Result:
i915_display_info4 igt_runner4 results4.json results4-xe-load.json guc_logs4.tar i915_display_info_post_exec4 boot4 dmesg4
| Detail | Value |
|---|---|
| Duration | 0.00 seconds |
| Hostname |
shard-lnl-1 |
| Igt-Version |
IGT-Version: 2.3-g2020b0bf9 (x86_64) (Linux: 6.19.0-lgci-xe-xe-4576-cc2c646d39200973c-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1771527718 for randomisation Opened device: /dev/dri/card0 Test requirement not met in function chamelium_init_test, file ../tests/chamelium/kms_chamelium_helper.c:49: Test requirement: data->chamelium Subtest dp-edid-stress-resolution-non-4k: SKIP (0.000s) |
| Err |
Subtest dp-edid-stress-resolution-non-4k: SKIP (0.000s) |
| Dmesg |
<6> [425.619268] Console: switching to colour dummy device 80x25
<6> [425.619529] [IGT] kms_chamelium_edid: executing
<7> [425.624466] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [425.624474] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [425.624623] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [425.624833] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [425.624835] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [425.624948] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [425.625206] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [425.625209] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [425.625347] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [425.625600] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]
<7> [425.625602] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]
<7> [425.626041] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [425.626375] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [425.626482] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [425.626588] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [425.626741] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [425.626747] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.626750] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.626751] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [425.626755] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [425.626758] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.626760] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor
<5> [425.626764] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.626766] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0
<5> [425.626769] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.626781] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes
<7> [425.626894] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [425.627010] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [425.627584] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.627587] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.627588] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.627665] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:
<7> [425.627667] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [425.627670] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [425.627683] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [425.627685] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [425.627833] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [425.627843] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [425.627846] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [425.627965] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [425.627972] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [425.627974] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [425.628086] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [425.629069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [425.629182] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [425.629278] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [425.629385] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [425.629490] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [425.629578] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [425.629665] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [425.629751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [425.629837] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [425.629922] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [425.630007] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [425.630098] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [425.630199] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [425.630296] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [425.630393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [425.630489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [425.630571] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [425.630652] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [425.630726] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [425.630808] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [425.630891] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [425.630971] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [425.631051] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [425.631143] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [425.631239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [425.631334] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [425.631416] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [425.631489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [425.631564] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [425.631639] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [425.631717] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [425.631797] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [425.631875] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [425.631951] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [425.632024] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [425.632196] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [425.632290] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [425.632383] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [425.632474] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [425.632552] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [425.632664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [425.632737] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [425.632810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [425.632880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [425.632946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [425.633003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.633073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.633145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.633232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [425.633334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [425.633426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [425.633510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [425.633591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [425.633671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [425.633752] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [425.633844] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 43464 kHz -> 0 kHz
<7> [425.633937] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [425.634034] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [425.634150] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [425.634270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [425.634365] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [425.634449] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [425.634533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [425.634616] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [425.634695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [425.634776] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [425.634910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [425.635007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [425.635154] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [425.638407] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [425.638515] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [425.844213] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [425.844639] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [425.864979] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [425.865399] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [425.865522] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [425.865838] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [425.865890] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [425.917085] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [425.917412] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [425.917522] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [425.918264] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [425.918636] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [425.918770] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [425.918990] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [425.919121] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [425.919480] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [425.919699] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [425.919898] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [425.920124] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [425.920317] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [425.920508] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [425.920749] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [425.920950] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [425.921186] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [425.921370] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [425.921546] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [425.921719] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [425.921921] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [425.922118] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [425.922306] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:401:DP-1]
<7> [425.922497] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:413:DP-2]
<7> [425.922688] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:421:DP-3]
<7> [425.922936] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [425.923151] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [425.923331] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [425.923671] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [425.923903] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [425.924231] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [425.924463] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [425.924742] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [425.924946] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [425.925245] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800010 0x9a00071)
<6> [425.927124] [IGT] kms_chamelium_edid: exiting, ret=77
<6> [425.928814] Console: switching to colour frame buffer device 180x56
<7> [425.935459] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [425.935628] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [425.935755] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [425.935885] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [425.936003] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [425.936144] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [425.936257] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [425.936367] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [425.936475] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [425.936582] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [425.936686] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [425.936787] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [425.936886] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [425.936982] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [425.937094] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [425.937199] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [425.937302] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [425.937389] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [425.937473] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [425.937564] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [425.937663] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [425.937760] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [425.937845] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [425.937920] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [425.937996] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [425.938096] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [425.938191] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [425.938284] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [425.938367] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [425.938444] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [425.938521] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [425.938598] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [425.938674] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [425.938751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [425.938825] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [425.938901] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [425.938977] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [425.939068] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [425.939161] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [425.939253] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [425.939345] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [425.939436] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [425.939519] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [425.939595] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [425.939708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [425.939783] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [425.939860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [425.939930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [425.939997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [425.940079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [425.940154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [425.940234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [425.940333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [425.940426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [425.940517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [425.940603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [425.940688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [425.940768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [425.940865] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [425.940982] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [425.941102] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [425.941202] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [425.941302] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [425.941402] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [425.941478] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [425.941560] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [425.941643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [425.941723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [425.941801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [425.941875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [425.941948] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [425.942026] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [425.942119] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [425.942216] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [425.942312] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [425.942389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [425.942462] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [425.942534] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [425.942622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [425.942715] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [425.942809] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [425.942890] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [425.942967] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [425.943069] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [425.943161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [425.943230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [425.943260] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [425.943353] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [425.943352] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [425.943438] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [425.943531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [425.943626] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [425.943719] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [425.943804] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [425.943875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [425.943945] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [425.944019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [425.944156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [425.944265] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [425.944355] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [425.944442] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [425.944521] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [425.944611] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [425.944707] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [425.944797] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [425.944886] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [425.944961] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [425.945042] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [425.945137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [425.945238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [425.945337] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [425.945418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [425.945497] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [425.945573] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [425.945646] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [425.945718] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [425.945791] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.945864] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.945933] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.946000] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [425.946107] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [425.946199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.946291] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.946367] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [425.946443] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [425.946532] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [425.946617] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [425.946705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [425.946782] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [425.946854] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [425.946922] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [425.946992] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [425.947106] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [425.947205] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [425.948068] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [425.948396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [425.948547] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [425.948688] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [425.948821] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072)
<7> [425.948918] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [425.949030] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [425.949142] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [425.949246] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [425.949333] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [425.949401] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [425.949490] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [425.949563] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [425.949635] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [425.949706] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [425.949779] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [425.949854] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [425.949936] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [425.950017] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [425.950115] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [425.950195] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [425.950295] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [425.950462] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [425.950534] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [425.950643] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [425.951961] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [425.952067] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [425.953992] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [425.954094] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (464 ms remaining)
<7> [425.955843] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [425.955990] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [425.956088] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [425.956187] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [426.420207] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [426.491648] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [426.492068] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [426.492348] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [426.528589] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [426.529066] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [426.529452] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [426.529842] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [426.645179] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [426.645187] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [426.645314] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [426.703749] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [426.704247] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [426.704600] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [426.706732] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [426.708286] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [426.709057] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [426.710159] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [426.711466] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [426.712523] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [426.712850] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [426.714279] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [426.714591] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [426.715395] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [426.715819] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [426.716233] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [426.716648] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 4518
<7> [426.732701] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.734378] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [426.734742] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [426.738204] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
|