Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

i915_display_info3 igt_runner3 results3.json results3-xe-load.json guc_logs3.tar i915_display_info_post_exec3 boot3 dmesg3

DetailValue
Duration 1.45 seconds
Hostname 
shard-lnl-4
Igt-Version 
IGT-Version: 2.3-g2020b0bf9 (x86_64) (Linux: 6.19.0-lgci-xe-xe-4576-cc2c646d39200973c-debug+ x86_64)
Out 
Using IGT_SRANDOM=1771527717 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.450s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.450s)
Dmesg
<6> [446.667148] Console: switching to colour dummy device 80x25
<6> [446.667418] [IGT] kms_pm_rpm: executing
<7> [446.673016] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [446.673026] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [446.673228] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [446.673535] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [446.673537] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [446.673696] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [446.674013] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [446.674017] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [446.674171] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [446.674554] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]
<7> [446.674557] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]
<7> [446.675047] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [446.675438] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [446.675614] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [446.675787] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [446.676323] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [446.676338] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.676344] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.676348] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [446.676357] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [446.676364] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.676369] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor
<5> [446.676377] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.676381] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0
<5> [446.676389] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.676422] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes
<7> [446.676762] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [446.677112] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [446.677735] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.677738] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.677741] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.677837] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:
<7> [446.677841] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [446.677847] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [446.677875] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [446.677879] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [446.678091] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [446.678128] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [446.678136] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [446.678577] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [446.678620] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [446.678629] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [446.679079] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [446.679100] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]
<7> [446.679103] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]
<7> [446.679584] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [446.679925] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [446.680056] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [446.680367] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [446.680881] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [446.680894] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.680900] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.680905] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [446.680914] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [446.680923] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.680928] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor
<5> [446.680940] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.680947] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0
<5> [446.680958] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.680993] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes
<7> [446.681183] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [446.681313] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [446.681918] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.681921] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [446.681923] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [446.682002] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:
<7> [446.682005] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [446.682010] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [446.682063] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [446.682073] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [446.682512] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [446.682637] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [446.682644] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [446.683113] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [446.683158] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [446.683162] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [446.683331] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [446.690785] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429]
<7> [446.718510] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [446.718592] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [446.718709] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [446.718803] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [446.718945] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [446.719050] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [446.719145] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [446.719239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [446.719330] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [446.719420] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [446.719508] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [446.719588] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [446.719669] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [446.719758] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [446.719846] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [446.719957] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [446.720062] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [446.720164] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [446.720263] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [446.720348] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [446.720432] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [446.720514] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [446.720595] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [446.720676] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [446.720771] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [446.720880] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [446.720974] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [446.721069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [446.721159] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [446.721239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [446.721318] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [446.721397] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [446.721474] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [446.721552] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [446.721628] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [446.721708] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [446.721800] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [446.721911] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [446.722007] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [446.722105] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [446.722191] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [446.722351] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [446.722424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [446.722515] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [446.722589] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [446.722655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [446.722715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [446.722775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [446.722840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [446.723178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [446.723269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [446.723358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [446.723446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [446.723533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [446.723618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [446.723702] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [446.723800] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [446.723910] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [446.724020] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [446.724120] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [446.724231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [446.724314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [446.724399] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [446.724484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [446.724567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [446.724650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [446.724732] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [446.724868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [446.724997] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [446.725171] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [446.735462] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [446.735629] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [446.939139] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [446.939685] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [446.950431] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [446.950831] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [446.950863] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [446.951324] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [446.951332] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [447.002561] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [447.003007] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [447.003047] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [447.003229] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [447.003674] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [447.004151] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [447.004419] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [447.004824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [447.005338] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [447.005677] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [447.006020] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [447.006358] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [447.006648] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [447.006959] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [447.007219] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [447.007479] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [447.007790] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [447.008115] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [447.008398] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [447.008674] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [447.008988] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [447.009256] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [447.009600] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [447.009864] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [447.010152] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [447.010635] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [447.011093] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [447.011607] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [447.011957] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [447.012369] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [447.012676] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [447.013589] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [447.014004] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [447.031915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [447.032434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [447.032904] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [447.039632] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [447.039938] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [447.040222] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [447.040517] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [447.691179] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [447.691318] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [447.691478] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [447.692371] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [447.692549] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [447.693378] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [447.693887] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [447.694315] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [447.694916] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [447.695355] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<6> [447.717986] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [447.753338] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [447.753732] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [447.754146] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [447.754323] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [447.754510] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [447.754675] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [447.756271] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [447.756502] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [447.756736] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [447.757106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [447.757425] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [447.757648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [447.757925] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [447.758092] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [447.758287] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [447.758426] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [447.758592] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [447.758718] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [447.758889] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [447.759028] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [447.759121] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [447.759434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [447.759653] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [447.776921] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [447.777488] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [447.778006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [448.778993] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [448.779053] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [448.779128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [448.779564] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [448.779604] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [448.780083] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [448.780328] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [448.780548] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [448.780923] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [448.781150] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<7> [448.875691] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [448.876376] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [448.877403] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [448.877791] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [448.878382] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [448.878765] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [448.879551] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [448.879713] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [448.879894] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [448.882240] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [448.882812] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [448.883407] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [448.883998] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [448.884552] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [448.885167] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [448.885716] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [448.886254] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [448.886776] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [448.887335] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [448.887815] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [448.888298] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [448.888695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [448.889151] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [448.889521] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [448.889858] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [448.890240] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [448.890550] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [448.890872] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [448.891163] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [448.891427] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [448.891682] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [448.891987] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [448.892223] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [448.892449] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [448.892687] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [448.892917] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [448.893124] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [448.893319] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [448.893511] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [448.893695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [448.893890] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [448.894074] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [448.894248] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [448.894416] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [448.894577] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [448.894731] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [448.894912] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [448.895068] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [448.895216] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [448.895356] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [448.895492] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [448.895625] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [448.895763] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [448.896002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [448.896135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [448.896298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [448.896397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [448.896491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [448.896580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [448.896669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [448.896754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [448.896878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [448.897013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [448.897140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [448.897261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [448.897379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [448.897491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [448.897601] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [448.897736] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [448.897851] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [448.897958] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [448.898064] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [448.898195] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [448.898290] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [448.898387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [448.898485] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [448.898588] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [448.898689] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [448.898790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [448.898902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [448.898988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [448.899074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [448.899160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [448.899241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [448.899320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [448.899398] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [448.899477] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [448.899555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [448.899634] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [448.899715] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [448.899793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [448.899886] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [448.899967] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [448.900044] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [448.900119] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [448.900192] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [448.900265] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [448.900344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [448.900423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [448.900501] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [448.900581] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [448.900660] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [448.900738] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [448.900816] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [448.900923] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [448.901016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [448.901090] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [448.901160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [448.901230] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [448.901300] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [448.901370] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [448.901439] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [448.901508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [448.901576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [448.901647] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [448.901724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [448.901799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [448.901887] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [448.901972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [448.902048] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [448.902123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [448.902200] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [448.902288] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902457] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [448.902611] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [448.902689] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902767] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902851] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [448.902926] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [448.903008] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [448.903085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:429] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [448.903164] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [448.903240] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [448.903316] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [448.903393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [448.903469] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [448.903544] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [448.903618] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [448.905975] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [448.906221] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [448.906340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [448.906459] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [448.906550] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [448.906637] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [448.906710] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [448.906790] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [448.906869] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [448.906942] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [448.907018] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [448.907086] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [448.907152] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [448.907217] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [448.907281] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [448.907344] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [448.907407] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [448.907469] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [448.907542] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [448.907615] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [448.907708] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [448.907877] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [448.907936] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [448.908026] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [448.908950] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [448.909069] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [448.910523] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [448.910609] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [448.910714] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [448.920915] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [448.921052] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [448.921154] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [448.957283] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [448.957894] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [448.958392] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [448.959105] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [449.130082] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [449.130546] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [449.131012] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [449.133253] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [449.134927] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [449.135940] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [449.137301] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [449.138858] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [449.140053] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [449.140439] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [449.142136] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [449.142643] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [449.143635] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [449.144310] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [449.144775] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [449.145389] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 4518
<7> [449.161198] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [449.163164] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [449.163670] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [449.167131] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [449.167760] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [449.168433] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<6> [449.169137] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [449.169542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [449.170143] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [449.170536] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:429] from all active usage due to RMFB ioctl
<7> [449.170562] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [449.171079] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [449.171507] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [449.171995] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [449.172551] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:429] is removed
<7> [449.172746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [449.173201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [449.173511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [449.173776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [449.174110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [449.174401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [449.174752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [449.175347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [449.175667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [449.175968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [449.176250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [449.177187] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [449.177691] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [449.178018] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [449.196423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [449.196926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [449.197363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [449.197750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [449.198164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [449.198526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [449.199013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [449.199424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [449.199809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [449.200226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [449.200575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [449.211063] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [449.213340] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [449.214414] [IGT] kms_pm_rpm: exiting, ret=0
<6> [449.228941] Console: switching to colour frame buffer device 180x56
<7> [449.246001] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [449.246562] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [449.247099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [449.247728] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [449.248374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [449.279994] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [449.280555] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [449.281087] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2026-02-19 19:48:47