Result:
i915_display_info1 igt_runner1 results1.json results1-xe-load.json guc_logs1.tar i915_display_info_post_exec1 boot1 dmesg1
| Detail | Value |
|---|---|
| Duration | 1.73 seconds |
| Hostname |
shard-lnl-3 |
| Igt-Version |
IGT-Version: 2.3-g611f1cac6 (x86_64) (Linux: 7.0.0-rc3-lgci-xe-xe-4711-721db23a9c232926f-debug+ x86_64) |
| Out |
Starting dynamic subtest: pipe-C Trying on eDP-1 Dynamic subtest pipe-C: SUCCESS (1.733s) Subtest plane-upscale-20x20-with-modifiers: SUCCESS (3.799s) |
| Err |
Starting dynamic subtest: pipe-C Dynamic subtest pipe-C: SUCCESS (1.733s) Subtest plane-upscale-20x20-with-modifiers: SUCCESS (3.799s) |
| Dmesg |
<6> [112.405987] [IGT] kms_plane_scaling: starting dynamic subtest pipe-C
<7> [112.409760] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [112.411627] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [112.411997] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:388:pipe C] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [112.412317] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [112.412603] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR2 not supported in transcoder C
<7> [112.412842] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:388:pipe C] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [112.413133] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:388:pipe C]
<7> [112.413507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.enable (expected yes, found no)
<7> [112.413832] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.active (expected yes, found no)
<7> [112.414107] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in cpu_transcoder (expected 1, found -1)
<7> [112.414399] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in lane_count (expected 4, found 0)
<7> [112.414722] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [112.414996] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [112.415275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [112.415609] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [112.415865] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [112.416108] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [112.416423] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [112.416656] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [112.416875] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [112.417084] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [112.417410] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [112.417609] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [112.417807] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [112.417992] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [112.418170] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [112.418406] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [112.418594] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [112.418762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [112.418955] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [112.419119] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [112.419285] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [112.419443] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [112.419596] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [112.419741] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [112.419898] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [112.420037] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [112.420173] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [112.420326] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [112.420468] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [112.420603] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [112.420735] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [112.420862] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [112.420987] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [112.421110] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:269:pipe B] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [112.421230] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:269:pipe B] fastset requirement not met, forcing full modeset
<7> [112.421381] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.enable (expected no, found yes)
<7> [112.421502] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.active (expected no, found yes)
<7> [112.421617] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in cpu_transcoder (expected -1, found 2)
<7> [112.421728] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in lane_count (expected 0, found 4)
<7> [112.421838] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [112.421944] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [112.422049] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [112.422150] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [112.422258] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [112.422275] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [112.422361] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [112.422418] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [112.422459] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [112.422536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [112.422556] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [112.422650] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [112.422743] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [112.422834] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [112.422924] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [112.423013] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [112.423100] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [112.423187] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [112.423284] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [112.423374] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [112.423461] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [112.423546] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [112.423630] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [112.423715] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [112.423798] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [112.423876] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [112.423953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [112.424028] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [112.424102] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [112.424174] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [112.424251] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [112.424326] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [112.424401] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [112.424474] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in dpll_hw_state
<7> [112.424547] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [112.424617] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [112.424684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state:
<7> [112.424751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [112.424818] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [112.424885] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [112.424953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [112.425020] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [112.425086] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [112.425153] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [112.425222] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [112.425316] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [112.425407] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [112.425496] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [112.425568] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [112.425636] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [112.425705] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [112.425773] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [112.425841] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [112.425910] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: fracen: no,
<7> [112.425978] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [112.426045] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [112.426112] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [112.426180] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [112.426252] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [112.426325] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [112.426398] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [112.426471] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [112.426544] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [112.426610] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [112.426677] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [112.426744] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [112.426810] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:388:pipe C] fastset requirement not met, forcing full modeset
<7> [112.426878] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:269:pipe B] releasing DPLL 0
<7> [112.426957] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: staged scaling request for 20x20->2880x1800 scaler_users = 0x1000
<7> [112.427042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0xd (total dbuf slices 0xf), mbus joined? yes->no
<7> [112.427106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:269:pipe B] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x2 -> 0x4
<7> [112.427170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:388:pipe C] dbuf slices 0x0 -> 0xc, ddb (0 - 0) -> (0 - 2048), active pipes 0x2 -> 0x4
<7> [112.427238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:263:cursor B] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [112.427302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [112.427360] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:382:cursor C] ddb ( 0 - 0) -> (2003 - 2048), size 0 -> 45
<7> [112.427417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [112.427474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [112.427530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [112.427582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [112.427643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [112.427724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [112.427802] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [112.427880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [112.427957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [112.428034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [112.428110] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:269:pipe B] min cdclk: 173855 kHz -> 0 kHz
<7> [112.428188] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:388:pipe C] min cdclk: 0 kHz -> 173855 kHz
<7> [112.428301] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:388:pipe C] allocated DPLL 0
<7> [112.428394] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:388:pipe C] reserving DPLL 0
<7> [112.428503] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:272
<7> [112.428579] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:269:pipe B] enable: no [modeset]
<7> [112.428672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:153:plane 1B] fb: [NOFB], visible: no
<7> [112.428750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:183:plane 2B] fb: [NOFB], visible: no
<7> [112.428826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:213:plane 3B] fb: [NOFB], visible: no
<7> [112.428902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:243:plane 4B] fb: [NOFB], visible: no
<7> [112.428977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:253:plane 5B] fb: [NOFB], visible: no
<7> [112.429051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:263:cursor B] fb: [NOFB], visible: no
<7> [112.429125] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:388:pipe C] enable: yes [modeset]
<7> [112.429199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [112.429285] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: C, pipe bpp: 30, dithering: 0
<7> [112.429368] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [112.429448] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [112.429529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [112.429603] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [112.429676] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [112.429748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [112.429819] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [112.429891] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [112.429962] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [112.430033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [112.430104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [112.430175] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8
<7> [112.430251] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [112.430323] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [112.430396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [112.430470] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [112.430544] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [112.430616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [112.430688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [112.430759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [112.430830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [112.430901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [112.430972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [112.431044] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [112.431115] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [112.431187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [112.431266] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [112.431338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [112.431410] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [112.431479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x1000, scaler_id: -1, scaling_filter: 0
<7> [112.431549] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [112.431619] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [112.431688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [112.431757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [112.431826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [112.431895] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [112.431964] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [112.432032] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [112.432101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [112.432170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [112.432243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [112.432314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [112.432383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [112.432452] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [112.432520] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [112.432588] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.432657] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.432725] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.432793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [112.432861] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [112.432930] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.433002] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.433073] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [112.433144] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [112.433215] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [112.433302] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:272:plane 1C] fb: [FB:432] 20x20 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [112.433380] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: 0, scaling_filter: 0
<7> [112.433457] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 20.000000x20.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [112.433534] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:302:plane 2C] fb: [NOFB], visible: no
<7> [112.433610] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:332:plane 3C] fb: [NOFB], visible: no
<7> [112.433686] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:362:plane 4C] fb: [NOFB], visible: no
<7> [112.433761] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:372:plane 5C] fb: [NOFB], visible: no
<7> [112.433835] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:382:cursor C] fb: [NOFB], visible: no
<7> [112.434000] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [112.434101] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [112.434253] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C
<7> [112.434398] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x4 (CLKGATE_DIS_DSSDSC=0x82000000)
<7> [112.434576] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [112.434663] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [112.637545] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [112.638018] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [112.658711] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [112.659080] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [112.659144] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [112.659474] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [112.659728] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [112.711949] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [112.712590] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [112.719275] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [112.719619] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:269:pipe B]
<7> [112.719651] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [112.719989] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [112.720974] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [112.721317] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [112.721673] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [112.721900] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [112.722108] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [112.722332] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [112.722521] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [112.722705] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [112.722912] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [112.723090] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [112.723297] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [112.723523] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [112.723708] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [112.723891] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [112.724072] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [112.724268] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:401:DP-1]
<7> [112.724464] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:413:DP-2]
<7> [112.724661] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:421:DP-3]
<7> [112.724955] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [112.725154] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [112.725440] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [112.727012] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x4, on? 0) for [CRTC:388:pipe C]
<7> [112.727311] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [112.729598] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [112.729837] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (490 ms remaining)
<7> [112.750175] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [112.750563] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [112.750886] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [112.751352] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [113.221525] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [113.262322] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [113.262684] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [113.263017] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [113.299742] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [113.300305] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [113.300779] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [113.301370] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [113.475928] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [113.476345] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [113.476615] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [113.478670] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [113.480156] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [113.480910] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [113.481969] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [113.483259] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [113.484319] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [113.484641] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [113.486236] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [113.486850] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [113.487836] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe C
<7> [113.488509] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [113.488961] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe C
<7> [113.489493] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 192000
<7> [113.491196] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 20480 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.491600] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:272:plane 1C]
<7> [113.505257] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xd
<7> [113.505927] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [113.506454] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x2 (CLKGATE_DIS_DSSDSC=0x8a000000)
<7> [113.507006] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:269:pipe B]
<7> [113.507487] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.509003] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [113.509472] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:388:pipe C]
<7> [113.513844] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe C
<7> [113.514335] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.514463] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:272:plane 1C] because [FB:432] is removed
<7> [113.514575] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.514930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.515225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.515487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.515718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.515944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.516229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.516593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.516927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.517260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.517574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.517862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.518822] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.521884] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:272:plane 1C]
<7> [113.540100] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.540652] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: staged scaling request for 20x20->2880x1800 scaler_users = 0x1000
<7> [113.541277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.541672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.542019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.542372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.542699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.543089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.543696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.544241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.544749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.545212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.545655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.546211] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:272
<7> [113.548351] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 163840 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.548645] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:272:plane 1C]
<7> [113.555283] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.557202] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.557346] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:272:plane 1C] because [FB:432] is removed
<7> [113.557456] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.557835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.558096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.558398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.558657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.558900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.559211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.559621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.559993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.560383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.560737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.561074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.562031] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.571886] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:272:plane 1C]
<7> [113.589999] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.590478] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: staged scaling request for 20x20->2880x1800 scaler_users = 0x1000
<7> [113.591024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.591444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.591791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [113.592117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [113.592449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [113.592824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.593408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.593924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.594457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.594963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.595482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.596104] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:272
<7> [113.598383] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 40960 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.598711] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:272:plane 1C]
<7> [113.605254] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.606973] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.607096] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:272:plane 1C] because [FB:432] is removed
<7> [113.607265] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.12: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.607634] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:272:plane 1C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.607869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.608075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.608308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.608518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:272:plane 1C] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.608770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.609096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.609432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.609730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.610016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.610296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.611111] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.621874] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:272:plane 1C]
<7> [113.639785] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.640404] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: staged scaling request for 20x20->2880x1800 scaler_users = 0x2000
<7> [113.640962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.641379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.641724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.642046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.642388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.642776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.643336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.643858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.644433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.644947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.645490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.646073] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:302
<7> [113.648176] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 20480 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.648515] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:302:plane 2C]
<7> [113.655273] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.657110] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.657285] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:302:plane 2C] because [FB:432] is removed
<7> [113.657389] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.657751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.658015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.658324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.658597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.658840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.659157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.659575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.659954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.660340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.660687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.661019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.662005] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.671868] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:302:plane 2C]
<7> [113.689906] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.690380] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: staged scaling request for 20x20->2880x1800 scaler_users = 0x2000
<7> [113.690914] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.691322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.691655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.691970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.692296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.692673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.693235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.693752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.694279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.694789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.695311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.695952] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:302
<7> [113.698225] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 163840 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.698548] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:302:plane 2C]
<7> [113.705239] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.706990] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.707167] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:302:plane 2C] because [FB:432] is removed
<7> [113.707264] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.707628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.707864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.708091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.708345] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.708551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.708800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.709154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.709470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.709766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.710059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.710359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.711374] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.721864] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:302:plane 2C]
<7> [113.739948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.740471] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: staged scaling request for 20x20->2880x1800 scaler_users = 0x2000
<7> [113.741048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.741485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.741830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [113.742175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [113.742493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [113.742873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.743431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.743952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.744480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.744930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.745391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.745969] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:302
<7> [113.748396] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 40960 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.748730] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:302:plane 2C]
<7> [113.755255] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.757042] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.757232] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:302:plane 2C] because [FB:432] is removed
<7> [113.757329] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.13: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.757687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:302:plane 2C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.757926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.758178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.758405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.758621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:302:plane 2C] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.758860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.759244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.759584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.759895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.760203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.760492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.761253] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.771851] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:302:plane 2C]
<7> [113.789749] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.790288] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: staged scaling request for 20x20->2880x1800 scaler_users = 0x4000
<7> [113.790770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.791155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.791475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.791751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.792022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.792361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.792826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.793291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.793738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.794224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.794670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.795237] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:332
<7> [113.796986] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 20480 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.797336] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:332:plane 3C]
<7> [113.805216] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.806765] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.806883] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:332:plane 3C] because [FB:432] is removed
<7> [113.806957] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.807358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.807619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.807843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.808049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.808293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.808533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.808860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.809193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.809508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.809819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.810138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.810972] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.821836] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:332:plane 3C]
<7> [113.839638] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.840149] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: staged scaling request for 20x20->2880x1800 scaler_users = 0x4000
<7> [113.840606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.840928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.841254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.841545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.841819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.842170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.842645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.843134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.843586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.844032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.844507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.845061] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:332
<7> [113.847214] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 163840 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.847567] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:332:plane 3C]
<7> [113.855233] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.856842] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.856949] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:332:plane 3C] because [FB:432] is removed
<7> [113.857023] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.857425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.857685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.857932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.858205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.858446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.858731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.859172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.859578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.859949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.860323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.860663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.861546] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.871826] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:332:plane 3C]
<7> [113.889672] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.890021] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: staged scaling request for 20x20->2880x1800 scaler_users = 0x4000
<7> [113.890526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.890864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.891218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [113.891477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [113.891723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [113.892021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.892600] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: staged scaling request for 20x20->2880x1800 scaler_users = 0x4000
<7> [113.892896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.893162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.893403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [113.893647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [113.893889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [113.894159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.894573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.894983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.895407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.895803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.896178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.896629] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:332
<7> [113.898322] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 40960 bytes of contiguous stolen space for FBC, limit: 1
<7> [113.898575] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:332:plane 3C]
<7> [113.905202] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.906536] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.906630] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:332:plane 3C] because [FB:432] is removed
<7> [113.906693] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.14: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.907001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:332:plane 3C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.907274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.907501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.907680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.907830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:332:plane 3C] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.907998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.908288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.908528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.908754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.908974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.909192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.909774] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.921822] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:332:plane 3C]
<7> [113.939466] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.939917] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: staged scaling request for 20x20->2880x1800 scaler_users = 0x8000
<7> [113.940384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.940685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.940954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.941244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.941502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.941806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.942258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.942675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.943082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.943511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.943913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.944455] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:362
<7> [113.955214] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.956843] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.956949] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:362:plane 4C] because [FB:432] is removed
<7> [113.957031] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.957411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.957676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.957927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.958203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.958447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.958732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.959164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.959539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.959903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.960254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.960581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.962027] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [113.972886] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [113.973271] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: staged scaling request for 20x20->2880x1800 scaler_users = 0x8000
<7> [113.973703] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [113.974002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [113.974314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [113.974575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [113.974824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [113.975133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [113.975559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [113.975937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [113.976304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.976643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [113.976976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [113.977398] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:362
<7> [113.988506] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [113.989982] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [113.990072] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:362:plane 4C] because [FB:432] is removed
<7> [113.990168] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: Staged freeing scaler id 0 scaler_users = 0x0
<7> [113.990448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [113.990662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.990866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.991072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.991280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.991504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [113.991827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.992145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.992435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.992707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.992972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.993662] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [114.006032] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [114.006416] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: staged scaling request for 20x20->2880x1800 scaler_users = 0x8000
<7> [114.006798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [114.007066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [114.007373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [114.007623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [114.007865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [114.008192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [114.008592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [114.008954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [114.009323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.009643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.009956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [114.010391] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:362
<7> [114.021880] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [114.023585] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [114.023726] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:362:plane 4C] because [FB:432] is removed
<7> [114.023834] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.15: Staged freeing scaler id 0 scaler_users = 0x0
<7> [114.024319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:362:plane 4C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [114.024602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [114.024784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.024951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.025148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:362:plane 4C] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.025357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [114.025644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [114.025897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [114.026149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.026392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.026624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [114.027363] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [114.039412] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [114.039783] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: staged scaling request for 20x20->2880x1800 scaler_users = 0x10000
<7> [114.040224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [114.040492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [114.040728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [114.040929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [114.041143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [114.041398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [114.041734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [114.042030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [114.042355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.042632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.042899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [114.043269] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:372
<7> [114.055172] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [114.056887] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [114.057033] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:372:plane 5C] because [FB:432] is removed
<7> [114.057188] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: Staged freeing scaler id 0 scaler_users = 0x0
<7> [114.057608] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [114.057831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [114.058043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.058281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.058491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.058721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [114.059050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [114.059398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [114.059704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.059987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.060291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [114.061242] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [114.072816] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [114.073256] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: staged scaling request for 20x20->2880x1800 scaler_users = 0x10000
<7> [114.073721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [114.074008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [114.074326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [114.074585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [114.074820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [114.075148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [114.075584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [114.076005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [114.076463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.076880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.077364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [114.077948] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:372
<7> [114.088537] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [114.090408] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [114.090538] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:372:plane 5C] because [FB:432] is removed
<7> [114.090638] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: Staged freeing scaler id 0 scaler_users = 0x0
<7> [114.091038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [114.091381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [114.091661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.091934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.092222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.092552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [114.093030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [114.093508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [114.093965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.094429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.094835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [114.095932] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [114.106272] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [114.106627] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: staged scaling request for 20x20->2880x1800 scaler_users = 0x10000
<7> [114.107121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 0) -> ( 0 - 2003), size 0 -> 2003
<7> [114.107462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [114.107744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [114.107999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [114.108271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [114.108586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 1390840 num active planes 1
<7> [114.108977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [114.109365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [114.109715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.110037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.110366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [114.110767] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:388:pipe C] attached scaler id 2.0 to PLANE:372
<7> [114.121834] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [114.123537] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [114.123670] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:372:plane 5C] because [FB:432] is removed
<7> [114.123764] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:388:pipe C] scaler_user index 2.16: Staged freeing scaler id 0 scaler_users = 0x0
<7> [114.124200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:372:plane 5C] ddb ( 0 - 2003) -> ( 0 - 0), size 2003 -> 0
<7> [114.124488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [114.124704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.124911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.125136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:372:plane 5C] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [114.125374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:388:pipe C] data rate 0 num active planes 0
<7> [114.125704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [114.126020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [114.126332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.126630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [114.126905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [114.127748] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<6> [114.139290] [IGT] kms_plane_scaling: finished subtest pipe-C, SUCCESS
<6> [114.140441] [IGT] kms_plane_scaling: finished subtest plane-upscale-20x20-with-modifiers, SUCCESS
<7> [114.143712] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [114.146634] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [114.147337] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [114.147791] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [114.148267] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [114.148717] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [114.149121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [114.149488] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [114.149816] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [114.150162] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [114.150461] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [114.150762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [114.151042] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [114.151439] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [114.151708] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [114.151959] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [114.152217] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [114.152461] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [114.152695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [114.152928] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [114.153157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [114.153375] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [114.153635] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [114.154016] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [114.154417] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [114.154720] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [114.155001] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [114.155556] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [114.155762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [114.155937] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [114.156128] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [114.156312] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [114.156483] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [114.156647] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [114.156800] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [114.156949] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [114.157107] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [114.157266] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [114.157414] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [114.157567] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [114.157719] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [114.157853] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [114.157979] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [114.158118] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [114.158251] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [114.158381] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.enable (expected yes, found no)
<7> [114.158511] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.active (expected yes, found no)
<7> [114.158635] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in cpu_transcoder (expected 2, found -1)
<7> [114.158754] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in lane_count (expected 4, found 0)
<7> [114.158865] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [114.158974] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [114.159092] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [114.159203] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [114.159314] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [114.159424] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [114.159535] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [114.159649] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [114.159759] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [114.159864] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [114.159969] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [114.160094] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [114.160203] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [114.160314] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [114.160425] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [114.160534] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [114.160645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [114.160751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [114.160857] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [114.160962] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [114.161078] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [114.161194] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [114.161309] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [114.161419] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [114.161533] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [114.161644] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [114.161750] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [114.161855] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [114.161960] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [114.162080] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [114.162195] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [114.162307] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [114.162419] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [114.162530] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:388:pipe C] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [114.162641] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:388:pipe C] fastset requirement not met, forcing full modeset
<7> [114.162752] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:388:pipe C] releasing DPLL 0
<7> [114.162980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xd -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [114.163112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x4 -> 0x1
<7> [114.163202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:388:pipe C] dbuf slices 0xc -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x4 -> 0x1
<7> [114.163294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [114.163370] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [114.163450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [114.163523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [114.163594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [114.163665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [114.163737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:382:cursor C] ddb (2003 - 2048) -> ( 0 - 0), size 45 -> 0
<7> [114.163839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [114.163972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [114.164129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [114.164255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.164382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [114.164505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [114.164622] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [114.164738] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:388:pipe C] min cdclk: 173855 kHz -> 0 kHz
<7> [114.164931] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [114.165050] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [114.165191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [114.165326] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [114.165450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [114.165569] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [114.165680] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [114.165792] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [114.165902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [114.166013] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [114.166140] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [114.166259] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [114.166376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [114.166497] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [114.166614] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [114.166723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [114.166834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [114.166945] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [114.167056] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [114.167183] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [114.167304] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [114.167420] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [114.167535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [114.167645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [114.167755] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [114.167866] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [114.167979] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [114.168115] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [114.168236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [114.168351] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [114.168461] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [114.168570] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [114.168679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [114.168789] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [114.168902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [114.169014] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [114.169137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [114.169257] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [114.169375] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [114.169490] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [114.169598] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [114.169705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [114.169812] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [114.169920] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [114.170032] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [114.170161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [114.170281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [114.170396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [114.170505] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [114.170613] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [114.170720] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.170827] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.170938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.171048] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [114.171170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [114.171283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.171390] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.171497] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [114.171604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [114.171710] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [114.171822] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [114.171939] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [114.172051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [114.172180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [114.172295] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [114.172402] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [114.172510] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [114.172616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [114.172725] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:388:pipe C] enable: no [modeset]
<7> [114.172836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:272:plane 1C] fb: [NOFB], visible: no
<7> [114.172949] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:302:plane 2C] fb: [NOFB], visible: no
<7> [114.173059] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:332:plane 3C] fb: [NOFB], visible: no
<7> [114.173193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:362:plane 4C] fb: [NOFB], visible: no
<7> [114.173303] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:372:plane 5C] fb: [NOFB], visible: no
<7> [114.173410] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:382:cursor C] fb: [NOFB], visible: no
<7> [114.173687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [114.174978] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0x88000000)
<7> [114.175425] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [114.175585] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [114.381274] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [114.382366] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe C
<7> [114.393704] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [114.394202] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [114.394664] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [114.395213] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [114.395666] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [114.447900] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [114.448254] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [114.455092] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [114.455470] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x4, on? 1) for [CRTC:388:pipe C]
<7> [114.455518] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [114.456097] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [114.457343] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [114.457795] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [114.458294] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [114.458607] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [114.458903] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [114.459224] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [114.459491] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [114.459753] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [114.460012] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [114.460297] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [114.460556] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [114.460811] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [114.461095] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [114.461355] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [114.461617] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [114.462489] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [114.462940] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [114.463218] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [114.463528] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [114.465064] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [114.465385] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [114.467742] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [114.468018] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (488 ms remaining)
<7> [114.486324] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [114.486643] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [114.486944] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [114.487368] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [114.965539] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [115.041760] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [115.042462] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [115.042976] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [115.079313] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [115.079779] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [115.080148] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [115.080734] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [115.253494] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [115.253819] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [115.254130] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [115.256073] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [115.257613] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [115.258257] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [115.259251] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [115.260473] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [115.261444] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [115.261692] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [115.263139] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [115.263486] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [115.264300] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [115.264723] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [115.265038] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [115.265378] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 192000
<7> [115.281600] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [115.283430] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [115.283877] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [115.286915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C
<7> [115.287351] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x4 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [115.288612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [115.289065] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:388:pipe C]
<7> [115.289585] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [115.290951] [IGT] kms_plane_scaling: exiting, ret=0
<6> [115.298495] Console: switching to colour frame buffer device 180x56
<7> [115.332027] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [115.332680] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [115.333271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
|