Result: 10 Warning(s)
igt_runner0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 2.05 seconds |
| Igt-Version |
IGT-Version: 2.3-gc7d12b349 (x86_64) (Linux: 7.0.0-rc2-lgci-xe-xe-4675-fce8d7fb2107068c2-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1772854468 for randomisation Opened device: /dev/dri/card0 Using monotonic timestamps Starting subtest: basic-flip-vs-wf_vblank Starting dynamic subtest: A-eDP1 3840x2160: 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa Expected frametime: 16665us; measured 16665.9us +- 4.031us accuracy 0.07% Event flip: expected 30, counted 30, passrate = 100.00%, encoder type 2 Event vblank: expected 30, counted 30, passrate = 100.00%, encoder type 2 Dynamic subtest A-eDP1: SUCCESS (2.048s) |
| Err |
Starting subtest: basic-flip-vs-wf_vblank Starting dynamic subtest: A-eDP1 Dynamic subtest A-eDP1: SUCCESS (2.048s) |
| Dmesg |
<6> [225.733515] Console: switching to colour dummy device 80x25
<6> [225.733679] [IGT] kms_flip: executing
<7> [225.743635] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1]
<7> [225.743644] xe 0000:00:02.0: [drm:intel_hdmi_detect [xe]] [CONNECTOR:516:HDMI-A-1]
<7> [225.747854] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1] disconnected
<7> [225.748195] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1]
<7> [225.748198] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:525:DP-1]
<7> [225.748495] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [225.748669] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1] disconnected
<7> [225.748988] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [225.748991] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:535:DP-2]
<7> [225.749155] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [225.749312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_USBC2
<7> [225.749495] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> legacy) pin assignment: - max lanes: 4
<7> [225.770519] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.791492] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.812460] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.833425] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.854383] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.875340] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.896300] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.917261] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.938226] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.959224] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [225.980216] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.001203] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.022184] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.043159] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.064119] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.085102] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.106072] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.127026] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.147982] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.168956] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.189942] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.210914] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.231879] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.252840] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.273799] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.294759] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.315720] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.336675] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.357631] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.378592] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.399553] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.420511] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.420621] xe 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX USBC2/DDI TC2/PHY TC2: Too many retries, giving up. First error: -110
<7> [226.420642] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [226.421009] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [226.421012] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:544:DP-3]
<7> [226.421164] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [226.421287] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [226.421600] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [226.421603] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:553:DP-4]
<7> [226.421781] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port G/TC#4: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [226.421889] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [226.422327] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [226.422330] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:507:eDP-1]
<7> [226.422773] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [226.423071] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [226.423167] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [226.423278] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [226.423396] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [226.423402] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [226.423405] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [226.423408] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [226.423430] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] VRR capable: no
<7> [226.423543] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [226.423641] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [226.424019] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [226.424022] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [226.424026] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [226.424040] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1]
<7> [226.424043] xe 0000:00:02.0: [drm:intel_hdmi_detect [xe]] [CONNECTOR:516:HDMI-A-1]
<7> [226.428208] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:HDMI-A-1] disconnected
<7> [226.428223] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1]
<7> [226.428226] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:525:DP-1]
<7> [226.428421] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:525:DP-1] disconnected
<7> [226.428433] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [226.428436] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:535:DP-2]
<7> [226.449439] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.470398] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.491358] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.512315] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.533268] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.554226] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.575222] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.596212] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.617197] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.638178] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.659158] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.680123] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.701086] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.722047] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.743005] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.763962] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.784914] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.805873] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.826834] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.847787] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.868739] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.889690] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.910653] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.931616] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.952580] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.973537] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [226.994494] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.015452] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.036411] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.057368] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.078321] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.099273] xe 0000:00:02.0: [drm:intel_dp_aux_xfer [xe]] AUX USBC2/DDI TC2/PHY TC2: timeout (status 0x7d40023f)
<7> [227.099386] xe 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX USBC2/DDI TC2/PHY TC2: Too many retries, giving up. First error: -110
<7> [227.099405] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [227.099434] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [227.099437] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:544:DP-3]
<7> [227.099597] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [227.099606] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [227.099608] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:553:DP-4]
<7> [227.099754] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<6> [227.100056] [IGT] kms_flip: starting subtest basic-flip-vs-wf_vblank
<6> [227.102546] [IGT] kms_flip: starting dynamic subtest A-eDP1
<7> [227.103032] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:561]
<7> [227.103223] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:564]
<7> [227.225861] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [227.225979] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [227.226134] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [227.226280] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [227.226459] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [227.226637] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [227.226781] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [227.226899] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [227.227006] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [227.227114] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [227.227221] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [227.227391] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [227.227505] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [227.227606] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [227.227701] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [227.227800] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [227.227898] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [227.228023] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [227.228118] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [227.228218] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [227.228370] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [227.228508] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [227.228610] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [227.228709] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [227.228805] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [227.228926] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [227.229022] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [227.229117] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [227.229218] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [227.229326] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [227.229423] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [227.229518] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [227.229611] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [227.229704] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [227.229802] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [227.229926] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [227.230026] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [227.230130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [227.230226] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [227.230343] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [227.230437] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [227.230531] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [227.230685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [227.230768] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [227.230875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [227.230955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [227.231032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [227.231113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [227.231188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [227.231274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [227.231362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [227.231466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 0
<7> [227.231589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 0
<7> [227.231686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 0
<7> [227.231790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 0
<7> [227.231886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 0
<7> [227.231984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 0
<7> [227.232077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 0
<7> [227.232170] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [227.232311] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [227.232432] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Modeset required for cdclk change
<7> [227.232526] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [227.232627] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [227.232727] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [227.232833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [227.232929] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [227.233024] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [227.233140] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [227.233247] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [227.233347] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [227.233492] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [227.236649] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [227.439665] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:507:eDP-1] set backlight PWM = 0
<7> [227.440778] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [227.463301] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turn panel power off
<7> [227.463862] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [227.464454] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [227.479566] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [227.519035] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [227.519598] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:506:DDI A/PHY A] - long
<7> [227.520103] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [227.520692] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:506:DDI A/PHY A]
<7> [227.523905] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [227.524281] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DDI_IO_A
<7> [227.524601] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [227.524895] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [227.525171] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [227.525538] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [227.525992] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=448
<7> [227.526360] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:506:DDI A/PHY A]
<7> [227.526661] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:515:DDI B/PHY B]
<7> [227.526910] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:524:DDI TC1/PHY TC1]
<7> [227.527154] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:526:DP-MST A]
<7> [227.527407] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:527:DP-MST B]
<7> [227.527633] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:528:DP-MST C]
<7> [227.527902] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:529:DP-MST D]
<7> [227.528109] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DDI TC2/PHY TC2]
<7> [227.528350] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST A]
<7> [227.528571] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:537:DP-MST B]
<7> [227.528771] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:538:DP-MST C]
<7> [227.528970] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:539:DP-MST D]
<7> [227.529168] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DDI TC3/PHY TC3]
<7> [227.529387] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST A]
<7> [227.529670] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:546:DP-MST B]
<7> [227.529900] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:547:DP-MST C]
<7> [227.530127] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:548:DP-MST D]
<7> [227.530356] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:552:DDI TC4/PHY TC4]
<7> [227.530561] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:554:DP-MST A]
<7> [227.530820] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:555:DP-MST B]
<7> [227.531047] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:556:DP-MST C]
<7> [227.531272] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:557:DP-MST D]
<7> [227.531477] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:507:eDP-1]
<7> [227.531699] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [227.531868] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [227.532078] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [227.532347] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [227.532575] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [227.532989] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [227.533221] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [227.533385] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:504:pipe D]
<7> [227.533542] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [227.533579] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:507:eDP-1]
<7> [227.533664] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:507:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [227.533846] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:506:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [227.533999] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [227.534143] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [227.534302] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:506:DDI A/PHY A] [CRTC:150:pipe A]
<7> [227.534443] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [227.534618] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [227.534755] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [227.534883] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [227.535014] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [227.535129] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [227.535253] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [227.535381] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [227.535512] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [227.535615] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [227.535726] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [227.535831] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [227.535934] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [227.536033] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [227.536128] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [227.536251] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [227.536346] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [227.536439] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [227.536540] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [227.536636] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [227.536742] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [227.536842] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [227.536938] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [227.537032] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [227.537139] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [227.537256] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [227.537352] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [227.537452] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [227.537545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [227.537645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [227.537739] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [227.537831] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [227.537935] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [227.538042] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [227.538136] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [227.538244] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [227.538346] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [227.538483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [227.538567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [227.538668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [227.538746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [227.538839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [227.538935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [227.539013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [227.539099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [227.539191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [227.539305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 2155
<7> [227.539411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 2155
<7> [227.539510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 2155
<7> [227.539631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 2155
<7> [227.539725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 2155
<7> [227.539817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 2155
<7> [227.539910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 2155
<7> [227.540003] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [227.540116] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [227.540234] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Modeset required for cdclk change
<7> [227.540332] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [227.540426] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [227.540519] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [227.540617] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [227.540743] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [227.540843] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [227.540941] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [227.541039] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [227.541141] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [227.541242] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [227.541343] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [227.541437] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [227.541530] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [227.541650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [227.541750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [227.541846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [227.541946] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [227.542037] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [227.542136] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [227.542234] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [227.542328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [227.542433] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [227.542537] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [227.542633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [227.542736] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [227.542830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [227.542922] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [227.543023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [227.543117] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [227.543213] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [227.543330] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [227.543436] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [227.543555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [227.543648] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [227.543741] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [227.543840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 60, ips linetime: 0
<7> [227.543931] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [227.544030] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [227.544123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [227.544214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [227.544338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [227.544438] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [227.544529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [227.544627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.544724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.544819] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.544918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [227.545009] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [227.545108] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.545218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.545328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [227.545428] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [227.545523] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [227.545616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:561] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [227.545714] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [227.545807] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [227.545901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [227.545993] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [227.546112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [227.546205] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [227.546306] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [227.546726] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [227.546870] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [227.547126] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=768
<7> [227.547239] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:506:DDI A/PHY A]
<7> [227.547333] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:515:DDI B/PHY B]
<7> [227.547426] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:524:DDI TC1/PHY TC1]
<7> [227.547511] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:526:DP-MST A]
<7> [227.547602] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:527:DP-MST B]
<7> [227.547713] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:528:DP-MST C]
<7> [227.547797] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:529:DP-MST D]
<7> [227.547883] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DDI TC2/PHY TC2]
<7> [227.547972] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST A]
<7> [227.548060] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:537:DP-MST B]
<7> [227.548146] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:538:DP-MST C]
<7> [227.548242] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:539:DP-MST D]
<7> [227.548327] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DDI TC3/PHY TC3]
<7> [227.548411] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST A]
<7> [227.548494] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:546:DP-MST B]
<7> [227.548595] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:547:DP-MST C]
<7> [227.548700] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:548:DP-MST D]
<7> [227.548783] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:552:DDI TC4/PHY TC4]
<7> [227.548867] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:554:DP-MST A]
<7> [227.548954] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:555:DP-MST B]
<7> [227.549037] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:556:DP-MST C]
<7> [227.549120] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:557:DP-MST D]
<7> [227.549222] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [227.549415] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [227.549519] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [227.549605] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [227.549733] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [227.549834] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [227.549960] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turn panel power on
<7> [227.550074] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power cycle (475 ms remaining)
<7> [228.031645] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [228.072916] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [228.073627] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 wait for panel power on
<7> [228.074161] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [228.119515] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port G/TC#4: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [228.119571] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [228.119583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_USBC2
<7> [228.120386] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [228.120855] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (legacy -> disconnected) pin assignment: - max lanes: 4
<7> [228.135744] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [228.136284] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:506:DDI A/PHY A] - long
<7> [228.136744] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [228.137344] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:506:DDI A/PHY A]
<7> [228.288645] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [228.289311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DDI_IO_A
<7> [228.289992] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 turning VDD on
<7> [228.290601] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:506:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [228.292610] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [228.292710] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [228.293458] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [228.294535] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [228.294787] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [228.295525] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Clock recovery OK
<7> [228.295662] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [228.296776] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [228.296913] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:507:eDP-1][ENCODER:506:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [228.297417] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [228.297585] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [228.297721] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [228.297866] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:507:eDP-1] Performing OUI wait (0 ms)
<7> [228.298273] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:507:eDP-1] set backlight PWM = 6844
<4> [228.314443] handle_plane_fault: 36347 callbacks suppressed
<3> [228.314459] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314518] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314540] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314559] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314579] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314598] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314617] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314638] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314657] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<3> [228.314679] xe 0000:00:02.0: [drm] *ERROR* [CRTC:150:pipe A][PLANE:34:plane 1A] fault (CTL=0x94000400, SURF=0x4200000, SURFLIVE=0x4200000)
<7> [228.314621] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [228.316462] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:507:eDP-1]
<7> [228.316975] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [229.120116] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:561] from all active usage due to RMFB ioctl
<7> [229.120260] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:561] is removed
<7> [229.120361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [229.120661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [229.120742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [229.120820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [229.120896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [229.120986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [229.121086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 11064 required 0
<7> [229.121182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 13813 required 0
<7> [229.121290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 14899 required 0
<7> [229.121391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 13010 required 0
<7> [229.121490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 0: max bw 34133 required 0
<7> [229.121584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 1: max bw 51200 required 0
<7> [229.121680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] PSF GV point 2: max bw 51200 required 0
<7> [229.121808] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<6> [229.150581] [IGT] kms_flip: finished subtest A-eDP1, SUCCESS
|