Results for igt@kms_frontbuffer_tracking@fbc-1p-primscrn-shrfb-plflip-blt

Result: Pass

i915_display_info21 igt_runner21 results21.json results21-xe-load.json guc_logs21.tar i915_display_info_post_exec21 boot21 dmesg21

DetailValue
Duration 3.43 seconds
Hostname
shard-lnl-2
Igt-Version
IGT-Version: 2.3-g476cbad7c (x86_64) (Linux: 7.0.0-rc3-lgci-xe-xe-4685-71b3cc58bba99c872-debug+ x86_64)
Out
Using IGT_SRANDOM=1773130190 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test DRRS: Not supported.
Starting subtest: fbc-1p-primscrn-shrfb-plflip-blt
Subtest fbc-1p-primscrn-shrfb-plflip-blt: SUCCESS (3.430s)
Err
Starting subtest: fbc-1p-primscrn-shrfb-plflip-blt
Subtest fbc-1p-primscrn-shrfb-plflip-blt: SUCCESS (3.430s)
Dmesg
<6> [341.197195] Console: switching to colour dummy device 80x25
<6> [341.197522] [IGT] kms_frontbuffer_tracking: executing
<7> [341.203028] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [341.203037] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [341.203184] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [341.203414] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [341.203417] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [341.203534] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [341.203737] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [341.203739] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [341.203852] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [341.204089] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]
<7> [341.204091] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]
<7> [341.204532] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [341.204832] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [341.204940] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [341.205045] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [341.205168] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [341.205173] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [341.205175] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [341.205177] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [341.205179] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [341.205182] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [341.205184] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor
<5> [341.205187] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [341.205188] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0
<5> [341.205191] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [341.205205] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes
<7> [341.205345] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [341.205464] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [341.205794] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [341.205797] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [341.205799] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [341.205860] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:
<7> [341.205864] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [341.205868] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [341.205881] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [341.205884] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [341.206031] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [341.206042] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [341.206045] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [341.206180] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [341.206189] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [341.206191] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [341.206306] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [341.213903] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [341.214054] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [341.214170] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [341.214308] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [341.214766] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<6> [341.216134] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-shrfb-plflip-blt
<7> [341.216495] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to f
<7> [341.216594] xe 0000:00:02.0: [drm:intel_psr_debug_set [xe]] Invalid debug mask f
<7> [341.216685] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 1
<7> [341.216826] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 24 (EDID bpp 30, max requested bpp 24, max platform bpp 36)
<7> [341.216923] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [341.217010] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 270000 bpp input 24 compressed 0.0000 HDR no link rate required 1043130 available 1080000
<7> [341.217093] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [341.217167] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [341.217264] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [341.217387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset]
<7> [341.217506] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [341.217611] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [341.217710] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [341.217798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [341.217880] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [341.217959] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [341.218039] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64
<7> [341.218120] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [341.218199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [341.218292] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [341.218387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [341.218480] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [341.218565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [341.218647] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [341.218723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [341.218798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [341.218873] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [341.218947] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [341.219022] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [341.219095] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [341.219169] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [341.219332] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [341.219437] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [341.219539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [341.219625] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [341.219696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [341.219768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [341.219840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [341.219916] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [341.219993] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: yes,
<7> [341.220070] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 40960, rem: 0, den: 1,
<7> [341.220148] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 140, tx_clk_div: 1.
<7> [341.220224] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [341.220315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [341.220404] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0
<7> [341.220493] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [341.220584] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [341.220661] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [341.220737] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23
<7> [341.220814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [341.220889] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [341.220965] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [341.221042] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221119] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [341.221370] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [341.221464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.221721] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [341.221798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [341.221875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [341.221964] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [341.222055] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [341.222172] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [341.222390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [341.222575] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [341.252214] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [341.252370] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [341.257731] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [341.257846] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [341.257955] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [341.258075] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [341.258553] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<7> [341.369111] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [341.369432] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [341.369921] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [341.370394] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [341.370793] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [341.371186] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 8102230/8388608 link 675185/524288, found tu 0, data 0/0 link 0/0)
<7> [341.371561] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [341.371924] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [341.372368] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [341.372723] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [341.373065] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [341.373555] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [341.373898] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [341.374342] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [341.374678] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [341.375010] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [341.375417] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [341.375745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [341.376072] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [341.376476] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [341.376801] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [341.377125] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [341.377594] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [341.377955] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [341.378341] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [341.378684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [341.379025] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [341.379553] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [341.379867] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [341.380157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [341.380546] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [341.380829] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [341.381083] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [341.381365] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [341.381659] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [341.381895] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [341.382114] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [341.382358] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [341.382610] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 270000, found 0)
<7> [341.382818] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [341.383023] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [341.383329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [341.383520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [341.383719] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [341.383870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [341.384007] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [341.384139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [341.384310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [341.384433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [341.384586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [341.384770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [341.384950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [341.385125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [341.385314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [341.385496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [341.385669] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [341.385847] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [341.386008] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [341.386149] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [341.386322] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [341.386434] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [341.386486] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [341.386636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [341.386643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [341.386794] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [341.386790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [341.386922] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [341.387045] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [341.387171] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [341.387311] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [341.387504] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [341.387649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [341.387904] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [341.388019] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [341.594396] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [341.594962] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [341.605887] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [341.606258] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [341.606512] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [341.657773] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [341.658211] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [341.658623] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [341.658973] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [341.659428] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [341.659651] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [341.660120] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [341.660637] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [341.660978] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [341.661378] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [341.661772] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [341.662158] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [341.662482] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [341.662801] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [341.663142] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [341.663456] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [341.663766] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [341.664097] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [341.664372] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [341.664643] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [341.664914] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [341.665378] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [341.665675] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [341.665964] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [341.666559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [341.666968] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [341.667511] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [341.667913] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [341.668414] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [341.668775] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [341.674790] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [341.677827] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [341.686783] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [341.696332] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [341.696473] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [341.696559] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [341.696684] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [341.697075] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [341.697258] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [341.697391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [341.701479] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [341.701516] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [341.701614] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 24 (EDID bpp 30, max requested bpp 24, max platform bpp 36)
<7> [341.701763] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [341.701853] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 270000 bpp input 24 compressed 0.0000 HDR no link rate required 1043130 available 1080000
<7> [341.701939] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [341.702042] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [341.702134] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [341.702227] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [341.702310] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [341.702392] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [341.702473] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [341.702552] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 8102230/8388608 link 675185/524288)
<7> [341.702632] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [341.702711] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [341.702789] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [341.702867] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [341.702943] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [341.703020] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [341.703183] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [341.703262] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [341.703336] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [341.703411] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [341.703488] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [341.703564] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [341.703639] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [341.703713] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [341.703786] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [341.703859] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [341.703931] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [341.704003] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [341.704102] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [341.704181] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [341.704264] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [341.704335] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [341.704405] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [341.704475] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [341.704550] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [341.704629] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [341.704708] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [341.704776] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [341.704844] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [341.704914] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [341.704982] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [341.705059] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [341.705130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 270000)
<7> [341.705204] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [341.705304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [341.705369] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [341.705444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [341.705502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [341.705557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [341.705610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [341.705664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [341.705717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [341.705782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [341.705866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [341.705946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [341.706028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [341.706106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [341.706188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [341.706263] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [341.706353] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [341.706436] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [341.706512] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [341.706586] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [341.706671] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [341.706743] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [341.706818] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [341.706894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [341.706972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [341.707058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [341.707139] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [341.707220] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [341.707294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [341.707369] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64
<7> [341.707442] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [341.707515] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [341.707587] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [341.707658] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [341.707729] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [341.707800] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [341.707870] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [341.707940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [341.708010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [341.708094] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [341.708171] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [341.708244] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [341.708315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [341.708385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [341.708455] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [341.708524] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [341.708594] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [341.708663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [341.708732] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [341.708800] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [341.708869] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [341.708936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [341.709005] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: yes,
<7> [341.709084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 40960, rem: 0, den: 1,
<7> [341.709158] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 140, tx_clk_div: 1.
<7> [341.709231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [341.709300] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [341.709368] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0
<7> [341.709437] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [341.709506] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [341.709576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [341.709649] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23
<7> [341.709722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [341.709793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [341.709864] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [341.709936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710007] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710090] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710166] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [341.710239] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [341.710309] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [341.710516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [341.710584] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [341.710652] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:428] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [341.710722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [341.710789] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [341.710857] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [341.710925] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [341.710992] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [341.711088] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [341.711166] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [341.711463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [341.711548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [341.711655] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [341.711781] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [341.711872] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [341.711960] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [341.712049] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [341.712133] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [341.712205] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [341.712269] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [341.712332] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [341.712393] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [341.712453] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [341.712513] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [341.712572] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [341.712631] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [341.712690] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [341.712748] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [341.712810] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [341.712878] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [341.712969] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [341.713136] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [341.713203] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [341.713304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [341.714127] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [341.714229] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [341.716134] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [341.716219] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (442 ms remaining)
<7> [342.156068] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [342.218369] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [342.218544] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [342.218700] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [342.231816] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [342.232294] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [342.232739] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [342.268606] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [342.268987] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [342.269350] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [342.269785] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [342.444263] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [342.444673] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [342.445062] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [342.447145] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [342.448690] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [342.449592] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 03
<7> [342.450832] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [342.452334] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [342.453558] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [342.454032] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [342.455595] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [342.456012] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 270000, lane count = 4
<7> [342.456955] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [342.457471] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [342.457952] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [342.458385] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 192000
<7> [342.474907] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [342.475433] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [342.479765] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [342.509131] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [342.509622] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [342.510114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [342.542228] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [342.542750] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [342.559330] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:428] from all active usage due to RMFB ioctl
<7> [342.559463] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:428] is removed
<7> [342.559602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [342.560056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [342.560392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [342.560741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [342.561131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [342.561475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [342.561928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [342.562355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [342.562729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [342.563184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [342.563586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [342.587439] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [342.588015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [342.588339] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]
<7> [342.588665] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]
<7> [342.591496] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [342.591636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [342.591733] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [342.708218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [342.708638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [342.807994] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [342.808085] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [342.808283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [342.808631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [342.809048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [342.809359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [342.809669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [342.810085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [342.810532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [342.810973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [342.811397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [342.811872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [342.812291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [342.831020] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [342.836631] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [342.859079] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [342.859611] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [342.891608] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [342.892156] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [342.892647] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [342.925265] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [342.925714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [342.941515] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [342.941635] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [342.958352] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [342.992044] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [342.992581] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [342.993081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.025381] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.025723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.041333] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [343.041443] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [343.058362] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.091502] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.092002] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.092548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.125202] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.125691] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.141375] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [343.141485] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [343.158250] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.191937] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.192495] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.193037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.225390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.225757] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.249259] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:440] from all active usage due to RMFB ioctl
<7> [343.249370] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:440] is removed
<7> [343.249473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [343.249828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [343.250291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [343.250646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [343.251068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [343.251424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [343.252061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [343.252507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [343.252915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [343.253281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [343.253666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [343.274530] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.275058] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.275410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.276171] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.276470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.374498] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [343.374591] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [343.374790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [343.375208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [343.375553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [343.375858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [343.376297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [343.376670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [343.377123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [343.377559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [343.377970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [343.378404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [343.378794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [343.381355] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [343.381731] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]
<7> [343.397981] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [343.402781] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [343.425510] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.426090] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.457799] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.458353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.458887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.492022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.492484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.510475] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.541448] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.541945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.542474] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.575326] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.575713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.609272] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.609544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.609732] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.610184] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [343.650963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.651080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.759807] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.791739] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.792283] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.792781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.825226] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.825614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.843433] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [343.874607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.875160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.875707] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.908345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.908712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.941659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [343.942035] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [343.942339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [343.954103] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [343.954327] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [343.991510] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.024464] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.024889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.025236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.058562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.059100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.077836] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.109276] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.109724] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.110106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.141931] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.142328] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.174536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.174945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.175266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.188266] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.188460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.224612] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.258357] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.258917] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.259477] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.291791] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.292197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.310207] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.341198] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.341691] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.342164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.375051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.375418] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.408195] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.408558] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.408843] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.427337] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.427655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.474703] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.507817] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.508325] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.508746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.542058] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.542594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [344.560516] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [344.591679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [344.592177] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [344.592668] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [344.625218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [344.625642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<6> [344.647493] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-shrfb-plflip-blt, SUCCESS
<7> [344.651691] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:435] from all active usage due to RMFB ioctl
<7> [344.651838] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:435] is removed
<7> [344.651957] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [344.652346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [344.652698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [344.653112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [344.653462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [344.653835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [344.654316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [344.654720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [344.655161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [344.655575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [344.655992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [344.657293] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]
<7> [344.675941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [344.676340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [344.676799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [344.677146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [344.677588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [344.678004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [344.678516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [344.678963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [344.679405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [344.679914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [344.680357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [344.682910] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 11059200 bytes of contiguous stolen space for FBC, limit: 2
<7> [344.683326] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]
<7> [344.690674] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [344.691932] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [344.692491] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 0
<7> [344.693341] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 24 (EDID bpp 30, max requested bpp 24, max platform bpp 36)
<7> [344.693885] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [344.694356] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 270000 bpp input 24 compressed 0.0000 HDR no link rate required 1043130 available 1080000
<7> [344.694803] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [344.695900] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [344.696404] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset]
<7> [344.696745] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [344.697065] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [344.697464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [344.697760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [344.698033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [344.698396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [344.698648] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64
<7> [344.698887] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [344.699125] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [344.699395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [344.699655] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [344.699868] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [344.700076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [344.700313] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [344.700533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [344.700728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [344.700907] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [344.701084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [344.701281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [344.701446] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [344.701602] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [344.701756] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [344.701906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [344.702074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [344.702263] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [344.702416] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [344.702549] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [344.702680] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [344.702809] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [344.702936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [344.703076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [344.703244] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [344.703374] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [344.703486] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [344.703598] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [344.703706] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: yes,
<7> [344.703814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 40960, rem: 0, den: 1,
<7> [344.703918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 140, tx_clk_div: 1.
<7> [344.704024] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [344.704236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [344.704339] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0
<7> [344.704435] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [344.704531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [344.704624] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [344.704717] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23
<7> [344.704807] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [344.704896] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [344.704985] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [344.705083] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705175] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705267] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [344.705444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [344.705526] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [344.705759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [344.705837] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [344.705913] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [344.705991] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [344.706228] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [344.707192] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]
<7> [344.724009] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [344.725327] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [344.725818] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<6> [344.740955] Console: switching to colour frame buffer device 180x56
Created at 2026-03-10 08:51:41