-0x6ffa70d7] <6>[ 0.005664] ACPI: Reserving MCFG table memory at [mem 0x6ffa6000-0x6ffa603b] <6>[ 0.005665] ACPI: Reserving SSDT table memory at [mem 0x6ffa5000-0x6ffa56e2] <6>[ 0.005665] ACPI: Reserving SSDT table memory at [mem 0x6ff9f000-0x6ffa4320] <6>[ 0.005665] ACPI: Reserving SSDT table memory at [mem 0x6ff94000-0x6ff9e469] <6>[ 0.005666] ACPI: Reserving SSDT table memory at [mem 0x6ff86000-0x6ff93815] <6>[ 0.005666] ACPI: Reserving LPIT table memory at [mem 0x6ff85000-0x6ff850cb] <6>[ 0.005666] ACPI: Reserving SSDT table memory at [mem 0x6ff84000-0x6ff84d5b] <6>[ 0.005666] ACPI: Reserving SSDT table memory at [mem 0x6ff83000-0x6ff831ef] <6>[ 0.005667] ACPI: Reserving DBGP table memory at [mem 0x6ff82000-0x6ff82033] <6>[ 0.005667] ACPI: Reserving DBG2 table memory at [mem 0x6ff81000-0x6ff81053] <6>[ 0.005667] ACPI: Reserving NHLT table memory at [mem 0x6ff80000-0x6ff802e2] <6>[ 0.005668] ACPI: Reserving SSDT table memory at [mem 0x6ff7e000-0x6ff7f15b] <6>[ 0.005668] ACPI: Reserving SSDT table memory at [mem 0x6ff77000-0x6ff7d53a] <6>[ 0.005668] ACPI: Reserving ECDT table memory at [mem 0x6ff76000-0x6ff76068] <6>[ 0.005668] ACPI: Reserving DMAR table memory at [mem 0x6ff75000-0x6ff750d7] <6>[ 0.005669] ACPI: Reserving FPDT table memory at [mem 0x6ff74000-0x6ff74043] <6>[ 0.005669] ACPI: Reserving SSDT table memory at [mem 0x6ff73000-0x6ff7386c] <6>[ 0.005669] ACPI: Reserving SSDT table memory at [mem 0x6ff71000-0x6ff723da] <6>[ 0.005670] ACPI: Reserving SSDT table memory at [mem 0x6ff6d000-0x6ff6f462] <6>[ 0.005670] ACPI: Reserving SDEV table memory at [mem 0x6ffa8000-0x6ffa8045] <6>[ 0.005670] ACPI: Reserving SSDT table memory at [mem 0x6ff62000-0x6ff6c4f9] <6>[ 0.005671] ACPI: Reserving ASF! table memory at [mem 0x6ff61000-0x6ff61073] <6>[ 0.005671] ACPI: Reserving PHAT table memory at [mem 0x6ff60000-0x6ff607bf] <6>[ 0.005671] ACPI: Reserving BGRT table memory at [mem 0x6ff5f000-0x6ff5f037] <6>[ 0.005746] APIC: Switched APIC routing to: cluster x2apic <6>[ 0.005948] No NUMA configuration found <6>[ 0.005948] Faking a node at [mem 0x0000000000000000-0x000000087f7fffff] <6>[ 0.005953] NODE_DATA(0) allocated [mem 0x87f352e40-0x87f37dfff] <6>[ 0.006069] Zone ranges: <6>[ 0.006069] DMA [mem 0x0000000000001000-0x0000000000ffffff] <6>[ 0.006070] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] <6>[ 0.006071] Normal [mem 0x0000000100000000-0x000000087f7fffff] <6>[ 0.006072] Device empty <6>[ 0.006072] Movable zone start for each node <6>[ 0.006073] Early memory node ranges <6>[ 0.006073] node 0: [mem 0x0000000000001000-0x000000000009efff] <6>[ 0.006074] node 0: [mem 0x0000000000100000-0x000000006cac0fff] <6>[ 0.006075] node 0: [mem 0x000000006ffff000-0x000000006fffffff] <6>[ 0.006075] node 0: [mem 0x0000000104500000-0x000000087f7fffff] <6>[ 0.006076] Initmem setup node 0 [mem 0x0000000000001000-0x000000087f7fffff] <6>[ 0.006081] On node 0, zone DMA: 1 pages in unavailable ranges <6>[ 0.006095] On node 0, zone DMA: 97 pages in unavailable ranges <6>[ 0.007719] On node 0, zone DMA32: 13630 pages in unavailable ranges <6>[ 0.035698] On node 0, zone Normal: 17664 pages in unavailable ranges <6>[ 0.035705] On node 0, zone Normal: 2048 pages in unavailable ranges <6>[ 0.036166] ACPI: PM-Timer IO Port: 0x1808 <6>[ 0.036173] ACPI: X2APIC_NMI (uid[0xffffffff] high level lint[0x1]) <6>[ 0.036225] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 <6>[ 0.036226] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <6>[ 0.036228] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <6>[ 0.036230] ACPI: Using ACPI (MADT) for SMP configuration information <6>[ 0.036231] ACPI: HPET id: 0x8086a701 base: 0xfed00000 <7>[ 0.036242] e820: update [mem 0x68f28000-0x68f42fff] usable ==> reserved <6>[ 0.036248] TSC deadline timer available <6>[ 0.036250] CPU topo: Max. logical packages: 1 <6>[ 0.036250] CPU topo: Max. logical dies: 1 <6>[ 0.036251] CPU topo: Max. dies per package: 1 <6>[ 0.036252] CPU topo: Max. threads per core: 1 <6>[ 0.036252] CPU topo: Num. cores per package: 8 <6>[ 0.036253] CPU topo: Num. threads per package: 8 <6>[ 0.036253] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs <6>[ 0.036265] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] <6>[ 0.036266] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] <6>[ 0.036267] PM: hibernation: Registered nosave memory: [mem 0x68f28000-0x68f42fff] <6>[ 0.036268] PM: hibernation: Registered nosave memory: [mem 0x68f7d000-0x68f7dfff] <6>[ 0.036269] PM: hibernation: Registered nosave memory: [mem 0x6cac1000-0x6fffefff] <6>[ 0.036270] PM: hibernation: Registered nosave memory: [mem 0x70000000-0x1044fffff] <6>[ 0.036271] [mem 0x80800000-0xfed1ffff] available for PCI devices <6>[ 0.036272] Booting paravirtualized kernel on bare hardware <6>[ 0.036274] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns <6>[ 0.036282] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1 <6>[ 0.036606] percpu: Embedded 86 pages/cpu s229376 r8192 d114688 u524288 <7>[ 0.036610] pcpu-alloc: s229376 r8192 d114688 u524288 alloc=1*2097152 <7>[ 0.036611] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 <5>[ 0.036624] Kernel command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <7>[ 0.036715] blacklisting initcall simpledrm_platform_driver_init <5>[ 0.036732] random: crng init done <6>[ 0.038592] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) <6>[ 0.039514] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) <6>[ 0.039573] software IO TLB: area num 8. <6>[ 0.046939] Fallback order for Node 0: 0 <6>[ 0.046942] Built 1 zonelists, mobility grouping on. Total pages: 8289632 <6>[ 0.046943] Policy zone: Normal <6>[ 0.046953] mem auto-init: stack:off, heap alloc:on, heap free:off <6>[ 0.046954] stackdepot: allocating hash table via alloc_large_system_hash <6>[ 0.046957] stackdepot hash table entries: 1048576 (order: 12, 16777216 bytes, linear) <6>[ 0.047883] stackdepot: allocating space for 8192 stack pools via memblock <4>[ 0.079719] ********************************************************** <4>[ 0.079720] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.079720] ** ** <4>[ 0.079720] ** This system shows unhashed kernel memory addresses ** <4>[ 0.079721] ** via the console, logs, and other interfaces. This ** <4>[ 0.079721] ** might reduce the security of your system. ** <4>[ 0.079721] ** ** <4>[ 0.079721] ** If you see this message and you are not debugging ** <4>[ 0.079721] ** the kernel, report this immediately to your system ** <4>[ 0.079722] ** administrator! ** <4>[ 0.079722] ** ** <4>[ 0.079722] ** Use hash_pointers=always to force this mode off ** <4>[ 0.079722] ** ** <4>[ 0.079722] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.079722] ********************************************************** <6>[ 0.080829] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 <6>[ 0.089111] ftrace: allocating 60594 entries in 240 pages <6>[ 0.089113] ftrace: allocated 240 pages with 4 groups <6>[ 0.090550] Dynamic Preempt: voluntary <6>[ 0.091083] Running RCU self tests <6>[ 0.091084] Running RCU synchronous self tests <6>[ 0.091084] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.091085] rcu: RCU lockdep checking is enabled. <6>[ 0.091085] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8. <6>[ 0.091086] Trampoline variant of Tasks RCU enabled. <6>[ 0.091086] Rude variant of Tasks RCU enabled. <6>[ 0.091086] Tracing variant of Tasks RCU enabled. <6>[ 0.091087] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. <6>[ 0.091087] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 <6>[ 0.091155] Running RCU synchronous self tests <6>[ 0.091160] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.091163] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.091165] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.102092] NR_IRQS: 524544, nr_irqs: 2048, preallocated irqs: 16 <6>[ 0.102570] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.102984] Console: colour dummy device 80x25 <6>[ 0.102993] printk: legacy console [tty0] enabled <6>[ 0.104159] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <6>[ 0.104166] ... MAX_LOCKDEP_SUBCLASSES: 8 <6>[ 0.104170] ... MAX_LOCK_DEPTH: 48 <6>[ 0.104173] ... MAX_LOCKDEP_KEYS: 8192 <6>[ 0.104177] ... CLASSHASH_SIZE: 4096 <6>[ 0.104180] ... MAX_LOCKDEP_ENTRIES: 524288 <6>[ 0.104184] ... MAX_LOCKDEP_CHAINS: 524288 <6>[ 0.104187] ... CHAINHASH_SIZE: 262144 <6>[ 0.104191] memory used by lock dependency info: 54145 kB <6>[ 0.104195] memory used for stack traces: 4224 kB <6>[ 0.104199] per task-struct memory footprint: 1920 bytes <6>[ 0.104248] ACPI: Core revision 20250807 <6>[ 0.105154] hpet: HPET dysfunctional in PC10. Force disabled. <6>[ 0.105218] APIC: Switch to symmetric I/O mode setup <6>[ 0.105225] DMAR: Host address width 38 <6>[ 0.105228] DMAR: DRHD base: 0x000000fc800000 flags: 0x0 <6>[ 0.105260] DMAR: dmar0: reg_base_addr fc800000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.105292] DMAR: DRHD base: 0x000000fc810000 flags: 0x0 <6>[ 0.105314] DMAR: dmar1: reg_base_addr fc810000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.105339] DMAR: DRHD base: 0x000000fc820000 flags: 0x1 <6>[ 0.105360] DMAR: dmar2: reg_base_addr fc820000 ver 7:1 cap e9de008cee690402 ecap 1ac89800f0efda <6>[ 0.105393] DMAR: SATC flags: 0x1 <6>[ 0.105403] DMAR-IR: IOAPIC id 2 under DRHD base 0xfc820000 IOMMU 2 <6>[ 0.105408] DMAR-IR: HPET id 0 under DRHD base 0xfc820000 <6>[ 0.105412] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping. <6>[ 0.107465] DMAR-IR: Enabled IRQ remapping in x2apic mode <6>[ 0.112639] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 0.112657] Calibrating delay loop (skipped), value calculated using timer frequency.. 6220.80 BogoMIPS (lpj=3110400) <6>[ 0.112733] CPU0: Thermal monitoring enabled (TM1) <6>[ 0.112739] x86/cpu: User Mode Instruction Prevention (UMIP) activated <6>[ 0.112918] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 <6>[ 0.112923] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 <6>[ 0.112932] mitigations: Enabled attack vectors: user_kernel, user_user, guest_host, guest_guest, SMT mitigations: auto <6>[ 0.112943] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl <6>[ 0.112950] Spectre V2 : Mitigation: Enhanced / Automatic IBRS <6>[ 0.112955] VMSCAPE: Mitigation: IBPB before exit to userspace <6>[ 0.112960] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization <6>[ 0.112968] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier <6>[ 0.112985] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' <6>[ 0.112992] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' <6>[ 0.112998] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' <6>[ 0.113003] x86/fpu: Supporting XSAVE feature 0x200: 'Protection Keys User registers' <6>[ 0.113010] x86/fpu: Supporting XSAVE feature 0x800: 'Control-flow User registers' <6>[ 0.113016] x86/fpu: Supporting XSAVE feature 0x1000: 'Control-flow Kernel registers (KVM only)' <6>[ 0.113023] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 <6>[ 0.113029] x86/fpu: xstate_offset[9]: 832, xstate_sizes[9]: 8 <6>[ 0.113034] x86/fpu: xstate_offset[11]: 840, xstate_sizes[11]: 16 <6>[ 0.113040] x86/fpu: xstate_offset[12]: 856, xstate_sizes[12]: 24 <6>[ 0.113046] x86/fpu: Enabled xstate features 0x1a07, context size is 880 bytes, using 'compacted' format. <6>[ 0.113651] Freeing SMP alternatives memory: 56K <6>[ 0.113651] pid_max: default: 32768 minimum: 301 <6>[ 0.113651] LSM: initializing lsm=capability,landlock,yama,apparmor,ima,evm <6>[ 0.113651] landlock: Up and running. <6>[ 0.113651] Yama: becoming mindful. <6>[ 0.113651] AppArmor: AppArmor initialized <6>[ 0.113651] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.113651] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.113651] Running RCU synchronous self tests <6>[ 0.113651] Running RCU synchronous self tests <6>[ 0.113651] smpboot: CPU0: Intel(R) Core(TM) Ultra 5 238V (family: 0x6, model: 0xbd, stepping: 0x1) <6>[ 0.113651] Performance Events: XSAVE Architectural LBR, PEBS fmt6+-baseline, AnyThread deprecated, Lunarlake Hybrid events, 32-deep LBR, full-width counters, Intel PMU driver. <6>[ 0.113651] core: cpu_core PMU driver: <6>[ 0.113651] ... version: 6 <6>[ 0.113651] ... bit width: 48 <6>[ 0.113651] ... generic counters: 10 <6>[ 0.113651] ... generic bitmap: 00000000000003ff <6>[ 0.113651] ... fixed-purpose counters: 4 <6>[ 0.113651] ... fixed-purpose bitmap: 000000000000000f <6>[ 0.113651] ... value mask: 0000ffffffffffff <6>[ 0.113651] ... max period: 00007fffffffffff <6>[ 0.113651] ... global_ctrl mask: 0001000f000003ff <6>[ 0.113720] signal: max sigframe size: 3632 <6>[ 0.113744] Estimated ratio of average max frequency by base frequency (times 1024): 1189 <6>[ 0.113847] rcu: Hierarchical SRCU implementation. <6>[ 0.113851] rcu: Max phase no-delay instances is 400. <6>[ 0.113999] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.115854] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. <6>[ 0.116124] smp: Bringing up secondary CPUs ... <6>[ 0.116470] smpboot: x86: Booting SMP configuration: <6>[ 0.116477] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 <6>[ 0.010894] core: cpu_atom PMU driver: <6>[ 0.010894] ... version: 6 <6>[ 0.010894] ... bit width: 48 <6>[ 0.010894] ... generic counters: 8 <6>[ 0.010894] ... generic bitmap: 00000000000000ff <6>[ 0.010894] ... fixed-purpose counters: 6 <6>[ 0.010894] ... fixed-purpose bitmap: 0000000000000077 <6>[ 0.010894] ... value mask: 0000ffffffffffff <6>[ 0.010894] ... max period: 00007fffffffffff <6>[ 0.010894] ... global_ctrl mask: 00000077000000ff <6>[ 0.122776] smp: Brought up 1 node, 8 CPUs <6>[ 0.123221] smpboot: Total of 8 processors activated (49766.40 BogoMIPS) <6>[ 0.124763] Memory: 32358224K/33158528K available (25413K kernel code, 5651K rwdata, 9540K rodata, 5704K init, 68232K bss, 777188K reserved, 0K cma-reserved) <6>[ 0.125221] devtmpfs: initialized <6>[ 0.125849] x86/mm: Memory block size: 128MB <6>[ 0.147703] ACPI: PM: Registering ACPI NVS region [mem 0x6fe68000-0x6ff4ffff] (950272 bytes) <6>[ 0.148222] Running RCU synchronous self tests <6>[ 0.148233] Running RCU synchronous self tests <6>[ 0.148825] Running RCU Tasks wait API self tests <6>[ 0.148825] Running RCU Tasks Rude wait API self tests <6>[ 0.148825] Running RCU Tasks Trace wait API self tests <6>[ 0.162717] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.163126] posixtimers hash table entries: 4096 (order: 6, 294912 bytes, linear) <6>[ 0.164128] futex hash table entries: 2048 (262144 bytes on 1 NUMA nodes, total 256 KiB, linear). <6>[ 0.167206] pinctrl core: initialized pinctrl subsystem <6>[ 0.169405] PM: RTC time: 23:39:25, date: 2025-10-22 <6>[ 0.170184] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.171158] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.171455] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.171733] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.171789] audit: initializing netlink subsys (disabled) <5>[ 0.171953] audit: type=2000 audit(1761176365.059:1): state=initialized audit_enabled=0 res=1 <6>[ 0.172928] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.172930] thermal_sys: Registered thermal governor 'bang_bang' <6>[ 0.172936] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.172941] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.172946] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.172984] cpuidle: using governor ladder <6>[ 0.172984] cpuidle: using governor menu <6>[ 0.172984] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 <6>[ 0.173812] PCI: ECAM [mem 0xc0000000-0xcfffffff] (base 0xc0000000) for domain 0000 [bus 00-ff] <6>[ 0.173839] PCI: Using configuration type 1 for base access <6>[ 0.173957] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. <6>[ 0.175715] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.175715] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.175720] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.175725] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.179902] raid6: skipped pq benchmark and selected avx2x4 <6>[ 0.179909] raid6: using avx2x2 recovery algorithm <6>[ 0.180485] fbcon: Taking over console <6>[ 0.180708] ACPI: Added _OSI(Module Device) <6>[ 0.180716] ACPI: Added _OSI(Processor Device) <6>[ 0.180723] ACPI: Added _OSI(Processor Aggregator Device) <6>[ 0.181703] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.693584] ACPI: 31 ACPI AML tables successfully acquired and loaded <6>[ 0.719515] ACPI: EC: EC started <6>[ 0.719544] ACPI: EC: interrupt blocked <6>[ 0.725651] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 0.725651] ACPI: EC: Boot ECDT EC used to handle transactions <6>[ 0.790682] Callback from call_rcu_tasks() invoked. <6>[ 1.029201] ACPI: USB4 _OSC: OS supports USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.029279] ACPI: USB4 _OSC: OS controls USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.097682] ACPI: Interpreter enabled <6>[ 1.097887] ACPI: PM: (supports S0 S4 S5) <6>[ 1.097897] ACPI: Using IOAPIC for interrupt routing <6>[ 1.110917] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug <6>[ 1.110934] PCI: Ignoring E820 reservations for host bridge windows <6>[ 1.162550] ACPI: Enabled 10 GPEs in block 00 to 7F <6>[ 1.162619] ACPI: Enabled 13 GPEs in block 80 to DF <6>[ 1.228796] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.BTRT: New power resource <6>[ 1.229567] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.DBTR: New power resource <6>[ 1.238129] ACPI: \_SB_.PC00.PAUD: New power resource <6>[ 1.640201] ACPI: \_SB_.PC00.CNVW.WRST: New power resource <6>[ 1.653671] ACPI: \_SB_.PC00.RP02.PXP_: New power resource <6>[ 1.791173] ACPI: \_SB_.PC00.RP03.PXSX.WRST: New power resource <6>[ 1.792806] ACPI: \_SB_.PC00.RP04.PXP_: New power resource <6>[ 1.801613] ACPI: \_SB_.PC00.RP05.PXP_: New power resource <6>[ 1.811335] ACPI: \_SB_.PC00.TBT0: New power resource <6>[ 1.811602] ACPI: \_SB_.PC00.TBT1: New power resource <6>[ 1.812240] ACPI: \_SB_.PC00.D3C_: New power resource <6>[ 2.182838] ACPI: \_TZ_.FN00: New power resource <6>[ 2.183380] ACPI: \_TZ_.FN01: New power resource <6>[ 2.184299] ACPI: \_TZ_.FN02: New power resource <6>[ 2.184821] ACPI: \_TZ_.FN03: New power resource <6>[ 2.185340] ACPI: \_TZ_.FN04: New power resource <6>[ 2.186707] ACPI: \PIN_: New power resource <6>[ 2.190388] ACPI: PCI Root Bridge [PC00] (domain 0000 [bus 00-fe]) <6>[ 2.190403] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3] <6>[ 2.193940] acpi PNP0A08:00: _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability LTR DPC] <6>[ 2.219736] PCI host bridge to bus 0000:00 <6>[ 2.219775] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] <6>[ 2.219785] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] <6>[ 2.219792] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] <6>[ 2.219799] pci_bus 0000:00: root bus resource [mem 0x80800000-0xbfffffff window] <6>[ 2.219806] pci_bus 0000:00: root bus resource [mem 0x2000000000-0x3fbfffffff window] <6>[ 2.219815] pci_bus 0000:00: root bus resource [bus 00-fe] <6>[ 2.222861] pci 0000:00:00.0: [8086:6400] type 00 class 0x060000 conventional PCI endpoint <6>[ 2.223519] pci 0000:00:02.0: [8086:64a0] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint <6>[ 2.223610] pci 0000:00:02.0: BAR 0 [mem 0x3814000000-0x3814ffffff 64bit pref] <6>[ 2.223618] pci 0000:00:02.0: BAR 2 [mem 0x2000000000-0x200fffffff 64bit pref] <6>[ 2.223627] pci 0000:00:02.0: ROM [mem 0xffe00000-0xffffffff pref] <6>[ 2.223708] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] <6>[ 2.225173] pci 0000:00:04.0: [8086:641d] type 00 class 0x118000 conventional PCI endpoint <6>[ 2.225203] pci 0000:00:04.0: BAR 0 [mem 0x3815300000-0x381531ffff 64bit] <6>[ 2.226418] pci 0000:00:05.0: [8086:645d] type 00 class 0x048000 PCIe Root Complex Integrated Endpoint <6>[ 2.226448] pci 0000:00:05.0: BAR 0 [mem 0x3812000000-0x3813ffffff 64bit] <6>[ 2.226455] pci 0000:00:05.0: BAR 4 [mem 0x3815373000-0x3815373fff 64bit] <6>[ 2.227344] pci 0000:00:07.0: [8086:a84e] type 01 class 0x060400 PCIe Root Port <6>[ 2.227389] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 2.227401] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 2.227419] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 2.227534] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold <6>[ 2.227607] pci 0000:00:07.0: PTM enabled (root), 4ns granularity <6>[ 2.232210] pci 0000:00:07.1: [8086:a84f] type 01 class 0x060400 PCIe Root Port <6>[ 2.232256] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 2.232268] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 2.232286] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 2.232403] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold <6>[ 2.232469] pci 0000:00:07.1: PTM enabled (root), 4ns granularity <6>[ 2.236695] pci 0000:00:07.2: [8086:a860] type 01 class 0x060400 PCIe Root Port <6>[ 2.236738] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 2.236750] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 2.236768] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 2.236885] pci 0000:00:07.2: PME# supported from D0 D3hot D3cold <6>[ 2.236950] pci 0000:00:07.2: PTM enabled (root), 4ns granularity <6>[ 2.241390] pci 0000:00:0a.0: [8086:647d] type 00 class 0x118000 PCIe Root Complex Integrated Endpoint <6>[ 2.241427] pci 0000:00:0a.0: BAR 0 [mem 0x3815350000-0x381535ffff 64bit] <6>[ 2.241441] pci 0000:00:0a.0: enabling Extended Tags <6>[ 2.241678] pci 0000:00:0b.0: [8086:643e] type 00 class 0x120000 PCIe Root Complex Integrated Endpoint <6>[ 2.241707] pci 0000:00:0b.0: BAR 0 [mem 0x3810000000-0x3811ffffff 64bit] <6>[ 2.241714] pci 0000:00:0b.0: BAR 4 [mem 0x3815372000-0x3815372fff 64bit] <6>[ 2.242166] pci 0000:00:0d.0: [8086:a831] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 2.242219] pci 0000:00:0d.0: BAR 0 [mem 0x3815340000-0x381534ffff 64bit] <6>[ 2.242290] pci 0000:00:0d.0: PME# supported from D3hot D3cold <6>[ 2.244203] pci 0000:00:0d.2: [8086:a833] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 2.244256] pci 0000:00:0d.2: BAR 0 [mem 0x38152c0000-0x38152fffff 64bit] <6>[ 2.244263] pci 0000:00:0d.2: BAR 2 [mem 0x3815371000-0x3815371fff 64bit] <6>[ 2.244322] pci 0000:00:0d.2: supports D1 D2 <6>[ 2.244326] pci 0000:00:0d.2: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.245617] pci 0000:00:0d.3: [8086:a834] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 2.245669] pci 0000:00:0d.3: BAR 0 [mem 0x3815280000-0x38152bffff 64bit] <6>[ 2.245677] pci 0000:00:0d.3: BAR 2 [mem 0x3815370000-0x3815370fff 64bit] <6>[ 2.245735] pci 0000:00:0d.3: supports D1 D2 <6>[ 2.245739] pci 0000:00:0d.3: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.247056] pci 0000:00:12.0: [8086:a845] type 00 class 0x070000 conventional PCI endpoint <6>[ 2.247111] pci 0000:00:12.0: BAR 0 [mem 0x3815330000-0x381533ffff 64bit] <6>[ 2.247177] pci 0000:00:12.0: PME# supported from D0 D3hot <6>[ 2.249998] pci 0000:00:13.0: [8086:a862] type 00 class 0x078000 conventional PCI endpoint <6>[ 2.250088] pci 0000:00:13.0: BAR 0 [mem 0x381536f000-0x381536ffff 64bit] <6>[ 2.250191] pci 0000:00:13.0: PME# supported from D3hot <6>[ 2.250660] pci 0000:00:14.0: [8086:a87d] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 2.250713] pci 0000:00:14.0: BAR 0 [mem 0x3815320000-0x381532ffff 64bit] <6>[ 2.250780] pci 0000:00:14.0: PME# supported from D3hot D3cold <6>[ 2.252921] pci 0000:00:14.2: [8086:a87f] type 00 class 0x050000 conventional PCI endpoint <6>[ 2.252985] pci 0000:00:14.2: BAR 0 [mem 0x3815360000-0x3815367fff 64bit] <6>[ 2.252994] pci 0000:00:14.2: BAR 2 [mem 0x381536e000-0x381536efff 64bit] <6>[ 2.253325] pci 0000:00:15.0: [8086:a878] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.253437] pci 0000:00:15.0: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.263883] pci 0000:00:15.1: [8086:a879] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.263956] pci 0000:00:15.1: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.275528] pci 0000:00:15.2: [8086:a87a] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.275620] pci 0000:00:15.2: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.291741] pci 0000:00:15.3: [8086:a87b] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.291954] pci 0000:00:15.3: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.304327] pci 0000:00:16.0: [8086:a870] type 00 class 0x078000 conventional PCI endpoint <6>[ 2.304470] pci 0000:00:16.0: BAR 0 [mem 0x3815369000-0x3815369fff 64bit] <6>[ 2.304627] pci 0000:00:16.0: PME# supported from D3hot <6>[ 2.309590] pci 0000:00:16.3: [8086:a873] type 00 class 0x070002 conventional PCI endpoint <6>[ 2.309674] pci 0000:00:16.3: BAR 0 [io 0x4020-0x4027] <6>[ 2.309683] pci 0000:00:16.3: BAR 1 [mem 0x94421000-0x94421fff] <6>[ 2.310090] pci 0000:00:1c.0: [8086:a839] type 01 class 0x060400 PCIe Root Port <6>[ 2.310137] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.310148] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 2.310158] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 2.310316] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold <6>[ 2.310407] pci 0000:00:1c.0: PTM enabled (root), 4ns granularity <6>[ 2.315518] pci 0000:00:1c.4: [8086:a83c] type 01 class 0x060400 PCIe Root Port <6>[ 2.315623] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.315676] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 2.316108] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold <6>[ 2.316313] pci 0000:00:1c.4: PTM enabled (root), 4ns granularity <6>[ 2.321370] pci 0000:00:1f.0: [8086:a807] type 00 class 0x060100 conventional PCI endpoint <6>[ 2.322859] pci 0000:00:1f.3: [8086:a828] type 00 class 0x040100 conventional PCI endpoint <6>[ 2.322974] pci 0000:00:1f.3: BAR 0 [mem 0x3815200000-0x381527ffff 64bit] <6>[ 2.322988] pci 0000:00:1f.3: BAR 4 [mem 0x3815000000-0x38151fffff 64bit] <6>[ 2.323103] pci 0000:00:1f.3: PME# supported from D3hot D3cold <6>[ 2.323610] pci 0000:00:1f.4: [8086:a822] type 00 class 0x0c0500 conventional PCI endpoint <6>[ 2.323705] pci 0000:00:1f.4: BAR 0 [mem 0x3815368000-0x38153680ff 64bit] <6>[ 2.323718] pci 0000:00:1f.4: BAR 4 [io 0xefa0-0xefbf] <6>[ 2.325216] pci 0000:00:1f.5: [8086:a823] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.325399] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff] <6>[ 2.325658] pci 0000:00:1f.6: [8086:550e] type 00 class 0x020000 conventional PCI endpoint <6>[ 2.325720] pci 0000:00:1f.6: BAR 0 [mem 0x94400000-0x9441ffff] <6>[ 2.325787] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold <6>[ 2.327180] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 2.327351] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 2.327525] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 2.328046] pci 0000:7f:00.0: [10ec:8161] type 00 class 0x020000 PCIe Endpoint <6>[ 2.328118] pci 0000:7f:00.0: BAR 0 [io 0x3000-0x30ff] <6>[ 2.328129] pci 0000:7f:00.0: BAR 2 [mem 0x94304000-0x94304fff 64bit] <6>[ 2.328138] pci 0000:7f:00.0: BAR 4 [mem 0x94300000-0x94303fff 64bit] <6>[ 2.328304] pci 0000:7f:00.0: supports D1 D2 <6>[ 2.328307] pci 0000:7f:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.328929] pci 0000:00:1c.0: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.331132] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.333016] pci 0000:80:00.0: [15b7:5011] type 00 class 0x010802 PCIe Endpoint <6>[ 2.333074] pci 0000:80:00.0: BAR 0 [mem 0x94200000-0x94203fff 64bit] <6>[ 2.334465] pci 0000:00:1c.4: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.334534] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.749197] ACPI: \_SB_.PEPD: Duplicate LPS0 _DSM functions (mask: 0x1) <6>[ 13.194357] Low-power S0 idle used by default for system suspend <6>[ 13.247622] ACPI: EC: interrupt unblocked <6>[ 13.247634] ACPI: EC: event unblocked <6>[ 13.247653] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 13.247659] ACPI: EC: GPE=0x6e <6>[ 13.247665] ACPI: \_SB_.PC00.LPCB.H_EC: Boot ECDT EC initialization complete <6>[ 13.247674] ACPI: \_SB_.PC00.LPCB.H_EC: EC: Used to handle transactions and events <6>[ 13.248284] iommu: Default domain type: Translated <6>[ 13.248284] iommu: DMA domain TLB invalidation policy: lazy mode <5>[ 13.255659] SCSI subsystem initialized <7>[ 13.256787] libata version 3.00 loaded. <6>[ 13.257098] ACPI: bus type USB registered <6>[ 13.257098] usbcore: registered new interface driver usbfs <6>[ 13.257098] usbcore: registered new interface driver hub <6>[ 13.257164] usbcore: registered new device driver usb <6>[ 13.257533] pps_core: LinuxPPS API ver. 1 registered <6>[ 13.257544] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 13.257593] PTP clock support registered <6>[ 13.258934] EDAC MC: Ver: 3.0.0 <6>[ 13.260943] efivars: Registered efivars operations <6>[ 13.267563] NetLabel: Initializing <6>[ 13.267574] NetLabel: domain hash size = 128 <6>[ 13.267584] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO <6>[ 13.267749] NetLabel: unlabeled traffic allowed by default <6>[ 13.267788] mctp: management component transport protocol core <6>[ 13.267800] NET: Registered PF_MCTP protocol family <6>[ 13.267912] PCI: Using ACPI for IRQ routing <7>[ 13.312896] PCI: pci_cache_line_size set to 64 bytes <6>[ 13.313185] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]: can't claim; no compatible bridge window <7>[ 13.313338] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] <7>[ 13.313357] e820: reserve RAM buffer [mem 0x68f28000-0x6bffffff] <7>[ 13.313365] e820: reserve RAM buffer [mem 0x68f7d000-0x6bffffff] <7>[ 13.313371] e820: reserve RAM buffer [mem 0x6cac1000-0x6fffffff] <7>[ 13.313377] e820: reserve RAM buffer [mem 0x87f800000-0x87fffffff] <6>[ 13.314735] pci 0000:00:02.0: vgaarb: setting as boot VGA device <6>[ 13.314757] pci 0000:00:02.0: vgaarb: bridge control possible <6>[ 13.314767] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none <6>[ 13.314798] vgaarb: loaded <7>[ 13.318163] Monitor-Mwait will be used to enter C-1 state <7>[ 13.318192] Monitor-Mwait will be used to enter C-2 state <7>[ 13.318192] Monitor-Mwait will be used to enter C-3 state <6>[ 13.325723] clocksource: Switched to clocksource tsc-early <5>[ 13.338503] VFS: Disk quotas dquot_6.6.0 <6>[ 13.338564] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 13.341429] AppArmor: AppArmor Filesystem Enabled <6>[ 13.341880] pnp: PnP ACPI init <6>[ 13.344075] system 00:00: [io 0x0680-0x069f] has been reserved <6>[ 13.344101] system 00:00: [io 0x164e-0x164f] has been reserved <6>[ 13.347561] system 00:02: [io 0x06a4] has been reserved <6>[ 13.347581] system 00:02: [io 0x06a0] has been reserved <6>[ 13.399581] system 00:03: [mem 0xfedc0000-0xfedc7fff] has been reserved <6>[ 13.399604] system 00:03: [mem 0xd8000000-0xd8000fff] has been reserved <6>[ 13.399628] system 00:03: [mem 0x00000000-0x00000fff] could not be reserved <6>[ 13.399646] system 00:03: [mem 0xc0000000-0xcfffffff] has been reserved <6>[ 13.399663] system 00:03: [mem 0xfed20000-0xfed7ffff] has been reserved <6>[ 13.399684] system 00:03: [mem 0xfc800000-0xfc81ffff] could not be reserved <6>[ 13.399705] system 00:03: [mem 0xfed45000-0xfed8ffff] could not be reserved <6>[ 13.399722] system 00:03: [mem 0xfee00000-0xfeefffff] has been reserved <6>[ 13.408454] system 00:04: [io 0x2000-0x20fe] has been reserved <6>[ 13.414675] system 00:06: [io 0x1854-0x1857] has been reserved <6>[ 13.415078] system 00:07: [mem 0x00000000-0x0009cfff] could not be reserved <6>[ 13.426027] pnp: PnP ACPI: found 8 devices <6>[ 13.453207] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns <6>[ 13.453811] NET: Registered PF_INET protocol family <6>[ 13.454141] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 13.459725] tcp_listen_portaddr_hash hash table entries: 16384 (order: 8, 1179648 bytes, linear) <6>[ 13.460146] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 13.460632] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 13.461670] TCP bind hash table entries: 65536 (order: 11, 9437184 bytes, vmalloc hugepage) <6>[ 13.463652] TCP: Hash tables configured (established 262144 bind 65536) <6>[ 13.464248] UDP hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 13.465605] UDP-Lite hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 13.466969] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 13.467062] pci 0000:00:07.0: bridge window [io 0x1000-0x0fff] to [bus 01-2a] add_size 1000 <6>[ 13.467080] pci 0000:00:07.1: bridge window [io 0x1000-0x0fff] to [bus 2b-54] add_size 1000 <6>[ 13.467093] pci 0000:00:07.2: bridge window [io 0x1000-0x0fff] to [bus 55-7e] add_size 1000 <6>[ 13.467155] pci 0000:00:07.0: bridge window [io 0x5000-0x5fff]: assigned <6>[ 13.467165] pci 0000:00:07.1: bridge window [io 0x6000-0x6fff]: assigned <6>[ 13.467174] pci 0000:00:07.2: bridge window [io 0x7000-0x7fff]: assigned <6>[ 13.467185] pci 0000:00:15.0: BAR 0 [mem 0x381536a000-0x381536afff 64bit]: assigned <6>[ 13.467215] pci 0000:00:15.1: BAR 0 [mem 0x381536b000-0x381536bfff 64bit]: assigned <6>[ 13.467241] pci 0000:00:15.2: BAR 0 [mem 0x381536c000-0x381536cfff 64bit]: assigned <6>[ 13.467266] pci 0000:00:15.3: BAR 0 [mem 0x381536d000-0x381536dfff 64bit]: assigned <6>[ 13.467292] pci 0000:00:1f.5: BAR 0 [mem 0x80800000-0x80800fff]: assigned <6>[ 13.467338] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 13.467352] pci 0000:00:07.0: bridge window [io 0x5000-0x5fff] <6>[ 13.467364] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 13.467375] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 13.467391] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 13.467404] pci 0000:00:07.1: bridge window [io 0x6000-0x6fff] <6>[ 13.467415] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 13.467427] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 13.467442] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 13.467451] pci 0000:00:07.2: bridge window [io 0x7000-0x7fff] <6>[ 13.467462] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 13.467474] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 13.467490] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 13.467498] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 13.467509] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 13.467523] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 13.467559] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 13.467608] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] <6>[ 13.467617] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] <6>[ 13.467625] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] <6>[ 13.467634] pci_bus 0000:00: resource 7 [mem 0x80800000-0xbfffffff window] <6>[ 13.467643] pci_bus 0000:00: resource 8 [mem 0x2000000000-0x3fbfffffff window] <6>[ 13.467652] pci_bus 0000:01: resource 0 [io 0x5000-0x5fff] <6>[ 13.467660] pci_bus 0000:01: resource 1 [mem 0x8e000000-0x93ffffff] <6>[ 13.467668] pci_bus 0000:01: resource 2 [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 13.467678] pci_bus 0000:2b: resource 0 [io 0x6000-0x6fff] <6>[ 13.467686] pci_bus 0000:2b: resource 1 [mem 0x88000000-0x8dffffff] <6>[ 13.467694] pci_bus 0000:2b: resource 2 [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 13.467704] pci_bus 0000:55: resource 0 [io 0x7000-0x7fff] <6>[ 13.467711] pci_bus 0000:55: resource 1 [mem 0x82000000-0x87ffffff] <6>[ 13.467719] pci_bus 0000:55: resource 2 [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 13.467730] pci_bus 0000:7f: resource 0 [io 0x3000-0x3fff] <6>[ 13.467737] pci_bus 0000:7f: resource 1 [mem 0x94300000-0x943fffff] <6>[ 13.467745] pci_bus 0000:80: resource 1 [mem 0x94200000-0x942fffff] <6>[ 13.469238] pci 0000:00:0d.0: enabling device (0000 -> 0002) <6>[ 13.472263] PCI: CLS 0 bytes, default 64 <6>[ 13.472419] DMAR: No RMRR found <6>[ 13.472433] DMAR: No ATSR found <6>[ 13.472440] DMAR: dmar1: Using Queued invalidation <6>[ 13.472451] DMAR: dmar0: Using Queued invalidation <6>[ 13.472461] DMAR: dmar2: Using Queued invalidation <6>[ 13.473890] pci 0000:00:04.0: Adding to iommu group 0 <6>[ 13.474029] pci 0000:00:05.0: Adding to iommu group 1 <6>[ 13.474157] pci 0000:00:0a.0: Adding to iommu group 2 <6>[ 13.474251] pci 0000:00:0b.0: Adding to iommu group 3 <6>[ 13.479015] pci 0000:00:02.0: Adding to iommu group 4 <6>[ 13.480937] pci 0000:00:00.0: Adding to iommu group 5 <6>[ 13.481039] pci 0000:00:07.0: Adding to iommu group 6 <6>[ 13.481139] pci 0000:00:07.1: Adding to iommu group 7 <6>[ 13.481236] pci 0000:00:07.2: Adding to iommu group 8 <6>[ 13.481350] pci 0000:00:0d.0: Adding to iommu group 9 <6>[ 13.481412] pci 0000:00:0d.2: Adding to iommu group 9 <6>[ 13.481474] pci 0000:00:0d.3: Adding to iommu group 9 <6>[ 13.481575] pci 0000:00:12.0: Adding to iommu group 10 <6>[ 13.481669] pci 0000:00:13.0: Adding to iommu group 11 <6>[ 13.481774] pci 0000:00:14.0: Adding to iommu group 12 <6>[ 13.481836] pci 0000:00:14.2: Adding to iommu group 12 <6>[ 13.481972] pci 0000:00:15.0: Adding to iommu group 13 <6>[ 13.482037] pci 0000:00:15.1: Adding to iommu group 13 <6>[ 13.482101] pci 0000:00:15.2: Adding to iommu group 13 <6>[ 13.482167] pci 0000:00:15.3: Adding to iommu group 13 <6>[ 13.482270] pci 0000:00:16.0: Adding to iommu group 14 <6>[ 13.482336] pci 0000:00:16.3: Adding to iommu group 14 <6>[ 13.482426] pci 0000:00:1c.0: Adding to iommu group 15 <6>[ 13.482540] pci 0000:00:1c.4: Adding to iommu group 16 <6>[ 13.482678] pci 0000:00:1f.0: Adding to iommu group 17 <6>[ 13.482748] pci 0000:00:1f.3: Adding to iommu group 17 <6>[ 13.482815] pci 0000:00:1f.4: Adding to iommu group 17 <6>[ 13.482881] pci 0000:00:1f.5: Adding to iommu group 17 <6>[ 13.482953] pci 0000:00:1f.6: Adding to iommu group 17 <6>[ 13.483063] pci 0000:7f:00.0: Adding to iommu group 18 <6>[ 13.483176] pci 0000:80:00.0: Adding to iommu group 19 <6>[ 13.497141] DMAR: Intel(R) Virtualization Technology for Directed I/O <6>[ 13.497160] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) <6>[ 13.497169] software IO TLB: mapped [mem 0x0000000063ac2000-0x0000000067ac2000] (64MB) <6>[ 13.503179] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 13.503413] clocksource: Switched to clocksource tsc <6>[ 13.503654] platform rtc_cmos: registered platform RTC device (no PNP device found) <5>[ 13.514518] Initialise system trusted keyrings <5>[ 13.514614] Key type blacklist registered <6>[ 13.515297] workingset: timestamp_bits=36 max_order=23 bucket_order=0 <6>[ 13.529260] squashfs: version 4.0 (2009/01/31) Phillip Lougher <6>[ 13.529409] ntfs3: Enabled Linux POSIX ACLs support <6>[ 13.529416] ntfs3: Read-only LZX/Xpress compression included <5>[ 13.530494] integrity: Platform Keyring initialized <5>[ 13.530523] integrity: Machine keyring initialized <6>[ 13.537153] xor: automatically using best checksumming function avx <5>[ 13.537166] Key type asymmetric registered <5>[ 13.537180] Asymmetric key parser 'x509' registered <6>[ 13.537321] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) <6>[ 13.538242] io scheduler mq-deadline registered <6>[ 13.540213] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 13.541989] pcieport 0000:00:07.0: PME: Signaling with IRQ 126 <6>[ 13.542396] pcieport 0000:00:07.0: AER: enabled with IRQ 126 <6>[ 13.543669] pcieport 0000:00:07.1: PME: Signaling with IRQ 127 <6>[ 13.543997] pcieport 0000:00:07.1: AER: enabled with IRQ 127 <6>[ 13.545260] pcieport 0000:00:07.2: PME: Signaling with IRQ 128 <6>[ 13.545588] pcieport 0000:00:07.2: AER: enabled with IRQ 128 <6>[ 13.546755] pcieport 0000:00:1c.0: PME: Signaling with IRQ 129 <6>[ 13.547300] pcieport 0000:00:1c.0: AER: enabled with IRQ 129 <6>[ 13.551384] pcieport 0000:00:1c.4: PME: Signaling with IRQ 130 <6>[ 13.551965] pcieport 0000:00:1c.4: AER: enabled with IRQ 130 <6>[ 13.554097] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:16/PNP0C09:00/PNP0C0D:00/input/input0 <6>[ 13.554335] ACPI: button: Lid Switch [LID0] <6>[ 13.554645] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1 <6>[ 13.554854] ACPI: button: Sleep Button [SLPB] <6>[ 13.555139] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 <6>[ 13.555618] ACPI: button: Power Button [PWRB] <6>[ 13.710860] thermal LNXTHERM:00: registered as thermal_zone0 <6>[ 13.710879] ACPI: thermal: Thermal Zone [TZ00] (52 C) <6>[ 13.713256] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled <6>[ 13.713391] ACPI: battery: Slot [BAT1] (battery absent) <6>[ 13.716534] ACPI: battery: Slot [BAT0] (battery present) <6>[ 13.738945] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A <6>[ 13.778731] serial 0000:00:12.0: enabling device (0000 -> 0002) <6>[ 13.781891] serial 0000:00:16.3: enabling device (0001 -> 0003) <6>[ 13.807232] 0000:00:16.3: ttyS4 at I/O 0x4020 (irq = 19, base_baud = 115200) is a 16550A <5>[ 13.811910] hpet_acpi_add: no address or irqs in _CRS <6>[ 13.812201] Linux agpgart interface v0.103 <6>[ 13.814847] ACPI: bus type drm_connector registered <7>[ 13.817052] initcall simpledrm_platform_driver_init blacklisted <6>[ 13.856806] loop: module loaded <6>[ 13.925115] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002) <6>[ 14.098754] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002) <6>[ 14.213923] intel-lpss 0000:00:15.2: enabling device (0000 -> 0002) <6>[ 14.327198] intel-lpss 0000:00:15.3: enabling device (0000 -> 0002) <5>[ 14.440141] Key type psk registered <6>[ 14.444733] nvme 0000:80:00.0: platform quirk: setting simple suspend <6>[ 14.446169] tun: Universal TUN/TAP device driver, 1.6 <6>[ 14.446411] nvme nvme0: pci function 0000:80:00.0 <6>[ 14.447409] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 14.447511] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 <6>[ 14.449242] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 14.452693] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 14.452786] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 <6>[ 14.452814] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 14.453538] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 14.453566] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 14.453578] usb usb1: Product: xHCI Host Controller <6>[ 14.453587] usb usb1: Manufacturer: Linux 6.18.0-rc2-lgci-xe-xe-3969-71929a54e8bb5da29+ xhci-hcd <6>[ 14.453601] usb usb1: SerialNumber: 0000:00:0d.0 <6>[ 14.455307] hub 1-0:1.0: USB hub found <6>[ 14.455428] hub 1-0:1.0: 1 port detected <6>[ 14.461604] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 14.461631] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 14.461649] usb usb2: Product: xHCI Host Controller <6>[ 14.461661] usb usb2: Manufacturer: Linux 6.18.0-rc2-lgci-xe-xe-3969-71929a54e8bb5da29+ xhci-hcd <6>[ 14.461682] usb usb2: SerialNumber: 0000:00:0d.0 <6>[ 14.463028] hub 2-0:1.0: USB hub found <6>[ 14.463094] hub 2-0:1.0: 3 ports detected <6>[ 14.486756] nvme nvme0: 8/0/0 default/read/poll queues <6>[ 14.490375] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 14.490417] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 <6>[ 14.492312] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 14.495349] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 14.495376] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 <6>[ 14.495397] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 14.495661] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 14.495676] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 14.495686] usb usb3: Product: xHCI Host Controller <6>[ 14.495694] usb usb3: Manufacturer: Linux 6.18.0-rc2-lgci-xe-xe-3969-71929a54e8bb5da29+ xhci-hcd <6>[ 14.495706] usb usb3: SerialNumber: 0000:00:14.0 <6>[ 14.496682] hub 3-0:1.0: USB hub found <6>[ 14.496733] hub 3-0:1.0: 8 ports detected <6>[ 14.503266] nvme0n1: p1 p2 <6>[ 14.528892] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 14.528922] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 14.528933] usb usb4: Product: xHCI Host Controller <6>[ 14.528941] usb usb4: Manufacturer: Linux 6.18.0-rc2-lgci-xe-xe-3969-71929a54e8bb5da29+ xhci-hcd <6>[ 14.528953] usb usb4: SerialNumber: 0000:00:14.0 <6>[ 14.529799] hub 4-0:1.0: USB hub found <6>[ 14.529848] hub 4-0:1.0: 2 ports detected <6>[ 14.537167] usbcore: registered new interface driver usb-storage <6>[ 14.537355] usbcore: registered new interface driver usbserial_generic <6>[ 14.537469] usbserial: USB Serial support registered for generic <6>[ 14.537544] usbcore: registered new interface driver ftdi_sio <6>[ 14.537598] usbserial: USB Serial support registered for FTDI USB Serial Device <6>[ 14.537671] usbcore: registered new interface driver pl2303 <6>[ 14.537708] usbserial: USB Serial support registered for pl2303 <6>[ 14.537845] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 <4>[ 14.537855] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp <3>[ 15.248608] i8042: Can't read CTR while initializing i8042 <3>[ 15.248623] i8042 i8042: probe with driver i8042 failed with error -5 <6>[ 15.249270] mousedev: PS/2 mouse device common for all mice <6>[ 15.250382] rtc_cmos rtc_cmos: RTC can wake from S4 <6>[ 15.252357] rtc_cmos rtc_cmos: registered as rtc0 <6>[ 15.252579] rtc_cmos rtc_cmos: setting system clock to 2025-10-22T23:39:41 UTC (1761176381) <6>[ 15.252770] rtc_cmos rtc_cmos: alarms up to one month, y3k, 114 bytes nvram <6>[ 15.252828] i2c_dev: i2c /dev entries driver <6>[ 15.260027] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=5 (nowayout=0) <6>[ 15.260043] softdog: soft_reboot_cmd= soft_active_on_boot=0 <4>[ 15.260055] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. <6>[ 15.260103] device-mapper: uevent: version 1.0.3 <6>[ 15.260510] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev <6>[ 15.260531] intel_pstate: Intel P-state driver initializing <6>[ 15.264364] Hybrid CPU capacity scaling enabled <6>[ 15.264724] processor cpu0: EM: created perf domain <6>[ 15.264991] processor cpu1: EM: created perf domain <6>[ 15.265247] processor cpu2: EM: created perf domain <6>[ 15.265503] processor cpu3: EM: created perf domain <6>[ 15.265766] processor cpu4: EM: created perf domain <6>[ 15.266022] processor cpu5: EM: created perf domain <6>[ 15.266272] processor cpu6: EM: created perf domain <6>[ 15.266525] processor cpu7: EM: created perf domain <6>[ 15.268273] intel_pstate: HWP enabled <6>[ 15.268288] sdhci: Secure Digital Host Controller Interface driver <6>[ 15.268297] sdhci: Copyright(c) Pierre Ossman <6>[ 15.268574] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 15.272401] Relocating firmware framebuffer to offset 0x0000000000800000[d] within [mem 0x2000000000-0x200fffffff flags 0x14220c] <6>[ 15.273608] drop_monitor: Initializing network drop monitor service <6>[ 15.273903] NET: Registered PF_INET6 protocol family <6>[ 15.275681] Segment Routing with IPv6 <6>[ 15.275718] In-situ OAM (IOAM) with IPv6 <6>[ 15.275766] NET: Registered PF_PACKET protocol family <5>[ 15.276078] Key type dns_resolver registered <4>[ 15.280669] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' <6>[ 15.281089] microcode: Current revision: 0x00000121 <6>[ 15.281844] IPI shorthand broadcast: enabled <6>[ 15.297893] sched_clock: Marking stable (15287001966, 9894100)->(15386047358, -89151292) <6>[ 15.298671] registered taskstats version 1 <5>[ 15.300219] Loading compiled-in X.509 certificates <6>[ 15.343842] Demotion targets for Node 0: null <6>[ 15.344096] kmemleak: Kernel memory leak detector initialized (mem pool available: 14946) <6>[ 15.344101] kmemleak: Automatic memory scanning thread started <5>[ 15.344332] Key type .fscrypt registered <5>[ 15.344337] Key type fscrypt-provisioning registered <6>[ 15.347248] Btrfs loaded, zoned=yes, fsverity=yes <5>[ 15.349848] Key type encrypted registered <6>[ 15.349854] AppArmor: AppArmor sha256 policy hashing enabled <6>[ 15.349950] ima: No TPM chip found, activating TPM-bypass! <5>[ 15.349964] Loading compiled-in module X.509 certificates <5>[ 15.350584] Loaded X.509 cert 'Build time autogenerated kernel key: ea0b8a055eef8c5dcafef4ddf4a185a44c0de2d5' <6>[ 15.350594] ima: Allocated hash algorithm: sha256 <6>[ 15.350636] ima: No architecture policies found <6>[ 15.350712] evm: Initialising EVM extended attributes: <6>[ 15.350716] evm: security.selinux <6>[ 15.350719] evm: security.SMACK64 <6>[ 15.350722] evm: security.SMACK64EXEC <6>[ 15.350725] evm: security.SMACK64TRANSMUTE <6>[ 15.350728] evm: security.SMACK64MMAP <6>[ 15.350731] evm: security.apparmor <6>[ 15.350734] evm: security.ima <6>[ 15.350736] evm: security.capability <6>[ 15.350739] evm: HMAC attrs: 0x1 <6>[ 15.352762] PM: Magic number: 13:253:707 <6>[ 15.352839] acpi SPI2011:00: hash matches <6>[ 15.352954] netconsole: network logging started <6>[ 15.353502] RAS: Correctable Errors collector initialized. <6>[ 15.353631] clk: Disabling unused clocks <6>[ 15.353640] PM: genpd: Disabling unused power domains <4>[ 15.354162] check access for rdinit=/init failed: -2, ignoring <6>[ 15.354170] md: Waiting for all devices to be available before autodetect <6>[ 15.354175] md: If you don't use raid, use raid=noautodetect <6>[ 15.354181] md: Autodetecting RAID arrays. <6>[ 15.354479] md: autorun ... <6>[ 15.354482] md: ... autorun DONE. <6>[ 15.395469] EXT4-fs (nvme0n1p2): mounted filesystem 7dfac1f5-10ea-4066-a63e-e14654e0601e ro with ordered data mode. Quota mode: none. <6>[ 15.395535] VFS: Mounted root (ext4 filesystem) readonly on device 259:2. <6>[ 15.396121] devtmpfs: mounted <6>[ 15.412267] Freeing unused decrypted memory: 2036K <6>[ 15.413201] Freeing unused kernel image (initmem) memory: 5704K <6>[ 15.413224] Write protecting the kernel read-only data: 36864k <6>[ 15.413916] Freeing unused kernel image (text/rodata gap) memory: 1208K <6>[ 15.414323] Freeing unused kernel image (rodata/data gap) memory: 700K <6>[ 15.418812] x86/mm: Checked W+X mappings: passed, no W+X pages found. <6>[ 15.419476] Run /sbin/init as init process <7>[ 15.419480] with arguments: <7>[ 15.419481] /sbin/init <7>[ 15.419482] with environment: <7>[ 15.419483] HOME=/ <7>[ 15.419483] TERM=linux <7>[ 15.464734] systemd[1]: Inserted module 'autofs4' <7>[ 15.487782] systemd[1]: systemd 255.4-1ubuntu8.5 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <7>[ 15.487855] systemd[1]: Detected architecture x86-64. <7>[ 15.490557] systemd[1]: Hostname set to . <7>[ 15.741402] systemd[1]: Queued start job for default target graphical.target. <7>[ 15.762305] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. <7>[ 15.764153] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck. <7>[ 15.765533] systemd[1]: Created slice user.slice - User and Session Slice. <7>[ 15.765780] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. <7>[ 15.766470] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point. <7>[ 15.766579] systemd[1]: Expecting device dev-disk-by\x2duuid-BB9D\x2d0E2E.device - /dev/disk/by-uuid/BB9D-0E2E... <7>[ 15.766658] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. <7>[ 15.766742] systemd[1]: Reached target slices.target - Slice Units. <7>[ 15.766814] systemd[1]: Reached target snapd.mounts-pre.target - Mounting snaps. <7>[ 15.766884] systemd[1]: Reached target snapd.mounts.target - Mounted snaps. <7>[ 15.767009] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. <7>[ 15.767252] systemd[1]: Listening on dm-event.socket - Device-mapper event daemon FIFOs. <7>[ 15.767623] systemd[1]: Listening on lvm2-lvmpolld.socket - LVM2 poll daemon socket. <7>[ 15.767940] systemd[1]: Listening on multipathd.socket - multipathd control socket. <7>[ 15.768277] systemd[1]: Listening on syslog.socket - Syslog Socket. <7>[ 15.768533] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket. <7>[ 15.768722] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. <7>[ 15.769021] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). <7>[ 15.769328] systemd[1]: Listening on systemd-journald.socket - Journal Socket. <7>[ 15.769594] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. <7>[ 15.769761] systemd[1]: systemd-pcrextend.socket - TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 15.770269] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. <7>[ 15.770581] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. <7>[ 15.774044] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... <7>[ 15.776870] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... <7>[ 15.779579] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... <7>[ 15.782606] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System... <7>[ 15.789447] systemd[1]: Starting systemd-journald.service - Journal Service... <7>[ 15.792764] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout... <7>[ 15.795636] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... <7>[ 15.798651] systemd[1]: Starting lvm2-monitor.service - Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... <7>[ 15.801841] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... <7>[ 15.805680] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... <7>[ 15.808476] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... <7>[ 15.813673] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... <7>[ 15.817346] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... <7>[ 15.820194] systemd-journald[205]: Collecting audit messages is disabled. <7>[ 15.821732] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... <7>[ 15.826126] systemd[1]: Starting modprobe@nvme_fabrics.service - Load Kernel Module nvme_fabrics... <7>[ 15.826332] systemd[1]: netplan-ovs-cleanup.service - OpenVSwitch configuration for cleanup was skipped because of an unmet condition check (ConditionFileIsExecutable=/usr/bin/ovs-vsctl). <7>[ 15.831224] systemd[1]: Starting systemd-fsck-root.service - File System Check on Root Device... <6>[ 15.834392] pstore: Using crash dump compression: deflate <6>[ 15.835350] pstore: Registered efi_pstore as persistent store backend <7>[ 15.840847] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... <7>[ 15.841168] systemd[1]: systemd-pcrmachine.service - TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 15.841238] systemd[1]: systemd-tpm2-setup-early.service - TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <6>[ 15.843643] fuse: init (API version 7.45) <7>[ 15.845955] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... <7>[ 15.851887] systemd[1]: Started systemd-journald.service - Journal Service. <6>[ 15.980883] EXT4-fs (nvme0n1p2): re-mounted 7dfac1f5-10ea-4066-a63e-e14654e0601e r/w. <6>[ 16.006007] Adding 8388604k swap on /swap.img. Priority:-2 extents:66 across:320602112k SS <7>[ 16.017386] systemd-journald[205]: Received client request to flush runtime journal. <7>[ 16.029168] systemd-journald[205]: /var/log/journal/d99f231fc73949389b52e126c183b290/system.journal: Journal file uses a different sequence number ID, rotating. <7>[ 16.029180] systemd-journald[205]: Rotating system journal. <4>[ 16.731392] nvme nvme0: using unchecked data buffer <6>[ 16.892776] intel_vsec 0000:00:0a.0: enabling device (0000 -> 0002) <6>[ 16.913101] intel_pmc_ssram_telemetry 0000:00:14.2: enabling device (0000 -> 0002) <6>[ 16.933504] input: Intel HID events as /devices/platform/INTC107B:00/input/input3 <6>[ 16.939536] intel-hid INTC107B:00: platform supports 5 button array <6>[ 16.952832] input: Intel HID 5 button array as /devices/platform/INTC107B:00/input/input4 <5>[ 17.012769] audit: type=1400 audit(1761176383.258:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name=4D6F6E676F444220436F6D70617373 pid=423 comm="apparmor_parser" <5>[ 17.013283] audit: type=1400 audit(1761176383.259:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="Discord" pid=422 comm="apparmor_parser" <5>[ 17.014040] audit: type=1400 audit(1761176383.260:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="1password" pid=421 comm="apparmor_parser" <5>[ 17.014739] audit: type=1400 audit(1761176383.260:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="QtWebEngineProcess" pid=424 comm="apparmor_parser" <5>[ 17.017758] audit: type=1400 audit(1761176383.263:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="balena-etcher" pid=425 comm="apparmor_parser" <5>[ 17.020505] audit: type=1400 audit(1761176383.266:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="brave" pid=426 comm="apparmor_parser" <5>[ 17.023131] audit: type=1400 audit(1761176383.268:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="buildah" pid=427 comm="apparmor_parser" <5>[ 17.025885] audit: type=1400 audit(1761176383.271:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="busybox" pid=429 comm="apparmor_parser" <5>[ 17.027657] audit: type=1400 audit(1761176383.273:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="cam" pid=430 comm="apparmor_parser" <5>[ 17.029381] audit: type=1400 audit(1761176383.275:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ch-checkns" pid=431 comm="apparmor_parser" <3>[ 17.067125] int3472-tps68470 i2c-INT3472:06: TPS68470 init error -121 <3>[ 17.067288] int3472-tps68470 i2c-INT3472:06: probe with driver int3472-tps68470 failed with error -121 <6>[ 17.134137] pci 0000:00:05.0: Setting to D3hot <6>[ 17.145973] pci 0000:00:0b.0: Setting to D3hot <6>[ 17.160622] intel_pmc_core INT33A1:00: initialized <6>[ 17.467682] ACPI: bus type thunderbolt registered <6>[ 17.468891] intel_vpu 0000:00:0b.0: enabling device (0000 -> 0002) <6>[ 17.482042] intel_vpu 0000:00:0b.0: [drm] Firmware: intel/vpu/vpu_40xx_v0.0.bin, version: Jun 11 2024*LNL*ci_tag_ud202424_vpu_rc_20240611_0003*f3e8a8f27471d4127d8d92a8dc679b861ef43e43 <6>[ 17.482051] intel_vpu 0000:00:0b.0: [drm] Scheduler mode: OS <6>[ 17.512557] idma64 idma64.0: Found Intel integrated DMA 64-bit <6>[ 17.515364] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 17.515367] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 17.516307] e1000e 0000:00:1f.6: enabling device (0000 -> 0002) <6>[ 17.517546] idma64 idma64.1: Found Intel integrated DMA 64-bit <6>[ 17.517617] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode <6>[ 17.550623] idma64 idma64.2: Found Intel integrated DMA 64-bit <6>[ 17.556512] [drm] Initialized intel_vpu 1.0.0 for 0000:00:0b.0 on minor 0 <6>[ 17.558506] r8169 0000:7f:00.0: enabling device (0000 -> 0003) <6>[ 17.576254] idma64 idma64.3: Found Intel integrated DMA 64-bit <6>[ 17.642635] proc_thermal_pci 0000:00:04.0: enabling device (0400 -> 0402) <6>[ 17.650891] intel_rapl_common: Found RAPL domain package <6>[ 17.650908] intel_rapl_common: Found RAPL domain dram <6>[ 17.664780] r8169 0000:7f:00.0 eth0: RTL8168h/8111h, e4:fa:c4:a5:0e:fc, XID 541, IRQ 176 <6>[ 17.664787] r8169 0000:7f:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 17.683344] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6>[ 17.684396] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.689211] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer <6>[ 17.689215] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules <6>[ 17.689216] RAPL PMU: hw unit of domain package 2^-14 Joules <6>[ 17.689217] RAPL PMU: hw unit of domain dram 2^-14 Joules <6>[ 17.689218] RAPL PMU: hw unit of domain psys 2^-14 Joules <6>[ 17.763246] proc_thermal_pci 0000:00:04.0: msi enabled:1 msix enabled:0 <6>[ 17.771476] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 17.864780] block nvme0n1: No UUID available providing old NGUID <6>[ 18.041096] /proc/cgroups lists only v1 controllers, use cgroup.controllers of root cgroup for v2 info <6>[ 18.097064] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.140100] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock <6>[ 18.231579] intel_ish_ipc 0000:00:12.0: ISH loader: load firmware: intel/ish/ish_lnlm.bin <6>[ 18.238110] e1000e 0000:00:1f.6 eth1: (PCI Express:2.5GT/s:Width x1) 90:49:fa:0a:30:95 <6>[ 18.238119] e1000e 0000:00:1f.6 eth1: Intel(R) PRO/1000 Network Connection <6>[ 18.238245] e1000e 0000:00:1f.6 eth1: MAC: 16, PHY: 12, PBA No: FFFFFF-0FF <6>[ 18.238399] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.248733] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.256594] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.261173] intel_ish_ipc 0000:00:12.0: ISH loader: firmware loaded. size:997888 <6>[ 18.261182] intel_ish_ipc 0000:00:12.0: ISH loader: FW base version: 5.8.0.7716 <6>[ 18.261184] intel_ish_ipc 0000:00:12.0: ISH loader: FW project version: 5.8.0.12472 <6>[ 18.361048] loop0: detected capacity change from 0 to 8 <6>[ 18.405059] intel_rapl_common: Found RAPL domain package <6>[ 18.405065] intel_rapl_common: Found RAPL domain core <6>[ 18.405068] intel_rapl_common: Found RAPL domain dram <6>[ 18.405070] intel_rapl_common: Found RAPL domain psys <6>[ 18.522078] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 18.583402] spi-nor spi0.0: supply vcc not found, using dummy regulator <6>[ 18.602742] r8169 0000:7f:00.0 enp127s0: renamed from eth0 <6>[ 18.622655] e1000e 0000:00:1f.6 enp0s31f6: renamed from eth1 <6>[ 18.636882] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <5>[ 18.640699] Creating 1 MTD partitions on "0000:00:1f.5": <5>[ 18.640719] 0x000000000000-0x000002000000 : "BIOS" <6>[ 18.668869] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.935016] Generic FE-GE Realtek PHY r8169-0-7f00:00: attached PHY driver (mii_bus:phy_addr=r8169-0-7f00:00, irq=MAC) <6>[ 18.978436] Consider using thermal netlink events interface <6>[ 19.004451] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.094112] r8169 0000:7f:00.0 enp127s0: Link is Down <6>[ 19.263749] hid: raw HID events driver (C) Jiri Kosina <6>[ 19.271154] ish-hid {33AECD58-B679-4E54-9BD9-A04D34F0C226}: [hid-ish]: enum_devices_done OK, num_hid_devices=6 <6>[ 19.304433] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.310462] hid-generic 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.311560] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.312765] hid-generic 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.314987] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.315793] hid-generic 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.317127] hid-generic 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.317810] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.319410] hid-generic 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 19.320534] hid-generic 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 19.320708] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.325369] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.326848] hid-sensor-hub 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.330098] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.331523] hid-sensor-hub 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.335203] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.337335] hid-sensor-hub 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.341063] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.341253] hid-sensor-hub 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 19.343586] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.345535] hid-sensor-hub 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 19.348562] hid-sensor-hub 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 19.348748] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.352490] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.424867] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.429145] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.433708] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.437973] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.442296] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.445574] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.450492] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.455852] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.459892] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.463386] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.466362] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.469933] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.475086] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.478523] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.483016] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.487302] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.490944] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.495491] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.500306] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.506311] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 20.762505] typec port0: bound usb3-port1 (ops connector_ops) <6>[ 20.762571] typec port0: bound usb2-port1 (ops connector_ops) <6>[ 20.762613] typec port0: bound usb4_port1 (ops connector_ops [thunderbolt]) <6>[ 21.784750] typec port1: bound usb3-port2 (ops connector_ops) <6>[ 21.784795] typec port1: bound usb2-port2 (ops connector_ops) <6>[ 21.784855] typec port1: bound usb4_port3 (ops connector_ops [thunderbolt]) <6>[ 23.876419] r8169 0000:7f:00.0 enp127s0: Link is Up - 1Gbps/Full - flow control off <6>[ 29.781848] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 29.785739] pci 0000:00:1f.3: deferred probe pending: snd_hda_intel: couldn't bind with audio component <7>[ 36.667286] systemd-journald[205]: /var/log/journal/d99f231fc73949389b52e126c183b290/user-1000.journal: Journal file uses a different sequence number ID, rotating. <7>[ 57.129357] [IGT] xe_module_load: executing <4>[ 57.129449] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030 <7>[ 57.136982] [IGT] xe_module_load: starting subtest load <5>[ 57.390212] Setting dangerous option force_probe - tainting kernel <6>[ 57.393096] xe 0000:00:02.0: vgaarb: deactivate vga console <6>[ 57.394724] xe 0000:00:02.0: [drm] Found lunarlake (device ID 64a0) integrated display version 20.00 stepping B0 <7>[ 57.394735] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] LUNARLAKE 64a0:0004 dgfx:0 gfx:Xe2_LPG (20.04) media:Xe2_LPM (20.00) display:yes dma_m_s:46 tc:1 gscfi:0 cscfi:0 <7>[ 57.394865] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] Stepping = (G:B0, M:B0, B:**) <7>[ 57.394992] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] SR-IOV support: no (mode: none) <7>[ 57.397156] xe 0000:00:02.0: [drm:xe_ttm_stolen_mgr_init [xe]] Initialized stolen memory support with 58720256 bytes <7>[ 57.397419] xe 0000:00:02.0: [drm:intel_pch_detect [xe]] PCH not involved in display, using fake PCH type 1027 for south display <7>[ 57.397526] xe 0000:00:02.0: [drm:intel_dmc_wl_init [xe]] Sanitized enable_dmc_wl value: 0 (disabled) <7>[ 57.397643] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] graphic opregion physical addr: 0x6ff04018 <7>[ 57.397762] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ACPI OpRegion version 3.2.0 <7>[ 57.397861] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Public ACPI methods supported <7>[ 57.397979] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE supported <7>[ 57.398133] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE extension supported <7>[ 57.398238] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Mailbox #2 for backlight present <7>[ 57.398344] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Found valid VBT in ACPI OpRegion (RVDA) <7>[ 57.398449] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM type: LPDDR5 <7>[ 57.398568] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM channels: 8 <7>[ 57.398684] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num QGV points 4 <7>[ 57.398796] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num PSF GV points 0 <7>[ 57.398916] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 0: DCLK=2400 tRP=48 tRDPRE=40 tRAS=104 tRCD=48 tRC=152 <7>[ 57.399055] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 1: DCLK=4800 tRP=88 tRDPRE=72 tRAS=208 tRCD=88 tRC=296 <7>[ 57.399195] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 2: DCLK=6400 tRP=120 tRDPRE=80 tRAS=272 tRCD=120 tRC=392 <7>[ 57.399311] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 3: DCLK=8534 tRP=160 tRDPRE=96 tRAS=360 tRCD=160 tRC=520 <7>[ 57.399412] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 0: num_planes=0 deratedbw=23530 peakbw: 38400 <7>[ 57.399516] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 1: num_planes=0 deratedbw=36260 peakbw: 76800 <7>[ 57.399626] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.399736] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.399846] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 0: num_planes=0 deratedbw=27998 peakbw: 38400 <7>[ 57.399966] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 57.400095] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.400217] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.400320] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 0: num_planes=0 deratedbw=30935 peakbw: 38400 <7>[ 57.400421] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 57.400539] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.400655] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.400759] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 0: num_planes=0 deratedbw=32647 peakbw: 38400 <7>[ 57.400849] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 57.400954] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.401068] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.401183] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 0: num_planes=0 deratedbw=33577 peakbw: 38400 <7>[ 57.401282] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 57.401377] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.401470] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.401555] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 0: num_planes=0 deratedbw=34061 peakbw: 38400 <7>[ 57.401648] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 57.401741] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 57.401836] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 57.401953] xe 0000:00:02.0: [drm:intel_display_device_info_runtime_init [xe]] rawclk rate: 38400 kHz <7>[ 57.402386] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Set default to SSC at 120000 kHz <7>[ 57.402527] xe 0000:00:02.0: [drm:intel_bios_init [xe]] VBT signature "$VBT LUNARLAKE ", BDB version 262 <7>[ 57.402654] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 1 (size 10, min size 7) <7>[ 57.402778] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 2 (size 405, min size 5) <7>[ 57.402955] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 9 (size 100, min size 100) <7>[ 57.403098] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 12 (size 19, min size 19) <7>[ 57.403239] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 27 (size 850, min size 848) <7>[ 57.403355] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 40 (size 34, min size 34) <7>[ 57.403479] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Generating LFP data table pointers <7>[ 57.403623] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 41 (size 148, min size 148) <7>[ 57.403764] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 42 (size 1382, min size 1366) <7>[ 57.403890] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 43 (size 305, min size 305) <7>[ 57.404039] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 44 (size 136, min size 136) <7>[ 57.404189] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 52 (size 822, min size 822) <7>[ 57.404316] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 56 (size 210, min size 210) <7>[ 57.404427] xe 0000:00:02.0: [drm:intel_bios_init [xe]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7>[ 57.404536] xe 0000:00:02.0: [drm:intel_bios_init [xe]] crt_ddc_bus_pin: 2 <7>[ 57.404644] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x1806 <7>[ 57.404756] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 57.404864] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 57.404989] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 57.405116] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Skipping SDVO device mapping <7>[ 57.405243] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7>[ 57.405358] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 57.405463] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 57.405558] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port F VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 57.405652] xe 0000:00:02.0: [drm:intel_power_domains_init [xe]] Allowed DC state mask 0a <7>[ 57.405775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 57.405942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_1 <7>[ 57.406124] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 57.406298] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf <7>[ 57.406492] xe 0000:00:02.0: [drm:icl_display_core_init [xe]] Unknown memory configuration; disabling address buddy logic. <7>[ 57.406655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on <7>[ 57.406776] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 57.406883] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 57.407078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2 <6>[ 57.407232] xe 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=io+mem <7>[ 57.407250] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A <7>[ 57.407396] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B <7>[ 57.407526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C <7>[ 57.407636] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D <7>[ 57.407894] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC <7>[ 57.408389] xe 0000:00:02.0: [drm:intel_dmc_init [xe]] Loading i915/xe2lpd_dmc.bin <7>[ 57.409541] xe 0000:00:02.0: [drm:intel_fbc_init [xe]] Sanitized enable_fbc value: 1 <7>[ 57.409985] xe 0000:00:02.0: [drm:skl_wm_init [xe]] SAGV supported: yes, original SAGV block time: 12 us <7>[ 57.410126] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM0 latency not provided <7>[ 57.410243] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM1 latency 100 (100.0 usec) <7>[ 57.410342] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM2 latency 100 (100.0 usec) <7>[ 57.410435] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM3 latency 100 (100.0 usec) <7>[ 57.410523] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM4 latency 93 (93.0 usec) <7>[ 57.410618] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM5 latency 100 (100.0 usec) <7>[ 57.410711] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM0 latency 6 (6.0 usec) <7>[ 57.410803] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM1 latency 106 (106.0 usec) <7>[ 57.410894] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM2 latency 106 (106.0 usec) <7>[ 57.411019] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM3 latency 106 (106.0 usec) <7>[ 57.411132] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM4 latency 106 (106.0 usec) <7>[ 57.411243] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM5 latency 106 (106.0 usec) <7>[ 57.411571] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 0: <7>[ 57.411699] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x8f074 = 0x86fc0 <7>[ 57.411822] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x8f034 = 0xc003b400 (EVT_CTL) <7>[ 57.411966] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x8f004 = 0x4240408 (EVT_HTP) <7>[ 57.412099] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x8f044 = 0xc0023200 (EVT_CTL) <7>[ 57.412231] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x8f014 = 0x57c45700 (EVT_HTP) <7>[ 57.412354] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 1: <7>[ 57.412484] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f074 = 0x97fc0 <7>[ 57.412611] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f040 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 57.412739] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f010 = 0x28542840 (EVT_HTP) <7>[ 57.412865] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f03c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 57.413002] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f00c = 0x29802864 (EVT_HTP) <7>[ 57.413126] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f044 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 57.413249] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f014 = 0x398c394c (EVT_HTP) <7>[ 57.413377] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 2: <7>[ 57.413499] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f474 = 0x9ffc0 <7>[ 57.413621] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f440 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 57.413743] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f410 = 0xa9bca9a8 (EVT_HTP) <7>[ 57.413867] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f43c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 57.414010] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f40c = 0xaae8a9cc (EVT_HTP) <7>[ 57.414134] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f444 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 57.414254] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f414 = 0xbabcba7c (EVT_HTP) <7>[ 57.414381] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 3: <7>[ 57.414498] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f874 = 0x547c0 <7>[ 57.414603] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f840 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 57.414700] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f810 = 0x26dc26c8 (EVT_HTP) <7>[ 57.414793] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f83c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 57.414909] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f80c = 0x280826ec (EVT_HTP) <7>[ 57.415025] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f844 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 57.415138] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f814 = 0x37dc379c (EVT_HTP) <7>[ 57.416178] xe 0000:00:02.0: [drm:intel_display_driver_probe_nogem [xe]] 3 display pipes available. <7>[ 57.419042] xe 0000:00:02.0: [drm:intel_cdclk_read_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 57.419200] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max CD clock rate: 652800 kHz <7>[ 57.419349] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max dotclock rate: 1305600 kHz <7>[ 57.419546] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:204:DDI A/PHY A] Using AUX CH A (VBT) <7>[ 57.419763] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding eDP connector on [ENCODER:204:DDI A/PHY A] <7>[ 57.419984] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel type (VBT): 2 <7>[ 57.420140] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Selected panel type (VBT): 2 <7>[ 57.420282] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] DRRS supported mode is seamless <7>[ 57.420428] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7>[ 57.420566] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT initial LVDS value 300 <7>[ 57.420703] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002 <7>[ 57.420838] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel name: LFP_PanelName <7>[ 57.420996] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Seamless DRRS min refresh rate: 0 Hz <7>[ 57.421132] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7>[ 57.421340] xe 0000:00:02.0: [drm:intel_pps_init [xe]] [ENCODER:204:DDI A/PHY A] initial power sequencer: PPS 0 <7>[ 57.421596] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 57.421720] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 57.421824] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 57.421935] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 57.422056] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 57.422326] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 57.422650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7>[ 57.423966] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 turning VDD on <7>[ 57.424271] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7>[ 57.425832] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 57.426386] xe 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 7.3 SW-rev 0.0 quirks 0x0000 <6>[ 57.426487] xe 0000:00:02.0: [drm] Finished loading DMC firmware i915/xe2lpd_dmc.bin (v2.29) <7>[ 57.426840] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] eDP DPCD: 05 83 85 04 1e <7>[ 57.427448] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] eDP panel supports PSR version 3 <7>[ 57.427781] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] PSR2 supported <7>[ 57.429475] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 57.438554] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 57.438565] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 57.438566] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 57.438567] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 57.438571] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 57.438572] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD monitor <5>[ 57.438578] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 57.438579] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD size 20, SAD count 0 <5>[ 57.438582] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 57.438623] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 57.438624] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 57.438625] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 57.438634] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:205:eDP-1] using preferred EDID fixed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 57.438966] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:205:eDP-1] Performing OUI wait (0 ms) <7>[ 57.439310] xe 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [xe]] [CONNECTOR:205:eDP-1] Detected unsupported HDR backlight interface version 0 <7>[ 57.439461] xe 0000:00:02.0: [drm:intel_panel_init [xe]] [CONNECTOR:205:eDP-1] DRRS type: none <7>[ 57.439615] xe 0000:00:02.0: [drm:cnp_setup_backlight [xe]] [CONNECTOR:205:eDP-1] Using native PCH PWM for backlight control (controller=0) <7>[ 57.439784] xe 0000:00:02.0: [drm:intel_backlight_setup [xe]] [CONNECTOR:205:eDP-1] backlight initialized, enabled, brightness 192000/192000 <7>[ 57.439985] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 57.440110] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 57.440230] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 57.440330] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 57.440418] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 57.440537] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 57.440730] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:213:DDI TC1/PHY TC1] Using AUX CH USBC1 (VBT) <7>[ 57.440911] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 57.441044] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:213:DDI TC1/PHY TC1] <7>[ 57.441431] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:225:DDI TC2/PHY TC2] Using AUX CH USBC2 (VBT) <7>[ 57.441565] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 57.441682] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:225:DDI TC2/PHY TC2] <7>[ 57.441930] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:233:DDI TC3/PHY TC3] Using AUX CH USBC3 (VBT) <7>[ 57.442069] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 57.442194] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:233:DDI TC3/PHY TC3] <7>[ 57.442706] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] hw state readout: enabled <7>[ 57.442829] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:145:pipe B] hw state readout: disabled <7>[ 57.442955] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:202:pipe C] hw state readout: disabled <7>[ 57.443059] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] hw state readout: enabled, pipe A <7>[ 57.443159] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A <7>[ 57.443256] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A <7>[ 57.443345] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A <7>[ 57.443433] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A <7>[ 57.443520] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] hw state readout: disabled, pipe A <7>[ 57.443606] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:90:plane 1B] hw state readout: disabled, pipe B <7>[ 57.443692] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:100:plane 2B] hw state readout: disabled, pipe B <7>[ 57.443777] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:110:plane 3B] hw state readout: disabled, pipe B <7>[ 57.443862] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:120:plane 4B] hw state readout: disabled, pipe B <7>[ 57.443960] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:130:plane 5B] hw state readout: disabled, pipe B <7>[ 57.444053] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:140:cursor B] hw state readout: disabled, pipe B <7>[ 57.444150] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:147:plane 1C] hw state readout: disabled, pipe C <7>[ 57.444247] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:157:plane 2C] hw state readout: disabled, pipe C <7>[ 57.444341] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:167:plane 3C] hw state readout: disabled, pipe C <7>[ 57.444434] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:177:plane 4C] hw state readout: disabled, pipe C <7>[ 57.444520] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:187:plane 5C] hw state readout: disabled, pipe C <7>[ 57.444602] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:197:cursor C] hw state readout: disabled, pipe C <7>[ 57.445389] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7>[ 57.445502] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:204:DDI A/PHY A] hw state readout: enabled, pipe A <7>[ 57.445590] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 57.445675] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:213:DDI TC1/PHY TC1] hw state readout: disabled, pipe A <7>[ 57.445753] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:215:DP-MST A] hw state readout: disabled, pipe A <7>[ 57.445830] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:216:DP-MST B] hw state readout: disabled, pipe B <7>[ 57.445915] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:217:DP-MST C] hw state readout: disabled, pipe C <7>[ 57.445999] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 57.446088] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:225:DDI TC2/PHY TC2] hw state readout: disabled, pipe A <7>[ 57.446174] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:227:DP-MST A] hw state readout: disabled, pipe A <7>[ 57.446262] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:228:DP-MST B] hw state readout: disabled, pipe B <7>[ 57.446343] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:229:DP-MST C] hw state readout: disabled, pipe C <7>[ 57.446425] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 57.446509] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:233:DDI TC3/PHY TC3] hw state readout: disabled, pipe A <7>[ 57.446586] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:235:DP-MST A] hw state readout: disabled, pipe A <7>[ 57.446663] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:236:DP-MST B] hw state readout: disabled, pipe B <7>[ 57.446738] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:237:DP-MST C] hw state readout: disabled, pipe C <7>[ 57.446836] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:205:eDP-1] hw state readout: enabled <7>[ 57.446932] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:214:DP-1] hw state readout: disabled <7>[ 57.447020] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:226:DP-2] hw state readout: disabled <7>[ 57.447103] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:234:DP-3] hw state readout: disabled <7>[ 57.447259] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] min_cdclk 173855 kHz <7>[ 57.447345] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] min_cdclk 0 kHz <7>[ 57.447433] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] min_cdclk 0 kHz <7>[ 57.447520] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] min_cdclk 0 kHz <7>[ 57.447604] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] min_cdclk 0 kHz <7>[ 57.447680] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] min_cdclk 0 kHz <7>[ 57.447756] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] min_cdclk 173855 kHz <7>[ 57.447830] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:90:plane 1B] min_cdclk 0 kHz <7>[ 57.447908] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:100:plane 2B] min_cdclk 0 kHz <7>[ 57.447994] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:110:plane 3B] min_cdclk 0 kHz <7>[ 57.448088] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:120:plane 4B] min_cdclk 0 kHz <7>[ 57.448182] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:130:plane 5B] min_cdclk 0 kHz <7>[ 57.448267] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:140:cursor B] min_cdclk 0 kHz <7>[ 57.448345] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:145:pipe B] min_cdclk 0 kHz <7>[ 57.448417] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:147:plane 1C] min_cdclk 0 kHz <7>[ 57.448487] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:157:plane 2C] min_cdclk 0 kHz <7>[ 57.448560] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:167:plane 3C] min_cdclk 0 kHz <7>[ 57.448636] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:177:plane 4C] min_cdclk 0 kHz <7>[ 57.448713] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:187:plane 5C] min_cdclk 0 kHz <7>[ 57.448789] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:197:cursor C] min_cdclk 0 kHz <7>[ 57.448863] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:202:pipe C] min_cdclk 0 kHz <7>[ 57.449102] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:88:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no <7>[ 57.449210] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:145:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 57.449300] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:202:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 57.449380] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 1390840 num active planes 1 <7>[ 57.449492] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0 <7>[ 57.449605] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0 <7>[ 57.449759] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: enabled, CMTG B: disabled, Transcoder A secondary: yes, Transcoder B secondary: no <7>[ 57.449867] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] Disabling CMTG A <7>[ 57.450152] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [setup_hw_state] <7>[ 57.450288] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 57.450406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7>[ 57.450505] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 57.450602] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 57.450698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 57.450793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 57.450889] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64 <7>[ 57.451018] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 57.451141] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 57.451255] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 57.451353] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7>[ 57.451443] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 57.451531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7>[ 57.451623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 57.451712] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vblank delay: 1, framestart delay: 1, MSA timing delay: 0 set context latency: 1 <7>[ 57.451802] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: yes, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 105 vsync start: 103, vsync end: 96 <7>[ 57.451893] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1801, vmax vblank: 1801, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 57.452016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 57.452138] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 57.452262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 57.452367] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 57.452457] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 57.452545] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 57.452632] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 57.452716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 57.452800] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 57.452885] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 57.453008] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x41eb0, dpll_md: 0xf42110, fp0: 0xf8, fp1: 0x1000000 <7>[ 57.453117] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0 <7>[ 57.453222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 57.453311] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 57.453395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.453476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.453556] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.453636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 57.453716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 57.453795] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.453876] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.453989] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 57.454103] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 57.454216] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:145:pipe B] enable: no [setup_hw_state] <7>[ 57.454310] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:202:pipe C] enable: no [setup_hw_state] <7>[ 57.454676] xe 0000:00:02.0: [drm:skl_get_initial_plane_config [xe]] [CRTC:88:pipe A][PLANE:33:plane 1A] with fb: size=2880x1800@32, offset=fec00000, pitch 11520, size 0x13c6800 <7>[ 57.454777] xe 0000:00:02.0: [drm:intel_plane_disable_noatomic [xe]] Disabling [PLANE:33:plane 1A] on [CRTC:88:pipe A] <6>[ 57.478790] xe 0000:00:02.0: [drm] Tile0: GT0: Using GuC firmware from xe/lnl_guc_70.bin version 70.49.4 <7>[ 57.482739] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003533f7 <7>[ 57.482857] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000000 <7>[ 57.482973] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000000 <7>[ 57.483079] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 57.483184] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d0 <7>[ 57.483285] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 57.483368] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 57.483447] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 57.483522] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 57.483593] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 57.483662] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 57.483729] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 57.483794] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 57.483858] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 57.483939] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 57.484061] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [6144K, 832K) <7>[ 57.494955] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 9ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 57.496264] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 57.496679] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (geometry): 00000000,00000000,0000007f <7>[ 57.496846] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (compute): 00000000,00000000,0000007f <7>[ 57.497015] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU mask per DSS: 000000ff <7>[ 57.497157] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU type: simd16 <7>[ 57.497297] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: L3 bank mask: 00000000,000000ff <6>[ 58.137979] xe 0000:00:02.0: [drm] Tile0: GT0: ccs1 fused off <6>[ 58.137983] xe 0000:00:02.0: [drm] Tile0: GT0: ccs2 fused off <6>[ 58.137984] xe 0000:00:02.0: [drm] Tile0: GT0: ccs3 fused off <7>[ 58.138136] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add rcs0 whitelist to engine <7>[ 58.138267] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 58.138377] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 58.138476] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 58.138607] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs0 whitelist to engine <7>[ 58.138724] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs8 whitelist to engine <7>[ 58.138868] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add ccs0 whitelist to engine <7>[ 58.138986] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 58.139101] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 58.139214] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 58.140642] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying GT save-restore MMIOs <7>[ 58.140739] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x4148] = 0x00000000 <7>[ 58.140839] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x8828] = 0x00800000 <7>[ 58.140940] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb104] = 0x08104440 <7>[ 58.141057] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb108] = 0x30200000 <7>[ 58.141175] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb154] = 0x00020000 <7>[ 58.141285] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb158] = 0x0000007f <7>[ 58.141376] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: flag:0x1 <7>[ 58.141461] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: mocs entries: 16 <7>[ 58.141544] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[0] 0x4000 0xc <7>[ 58.141629] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[1] 0x4004 0x10c <7>[ 58.141713] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[2] 0x4008 0x130 <7>[ 58.141796] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[3] 0x400c 0x13c <7>[ 58.141877] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[4] 0x4010 0x100 <7>[ 58.141970] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[5] 0x4014 0x100 <7>[ 58.142060] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[6] 0x4018 0x100 <7>[ 58.142162] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[7] 0x401c 0x100 <7>[ 58.142270] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[8] 0x4020 0x100 <7>[ 58.142365] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[9] 0x4024 0x100 <7>[ 58.142449] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[10] 0x4028 0x100 <7>[ 58.142530] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[11] 0x402c 0x100 <7>[ 58.142609] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[12] 0x4030 0x100 <7>[ 58.142687] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[13] 0x4034 0x100 <7>[ 58.142764] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[14] 0x4038 0x100 <7>[ 58.142841] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[15] 0x403c 0x100 <7>[ 58.142923] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying rcs0 save-restore MMIOs <7>[ 58.143009] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x2050] = 0x10001000 <7>[ 58.143107] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20c4] = 0x3f7e0306 <7>[ 58.143204] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20d4] = 0xc080c080 <7>[ 58.143298] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d0] = 0x1000dafc <7>[ 58.143382] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d4] = 0x1000db01 <7>[ 58.143463] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d8] = 0x0000db1c <7>[ 58.143544] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe194] = 0x00400040 <7>[ 58.143627] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe48c] = 0x02000200 <7>[ 58.143709] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe49c] = 0x40004000 <7>[ 58.143791] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4c4] = 0x08400840 <7>[ 58.143872] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4f0] = 0x00020002 <7>[ 58.143978] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe530] = 0x00000400 <7>[ 58.144084] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7c8] = 0x00002000 <7>[ 58.144188] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7cc] = 0x00009000 <7>[ 58.144568] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs0 save-restore MMIOs <7>[ 58.144648] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x22050] = 0x10001000 <7>[ 58.144728] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220c4] = 0x3f7e0306 <7>[ 58.144805] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220d4] = 0xc080c080 <7>[ 58.145156] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs8 save-restore MMIOs <7>[ 58.145248] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee050] = 0x10001000 <7>[ 58.145333] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0c4] = 0x3f7e0306 <7>[ 58.145407] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0d4] = 0xc080c080 <7>[ 58.145707] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying ccs0 save-restore MMIOs <7>[ 58.145780] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a050] = 0x10001000 <7>[ 58.145853] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0c4] = 0x3f7e0306 <7>[ 58.145934] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0d4] = 0xc080c080 <7>[ 58.146010] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d0] = 0x1000dafc <7>[ 58.146096] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d4] = 0x1000db01 <7>[ 58.146188] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d8] = 0x0000db1c <7>[ 58.146700] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled <7>[ 58.146833] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003533f7 <7>[ 58.146922] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000800 <7>[ 58.147003] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000014 <7>[ 58.147098] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 58.147189] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d0 <7>[ 58.147276] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 58.147357] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 58.147432] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 58.147505] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 58.147577] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 58.147648] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 58.147718] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 58.147789] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 58.147860] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 58.147961] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT0: using 65535 GuC IDs <7>[ 58.148142] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT0: using 256 doorbells <7>[ 58.149382] xe 0000:00:02.0: [drm:xe_guc_buf_cache_init [xe]] Tile0: GT0: reusable buffer with 2048 dwords at 0xd18000 for xe_guc_init_post_hwconfig [xe] <7>[ 58.152059] xe 0000:00:02.0: [drm:xe_guc_capture_steered_list_init [xe]] Tile0: GT0: capture found 42 ext-regs. <7>[ 58.168446] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT0: Updated ADS capture size 20480 (was 45056) <7>[ 58.179340] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 10ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 58.179697] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 58.180534] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC rcs0 WA job: 4138 dwords <7>[ 58.180661] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x5588] = 0x04000400 <7>[ 58.180750] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6204] = 0x00400040 <7>[ 58.180834] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6208] = 0x00200020 <7>[ 58.180926] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x62a8] = 0x02400240 <7>[ 58.181011] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7010] = 0x40004000 <7>[ 58.181100] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7044] = 0x04200420 <7>[ 58.181184] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x83a8] = 0x20002000 <7>[ 58.181274] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6210] = ~0x18000|0x18000 <7>[ 58.183577] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC bcs0 WA job: 27 dwords <7>[ 58.183743] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x22204] = ~0x7e7e|0x606 <7>[ 58.183835] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <7>[ 58.186014] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC ccs0 WA job: 0 dwords <7>[ 58.186127] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <6>[ 58.190177] xe 0000:00:02.0: [drm] Tile0: GT1: Using GuC firmware from xe/lnl_guc_70.bin version 70.49.4 <7>[ 58.194789] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df43f7 <7>[ 58.194980] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 58.195142] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000000 <7>[ 58.195299] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 58.195451] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e12 <7>[ 58.195595] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 58.195733] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 58.195867] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 58.196037] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 58.196171] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 58.196298] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 58.196421] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 58.196541] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 58.196669] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <6>[ 58.198135] xe 0000:00:02.0: [drm] Tile0: GT1: Using HuC firmware from xe/lnl_huc.bin version 9.4.13 <6>[ 58.200349] xe 0000:00:02.0: [drm] Tile0: GT1: Using GSC firmware from xe/lnl_gsc_1.bin version 104.0.5.1429 <6>[ 58.201395] mei_gsc_proxy 0000:00:16.0-0f73db04-97ab-4125-b893-e904ad0d5464: bound 0000:00:02.0 (ops xe_gsc_proxy_component_ops [xe]) <7>[ 58.201518] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 58.201673] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [5136K, 832K) <7>[ 58.222981] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 19ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 58.223496] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 58.223787] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (geometry): 00000000,00000000,00000000 <7>[ 58.224078] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (compute): 00000000,00000000,00000000 <7>[ 58.224331] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU mask per DSS: 00000000 <7>[ 58.224576] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU type: simd16 <7>[ 58.224819] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: L3 bank mask: 00000000,0000000f <6>[ 58.225112] xe 0000:00:02.0: [drm] Tile0: GT1: vcs1 fused off <6>[ 58.225117] xe 0000:00:02.0: [drm] Tile0: GT1: vcs2 fused off <6>[ 58.225121] xe 0000:00:02.0: [drm] Tile0: GT1: vcs3 fused off <6>[ 58.225124] xe 0000:00:02.0: [drm] Tile0: GT1: vcs4 fused off <6>[ 58.225127] xe 0000:00:02.0: [drm] Tile0: GT1: vcs5 fused off <6>[ 58.225129] xe 0000:00:02.0: [drm] Tile0: GT1: vcs6 fused off <6>[ 58.225132] xe 0000:00:02.0: [drm] Tile0: GT1: vcs7 fused off <6>[ 58.225134] xe 0000:00:02.0: [drm] Tile0: GT1: vecs1 fused off <6>[ 58.225137] xe 0000:00:02.0: [drm] Tile0: GT1: vecs2 fused off <6>[ 58.225139] xe 0000:00:02.0: [drm] Tile0: GT1: vecs3 fused off <7>[ 58.225248] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vcs0 whitelist to engine <7>[ 58.225649] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vecs0 whitelist to engine <7>[ 58.226044] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add gsccs0 whitelist to engine <7>[ 58.228394] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying GT save-restore MMIOs <7>[ 58.228653] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x4148] = 0x00000000 <7>[ 58.228913] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x82a8] = 0x00800000 <7>[ 58.229145] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb604] = 0x08104440 <7>[ 58.229364] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb608] = 0x30200000 <7>[ 58.229583] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb654] = 0x00020000 <7>[ 58.229787] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb658] = 0x0000007f <7>[ 58.230012] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f08] = 0x00000020 <7>[ 58.230200] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f10] = 0x00400000 <7>[ 58.230387] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f1c] = 0x00000008 <7>[ 58.230576] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: flag:0x1 <7>[ 58.230759] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: mocs entries: 16 <7>[ 58.230947] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[0] 0x4000 0xc <7>[ 58.231151] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[1] 0x4004 0x10c <7>[ 58.231339] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[2] 0x4008 0x130 <7>[ 58.231545] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[3] 0x400c 0x13c <7>[ 58.231729] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[4] 0x4010 0x100 <7>[ 58.231889] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[5] 0x4014 0x100 <7>[ 58.232076] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[6] 0x4018 0x100 <7>[ 58.232226] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[7] 0x401c 0x100 <7>[ 58.232371] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[8] 0x4020 0x100 <7>[ 58.232511] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[9] 0x4024 0x100 <7>[ 58.232647] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[10] 0x4028 0x100 <7>[ 58.232779] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[11] 0x402c 0x100 <7>[ 58.232914] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[12] 0x4030 0x100 <7>[ 58.233040] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[13] 0x4034 0x100 <7>[ 58.233159] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[14] 0x4038 0x100 <7>[ 58.233278] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[15] 0x403c 0x100 <7>[ 58.233412] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vcs0 save-restore MMIOs <7>[ 58.233570] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c0050] = 0x10001000 <7>[ 58.233702] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c00d4] = 0xc000c000 <7>[ 58.234254] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vecs0 save-restore MMIOs <7>[ 58.234387] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c8050] = 0x10001000 <7>[ 58.234521] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c80d4] = 0xc000c000 <7>[ 58.235035] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying gsccs0 save-restore MMIOs <7>[ 58.235161] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a050] = 0x10001000 <7>[ 58.235281] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a0d4] = 0xc000c000 <7>[ 58.235946] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled <7>[ 58.236099] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df43f7 <7>[ 58.236206] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 58.236311] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000014 <7>[ 58.236415] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 58.236517] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e12 <7>[ 58.236616] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 58.236711] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 58.236803] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 58.236895] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 58.237008] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 58.237108] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 58.237201] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 58.237284] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 58.237366] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <7>[ 58.237468] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT1: using 65535 GuC IDs <7>[ 58.237587] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT1: using 256 doorbells <7>[ 58.239077] xe 0000:00:02.0: [drm:xe_guc_buf_cache_init [xe]] Tile0: GT1: reusable buffer with 2048 dwords at 0x1982000 for xe_guc_init_post_hwconfig [xe] <7>[ 58.268685] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT1: Updated ADS capture size 24576 (was 45056) <7>[ 58.288929] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 19ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 58.289459] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 58.291036] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vcs0 WA job: 0 dwords <7>[ 58.291364] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 58.295030] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vecs0 WA job: 0 dwords <7>[ 58.295345] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 58.298036] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC gsccs0 WA job: 0 dwords <7>[ 58.298286] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 58.341842] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GuC <7>[ 58.343095] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT0: oa_unit 0, type 0, Engines: rcs0 ccs0 <7>[ 58.343495] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 1, type 2, Engines: <7>[ 58.343897] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 2, type 1, Engines: vcs0 vecs0 <7>[ 58.347276] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 0: start 0x90008 <7>[ 58.347743] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 1: start 0x90108 <7>[ 58.348213] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 2: start 0x90208 <7>[ 58.348650] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 3: start 0x90308 <7>[ 58.349082] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 4: start 0x903c8 <7>[ 58.349470] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:145:pipe B] FQ 0: start 0x98008 <7>[ 58.349819] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:145:pipe B] FQ 1: start 0x98108 <7>[ 58.350221] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:145:pipe B] FQ 2: start 0x98208 <7>[ 58.350558] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:145:pipe B] FQ 3: start 0x98308 <7>[ 58.350890] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:145:pipe B] FQ 4: start 0x983c8 <7>[ 58.351252] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:202:pipe C] FQ 0: start 0x52008 <7>[ 58.351636] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:202:pipe C] FQ 1: start 0x52108 <7>[ 58.352002] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:202:pipe C] FQ 2: start 0x52208 <7>[ 58.352352] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:202:pipe C] FQ 3: start 0x52308 <7>[ 58.352696] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:202:pipe C] FQ 4: start 0x523c8 <7>[ 58.353543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7>[ 58.353935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:88:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7>[ 58.354297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45 <7>[ 58.354713] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:145:pipe B] enable: no [fastset] <7>[ 58.355132] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:202:pipe C] enable: no [fastset] <7>[ 58.356983] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: A) <7>[ 58.357251] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes) <7>[ 58.368583] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:145:pipe B] <7>[ 58.369064] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:202:pipe C] <7>[ 58.378954] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:205:eDP-1] adding connector to sysfs <7>[ 58.381793] xe 0000:00:02.0: [drm:intel_backlight_device_register [xe]] [CONNECTOR:205:eDP-1] backlight device intel_backlight registered <7>[ 58.382011] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:205:eDP-1] Registered panel device 'card0-eDP-1', has fwnode: yes <7>[ 58.382173] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:205:eDP-1] Panel prepare <7>[ 58.382597] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7>[ 58.383763] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:205:eDP-1] generating connector hotplug event <7>[ 58.383826] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:214:DP-1] adding connector to sysfs <7>[ 58.384252] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1 <7>[ 58.384888] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:214:DP-1] generating connector hotplug event <7>[ 58.384971] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:226:DP-2] adding connector to sysfs <7>[ 58.385396] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2 <7>[ 58.386100] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:226:DP-2] generating connector hotplug event <7>[ 58.386137] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:234:DP-3] adding connector to sysfs <7>[ 58.386576] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC3/DDI TC3/PHY TC3 bus for card0-DP-3 <7>[ 58.387457] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:234:DP-3] generating connector hotplug event <6>[ 58.387492] [drm] Initialized xe 1.1.0 for 0000:00:02.0 on minor 0 <7>[ 58.387526] xe 0000:00:02.0: [drm:intel_opregion_resume [xe]] 4 outputs detected <6>[ 58.397394] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6>[ 58.400724] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5 <7>[ 58.401972] xe 0000:00:02.0: [drm:intel_audio_init [xe]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010) <7>[ 58.402133] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480 <7>[ 58.402926] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix <6>[ 58.402935] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <7>[ 58.404550] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:214:DP-1] <7>[ 58.404841] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 58.405203] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:214:DP-1] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 58.405365] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:226:DP-2] <7>[ 58.405546] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 58.405686] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:226:DP-2] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 58.405818] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:234:DP-3] <7>[ 58.405985] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 58.406121] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:234:DP-3] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 58.406252] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <6>[ 58.406565] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [xe]) <7>[ 58.407646] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [PLANE:33:plane 1A] no fb, skipping <7>[ 58.407701] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010 <7>[ 58.407780] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:145:pipe B] not active, skipping <7>[ 58.407904] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:202:pipe C] not active, skipping <7>[ 58.408018] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] no active fbs found, not using BIOS config <7>[ 58.408476] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 58.409671] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:205:eDP-1] <7>[ 58.409680] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:205:eDP-1] <7>[ 58.410456] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 58.410844] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 58.411110] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 58.411227] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 58.411549] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 58.411559] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 58.411562] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 58.411563] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 58.411567] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 58.411568] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD monitor <5>[ 58.411577] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 58.411579] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD size 20, SAD count 0 <5>[ 58.411582] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 58.411626] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] VRR capable: yes <7>[ 58.411745] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 58.411847] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7>[ 58.412177] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9b01 <7>[ 58.412822] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:205:eDP-1] status updated from unknown to connected <7>[ 58.413265] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7>[ 58.413419] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL <7>[ 58.413430] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled <5>[ 58.414052] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 58.414055] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 58.414056] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 58.414087] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:205:eDP-1] probed modes: <7>[ 58.414093] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 58.414098] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:214:DP-1] <7>[ 58.414103] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:214:DP-1] <7>[ 58.414337] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:214:DP-1] disconnected <7>[ 58.414343] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-2] <7>[ 58.414346] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:226:DP-2] <7>[ 58.414515] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-2] disconnected <7>[ 58.414518] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:234:DP-3] <7>[ 58.414521] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:234:DP-3] <7>[ 58.414681] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:234:DP-3] disconnected <7>[ 58.414683] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:205:eDP-1] enabled? yes <7>[ 58.414686] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:214:DP-1] enabled? no <7>[ 58.414688] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:226:DP-2] enabled? no <7>[ 58.414690] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:234:DP-3] enabled? no <7>[ 58.414789] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 58.414810] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:205:eDP-1] found preferred mode: 2880x1800 <7>[ 58.414813] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7>[ 58.414824] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 58.414905] xe 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7>[ 58.414913] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] no BIOS fb, allocating a new one <7>[ 58.422732] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] allocated 2880x1800 fb: 0x01da3000 <6>[ 58.425174] fbcon: xedrmfb (fb0) is primary device <7>[ 58.430246] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:205:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7>[ 58.430586] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:204:DDI A/PHY A][CRTC:88:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7>[ 58.430838] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7>[ 58.431122] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7>[ 58.431356] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:204:DDI A/PHY A] [CRTC:88:pipe A] <7>[ 58.431587] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 8102230/8388608 link 675185/524288, found tu 64, data 6329869/8388608 link 421991/524288) <7>[ 58.431805] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dpll_hw_state.cx0pll C10 <7>[ 58.432021] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected: <7>[ 58.432219] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: yes, <7>[ 58.432436] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] quot: 40960, rem: 0, den: 1, <7>[ 58.432638] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 140, tx_clk_div: 1. <7>[ 58.432835] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 58.433044] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 58.433243] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0 <7>[ 58.433436] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 58.433620] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 58.433803] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 58.434004] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23 <7>[ 58.434186] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found: <7>[ 58.434375] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: no, <7>[ 58.434555] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 225, tx_clk_div: 1. <7>[ 58.434731] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 58.434917] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 58.435090] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7>[ 58.435261] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 58.435429] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 58.435599] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 58.435772] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7>[ 58.435980] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30) <7>[ 58.436182] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in port_clock (expected 270000, found 432000) <7>[ 58.436369] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0) <7>[ 58.436547] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] fastset requirement not met, forcing full modeset <7>[ 58.436810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7>[ 58.437033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm <7>[ 58.437213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7>[ 58.437366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7>[ 58.437509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <7>[ 58.437654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 58.437792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.437939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.438077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.438208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 58.438336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.438466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.438596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.438726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 58.438860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 58.439404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.439795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 58.439933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.440060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.440184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 58.440354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:88:pipe A] data rate 1390840 num active planes 1 <7>[ 58.440569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7>[ 58.440759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7>[ 58.440996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 58.441179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 58.441349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7>[ 58.441644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [modeset] <7>[ 58.441841] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 58.442034] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7>[ 58.442201] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 58.442358] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 58.442513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 58.442671] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 58.442826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7>[ 58.442991] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 58.443145] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 58.443298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 58.443453] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7>[ 58.443609] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 58.443769] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7>[ 58.443936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7>[ 58.444089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7>[ 58.444232] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7>[ 58.444376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7>[ 58.444521] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7>[ 58.444666] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7>[ 58.444816] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 58.444975] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vblank delay: 0, framestart delay: 1, MSA timing delay: 0 set context latency: 0 <7>[ 58.445122] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 37 vsync start: 103, vsync end: 97 <7>[ 58.445269] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1869, vmax vblank: 1869, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 58.445416] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 58.445563] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 58.445709] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 58.445854] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 58.446016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 58.446186] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 58.446342] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 58.446499] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 58.446653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 58.446799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 58.446983] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x69780, dpll_md: 0x42110, fp0: 0x1a2, fp1: 0x1000000 <7>[ 58.447130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7>[ 58.447274] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 58.447415] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 58.447554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.447696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.447836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.447988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 58.448132] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 58.448272] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.448413] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.448551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 58.448688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <6>[ 58.448761] xe 0000:00:02.0: [drm] Tile0: GT1: found GSC cv104.1.0 <7>[ 58.448827] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:206] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7>[ 58.448978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7>[ 58.449122] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0 <7>[ 58.449268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no <7>[ 58.449410] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no <7>[ 58.449554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no <7>[ 58.449687] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no <7>[ 58.449718] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC FW async load completed <7>[ 58.449818] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no <7>[ 58.452790] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM <7>[ 58.452971] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]] <7>[ 58.461060] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 58.461294] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 58.461415] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 58.461530] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 58.461636] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 58.461736] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 58.461834] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 58.461943] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 58.462068] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 58.462189] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 58.462293] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 58.462384] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 58.462475] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 58.462568] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 58.462658] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 58.462746] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 58.462834] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 58.462927] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 58.463045] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 58.463159] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 58.463261] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 58.463348] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 58.463434] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 58.463521] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 58.463608] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 58.463693] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 58.463779] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 58.463863] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 58.463973] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 58.464083] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 58.464191] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 58.464287] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 58.464380] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 58.464473] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 58.464566] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 58.464655] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <6>[ 58.472168] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input6 <7>[ 58.473184] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GSC <6>[ 58.475848] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input7 <6>[ 58.477279] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input8 <6>[ 58.479438] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input9 <7>[ 58.656124] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:205:eDP-1] set backlight PWM = 0 <7>[ 58.657297] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A <7>[ 58.677534] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 turn panel power off <7>[ 58.677859] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 wait for panel power off time <7>[ 58.678203] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 58.678584] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:204:DDI A/PHY A] - short <7>[ 58.679127] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7>[ 58.729790] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 58.730354] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A <7>[ 58.730321] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:204:DDI A/PHY A] <7>[ 58.730776] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 58.731126] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:204:DDI A/PHY A] - short <7>[ 58.731849] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0xffff0072 0x1341b072) <7>[ 58.731844] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:204:DDI A/PHY A] <7>[ 58.732475] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:204:DDI A/PHY A] <7>[ 58.732760] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:213:DDI TC1/PHY TC1] <7>[ 58.733058] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:215:DP-MST A] <7>[ 58.733332] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:216:DP-MST B] <7>[ 58.733616] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:217:DP-MST C] <7>[ 58.733861] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:225:DDI TC2/PHY TC2] <7>[ 58.734126] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:227:DP-MST A] <7>[ 58.734426] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:228:DP-MST B] <7>[ 58.734683] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:229:DP-MST C] <7>[ 58.734954] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:233:DDI TC3/PHY TC3] <7>[ 58.735202] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:235:DP-MST A] <7>[ 58.735441] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:236:DP-MST B] <7>[ 58.735712] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:237:DP-MST C] <7>[ 58.736020] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7>[ 58.737679] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 turn panel power on <7>[ 58.738039] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 wait for panel power cycle (493 ms remaining) <7>[ 58.767218] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 58.767606] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:204:DDI A/PHY A] - long <7>[ 58.767972] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10 <7>[ 58.768330] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:204:DDI A/PHY A] <7>[ 58.898820] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC proxy init completed <7>[ 59.240152] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060 <7>[ 59.300309] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 59.300690] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 wait for panel power on <7>[ 59.301073] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7>[ 59.337344] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 59.337741] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:204:DDI A/PHY A] - long <7>[ 59.338120] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20 <7>[ 59.338531] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:204:DDI A/PHY A] <7>[ 59.472633] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 59.472642] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 59.472761] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 59.512547] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 59.514618] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 turning VDD on <7>[ 59.514969] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7>[ 59.517061] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 59.518294] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Reloading eDP link rates <7>[ 59.519180] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05 <7>[ 59.520275] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7>[ 59.521402] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7>[ 59.522361] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Clock recovery OK <7>[ 59.522683] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Using DP training pattern TPS4 <7>[ 59.524046] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7>[ 59.524383] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:205:eDP-1][ENCODER:204:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4 <7>[ 59.525156] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A <7>[ 59.525585] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]] <7>[ 59.525889] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A <7>[ 59.526270] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:205:eDP-1] set backlight PWM = 192000 <7>[ 59.543162] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7>[ 59.545104] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:205:eDP-1] <7>[ 59.545471] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:88:pipe A] <7>[ 59.546758] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp <7>[ 59.548036] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072) <7>[ 59.548967] xe 0000:00:02.0: [drm:intel_backlight_device_update_status [xe]] updating intel_backlight, brightness=9600/192000 <6>[ 59.549556] Console: switching <7>[ 59.549388] xe 0000:00:02.0: [drm:intel_panel_actually_set_backlight [xe]] [CONNECTOR:205:eDP-1] set backlight level = 13892 <4>[ 59.549559] to colour frame buffer device 180x56 <6>[ 59.580924] xe 0000:00:02.0: [drm] fb0: xedrmfb frame buffer device <7>[ 59.587138] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display version: 20 <7>[ 59.587594] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display stepping: B0 <7>[ 59.588013] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: cursor_needs_physical: no <7>[ 59.588380] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_crawl: yes <7>[ 59.588703] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_squash: yes <7>[ 59.589065] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ddi: yes <7>[ 59.589364] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dp_mst: yes <7>[ 59.589656] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsb: yes <7>[ 59.589959] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_fpga_dbg: yes <7>[ 59.590292] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_gmch: no <7>[ 59.590567] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hotplug: yes <7>[ 59.590838] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hti: no <7>[ 59.591136] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ipc: yes <7>[ 59.591454] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_overlay: no <7>[ 59.591716] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr: yes <7>[ 59.592003] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr_hw_tracking: no <7>[ 59.592294] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: overlay_needs_physical: no <7>[ 59.592586] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: supports_tv: no <7>[ 59.592853] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hdcp: yes <7>[ 59.593149] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dmc: yes <7>[ 59.593406] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsc: yes <7>[ 59.593645] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: rawclk rate: 38400 kHz <7>[ 59.595179] [drm:intel_dsm_detect.isra.0 [xe]] no _DSM method for intel device <7>[ 59.595516] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC <7>[ 59.595949] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D <7>[ 59.596329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C <7>[ 59.596739] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B <7>[ 59.597112] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 59.597440] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 59.598241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 59.603276] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] d3cold: capable=no <7>[ 59.611432] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 59.612392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 59.626679] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7>[ 59.626706] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 59.627334] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:205:eDP-1] <7>[ 59.627356] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:205:eDP-1] <7>[ 59.628272] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 59.628804] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 59.629127] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 59.629386] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 59.629829] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 59.629841] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 59.629844] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 59.629846] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 59.629853] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 59.629856] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD monitor <5>[ 59.629873] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 59.629876] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:205:eDP-1] ELD size 20, SAD count 0 <5>[ 59.629882] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 59.629926] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] VRR capable: yes <7>[ 59.630169] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 59.630408] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:205:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5>[ 59.631297] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 59.631304] [drm] DisplayID checksum invalid, remainder is 248 <5>[ 59.631308] [drm] DisplayID checksum invalid, remainder is 248 <7>[ 59.631382] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:205:eDP-1] probed modes: <7>[ 59.631535] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 59.631547] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:214:DP-1] <7>[ 59.631557] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:214:DP-1] <7>[ 59.631935] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 59.632279] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 59.632608] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 59.632997] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 59.633311] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:214:DP-1] disconnected <7>[ 59.633325] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-2] <7>[ 59.633333] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:226:DP-2] <7>[ 59.633661] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 59.633914] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-2] disconnected <7>[ 59.633922] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:234:DP-3] <7>[ 59.633929] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:234:DP-3] <7>[ 59.634220] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 59.634497] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:234:DP-3] disconnected <7>[ 59.634503] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:205:eDP-1] enabled? yes <7>[ 59.634509] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:214:DP-1] enabled? no <7>[ 59.634514] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:226:DP-2] enabled? no <7>[ 59.634518] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:234:DP-3] enabled? no <7>[ 59.635555] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 59.635607] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:205:eDP-1] found preferred mode: 2880x1800 <7>[ 59.635614] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config <7>[ 59.635694] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 59.635979] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7>[ 59.642452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 59.643465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 59.660782] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7>[ 59.661393] [IGT] xe_module_load: finished subtest load, SUCCESS <7>[ 59.662865] [IGT] xe_module_load: exiting, ret=0 <7>[ 59.731633] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2 <7>[ 59.736966] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 59.737342] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 59.738337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 60.689107] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 60.689121] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 60.689105] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 62.161435] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 turning VDD off <7>[ 62.161808] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:204:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067