Result: 10 Warning(s)
igt_runner0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 2.04 seconds |
| Igt-Version |
IGT-Version: 2.3-ge91464aaa (x86_64) (Linux: 7.0.0-rc3-lgci-xe-xe-4681-5bb4c677496179faf-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1773071793 for randomisation Opened device: /dev/dri/card0 Using monotonic timestamps Starting subtest: basic-flip-vs-wf_vblank Starting dynamic subtest: A-eDP1 3840x2160: 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa Expected frametime: 16665us; measured 16665.7us +- 3.790us accuracy 0.07% Event flip: expected 30, counted 30, passrate = 100.00%, encoder type 2 Event vblank: expected 30, counted 30, passrate = 100.00%, encoder type 2 Dynamic subtest A-eDP1: SUCCESS (2.041s) |
| Err |
Starting subtest: basic-flip-vs-wf_vblank Starting dynamic subtest: A-eDP1 Dynamic subtest A-eDP1: SUCCESS (2.041s) |
| Dmesg |
<6> [215.926014] Console: switching to colour dummy device 80x25
<6> [215.926179] [IGT] kms_flip: executing
<7> [215.935311] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1]
<7> [215.935320] xe 0000:00:02.0: [drm:intel_hdmi_detect [xe]] [CONNECTOR:516:HDMI-A-1]
<7> [215.939494] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1] disconnected
<7> [215.939814] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1]
<7> [215.939818] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:525:DP-1]
<7> [215.940024] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [215.940194] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1] disconnected
<7> [215.940578] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [215.940581] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:535:DP-2]
<7> [215.940739] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [215.940866] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_USBC2
<7> [215.940999] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> legacy) pin assignment: - max lanes: 4
<7> [215.962048] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [215.983015] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.003978] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.024967] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.045947] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.066926] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.087888] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.108854] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.129822] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.150779] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.171748] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.192712] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.213675] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.234637] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.255590] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.276554] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.297512] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.318467] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.339426] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.360382] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.381337] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.402290] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.423241] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.444199] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.465159] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.486113] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.507062] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.528013] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.548968] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.569951] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.590929] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.611899] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.612014] xe 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX USBC2/DDI TC2/PHY TC2: Too many retries, giving up. First error: -110
<7> [216.612036] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [216.612382] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [216.612386] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:544:DP-3]
<7> [216.612536] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [216.612644] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [216.612928] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [216.612930] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:553:DP-4]
<7> [216.613081] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port G/TC#4: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [216.613226] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [216.613761] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [216.613765] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:507:eDP-1]
<7> [216.614194] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [216.614480] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [216.614618] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [216.614715] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [216.614831] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [216.614837] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [216.614841] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [216.614843] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [216.614859] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] VRR capable: no
<7> [216.614948] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [216.615049] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [216.615441] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [216.615446] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [216.615451] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [216.615473] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1]
<7> [216.615478] xe 0000:00:02.0: [drm:intel_hdmi_detect [xe]] [CONNECTOR:516:HDMI-A-1]
<7> [216.619648] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1] disconnected
<7> [216.619663] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1]
<7> [216.619667] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:525:DP-1]
<7> [216.619829] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1] disconnected
<7> [216.619839] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [216.619841] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:535:DP-2]
<7> [216.640845] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.661834] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.682810] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.703766] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.724718] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.745674] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.766628] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.787580] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.808532] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.829486] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.850443] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.871396] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.892348] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.913312] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.934269] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.955221] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.976173] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [216.997126] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.018079] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.039030] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.059978] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.080976] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.101971] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.122966] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.143956] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.164939] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.185918] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.206886] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.227856] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.248819] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.269785] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.290736] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [217.290841] xe 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX USBC2/DDI TC2/PHY TC2: Too many retries, giving up. First error: -110
<7> [217.290861] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [217.290887] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [217.290890] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:544:DP-3]
<7> [217.291060] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [217.291080] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [217.291084] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:553:DP-4]
<7> [217.291274] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<6> [217.291643] [IGT] kms_flip: starting subtest basic-flip-vs-wf_vblank
<6> [217.294301] [IGT] kms_flip: starting dynamic subtest A-eDP1
<7> [217.294832] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:561]
<7> [217.295038] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:564]
<7> [217.419491] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [217.419705] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [217.419867] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [217.420012] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [217.420177] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [217.420294] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [217.420406] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [217.420516] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [217.420618] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [217.420742] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [217.420838] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [217.420932] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [217.421043] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [217.421151] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [217.421243] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [217.421337] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [217.421429] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [217.421520] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [217.421608] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [217.421695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [217.421779] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [217.421864] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [217.421950] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [217.422049] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [217.422144] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [217.422228] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [217.422314] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [217.422398] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [217.422483] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [217.422567] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [217.422652] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [217.422742] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [217.422831] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [217.422937] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [217.423039] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [217.423142] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [217.423230] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [217.423318] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [217.423405] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [217.423493] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [217.423580] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [217.423667] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [217.423793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [217.423873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [217.423967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [217.424056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [217.424143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [217.424215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [217.424285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [217.424358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [217.424444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [217.424555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 0
<7> [217.424649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 0
<7> [217.424740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 0
<7> [217.424830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 0
<7> [217.424917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 0
<7> [217.425020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 0
<7> [217.425124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 0
<7> [217.425213] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [217.425319] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [217.425431] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Modeset required for cdclk change
<7> [217.425521] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [217.425609] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [217.425701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [217.425796] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [217.425888] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [217.425979] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [217.426088] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [217.426190] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [217.426279] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [217.426413] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [217.429577] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [217.633314] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:507:eDP-1] set backlight PWM = 0
<7> [217.634444] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [217.646510] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turn panel power off
<7> [217.647125] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [217.647652] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [217.649187] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [217.702255] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [217.702802] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:506:DDI A/PHY A] - long
<7> [217.703277] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [217.703880] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:506:DDI A/PHY A]
<7> [217.709312] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [217.709676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DDI_IO_A
<7> [217.710097] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [217.710444] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [217.710744] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [217.711086] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [217.711601] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=448
<7> [217.711903] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:506:DDI A/PHY A]
<7> [217.712197] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:515:DDI B/PHY B]
<7> [217.712451] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:524:DDI TC1/PHY TC1]
<7> [217.712683] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:526:DP-MST A]
<7> [217.712911] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:527:DP-MST B]
<7> [217.713164] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:528:DP-MST C]
<7> [217.713396] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:529:DP-MST D]
<7> [217.713626] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DDI TC2/PHY TC2]
<7> [217.713836] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST A]
<7> [217.714055] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:537:DP-MST B]
<7> [217.714263] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:538:DP-MST C]
<7> [217.714526] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:539:DP-MST D]
<7> [217.714728] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DDI TC3/PHY TC3]
<7> [217.714885] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST A]
<7> [217.714962] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:546:DP-MST B]
<7> [217.715051] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:547:DP-MST C]
<7> [217.715130] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:548:DP-MST D]
<7> [217.715206] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:552:DDI TC4/PHY TC4]
<7> [217.715280] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:554:DP-MST A]
<7> [217.715354] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:555:DP-MST B]
<7> [217.715429] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:556:DP-MST C]
<7> [217.715502] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:557:DP-MST D]
<7> [217.715576] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:507:eDP-1]
<7> [217.715672] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [217.715746] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [217.715820] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [217.715963] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [217.716092] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [217.716350] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [217.716490] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [217.716590] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:504:pipe D]
<7> [217.716683] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [217.716710] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:507:eDP-1]
<7> [217.716765] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:507:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [217.716880] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:506:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [217.716988] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [217.717091] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [217.717201] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:506:DDI A/PHY A] [CRTC:150:pipe A]
<7> [217.717298] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [217.717393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [217.717486] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [217.717581] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [217.717674] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [217.717765] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [217.717854] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [217.717942] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [217.718042] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [217.718130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [217.718218] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [217.718306] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [217.718394] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [217.718482] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [217.718569] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [217.718657] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [217.718745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [217.718831] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [217.718918] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [217.719010] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [217.719097] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [217.719182] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [217.719268] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [217.719353] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [217.719450] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [217.719540] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [217.719626] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [217.719711] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [217.719797] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [217.719884] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [217.719968] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [217.720068] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [217.720154] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [217.720239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [217.720324] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [217.720408] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [217.720493] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [217.720612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [217.720691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [217.720790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [217.720862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [217.720933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [217.721015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [217.721087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [217.721173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [217.721260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [217.721358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 2155
<7> [217.721451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 2155
<7> [217.721545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 2155
<7> [217.721635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 2155
<7> [217.721725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 2155
<7> [217.721815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 2155
<7> [217.721904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 2155
<7> [217.721998] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [217.722104] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [217.722212] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Modeset required for cdclk change
<7> [217.722302] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [217.722390] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [217.722479] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [217.722570] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [217.722659] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [217.722756] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [217.722848] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [217.722952] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [217.723053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [217.723144] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [217.723233] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [217.723321] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [217.723408] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [217.723495] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [217.723582] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [217.723669] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [217.723758] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [217.723849] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [217.723938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [217.724035] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [217.724122] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [217.724208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [217.724295] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [217.724380] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [217.724468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [217.724554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [217.724641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [217.724727] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [217.724814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [217.724901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [217.724996] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [217.725083] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [217.725170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [217.725258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [217.725344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [217.725432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 60, ips linetime: 0
<7> [217.725529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [217.725616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [217.725702] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [217.725788] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [217.725874] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [217.725961] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [217.726063] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [217.726149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726322] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [217.726493] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [217.726578] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [217.726833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [217.726919] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [217.727010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:561] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [217.727098] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [217.727183] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [217.727283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [217.727369] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [217.727454] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [217.727539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [217.727622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [217.728030] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [217.728164] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [217.728393] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=768
<7> [217.728490] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:506:DDI A/PHY A]
<7> [217.728577] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:515:DDI B/PHY B]
<7> [217.728660] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:524:DDI TC1/PHY TC1]
<7> [217.728740] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:526:DP-MST A]
<7> [217.728819] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:527:DP-MST B]
<7> [217.728899] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:528:DP-MST C]
<7> [217.728985] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:529:DP-MST D]
<7> [217.729065] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DDI TC2/PHY TC2]
<7> [217.729142] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST A]
<7> [217.729220] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:537:DP-MST B]
<7> [217.729296] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:538:DP-MST C]
<7> [217.729371] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:539:DP-MST D]
<7> [217.729447] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DDI TC3/PHY TC3]
<7> [217.729522] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST A]
<7> [217.729597] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:546:DP-MST B]
<7> [217.729670] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:547:DP-MST C]
<7> [217.729743] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:548:DP-MST D]
<7> [217.729831] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:552:DDI TC4/PHY TC4]
<7> [217.729918] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:554:DP-MST A]
<7> [217.730032] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:555:DP-MST B]
<7> [217.730109] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:556:DP-MST C]
<7> [217.730185] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:557:DP-MST D]
<7> [217.730269] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [217.730407] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [217.730482] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [217.730560] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [217.730679] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [217.730766] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [217.730880] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turn panel power on
<7> [217.730990] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power cycle (479 ms remaining)
<7> [218.217461] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [218.258751] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [218.259491] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power on
<7> [218.260042] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [218.321703] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [218.322274] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:506:DDI A/PHY A] - long
<7> [218.322762] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [218.323363] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:506:DDI A/PHY A]
<7> [218.353242] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port G/TC#4: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [218.353384] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [218.353530] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_USBC2
<7> [218.354301] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [218.354824] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (legacy -> disconnected) pin assignment: - max lanes: 4
<7> [218.474157] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [218.474745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DDI_IO_A
<7> [218.475484] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turning VDD on
<7> [218.476027] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [218.477938] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [218.478033] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [218.478719] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [218.479730] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [218.479872] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [218.480559] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Clock recovery OK
<7> [218.480647] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [218.481736] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [218.481823] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [218.482274] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [218.482391] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [218.482479] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [218.482575] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:507:eDP-1] Performing OUI wait (0 ms)
<7> [218.482910] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:507:eDP-1] set backlight PWM = 6844
<4> [218.499254] handle_plane_fault: 34972 callbacks suppressed
<3> [218.499271] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499315] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499333] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499349] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499365] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499381] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499396] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499412] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499428] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [218.499444] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<7> [218.499426] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [218.501219] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:507:eDP-1]
<7> [218.501638] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [219.305006] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:561] from all active usage due to RMFB ioctl
<7> [219.305051] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:561] is removed
<7> [219.305094] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [219.305200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [219.305279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.305355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.305429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.305518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [219.305617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 0
<7> [219.305711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 0
<7> [219.305804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 0
<7> [219.305899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 0
<7> [219.306004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 0
<7> [219.306100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 0
<7> [219.306192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 0
<7> [219.306317] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<6> [219.335299] [IGT] kms_flip: finished subtest A-eDP1, SUCCESS
|