igt@kms_rotation_crc@multiplane-rotation-cropping-top on shard-lnl@IGT

Detail	Value
Duration	10.64 seconds
Hostname	shard-lnl-7
Igt-Version	IGT-Version: 2.3-g829d402dc (x86_64) (Linux: 6.19.0-rc1-lgci-xe-xe-4265-31985bb0a701138a0+ x86_64)
Out	Using IGT_SRANDOM=1766130474 for randomisation Opened device: /dev/dri/card0 Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.645s)
Err	Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (10.645s)
Dmesg	<6> [136.050528] Console: switching to colour dummy device 80x25 <6> [136.050715] [IGT] kms_rotation_crc: executing <7> [136.055626] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [136.055635] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [136.055783] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [136.055995] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [136.055997] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [136.056138] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [136.056398] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [136.056401] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [136.056520] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <7> [136.056770] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] <7> [136.056773] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1] <7> [136.057212] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [136.057527] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [136.057634] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [136.057738] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [136.057856] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [136.057860] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [136.057862] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [136.057863] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7> [136.057865] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [136.057866] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [136.057868] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor <5> [136.057870] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [136.057871] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0 <5> [136.057872] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [136.057884] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes <7> [136.057969] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [136.058109] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [136.058763] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [136.058765] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [136.058766] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [136.058818] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes: <7> [136.058822] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [136.058825] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [136.058841] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [136.058844] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1] <7> [136.058983] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [136.058993] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] <7> [136.058995] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2] <7> [136.059130] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected <7> [136.059137] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] <7> [136.059139] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3] <7> [136.059242] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected <6> [136.059435] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top <7> [136.060735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0 <7> [136.060810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [136.060875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [136.060939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [136.061001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [136.061111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [136.061237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [136.061359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [136.061454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [136.061543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [136.061631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [136.061917] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.062026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.062179] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [136.069966] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [136.070213] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [136.070404] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [136.070504] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [136.070587] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [136.070670] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation <7> [136.070745] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [136.070829] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [136.070935] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [136.071019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [136.071137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [136.071243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [136.071345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [136.071432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [136.071516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [136.071600] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [136.071684] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [136.071766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [136.071847] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [136.071921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [136.071996] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [136.072085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [136.072187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8 <7> [136.072287] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [136.072382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [136.072463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [136.072546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [136.072641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [136.072736] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [136.072829] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [136.072911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [136.072988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [136.073072] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [136.073173] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [136.073278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [136.073377] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [136.073454] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [136.073529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [136.073604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [136.073679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [136.073753] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [136.073828] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [136.073898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [136.073969] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [136.074043] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [136.074164] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [136.074253] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [136.074341] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [136.074429] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [136.074517] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [136.074605] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [136.074693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [136.074778] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [136.074852] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [136.074939] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [136.075026] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075306] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [136.075383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [136.075450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075519] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075589] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [136.075659] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [136.075728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [136.086372] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [136.086504] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [136.106122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.106423] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.106645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.137494] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427] <7> [136.138882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [136.139296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [136.139603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.139880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.140203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.140467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.140752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.141059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.141313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.141584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.141899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.142332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.142770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.143215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.143555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.143892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.144947] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.145341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.146331] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [136.146598] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [136.152896] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1 <7> [136.155662] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430] <7> [136.187212] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.187759] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.188260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.188948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431] <7> [136.189849] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.190292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.190598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.190948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.191311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.191597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.191926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.192535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.192812] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.193076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.193374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.193620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.193862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.194532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.194982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.195390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.195799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.196127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.196470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.196820] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz <7> [136.197502] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.197790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.220082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.220462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.220771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.220974] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432] <7> [136.221777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [136.222022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [136.222344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.222554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.222759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.222997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.223298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.223730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [136.223937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [136.224175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.224411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.224604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.224792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.224986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.225323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.225650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.225927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.226229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.226550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.227378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.227688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.254143] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433] <7> [136.254093] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.254509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.254860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.254927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.255244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.255481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.255704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.255932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.256268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.256564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.257054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.257281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.257478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.257672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.257863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.258158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.258399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.258905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.259208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.259395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.259620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.259821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.260006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.260266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.260570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.260871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.261240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.261609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.261905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.262858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.263177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.287159] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.287411] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434] <7> [136.287546] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.287832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.301927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [136.302217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [136.302429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.302618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.302799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.302984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.303220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.303554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [136.303706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [136.303852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.303988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.304157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.304288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.304419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.304693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [136.304840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [136.304977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.305321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.305431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.305536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.305641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.305806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.305967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.306169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.306325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.306474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.306942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.307151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.336875] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435] <7> [136.337081] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.337556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.337981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.353160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [136.353422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [136.353643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.353846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.354063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [136.354250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [136.354498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.354776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.355048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.355302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.355556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.355814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.356756] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.357021] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.386805] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436] <7> [136.387542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [136.387811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [136.388118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.388104] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.388362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.388471] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.388596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.388794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.388877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.389205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.389573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.389941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.390438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.390819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.391190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.392126] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.392487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.404188] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437] <7> [136.437139] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438] <7> [136.437139] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.437562] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.437918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.438102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.438365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.438603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.438831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.439095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.439319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.439624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.439978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.440380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.440700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.441015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.441436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.442219] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.442536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.470122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.470534] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.470707] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439] <7> [136.470853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.471471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [136.471675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [136.471855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.472049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.472224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.472424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.472616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.472870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.473169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.473436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.473712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.473999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.474811] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.475145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.503833] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440] <7> [136.504128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.504511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.504586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [136.504793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [136.504829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.504984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.505281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.505469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.505691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.505933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.506268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.506562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.506849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.507168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.507429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.508320] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.508584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.537068] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.537446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.537600] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441] <7> [136.537752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.550329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [136.550572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [136.550784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.551000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.551396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.551669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.551905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [136.552272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [136.552542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [136.552790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.553040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [136.553315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [136.553973] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.554394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.587163] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442] <7> [136.587113] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.587479] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.587836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.604308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [136.604577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [136.604805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.605056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.605264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [136.605514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [136.605759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.606199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.606436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.606659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.606873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.607150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.607921] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.608142] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.636657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [136.637049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [136.637392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.637722] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.637968] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.638143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.638442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.638466] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.638719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.638875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.638993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.639351] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.639635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.640556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.640957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.686512] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.686817] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.687182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.687204] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.687424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.687650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.687619] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.687907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.687971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.688197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.688535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [136.688861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [136.689214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.689577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.689931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [136.690822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.691146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.719957] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443] <7> [136.720867] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [136.721130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [136.721162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.721336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.721574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.721549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.721787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.721892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.722068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.722319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.722639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.722942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.723395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.723680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.723986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.725031] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.725356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.753126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.753326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.753511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.753696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.753887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.754181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.754147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.754452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.754499] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.754784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [136.754821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.755111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [136.755458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.755759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.756108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [136.757169] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.757522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.786652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [136.786865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [136.787109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.787117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.787306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.787432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.787503] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.787679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.787712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.787888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.788369] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [136.788564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [136.788751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.788937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.789173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.789397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.789589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.789898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.790252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.790623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.790977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.791390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.792268] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.792610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.819786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [136.820040] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.820058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [136.820250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.820285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.820432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.820504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.820608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [136.820797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [136.821016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.821390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [136.821569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [136.821740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.821913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.822133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [136.822308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [136.822492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.822768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [136.823081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [136.823420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.823710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.824018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [136.825125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.825461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.853168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [136.853443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [136.853675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.853891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.854179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.854199] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.854401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.854511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.854700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.854800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.855184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [136.855406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [136.855627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.855883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.856135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.856339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.856602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.857090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [136.857315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [136.857511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.857703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.857897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.858143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.858376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.858714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.859096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.859430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.859766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.860102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.860941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.861255] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.886455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.886725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.886963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.887279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.887296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.887507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.887624] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.887765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.887934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.888023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.888513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.888750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.888959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.889223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.889430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.889677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.889914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.890455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.890679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.890893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.891222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.891417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.891629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.891847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.892202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [136.892494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [136.892783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.893063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.893346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [136.894082] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.894341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.919801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [136.920119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.920189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [136.920427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.920427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.920649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [136.920712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.920865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [136.921192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [136.921446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.921794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.922150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.922473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.922845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.923258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.924207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.924514] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.953093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [136.953297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [136.953489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.953677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [136.953869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [136.954130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [136.954141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.954369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [136.954467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.954690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [136.954760] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.955075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [136.955422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.955758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [136.956164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [136.957185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.957537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [136.986519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [136.986697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [136.986858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [136.987119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [136.987092] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [136.987278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [136.987333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [136.987432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [136.987552] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [136.987604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [136.987841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [136.988120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [136.988417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.988660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [136.988964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [136.989744] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [136.990060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.019720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [137.019940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [137.020202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.020207] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.020395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.020498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.020581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.020763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.020763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.020995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [137.021362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.021732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.022049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.022411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.022766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.023846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.024256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.054050] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444] <7> [137.055023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.055341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.055452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.055633] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.055762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [137.056111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [137.056355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [137.056591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.056821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.057120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.057349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.057573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.057841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [137.058111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [137.058348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [137.058558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.058762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.058969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.059250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.059495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.059849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.060228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.060611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.060988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.061374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.062523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.062917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.069390] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [137.088269] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445] <7> [137.089739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.118030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.118399] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.119647] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.119759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.120054] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [137.120044] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [137.120045] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [137.120189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.120528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.120792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.121089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.121392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.121641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.121880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.122177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.122513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.122840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.123196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.123521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.123846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.124708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.125251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.153116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.153473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [137.153731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [137.154001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [137.154036] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.154227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.154497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.154445] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.154717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.154802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.154933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.155246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.155637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.155948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.156349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.156690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.157000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.158163] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.158464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.186360] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.186712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.187013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.187117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.187233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.187441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.187498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.187643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.187848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.187825] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.188166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.188419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.188743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.189052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.189403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.189689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.189997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.190877] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.191230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.219872] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.220175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [137.220228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.220429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [137.220624] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [137.220606] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.220812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.220935] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.221025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.221203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [137.221377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [137.222069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.222333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.222586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.222838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.223165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.223420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.224102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.224360] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.253076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.253418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [137.253726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [137.254016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [137.254108] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.254243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.254511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.254553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.254738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.254934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.255015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.255243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.255562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.255864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.256181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.256465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.256743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.257578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.257865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.286335] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.286620] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [137.286834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [137.287071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [137.287170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.287247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.287415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.287484] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.287581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.287771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.287747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.288006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.288406] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.288616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [137.288787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [137.288941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [137.289140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.289294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.289446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.289595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.289752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.290009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.290311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.290562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.290851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.291127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.291771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.292036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.303084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.336337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.336643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.336910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.337248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.337377] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.337486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.337716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.337787] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.337947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.338198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.338299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.338565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.339027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.339271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.339467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.339659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.339850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.340145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.340358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.340617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.340867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.341258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.341580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.341879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.342252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.342587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.343285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.343564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.369662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.370009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [137.370122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.370253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [137.370460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [137.370475] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.370655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.370779] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.370883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.371106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.371278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.371512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.371986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.372183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [137.372339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [137.372491] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [137.372640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.372786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.372941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.373162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.373344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.373638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.373907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.374173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.374404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.374650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.375584] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.375852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.403012] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.403336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.403571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.403786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.404058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.404083] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.404282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.404436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.404504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.404772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.404752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.405035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.405539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.405776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [137.405978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [137.406158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [137.406334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.406542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.406732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.406926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.407156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.407414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.407671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.407928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.408221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.408522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.409248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.409515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.436484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.436798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [137.437093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [137.437208] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.437291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [137.437480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.437539] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.437661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.437838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [137.437823] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.438085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [137.438290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [137.438538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [137.438787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [137.439088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.439345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [137.439648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [137.440377] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.440629] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.469670] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.470009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [137.470098] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.470270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [137.470488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [137.470509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.470699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.470861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.470994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.471208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.471463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.471699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [137.472043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [137.472394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [137.472764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.473107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [137.473422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [137.474386] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.474712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.503996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.504412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.504671] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446] <7> [137.504765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.506812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.507182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [137.507428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [137.507657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [137.507880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.508136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.508340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.508578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.508768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.508959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.509138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.509312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.509484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.509652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.509821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.510052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.510251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.510515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.510772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.511063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.511314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.511557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.512363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.512631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.520914] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447] <7> [137.521838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.552906] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.553234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.553480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.553687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.553886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.554141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.554252] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.554328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.554525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.554585] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.554730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.554871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.555035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.555305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.555566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.555822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.556128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.556765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.557062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.586307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.586609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [137.586879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [137.587177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [137.587284] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.587399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.587663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.587692] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.587886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.588075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.588157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.588376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.588669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.588957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.589236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.589502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.589801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.590898] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.591232] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.619583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.619851] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.620138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.620324] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.620264] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.620505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.620620] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.620720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.620908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.620924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.621161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.621344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.621599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.621848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.622125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.622358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.622588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.623275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.623532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.653060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.653284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [137.653450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [137.653610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [137.653795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.653998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.654023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.654164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [137.654327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [137.654356] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.654511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.654639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.654768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.655016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.655296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.655535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.655764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.656499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.656765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.686217] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.686486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [137.686689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [137.686880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [137.687158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.687335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.687280] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.687510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.687637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.687717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.687970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.687976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.688233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.688485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.688737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.689002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.689284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.689920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.690228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.719612] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.719896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [137.720193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [137.720404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [137.720336] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.720610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.720807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.720745] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.721032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.721110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.721234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.721473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.721768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.722120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.722484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.722844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.723211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.724055] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.724354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.736635] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.769524] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.769750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.769921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.770200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.770288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.770369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.770542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.770621] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.770708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.770870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.770911] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.771090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.771498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.771689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.771839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.772028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.772184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.772370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.772523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.772674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.772830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.773100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.773332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.773564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.773838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.774130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.774771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.775036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.803002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.803306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [137.803559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [137.803765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [137.803994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.804174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.804122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.804353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.804454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.804561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.804739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.804754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.805222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.805431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [137.805597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [137.805759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [137.805917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.806129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.806324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.806508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.806670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.806940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.807198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.807450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.807695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.807971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.808941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.809207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.836327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.836655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.836887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.837161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.837304] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.837358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.837594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.837661] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.837800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.838074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.838037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.838299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.838717] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.838981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [137.839176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [137.839372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [137.839558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.839771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.839973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.840141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.840314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.840590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.840873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.841212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.841556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.841838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.842669] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.842956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.869902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.870353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [137.870440] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.870694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [137.870886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.870991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [137.871245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.871345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.871492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.871738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [137.872037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [137.872284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.872849] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.873194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [137.873496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [137.873734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [137.874022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.874254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.874482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [137.874710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [137.874947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [137.875268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [137.875587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [137.875982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.876290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [137.876569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [137.877359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.877642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.902999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.903422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [137.903768] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [137.904127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [137.904266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.904406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.904730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.904748] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.905079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.905211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.905330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.905595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.906200] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [137.906499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [137.906763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [137.907029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [137.907262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.907494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [137.907717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [137.907955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [137.908192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [137.908536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [137.908877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [137.909252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.909622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [137.909954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [137.910870] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.911197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.936377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [137.936698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [137.937036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [137.937180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.937298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.937553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.937632] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.937841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.938038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.938117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.938358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [137.938603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [137.938842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [137.939100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [137.939311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.939514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [137.939714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [137.939935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [137.940168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [137.940498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [137.940815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [137.941222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [137.941561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [137.941877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [137.942759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.943072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [137.943739] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [137.943975] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [137.969521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [137.969735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [137.969948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [137.970067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [137.970130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [137.970292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [137.970371] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [137.970479] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [137.970626] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [137.970675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [137.970933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [137.971156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [137.971371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [137.971605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [137.971808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [137.972364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [137.972557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.004015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448] <7> [138.004004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.004457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.004838] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.005044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [138.005315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [138.005565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.005808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.006077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.006306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.006545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [138.006868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [138.007245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [138.007558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.007904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.008275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [138.009123] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.009452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.036267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [138.036543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [138.036774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.037080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.037174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.037311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.037590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.037586] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.037839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.037965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.038178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.038479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.038811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.039135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.039472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.040468] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.040773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.069789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [138.070125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [138.070267] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.070362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.070587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.070648] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.070803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.071047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.071139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.071394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [138.071733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [138.072097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [138.072420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.072792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.073153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [138.073996] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.074305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.102872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [138.103161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [138.103375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.103636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.103851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.104158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.104290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.104395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.104701] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.104717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.105099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.105073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.105446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.105752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.106148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.106981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.107279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.136245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [138.136482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [138.136672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.136859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.137120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.137313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.137259] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.137568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [138.137638] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.137865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [138.137993] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.138186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [138.138503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.138783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.139061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [138.139661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.139925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.169523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [138.169726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [138.169956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.170165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.170100] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.170365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.170511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.170606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.170870] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.170871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.171269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.171579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.172190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.172496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.172792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.173782] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.174138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.202942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [138.203051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.203150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [138.203338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.203431] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.203520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.203698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.203757] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.203953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.204175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [138.204492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [138.204800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [138.205123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.205459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.205733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [138.206450] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.206723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.236188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [138.236394] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [138.236602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.236834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.237086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.237265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.237226] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.237469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.237611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.237757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.237971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.238120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.238403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.238660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.238911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.239605] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.239856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.269734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [138.269999] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [138.270210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.270143] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.270457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.270550] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.270663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.270868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.270956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.271186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [138.271599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [138.271960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [138.272295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.272628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [138.273173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [138.274061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.274373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.302845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [138.303099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [138.303185] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.303279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.303498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.303566] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.303682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.303859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.303939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.304146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.304587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [138.304778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [138.305048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.305230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.305411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.305614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.305831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.306163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.306450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.306739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.307132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.307446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.308263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.308560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.336264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [138.336516] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [138.336732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.336973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.337003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.337161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.337336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.337379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.337566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.337621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.337736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.337932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.338090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.338371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [138.338522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [138.338671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.338822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.339024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.339181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.339336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.339491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.339642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.339795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.340556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.340836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.386186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.386465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.386699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.386967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.387110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.387201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.387439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.387523] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.387693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.387875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.388207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.388426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.388637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.388841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.389117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.389340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.389585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.390054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.390257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.390453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.390647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.390843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.391100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.391346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.391670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.391991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.392279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.392568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.392869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.393687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.394016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.419937] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.420395] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.420748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.421531] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449] <7> [138.422340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [138.422628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [138.422907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.423149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.423410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.423676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.424038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.424535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [138.424758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [138.425013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.425261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.425476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.425682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.425910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.426340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [138.426567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [138.426751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.427025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.427198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.427372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.427551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.427810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.428098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.428367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.428602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.428831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.429553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.429775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.452847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.453307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.453393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.453564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.453799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.453801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.454084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.454214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.454331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.454610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.455024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.455353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.455675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.456057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.456372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.457270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.457605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.486404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [138.486675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [138.486969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.487116] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.487213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.487451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.487534] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.487716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.487931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.488016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.488387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.488747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.489211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.489560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.489917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.490847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.491272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.519416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [138.519654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [138.519857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.520138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.520235] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.520315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.520493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.520549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.520682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.520821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.520952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.521216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.521471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.521771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.522061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.522721] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.523003] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.552807] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [138.553069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [138.553163] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.553261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.553488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.553551] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.553685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.553906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.553910] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.554105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.554379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.554648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.554939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.555234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.555495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.556158] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.556434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.586139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.586396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.586591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.586819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.587097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.587305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.587234] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.587589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.587644] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.587916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.588008] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.588206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.588498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.588798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.589118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.589847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.590151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.619439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [138.619626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [138.619798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.620040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.620119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.620213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.620410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.620472] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.620603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.620776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.620892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.621148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.621396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.621691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.621936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.622556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.622797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.652795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [138.653063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [138.653148] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.653253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.653433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.653528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.653616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.653830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.653853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.654162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.654438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.654701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.655048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.655318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.655572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.656304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.656576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.686309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [138.686504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [138.686683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.687061] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.687181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.687375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.687446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.687574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.687772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.687875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [138.688150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [138.688418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [138.688706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.689025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [138.689335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [138.690106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.690385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.716924] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off <7> [138.717153] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [138.719348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [138.719533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [138.719699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.719927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.720018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.720099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.720253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.720329] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.720420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [138.720594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.720659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [138.720918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [138.721167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.721409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [138.721651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [138.722390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.722669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.753145] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.753481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.753762] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.753969] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450] <7> [138.755502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.755747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [138.755989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [138.756160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [138.756326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.756487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.756680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.756863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.757023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.757177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [138.757369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [138.757549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [138.757717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.757892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.758049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.758202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.758381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.758637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [138.758901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [138.759205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.759451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.759748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [138.760794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.761086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.769076] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [138.787711] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451] <7> [138.789684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.819370] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.819678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [138.820010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [138.820137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.820258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [138.820496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.820552] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.820730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.820953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.821016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.821325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.821636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [138.822073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [138.822439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [138.822793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.823205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.823546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [138.824479] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.824889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.852812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.853196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [138.853241] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.853438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [138.853660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [138.853620] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.853963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.853969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.854176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.854383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.854632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.854892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.855325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.855567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [138.855802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [138.856053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [138.856281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.856482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.856662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.856906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.857129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.857425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [138.857719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [138.858034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.858307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.858572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [138.859419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.859704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.886175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.886531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [138.886820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [138.887151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [138.887267] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.887394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.887620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.887675] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.887862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.888100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.888081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.888347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [138.888815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.889131] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [138.889350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [138.889561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [138.889817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.890086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [138.890342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [138.890567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [138.890780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [138.891137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [138.891454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [138.891767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.892096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.892379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [138.893244] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.893518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.919960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.920010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.920348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [138.920460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.920685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [138.920894] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.921026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [138.921290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.921539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.921777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.922077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.922318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.922774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.923073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [138.923283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [138.923486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [138.923685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.923909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.924108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [138.924303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [138.924527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.924871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [138.925231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [138.925549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.925880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.926185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [138.927065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.927375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.952769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.953184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [138.953285] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.953471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [138.953715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [138.953694] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.954001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.954094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.954231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.954456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.954730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.955042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [138.955592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.955863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [138.956115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [138.956323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [138.956512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.956717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [138.956947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [138.957148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [138.957377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [138.957710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [138.958048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [138.958338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.958624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [138.958912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [138.959730] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.960039] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [138.986105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.986412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [138.986689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [138.986955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [138.987084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [138.987169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.987420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.987462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [138.987632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.987790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [138.987875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.988101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.988643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [138.989341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [138.989538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [138.989725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [138.989961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [138.990144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [138.990326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [138.990504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [138.990691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [138.991028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [138.991326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [138.991652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.991961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [138.992295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [138.993324] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [138.993612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.002812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.036980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.037152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.037242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.037353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [139.037425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.037497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [139.037610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [139.037719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.037823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.037977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.038078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.038207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [139.038350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [139.038487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [139.038617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.038743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.038885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [139.039341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.039478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.069197] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.069325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [139.069399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [139.069460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [139.069520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.069578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.069635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.069691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.069756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [139.069867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [139.069881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.069987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [139.070040] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.070096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [139.070167] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.070202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [139.070306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [139.070648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.070748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.102762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.103142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [139.103228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.103405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [139.103611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [139.103622] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.103813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.104002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.104077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.104261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.104438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.104647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [139.104988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [139.105247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [139.105501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.105797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.106088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [139.106804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.107241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.136288] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.136563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [139.136771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [139.137045] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [139.137142] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.137230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.137449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.137498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.137653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.137805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.137893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.138098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [139.138389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [139.138642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [139.138910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [139.139217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [139.139469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [139.140272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.140531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.169351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.169680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [139.170001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [139.170091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.170209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [139.170403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.170446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.170592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.170746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.170780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [139.171053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [139.171257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [139.171519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [139.171778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [139.172061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.172362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [139.172615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [139.173353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.173612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.202965] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.203303] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.203590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.204127] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452] <7> [139.205866] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.206135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [139.206326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [139.206501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [139.206668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.206859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.207035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.207214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.207381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.207544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.207706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.207892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.208041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.208185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.208330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.208473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.208644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.208903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.209164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.209420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.209669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.209945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.210800] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.211104] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.220301] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453] <7> [139.221244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.252716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.253122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [139.253206] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.253437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [139.253619] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.253685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [139.253971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.254005] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.254238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.254453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.254686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.254968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.255303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.255635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.256059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.256365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.256668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.257439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.257734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.286065] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.286372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [139.286594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [139.286795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [139.287115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.287225] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.287325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.287527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.287604] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.287734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.287974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.288002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.288309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.288611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.288930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.289274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.289562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.290439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.290749] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.319325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.319659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [139.319973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [139.320028] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.320216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [139.320448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.320443] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.320666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.320796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.320919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.321138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.321381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.321686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.322000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.322270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.322535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.322884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.323750] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.324068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.352873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.352957] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.353103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [139.353271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [139.353289] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.353436] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [139.353599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.353569] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.353794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.354018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.354180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.354356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.354689] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.354911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [139.355068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [139.355219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [139.355369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.355516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.355663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.355805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.356017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.356253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.356488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.356728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.357000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.357278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.357961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.358206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.386112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.386442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [139.386680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [139.386969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [139.387003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.387203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.387429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.387411] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.387650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [139.387765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.387954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [139.388197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.388681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.388988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [139.389196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [139.389397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [139.389628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.389853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.390049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [139.390242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [139.390443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.390763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.391136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.391502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.391841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.392125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.392889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.393191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.419553] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.420030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [139.420103] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.420357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [139.420646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [139.420590] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.420978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.421066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.421250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.421517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.421857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.422121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.422643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.422963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [139.423193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [139.423416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [139.423644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.423912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.424177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.424393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.424614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.425000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.425407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.425739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.426093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.426401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.427405] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.427689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.436074] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.469285] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.469575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [139.469792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [139.470093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [139.470228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.470312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.470523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.470609] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.470734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.470976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.471045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.471257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.471725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.471968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [139.472142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [139.472311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [139.472514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.472695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.472903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.473122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.473328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.473607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.473911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.474231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.474521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.474827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.475555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.475839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.502666] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.502991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [139.503081] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.503216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [139.503409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [139.503415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.503594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.503700] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.503773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.504023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.504196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.504380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.504628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.504888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.505150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.505414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.505661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.506392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.506644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.535918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.536139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [139.536317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [139.536474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [139.536627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.536778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.537004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.537038] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.537167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.537345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.537372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.537601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.537656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.537864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.538144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.538381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.538607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.539355] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.539612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.569513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.569842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [139.569975] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.570123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [139.570344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [139.570421] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.570593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.570825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.570842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.571041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.571272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.571557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [139.572012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [139.572407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [139.572817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.573178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [139.573509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [139.574427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.574768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.602622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [139.602967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [139.602995] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.603269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [139.603372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.603489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [139.603700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.603697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.603965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.604155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [139.604340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [139.604544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [139.604894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [139.605153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [139.605407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.605674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [139.605946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [139.606666] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.606949] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.636187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [139.636449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [139.636689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [139.637032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.637164] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.637268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.637517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.637611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.637771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.638063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [139.638065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.638282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [139.638496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [139.638704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [139.638958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.639145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.639338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.639544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.639780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.640163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.640504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.640837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.641142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.641476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.642470] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.642815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.643715] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [139.644011] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [139.669305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.669582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.669864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.669986] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.670103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.670334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.670397] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.670607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.670750] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.670889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.671255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [139.671613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [139.671984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.672371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.672726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [139.673612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.673995] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.703766] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454] <7> [139.703830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.704333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.704721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.720622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [139.720965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [139.721211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.721445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.721671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.721972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.722219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.722531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.722990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.723257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.723510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.723760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.724681] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.724945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.752667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.752984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.752941] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.753190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.753380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.753326] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.753581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.753658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.753838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.754076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.754400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [139.754717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [139.755150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.755515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.755872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [139.756926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.757315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.786267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [139.786542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [139.786776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.787050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.787168] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.787253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.787486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.787521] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.787735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.787854] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.788057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.788337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.788609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.788955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.789229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.789952] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.790236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.819223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [139.819433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [139.819623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.819858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.819982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.820073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [139.820267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [139.820364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.820485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.820690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.821220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [139.821520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [139.821822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.822136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.822440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [139.823320] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.823623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.852680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [139.852984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [139.853096] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.853205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.853458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.853509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.853678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.853947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.853902] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.854176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.854497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.854821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.855200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.855504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.855823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.856562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.856918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.885929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.886128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.886312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.886496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.886724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.886985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.887110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.887217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.887490] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.887657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.887877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.887844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.888042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.888205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.888365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.888523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.888686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.888993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [139.889258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [139.889545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.889823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.890082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [139.890754] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.891068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.919293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [139.919531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [139.919731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.919976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.920097] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.920154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.920358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.920415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.920570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.920682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.920964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [139.921142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [139.921308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.921508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [139.921690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [139.921908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [139.922067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.922309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.922549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.922801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.923112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.923363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.924051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.924300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.952578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.952871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.952991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.953105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.953378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.953400] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.953595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.953751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.953877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.954134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.954653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.954923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.955148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.955387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.955629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.955932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.956175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.956681] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [139.957008] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [139.957227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.957481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [139.957694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [139.957962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [139.958183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [139.958526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [139.958875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [139.959241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.959601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [139.959949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [139.960844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.961135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [139.986226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [139.986522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [139.986813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.986932] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [139.987034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.987245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.987311] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [139.987468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.987636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [139.987702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.988221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [139.988441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [139.988649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.988892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.989104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.989343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.989558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.990012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [139.990202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [139.990382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [139.990559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [139.990738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [139.990967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [139.991140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [139.991408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [139.991678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [139.991972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.992222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [139.992466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [139.993185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [139.993420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.019240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [140.019539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [140.019839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.019948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.020084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.020315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.020359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.020594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.020718] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.020904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.021297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.021629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.021985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.022279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.022570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.023427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.023731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.052612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [140.052893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [140.053104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.053035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.053360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.053446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.053574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.053823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.053843] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.054047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.054266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.054482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.054695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.055599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.056037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.102679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [140.103040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [140.103271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.103487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.103694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.104006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.104115] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.104262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.104556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.104597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.104970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.104976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.105300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.105615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.106111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.107007] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.107346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.137090] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455] <7> [140.136955] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.137376] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.137751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.154012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [140.154298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [140.154522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.154732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.155011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.155200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.155453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.155721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.156036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.156265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.156487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.156723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.157343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.157552] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.185905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [140.186133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [140.186328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.186563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.186809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.186824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.187032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.187211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.187286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.187535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.187613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.187983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.188381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.188722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.189275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.190330] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.190693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.219484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [140.219896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [140.219947] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.220214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.220395] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.220472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.220726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.220816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.221083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.221341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.221733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.222114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.222436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.222772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.223111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.223977] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.224310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.252520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [140.252778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [140.252896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.252986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.253225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.253277] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.253447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.253640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.253602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.253888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.254166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.254440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.254707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.255044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.255288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.256020] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.256281] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.285884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [140.286091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [140.286315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.286510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.286695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.286939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.287052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.287141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.287417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.287408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.287689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.287711] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.288021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.288264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.288506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.289165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.289423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.319112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [140.319303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [140.319508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.319678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.319911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.320034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.320105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.320334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.320390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.320615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.320693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.320910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.321153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.321393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.321684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.322289] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.322543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.352546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [140.352782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [140.352892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.352979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.353208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.353273] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.353405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.353587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.353599] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.353817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.354108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.354459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.354787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.355071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.355345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.356141] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.356415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.385871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [140.386075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [140.386251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.386431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.386647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.386895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.386920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.387117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.387331] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.387433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.387683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.387770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.388058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.388339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.388612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.389472] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.389778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.419353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [140.419555] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [140.419777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.419973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.419890] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.420144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.420307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.420251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.420493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [140.420555] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.420780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [140.421087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [140.421357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.421597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [140.421871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [140.422542] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.422832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.452479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [140.452669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [140.452916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.452964] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.453105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.453286] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.453344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.453472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.453672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.453667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.454095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [140.454259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [140.454417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.454570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.454725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.454933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.455089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [140.455336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.455582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.455993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.456227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.456492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.457369] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.457690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.486908] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456] <7> [140.486883] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.487299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.487645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.509513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.510261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [140.510478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [140.510660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [140.510866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.511042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.511212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [140.511391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [140.511566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.511752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.511920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [140.512062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [140.512205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.512339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.512470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.512596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.512790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.513274] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.513490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [140.513633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [140.513781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [140.513915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.514041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.514165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [140.514283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [140.514389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.514490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.514588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [140.514686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [140.514822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.514942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.515047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.515152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.515280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.515465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.515636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.515806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.515953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.516101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.517018] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.517209] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.518775] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [140.537452] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457] <7> [140.553764] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.554061] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.554243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.558781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.559638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.559804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.586011] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.586418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [140.586670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [140.586936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [140.586953] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.587157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.587297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.587357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.587561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.587614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.587790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.588053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.588801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.589063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [140.589242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [140.589407] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [140.589571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.589742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.589908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.590069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.590243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.590500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.590772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.591028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.591264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.591490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.592364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.592614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.619373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.619785] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [140.620024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [140.620245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [140.620461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.620675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.620934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.620943] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.621164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.621297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.621437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.621620] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.622199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.622489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [140.622706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [140.623050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [140.623268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.623480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.623695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.623926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.624160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.624522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.624892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.625230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.625552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.625891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.627137] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.627439] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.652647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.652959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.653027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [140.653194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [140.653257] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.653350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [140.653510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.653521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.653675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.653853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.654022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.654236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.654532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.654826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.655082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.655332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.655569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.656606] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.656887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.686432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.686754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.686960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [140.687133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.687254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [140.687505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [140.687483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.687780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.688022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.688260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.688498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.688815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.689245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.689643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.690057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.690443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.690842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.692291] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.692690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.719307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.719750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [140.720010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [140.720251] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [140.720485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.720749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.720765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.720988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.721128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.721227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.721471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.721517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.721993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.722382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.722777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.723158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.723541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.724961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.725337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.752672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.753048] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.753164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [140.753418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [140.753404] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.753654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [140.753761] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.753903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.754137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.754372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.754607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.754908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.755312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.755700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.756099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.756474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.756911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.758587] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.759003] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.769869] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.802569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.802961] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.803014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [140.803256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [140.803285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.803475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [140.803589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.803688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.803927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.804144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.804357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.804617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.805091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.805449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.805817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.806167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.806509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.807738] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.808112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.835978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.836348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [140.836578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [140.836830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [140.836842] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.837047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.837167] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.837257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.837472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.837470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.837685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.837951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.838296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.838627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.838971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.839292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.839605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.840869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.841216] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.869259] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.869666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [140.869977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [140.869982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.870234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [140.870336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.870472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.870670] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.870729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [140.870944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [140.871164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [140.871429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.872304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.872671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.873042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.873393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.873765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.875114] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.875486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.902763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.902963] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.903144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.903374] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [140.903476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.903645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [140.903946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [140.904168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.904382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.904592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.904868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.905116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [140.905443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [140.905772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [140.906070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.906354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [140.906654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [140.907680] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.908069] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.935796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.936154] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [140.936416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [140.936653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [140.936943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.936972] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.937151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.937354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [140.937359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.937564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [140.937684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.937818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [140.938130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [140.938433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [140.938741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.939093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [140.939394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [140.940235] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.940540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [140.969729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [140.970071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [140.970250] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458] <7> [140.970355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [140.988014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [140.988328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [140.988530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [140.988926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [140.989133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.989332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.989536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.989813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.990005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.990200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [140.990378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [140.990550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [140.990735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [140.990937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [140.991102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [140.991264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [140.991454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [140.991727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [140.991983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [140.992236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.992541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [140.992861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [140.993877] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [140.994152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.003490] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459] <7> [141.018932] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.052574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.053019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.053010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.053341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.053481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.053606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.053905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.053898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.054140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.054370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.054610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.054906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.055371] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.055640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.056023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.056238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.056449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.056658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.056909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.057136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.057342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.057646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.058012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.058388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.058720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.059024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.059783] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.060068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.085959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.086292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [141.086531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [141.086814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [141.086823] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.087012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.087202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.087189] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.087390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.087493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.087601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.087834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.088209] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.088418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [141.088583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [141.088776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [141.088948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.089117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.089287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.089454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.089627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.089953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.090253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.090544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.090864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.091153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.091905] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.092167] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.119104] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.119478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.119837] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.119862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.120079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.120308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.120307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.120531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.120660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.120842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.121077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.121377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.122008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.122295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.122554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.122819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.123029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.123276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.123485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.123677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.123932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.124232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.124525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.124820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.125145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.125390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.126138] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.126384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.152655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.153083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [141.153160] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.153401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [141.153576] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.153646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [141.153927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.153957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.154189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.154403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.154626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.154917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.155503] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.155802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [141.156051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [141.156252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [141.156439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.156625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.156862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.157046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.157236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.157533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.157851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.158122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.158389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.158659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.159451] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.159730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.185718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.186006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [141.186209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [141.186397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [141.186578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.186853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.187046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.186980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.187232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.187335] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.187437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.187641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.187791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.188055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.188310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.188609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.188894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.189579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.189881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.219018] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.219271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [141.219453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [141.219631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [141.219887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.220106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.220029] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.220291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.220473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.220411] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.220698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.220758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.220975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.221243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.221520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.221793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.222079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.222924] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.223164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.235939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.269003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.269264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.269502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.269741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.269925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.269869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.270122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.270226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.270302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.270475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.270531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.270671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.270990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.271243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.271511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.271795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.272065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.272761] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.273039] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.302361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.302626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [141.302956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [141.302992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.303152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [141.303387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.303373] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.303588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.303728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.303812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.303983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.304178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.304441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.304736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.305027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.305312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.305590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.306507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.306866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.335614] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.335886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [141.336068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [141.336233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [141.336395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.336554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.336821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.337004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.336958] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.337189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.337290] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.337433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.337573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.337684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.337913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.338145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.338372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.339034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.339294] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.369218] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.369499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [141.369781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [141.369978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [141.369936] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.370168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.370355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.370315] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.370542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.370645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.370764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.370986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [141.371294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.371603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.371987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.372323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.372629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.373491] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.373839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.402330] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [141.402661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [141.403026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [141.403129] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.403267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [141.403494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.403538] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.403749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.403970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.403939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.404236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.404507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [141.404878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [141.405207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [141.405586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.405979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [141.406293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [141.407184] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.407513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.435798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026 <7> [141.436070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [141.436302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025 <7> [141.436515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.436782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.436904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.436991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.437236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.437285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.437439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [141.437609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.437689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [141.437897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [141.438087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [141.438270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.438452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.438633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.438862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.439054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.439335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.439609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.439937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.440191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.440439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.441240] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.441526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.442364] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [141.442587] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [141.485582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [141.485880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [141.486090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.486285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.486476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.486743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.486887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.486959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.487197] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.487215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.487464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.487465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.487725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.487994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.488251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.488969] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.489239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.518983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [141.519187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [141.519369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.519545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.519768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.519943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.519898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.520182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.520230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.520512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.520556] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [141.520761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [141.520921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.521074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.521228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.521407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.521592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.521915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.522170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.522424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.522741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.523008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.523731] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.523996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.552344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [141.552597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [141.552874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.553067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.553017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.553253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.553347] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.553457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.553630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.553668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.554022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [141.554187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [141.554344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.554496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.554647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.554866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.555036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.555299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.555553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.555897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.556174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.556434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.557371] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.557692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.585950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [141.586244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [141.586493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.586855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.586894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.587124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.587272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.587338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.587564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.587599] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.588009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [141.588200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [141.588380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.588593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.588867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.589055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.589701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.590092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [141.590266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [141.590435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.590599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.590812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.590966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.591160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.591419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.591693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.591998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.592247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.592491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.593222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.593488] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.618996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [141.619258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [141.619474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.619720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.619847] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.619907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.620126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.620180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.620342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.620465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.620744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [141.620911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [141.621068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.621256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.621420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.621571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.621770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.622125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [141.622287] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [141.622443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.622634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.622862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.623025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.623198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.623472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.623773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.624024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.624273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.624530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.625342] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.625588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.652339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [141.652610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [141.652946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.653085] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.653193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.653425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.653492] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.653738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.653887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.653996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.654311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.654612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.655021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.655312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.655632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.656392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.656686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.702225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [141.702427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [141.702606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.702847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.703023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.702987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.703204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.703320] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.703396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.703604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.703670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.703952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.704230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.704519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.704811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.705499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.705786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.735659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [141.735881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [141.736085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.736279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.736471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.736688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.736826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.736903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.737201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.737209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.737492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.737532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.737866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.738216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.738521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.739321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.739669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.768935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [141.769134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [141.769320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.769550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.769805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.770014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.769936] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.770225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.770317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.770520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.770669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.770830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.771152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.771412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.771746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.772498] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.772781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.802414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [141.802592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [141.802824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.803002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.802960] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.803169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [141.803334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [141.803297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.803516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [141.803580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.803808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [141.804079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [141.804365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.804634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [141.804939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [141.805589] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.805873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.835543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [141.835775] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [141.835946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.836146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [141.836312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [141.836475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [141.836677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.836798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.836936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.837141] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.837193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.837425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.837488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.837749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.837979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.838723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.838980] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.868918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [141.869083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [141.869237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.869387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.869535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.869763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.869941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.869896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.870096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.870251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.870256] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.870400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.870540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.870945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.871187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.919141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [141.919438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [141.919718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.919841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.919918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.920109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.920202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.920335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.920510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.920585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [141.920909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.921169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.921422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.921745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.922032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.922845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.923152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.952778] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460] <7> [141.952802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.953211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.953564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.953686] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [141.953906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [141.954114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.954347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [141.954558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [141.954813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [141.955045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [141.955366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [141.955750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [141.956079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.956358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [141.956649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [141.957433] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.957774] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [141.985575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [141.985853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [141.986043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [141.985985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [141.986262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [141.986340] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [141.986455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [141.986647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [141.986672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [141.986837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [141.987090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [141.987340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [141.987598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.987886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [141.988165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [141.988920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [141.989164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.019071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [142.019257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [142.019428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.019659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.019831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.019784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.019994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.020118] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.020190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.020401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.020489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [142.020764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [142.021042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.021270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.021498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [142.022229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.022487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.052209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [142.052404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [142.052591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.052870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.053046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.052997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.053217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.053352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.053405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.053684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.053795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [142.053962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [142.054126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.054284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.054453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.054662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.054821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.055071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.055316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.055559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.055886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.056144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.056950] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.057204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.085693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [142.085773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.085922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [142.086132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.086206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.086352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.086554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.086561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.086808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.087037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.087454] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [142.087655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [142.087832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.088031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.088202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.088372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.088553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.088863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [142.089169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [142.089437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.089719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.090034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [142.090702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.090975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.118891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [142.119133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [142.119334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.119522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.119778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.119893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.119973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.120233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.120246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.120547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.120648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [142.120840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [142.121023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.121240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.121437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.121658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.121840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.122218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [142.122392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [142.122561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.122815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.122981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.123169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.123353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.123630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.123886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.124140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.124444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.124703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.125349] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.125596] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.152260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [142.152530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [142.152855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.152975] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.153062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.153257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.153330] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.153493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.153661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.153758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.154162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [142.154347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [142.154525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.154733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.154896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.155098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.155267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.155642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [142.155805] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [142.155966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.156127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.156289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.156447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.156627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.156931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [142.157194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [142.157444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.157716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.157968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [142.158756] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.159010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.185591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [142.185926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [142.186008] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.186144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.186355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.186364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.186550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.186701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.186783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.187006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.187312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.187570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.187871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.188153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.188419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.189336] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.189631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.219048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [142.219237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [142.219410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.219587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.219818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.219985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.219941] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.220170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [142.220273] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.220478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [142.220556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.220755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [142.220988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.221218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [142.221478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [142.222159] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.222417] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.252113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [142.252288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [142.252448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.252715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.252884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.252826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.253084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.253165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.253273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [142.253448] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.253528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.253812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.254078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.254336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.254594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.255497] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.255814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.285773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.286126] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.286426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.287247] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461] <7> [142.288325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.288581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [142.288887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [142.289053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [142.289215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.289372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.289529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.289755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.289931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.290090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [142.290250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [142.290405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [142.290557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.290762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.290910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.291057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.291233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.291479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.291754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.292012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.292257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.292502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.293254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.293499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.301849] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [142.321149] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462] <7> [142.323184] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.352296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.352760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.352841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.353087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.353354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.353317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.353632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.353734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.353891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.354202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.354461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.354787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.355153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.355513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.355960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.356309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.356665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.357630] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.357969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.385633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.385765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.385986] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [142.386158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.386290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [142.386511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [142.386482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.386781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.386995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.387203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.387413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.387649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.387959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.388263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.388555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.388935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.389220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.390243] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.390543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.418878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.419169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.419409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.419631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.419754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.419809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.420009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.420067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.420178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.420341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.420334] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.420522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.420817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.421079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.421387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.421699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.421964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.422764] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.423037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.452263] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.452489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [142.452701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [142.452877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [142.452835] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.453082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.453166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.453263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.453427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.453454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.453649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.453874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.454150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.454424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.454708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.454955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.455198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.455915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.456156] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.485426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.485692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [142.485797] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.485885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [142.486053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [142.486129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.486218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.486407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.486413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.486568] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.486773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.486944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.487190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.487430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.487750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.488000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.488297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.489002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.489245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.518801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.519046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [142.519227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [142.519398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [142.519566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.519795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.519955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.519945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.520142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.520258] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.520349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.520523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.520607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.520856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.521139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.521384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.521645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.522304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.522551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.535870] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.568809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.569053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.569246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.569417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.569617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.569747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.569821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.570002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.570079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.570200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.570362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.570385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.570753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.570967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.571137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.571301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.571462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.571648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.571803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.571955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.572110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.572344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.572576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.572923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.573166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.573405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.574035] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.574289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.602168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.602456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [142.602746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [142.602927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [142.602878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.603098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.603189] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.603264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.603434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.603461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.603660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.603883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.604256] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.604463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [142.604659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [142.604814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [142.604964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.605115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.605265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.605414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.605567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.605857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.606114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.606368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.606703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.606948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.607920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.608189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.635556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.635933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.636032] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.636170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.636374] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.636386] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.636567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.636731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.636803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.636980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.637188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.637408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.637803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.638003] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [142.638161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [142.638314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [142.638464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.638637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.638792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.638949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.639112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.639367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.639684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.639928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.640168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.640451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.641276] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.641543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.669148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.669525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [142.669863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [142.670085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [142.670014] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.670297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.670392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.670505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.670753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.670763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.671021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.671281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.671839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.672115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [142.672357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [142.672569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [142.672841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.673043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.673233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.673418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.673633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [142.673946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [142.674219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [142.674489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.674817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [142.675084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [142.675822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.676090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.702102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.702447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [142.702754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [142.702900] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.702996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [142.703225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.703313] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.703448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.703709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.703701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.703999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.704289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.704923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.705218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [142.705488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [142.705763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [142.705972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.706224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.706438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.706693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.706905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [142.707224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [142.707526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [142.707879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.708162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [142.708449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [142.709345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.709611] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.735735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.736267] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.736756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.737846] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463] <7> [142.739986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.740345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [142.740712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [142.740960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [142.741194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.741424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.741692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.741910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.742112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.742311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.742508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.742794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.743005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.743210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.743417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.743652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.743872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [142.744223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.744524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.744868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.745137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.745453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.746267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.746539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.753083] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464] <7> [142.753827] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.785474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.785894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [142.785886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.786162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [142.786237] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.786405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [142.786558] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.786687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.786939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.787194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.787483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.787805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [142.788146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [142.788474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [142.788848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.789239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.789636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [142.790443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.790827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.818809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.819100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [142.819308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [142.819498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [142.819745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.819926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.819871] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.820104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.820201] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.820314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.820486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.820541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [142.820913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.821192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.821480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.821794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.822111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.823194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.823507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.852075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.852402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [142.852717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [142.852840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.852931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [142.853131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.853194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.853368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [142.853507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.853581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [142.853794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [142.854008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [142.854292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [142.854581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [142.854852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.855107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.855390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [142.856124] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.856404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.885682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.885724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.885948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [142.886136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [142.886091] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.886315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [142.886393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.886493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.886764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.886932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [142.887091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [142.887273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [142.887531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.887834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.888103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.888399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.888689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.889419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.889710] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.918714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.918933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [142.919125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [142.919286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [142.919442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.919637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [142.919801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [142.919764] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.919954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [142.920096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.920129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [142.920383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [142.920382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.920645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [142.920903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.921165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [142.921422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [142.922199] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.922470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.952108] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [142.952387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [142.952635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [142.952840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [142.952775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [142.953074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [142.953265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [142.953204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [142.953451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [142.953592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [142.953731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [142.953967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [142.954253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [142.954537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [142.954871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.955176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [142.955454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [142.956291] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [142.956592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [142.969115] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.001979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.002223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [143.002401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [143.002609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [143.002777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.002750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.002966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.003082] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.003140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.003299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.003350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.003470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [143.003753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [143.004007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [143.004257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.004510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.004841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [143.005427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.005712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.035382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.035629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [143.035734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.035824] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [143.035987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [143.036065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.036148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.036306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.036348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.036465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.036654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.036829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [143.037066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.037299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.037594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.037832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.038077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.038981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.039255] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.068696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.068919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [143.069122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [143.069294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [143.069482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.069719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.069915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.069847] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.070090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.070203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.070270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [143.070487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.070652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.070847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [143.070997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [143.071144] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [143.071285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.071425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.071604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.071761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.071906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [143.072154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [143.072448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [143.072724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.072989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.073222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [143.073861] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.074123] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.102333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.102709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [143.102796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.102973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [143.103181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [143.103149] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.103376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.103449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.103653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.103842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.104037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.104231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [143.104628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.104848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [143.105071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [143.105257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [143.105464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.105680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.105866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.106089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.106306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [143.106621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.106917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.107210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.107521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.107851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.108685] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.108988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.135500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.135926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [143.136007] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.136239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [143.136417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.136480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [143.136773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.136814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.137023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.137243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.137455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.137738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [143.138207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.138473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [143.138796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [143.139006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [143.139205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.139405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.139647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.139845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.140048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [143.140366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [143.140743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [143.141081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.141396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [143.141721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [143.142526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.142863] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.168803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [143.169062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [143.169277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [143.169475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.169727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.169905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.169858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.170117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.170209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.170298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [143.170462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.170493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.170665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.170839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.171045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.171214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.171380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.171583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.171810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.172346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026 <7> [143.172532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [143.172788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025 <7> [143.172951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.173147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.173342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.173526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.173755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [143.173918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.174080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.174272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [143.174437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.174621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.174778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.174967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.175133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.175406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.175708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.175957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.176205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.176440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.177183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.177422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.178013] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [143.178193] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [143.201975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [143.202194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [143.202383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.202608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.202785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.202725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.202953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.203039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.203161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.203290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.203409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.203674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.203887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.204098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.204302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.204881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.205094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.235704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.236110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.236523] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465] <7> [143.236436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.238067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [143.238305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [143.238515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.238796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.239002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.239217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.239440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.239778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.240072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.240380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.240698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.240961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.241710] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.241999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.268782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [143.269080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [143.269332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.269625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.269759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.269870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.270147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.270207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.270416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.270630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.270822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.271149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.271465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.271826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.272133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.273031] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.273400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.302353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [143.302708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [143.302840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.302953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.303172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.303221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.303389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.303635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.303590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.303885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.304215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.304567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.304889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.305204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.305567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.306357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.306713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.335333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [143.335567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [143.335768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.335712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.336026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.336123] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.336239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.336458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.336478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.336786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.337124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.337415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.337792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.338067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.338328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.339073] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.339348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.368690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026 <7> [143.368864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025 <7> [143.369025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.369214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.369396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.369603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.369743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.369785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.370036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.370075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.370284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.370356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.370545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.370783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.371037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.371581] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.371817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.401934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [143.402104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [143.402261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.402415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.402620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.402778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.402740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.402956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.403072] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.403209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.403355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.403459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.403740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.404023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.404265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.404874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.405112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.435358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026 <7> [143.435524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025 <7> [143.435758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.435913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.435879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.436105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.436214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.436289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.436468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.436498] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.436747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.436994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.437252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.437511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.437795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.438369] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.438615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.468690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [143.468886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [143.469060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.469231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.469406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.469626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.469759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.469824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.470110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.470137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.470391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.470462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.470714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.470977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.471231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.471963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.472250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.502114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033 <7> [143.502286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018 <7> [143.502446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.502655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.502803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.502796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.502976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.503107] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.503149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [143.503375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.503384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [143.503651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [143.503897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.504172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [143.504410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [143.505073] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.505314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.535279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [143.535453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [143.535673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.535839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.535815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.536003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.536165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.536171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.536344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.536476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.536630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.536878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.537154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.537394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.537673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.538321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.538571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.568666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691 <7> [143.568839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360 <7> [143.568994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.569143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.569319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.569470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.569687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.569837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.569794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.570018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.570165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.570128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.570412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.570793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.571064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.618719] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.618960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.619160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.619346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.619560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.619736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.619697] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.619957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.620012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.620279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.620321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.620483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.620700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.620863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.621056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.621244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.621428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.621720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.621973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.622268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.622528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.622774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.623410] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.623678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.652674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.652853] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466] <7> [143.653052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.653354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.653790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [143.654021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [143.654228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.654419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.654646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.654838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.655062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.655408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [143.655606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [143.655773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.655957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.656126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.656292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.656465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.656758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.657063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.657339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.657614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.657867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.658579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.658850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.685341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.685702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.685725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.685987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.686169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.686264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.686557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.686571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.686841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.687149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.687677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.687929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.688167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.688408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.688689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.688926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.689163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.689657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.689890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.690110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.690328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.690577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.690825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.691067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.691419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.691782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.692119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.692421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.692788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.693617] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.693891] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.718954] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [143.719226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [143.719459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.719753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.719785] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.719955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.720087] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.720156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.720365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.720366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.720803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [143.720993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [143.721175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.721370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.721579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.721757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.721941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.722381] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [143.722605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [143.722788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.722967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.723180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.723353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.723537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.723811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.724073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.724322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.724655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.724887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.725553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.725776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.752040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [143.752388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [143.752769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.752897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.753034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.753289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.753344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.753629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.753781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.753913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.754250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.754589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.754936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.755246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.755580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.756488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.756863] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.785325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691 <7> [143.785572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360 <7> [143.785765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.785690] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.785944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.786036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.786115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.786282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.786319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.786472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.786828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.787102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.787421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.787716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.788050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.788741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.789059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.818585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.818760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.818913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.819085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.819236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.819384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.819648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.819692] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.819896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.820022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.820147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.820305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.820429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.820701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.820930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.821491] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.821775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.851941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691 <7> [143.852124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360 <7> [143.852291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.852459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.852739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.852911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.852870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.853103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.853242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.853372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.853574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.853684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.853989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.854251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.854486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.855208] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.855449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.885259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [143.885474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [143.885741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.885983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [143.885889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.886206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [143.886336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.886421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [143.886691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.886734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.886989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.887342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.887672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.888006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.888294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.889064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.889364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.918758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701 <7> [143.918935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350 <7> [143.919100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.919284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.919443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [143.919641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [143.919768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.919822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [143.920101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.920131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [143.920381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.920378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [143.920713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.920989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [143.921253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [143.921935] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.922220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.951876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [143.952082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [143.952264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.952443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [143.952680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [143.952844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [143.952817] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.953060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [143.953154] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.953315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [143.953436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.953578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [143.953826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.954126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [143.954369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [143.955094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.955336] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [143.985652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [143.986033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [143.986331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [143.987291] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467] <7> [143.988411] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [143.988702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597 <7> [143.988891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162 <7> [143.989061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292 <7> [143.989228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.989391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.989640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.989816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.989984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.990151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [143.990315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [143.990677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [143.990841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [143.990991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [143.991140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [143.991292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [143.991540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [143.991789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [143.992046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [143.992294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [143.992581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [143.992823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [143.993713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [143.993971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.001581] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [144.020609] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468] <7> [144.021887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.051842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.052119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [144.052327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [144.052560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [144.052751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.052710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.052925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.053026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.053095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.053295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.053292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.053515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.053775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.054037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.054298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.054577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.054841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.055614] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.055898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.085211] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.085438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [144.085731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [144.085915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [144.085868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.086099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.086202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.086268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.086435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.086487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.086686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.087191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.087438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [144.087708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [144.087956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.088259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.088522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [144.089307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.089617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.118556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.118794] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [144.118973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [144.119143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [144.119309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.119473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.119706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.119872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.119854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.120056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.120185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.120311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.120471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.120583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.120860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.121111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.121360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.122038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.122286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.152089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.152341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [144.152585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [144.152772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [144.152712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.152939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.153047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.153115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.153275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.153331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.153433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.153653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.154017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.154219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [144.154375] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [144.154561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [144.154734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.154894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.155052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.155207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.155370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.155656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [144.155895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [144.156152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.156380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.156643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [144.157275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.157545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.185364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.185797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [144.185894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.186109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [144.186344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [144.186307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.186618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.186708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.186843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.187063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [144.187325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [144.187646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.188148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.188428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [144.188707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [144.188932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [144.189211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.189437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.189731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [144.189939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [144.190574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.190882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.191178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.191544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.191921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.192214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.193090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.193376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.218701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.219016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [144.219235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [144.219438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [144.219704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.219915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.219854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.220117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.220236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.220357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.220593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.220620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.221057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.221320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597 <7> [144.221549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162 <7> [144.221750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292 <7> [144.221937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.222122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.222308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.222550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.222743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.223064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [144.223386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [144.223790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.224086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.224370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [144.225451] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.225797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.235287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.268548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.268892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [144.269200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [144.269442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [144.269755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.269902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.270045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.270273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.270314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.270577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.270721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.270855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.271399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.271720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [144.271973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [144.272187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [144.272404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.272655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.272880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.273099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.273324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.273683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.273981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.274273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.274620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.274930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.275787] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.276149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.301928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.302283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597 <7> [144.302597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162 <7> [144.302731] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.302831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292 <7> [144.303043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.303110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.303249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.303453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.303437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.303737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.303949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.304234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [144.304529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [144.304807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.305157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.305479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [144.306382] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.306791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.335174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.335440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [144.335772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751 <7> [144.335891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.335971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909 <7> [144.336207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.336304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.336405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.336634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.336669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.336812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.337011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.337285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.337582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.337856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.338165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.338443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.339328] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.339682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.368797] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.369073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599 <7> [144.369274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166 <7> [144.369467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286 <7> [144.369742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.369923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.369879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.370137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.370262] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.370332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.370591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.370596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [144.370872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [144.371180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [144.371432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.371768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [144.372014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [144.372693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.372931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.401801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.402059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [144.402295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753 <7> [144.402488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906 <7> [144.402797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.402977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.402904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.403154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [144.403292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.403366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [144.403591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [144.403626] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.403865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [144.404121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [144.404372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.404645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [144.404947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [144.405673] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.405930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.435660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.436096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.436455] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.437010] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469] <7> [144.439027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.439340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823 <7> [144.439647] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614 <7> [144.439856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614 <7> [144.440055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.440248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.440443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.440758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.440950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.441134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.441308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.441482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.441717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.441876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.442068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.442221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.442400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.442687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.442941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.443189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.443485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.443786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.444667] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.444924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.453089] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470] <7> [144.453978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.485148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.485425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.485698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.485888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.485834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.486068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.486174] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.486242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.486413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.486444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.486663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.486903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.487186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.487450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.487744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.487988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.488233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.488893] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.489165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.518486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.518770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [144.518977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [144.519155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [144.519327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.519569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.519744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.519724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.519913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.520056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.520101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.520339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.520357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.520640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.520907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.521141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.521372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.522116] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.522373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.551759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.552021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.552258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.552452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.552715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.552907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.552845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.553096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.553221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.553282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.553549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.553572] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.553845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.554117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.554434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.554751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.555012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.555716] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.556009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.585281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.585549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [144.585553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.585727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [144.585835] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.585892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [144.586048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.586098] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.586229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.586400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.586587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.586760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.587014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.587266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.587559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.587803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.588048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.588753] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.589016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.618459] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.618829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [144.619062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [144.619238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [144.619412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.619640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.619825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [144.619794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.620014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [144.620177] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.620221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.620527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.620537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.620832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.621100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.621366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.621731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.622459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.622785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.651904] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.652133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [144.652305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [144.652472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [144.652701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.652856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.652833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.653012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.653147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.653195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.653371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.653413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.653739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.653937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823 <7> [144.654097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614 <7> [144.654252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614 <7> [144.654410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.654649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.654822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.654996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.655150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.655386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.655656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.655949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.656196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.656458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.657409] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.657692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.668627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.701812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.702082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.702341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.702587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.702714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.702778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.702958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.703033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.703135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.703326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.703301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.703537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.703899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.704116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.704333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.704540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.704709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.704869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.705027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.705213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.705378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.705657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.705917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.706172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.706418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.706713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.707306] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.707578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.735205] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.735595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [144.735700] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.735860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [144.736128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [144.736150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.736382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.736575] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.736688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.736929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.737195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.737461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.738046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.738314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823 <7> [144.738590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614 <7> [144.738800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614 <7> [144.739011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.739263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.739533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.739754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.739972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.740292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.740638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.741004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.741311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.741639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.742507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.742804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.768521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.768868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.769104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.769321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.769582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.769780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.769720] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.769968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.770093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.770196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.770396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.770416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.770911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.771123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [144.771323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162 <7> [144.771487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292 <7> [144.771702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.771863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.772062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.772244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.772442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.772726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.772995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.773264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.773550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.773809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.774614] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.774876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.802027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.802330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826 <7> [144.802628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620 <7> [144.802729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.802836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605 <7> [144.803032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.803082] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.803266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.803387] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.803469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.803707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.803905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [144.804172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [144.804431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [144.804756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.805008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [144.805260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [144.806037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.806318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.835144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [144.835569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [144.835670] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.835904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165 <7> [144.836148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288 <7> [144.836113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.836379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.836464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.836663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.836887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [144.837135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [144.837379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [144.837766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [144.838119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [144.838436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.838845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [144.839186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [144.840044] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.840347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.868582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018 <7> [144.868818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0 <7> [144.869011] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033 <7> [144.869192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.869366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [144.869578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [144.869759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [144.869718] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.869967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [144.870038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.870159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [144.870329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [144.870322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.870514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [144.870681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.870853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.871028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.871201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.871396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [144.871715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [144.871988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [144.872261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [144.872580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [144.872842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [144.873644] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.873936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.874736] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [144.874987] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A] <7> [144.901859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [144.902168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [144.902401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.902683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.902833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.902889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.903126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.903192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.903345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [144.903523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.903665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [144.903933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [144.904190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [144.904439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [144.904770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [144.905416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.905732] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.935616] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.935803] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471] <7> [144.935965] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.936266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.949925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [144.950176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [144.950387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.950732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [144.950991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [144.951192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [144.951411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [144.951715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [144.951984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [144.952249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [144.952571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [144.952811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [144.953460] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.953735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [144.985067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [144.985261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [144.985433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [144.985778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [144.985714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [144.985964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [144.986069] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [144.986142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [144.986377] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [144.986369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [144.986699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [144.986953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [144.987205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [144.987467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [144.987755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [144.988483] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [144.988820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.018694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [145.018652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.018908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [145.019036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.019104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.019307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.019362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.019655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.019888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.020105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [145.020398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [145.020720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [145.020986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.021298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.021584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [145.022237] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.022507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.051811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [145.052051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [145.052273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.052602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.052733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.052824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.053052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.053166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.053281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.053550] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.053642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.054017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.054345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.054680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.054977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.055826] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.056160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.085156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018 <7> [145.085429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033 <7> [145.085739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.085870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.085965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.086178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.086246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.086432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.086603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.086742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [145.087083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [145.087361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [145.087706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.087981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.088247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [145.088940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.089244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.118403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [145.118661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [145.118847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.118788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.119065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.119147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.119263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.119457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.119459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.119712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.119968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.120220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.120468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.120785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.121046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.121785] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.122044] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.151791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018 <7> [145.151982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033 <7> [145.152155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.152324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.152576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.152657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.152754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.152936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [145.152998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.153190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [145.153282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.153437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [145.153770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.153998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.154259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [145.154881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.155134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.185005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [145.185165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [145.185315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.185465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.185687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.185864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.185833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.186073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.186195] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.186424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [145.186479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.186626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [145.186789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.186975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.187143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.187296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.187459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.187766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.188045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.188323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.188702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.188966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.189732] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.190002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.218635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [145.218652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.218830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [145.219010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.219007] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.219207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.219309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.219379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.219587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.219777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [145.220151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026 <7> [145.220320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025 <7> [145.220484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.220743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.220906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.221063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.221229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2 <7> [145.221508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [145.221778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [145.222058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.222354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [145.222666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [145.223345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.223654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.251695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [145.251925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [145.252129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.252317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.252535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.252559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.252717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.252891] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.252967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.253180] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.253355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [145.253591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [145.253762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.253917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.254070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.254219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.254375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.254736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [145.254895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [145.255050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.255205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.255359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.255526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.255688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.255934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.256172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.256405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.256741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.256984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.257779] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.258030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.285198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [145.285565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [145.285704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.285847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.286134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.286217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.286410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.286750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.286702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.287045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.287308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.287682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.287920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.288332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [145.288593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [145.288813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.289028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.289243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.289459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.289736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.289928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.290118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.290306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.290665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687 <7> [145.290838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364 <7> [145.291015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.291188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.291354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.291547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.291706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.291868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.292072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.292217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.292850] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.293094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.335024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [145.335278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [145.335536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.335744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.335683] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.335931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.336023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.336143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.336304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.336344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.336642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.336941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.337215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.337551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.337840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.338590] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.338893] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.368675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.369016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.369331] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472] <7> [145.369303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.383998] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [145.384265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [145.384523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.384744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.384954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.385202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.385435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.385818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.386158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.386433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.386886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.387139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.387851] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.388110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.418433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [145.418752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [145.418754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.418995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.419262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.419202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.419527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.419609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.419766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.420011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.420337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.420690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.421058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.421362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.421698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.422631] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.422967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.451907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [145.452107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [145.452288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.452480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.452723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.452919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.452858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.453161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.453217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.453456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.453546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.453774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.454020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.454262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.454523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.455199] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.455459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.485040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [145.485317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [145.485655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.485876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.485775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.486095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.486221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.486313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.486590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.486639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.486971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.487281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.487691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.487988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.488260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.489037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.489353] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.518371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687 <7> [145.518590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364 <7> [145.518756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.518715] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.518917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.519080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.519048] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.519240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.519331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.519420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.519694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.519937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.520182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.520421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.520691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.521246] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.521478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.551645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [145.551822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [145.552012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.552176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.552342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.552537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.552679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.552743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.553016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.553022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.553263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.553304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.553519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.553780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.554059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.554641] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.554892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.584963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687 <7> [145.585125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364 <7> [145.585276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.585449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.585680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.585837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.585818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.586025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.586152] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.586278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.586434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.586549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.586789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.587016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.587286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.587938] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.588188] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.618353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [145.618568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [145.618737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.618697] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.618896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.619049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.619039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.619199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.619321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.619371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.619689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.619920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.620145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.620368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.620617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.621363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.621671] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.651903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697 <7> [145.652113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354 <7> [145.652304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.652526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.652715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.652650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.652887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.653012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.653076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2 <7> [145.653314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.653346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [145.653655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [145.653907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.654151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [145.654395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [145.655101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.655348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.684889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [145.685065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [145.685225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.685376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.685573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.685730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.685717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.685950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2 <7> [145.686047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.686216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [145.686329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.686467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [145.686813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.687043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [145.687302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [145.687965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.688219] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.718644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.719014] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.719434] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473] <7> [145.719318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.735780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.736084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583 <7> [145.736337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153 <7> [145.736582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315 <7> [145.736771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.736998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.737190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [145.737396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [145.737663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.737830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.737996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [145.738193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [145.738354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.738521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.738672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.738849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.739052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.739329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [145.739571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [145.739788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.739994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.740187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [145.740936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.741150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.751340] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A] <7> [145.769933] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474] <7> [145.785541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.785894] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.786185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.788537] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.789335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.789768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.818382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.818766] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [145.818738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.819047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [145.819132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.819310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [145.819532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.819597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.819853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.820165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.820426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.820881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [145.821408] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.821736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [145.822026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [145.822301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [145.822557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.822780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.822986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.823217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.823432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [145.823801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [145.824162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [145.824474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.824825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.825168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [145.825971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.826270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.851790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.852099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [145.852320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [145.852609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [145.852607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.852807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.852904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.852996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.853182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.853177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.853402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.853668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.854076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.854309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [145.854508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [145.854687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [145.854862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.855068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.855241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.855412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.855629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.855904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [145.856179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [145.856448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.856754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.857058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [145.857839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.858131] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.884916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.885244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [145.885603] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [145.885740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.885819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [145.886017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.886095] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.886206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.886394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.886397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.886638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.886848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [145.887284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.887508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [145.887676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [145.887845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [145.888014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.888220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [145.888402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [145.888625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [145.888800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [145.889078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [145.889353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [145.889693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.889954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.890244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [145.890962] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.891217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.918539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.918643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.918860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [145.919008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.919090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [145.919291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [145.919312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.919516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.919708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.919883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.920069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.920263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.920721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.920934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [145.921139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [145.921323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [145.921546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.921712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.921861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [145.922005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [145.922158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.922397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [145.922660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [145.922934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.923181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.923423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [145.924176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.924430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.951592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.951874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [145.952110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [145.952304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [145.952473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.952701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [145.952879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [145.952839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.953088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [145.953171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.953282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [145.953453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.953564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [145.953827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [145.954074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.954324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [145.954573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [145.955248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.955527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [145.984889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [145.985119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583 <7> [145.985289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153 <7> [145.985458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315 <7> [145.985693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [145.985864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [145.985828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [145.986068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [145.986160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [145.986248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [145.986445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [145.986444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [145.986741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [145.986992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [145.987237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.987546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [145.987786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [145.988699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [145.988944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.001883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.034833] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.035070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [146.035250] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [146.035422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [146.035652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.035838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.035782] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.036001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.036160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.036115] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.036341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [146.036399] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.036628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [146.036882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [146.037134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.037382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.037686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [146.038322] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.038609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.068216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.068429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583 <7> [146.068696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153 <7> [146.068872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315 <7> [146.068829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.069071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.069187] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.069248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.069418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.069470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.069622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.069807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [146.070043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [146.070278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [146.070557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [146.070787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [146.071015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [146.071733] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.071989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.101599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.101821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [146.101995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738 <7> [146.102158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938 <7> [146.102318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.102478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.102710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.102869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.102856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.103046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [146.103166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.103283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [146.103436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.103531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [146.103765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.104033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.104271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [146.105008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.105265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.135138] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.135399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585 <7> [146.135653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158 <7> [146.135848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308 <7> [146.135784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.136059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.136168] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.136240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.136421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.136540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.136654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.136898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3 <7> [146.137188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [146.137474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [146.137832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [146.138172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [146.138502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [146.139236] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.139520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.168157] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.168361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [146.168561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740 <7> [146.168717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935 <7> [146.168703] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.168877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.169030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.169052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.169197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [146.169364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [146.169335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.169566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3 <7> [146.169813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [146.170062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [146.170302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.170538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [146.170766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [146.171538] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.171791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.202662] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475] <7> [146.202639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.202973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.203272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.224070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.224310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814 <7> [146.224464] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611 <7> [146.224651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626 <7> [146.224788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.224918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.225043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.225178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.225310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.225419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.225560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.225663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.225763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.225861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.225959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.226051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.226162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.226312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.226456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.226619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.226759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.226896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.227456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.227614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.235948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476] <7> [146.250900] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.284905] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.285233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [146.285547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [146.285554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.285761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [146.285924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.285982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.286193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.286265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.286402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.286686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.286945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.287283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.287636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.287985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.288342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.288719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.289660] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.290047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.318381] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.318801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [146.318887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.319053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [146.319273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [146.319272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.319513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.319631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.319721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.319916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.320142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.320362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.320815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.321043] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [146.321271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [146.321449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [146.321672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.321842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.322010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.322177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.322350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.322655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.322916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.323177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.323429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.323744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.324573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.324839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.351632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.351938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [146.352156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [146.352358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [146.352597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.352781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.352723] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.352957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.353056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.353165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.353341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.353384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.353778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.353974] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [146.354130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [146.354291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [146.354438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.354680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.354834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.354988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.355152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.355411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.355698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.355940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.356174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.356449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.357224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.357504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.385096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.385380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [146.385630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [146.385738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.385820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [146.386006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.386092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.386191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.386370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.386378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.386577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.386819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.387173] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.387367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [146.387556] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [146.387735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [146.387897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.388058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.388220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.388382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.388583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.388874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.389110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.389347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.389622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.389877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.390649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.390920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.418230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.418658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [146.418710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.418908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [146.419129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [146.419094] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.419341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.419419] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.419597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.419800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [146.420041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [146.420293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.420829] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.421085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [146.421319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [146.421533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [146.421726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.421971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.422177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [146.422376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [146.422623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.422930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.423221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.423583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.423899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.424183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.425019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.425317] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.451560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.451857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [146.452111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [146.452300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [146.452507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.452687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.452651] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.452864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.452985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.453051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.453242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.453269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.453702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.453918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814 <7> [146.454097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611 <7> [146.454272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626 <7> [146.454448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.454708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.454894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.455087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.455274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.455595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.455928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.456215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.456521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.456805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.457847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.458177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.468345] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.501468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.501798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [146.502044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [146.502239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [146.502427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.502698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.502881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.502822] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.503056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.503155] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.503255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.503436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.503579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.503842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.504106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.504415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.504713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.505309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.505600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.534817] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.535062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814 <7> [146.535276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611 <7> [146.535450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626 <7> [146.535683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.535861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [146.535827] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.536067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [146.536169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.536240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [146.536427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.536450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.536718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.536959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.537243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.537511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.537745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.538558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.538826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.568122] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.568362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [146.568584] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156 <7> [146.568754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309 <7> [146.568701] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.568916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.569082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [146.569028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.569245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [146.569313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.569442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [146.569704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.569970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.570217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.570527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.570814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.571066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.571784] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.572056] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.601664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.601911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817 <7> [146.602087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617 <7> [146.602255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617 <7> [146.602454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.602705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.602821] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.602885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [146.603087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [146.603157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.603273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3 <7> [146.603442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.603539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [146.603792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [146.604046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.604309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [146.604606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [146.605307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.605563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.634792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.635037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [146.635206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158 <7> [146.635368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305 <7> [146.635619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.635787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [146.635755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.635952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [146.636116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [146.636108] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.636301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3 <7> [146.636393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.636568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [146.636826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [146.637062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.637325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [146.637568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [146.638224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.638506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.668082] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [146.668371] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [146.668654] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [146.668794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.668909] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [146.669112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.669147] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A] <7> [146.669378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [146.669413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A] <7> [146.669699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset] <7> [146.669936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [146.670161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [146.670385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [146.670639] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [146.670882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [146.671101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [146.671319] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [146.671550] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [146.671766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [146.671981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [146.672195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7> [146.672423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [146.672684] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [146.672898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7> [146.673108] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [146.673318] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [146.673547] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [146.673759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [146.673973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [146.674184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [146.674396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [146.674645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [146.674871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [146.675124] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [146.675385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [146.675630] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [146.675845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [146.676053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [146.676304] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [146.676548] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [146.676780] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [146.676982] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [146.677184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [146.677388] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [146.677658] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no, <7> [146.677871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [146.678074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [146.678276] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [146.678491] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [146.678693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [146.678892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [146.679089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [146.679283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [146.679467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [146.679695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [146.679882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [146.680062] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.680238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.680403] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.680592] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [146.680777] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [146.680940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.681095] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.681244] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [146.681395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [146.681574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [146.681731] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes <7> [146.681884] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [146.682048] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0 <7> [146.682198] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no <7> [146.682334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [146.682467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes <7> [146.682628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0 <7> [146.682760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0 <7> [146.682922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [146.683068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [146.683265] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1 <7> [146.683400] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on <7> [146.683578] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [146.684501] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [146.685712] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1] <7> [146.685829] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A] <7> [146.688107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0 <7> [146.688186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0 <7> [146.688248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0 <7> [146.688305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [146.688356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [146.688642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [146.688885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.688988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [146.689047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0 <7> [146.689131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [146.689211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [146.689289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [146.689366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [146.689446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [146.689718] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <6> [146.704516] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS <7> [146.705051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7> [146.705133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [146.705200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [146.705264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7> [146.705327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <7> [146.705399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1 <7> [146.705512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [146.705622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [146.705748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [146.705848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [146.705939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [146.717849] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [146.719404] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [146.720026] [IGT] kms_rotation_crc: exiting, ret=0 <6> [146.735235] Console: switching to colour frame buffer device 180x56 <7> [146.785639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [146.786005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [146.786288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<6> [136.050528] Console: switching to colour dummy device 80x25

<6> [136.050715] [IGT] kms_rotation_crc: executing

<7> [136.055626] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [136.055635] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [136.055783] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [136.055995] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [136.055997] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [136.056138] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [136.056398] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [136.056401] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [136.056520] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<7> [136.056770] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]

<7> [136.056773] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]

<7> [136.057212] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00

<7> [136.057527] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000

<7> [136.057634] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [136.057738] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [136.057856] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz

<5> [136.057860] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [136.057862] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [136.057863] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00

<7> [136.057865] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<5> [136.057866] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [136.057868] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor

<5> [136.057870] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [136.057871] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0

<5> [136.057872] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [136.057884] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes

<7> [136.057969] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [136.058109] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<5> [136.058763] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [136.058765] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [136.058766] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [136.058818] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:

<7> [136.058822] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [136.058825] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [136.058841] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]

<7> [136.058844] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]

<7> [136.058983] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected

<7> [136.058993] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]

<7> [136.058995] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]

<7> [136.059130] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected

<7> [136.059137] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]

<7> [136.059139] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]

<7> [136.059242] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected

<6> [136.059435] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top

<7> [136.060735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0

<7> [136.060810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [136.060875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [136.060939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [136.061001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [136.061111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [136.061237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [136.061359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [136.061454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [136.061543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [136.061631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [136.061917] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.062026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.062179] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<7> [136.069966] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [136.070213] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [136.070404] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [136.070504] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [136.070587] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [136.070670] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation

<7> [136.070745] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [136.070829] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [136.070935] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [136.071019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [136.071137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [136.071243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [136.071345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [136.071432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [136.071516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [136.071600] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [136.071684] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [136.071766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [136.071847] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [136.071921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [136.071996] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [136.072085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [136.072187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8

<7> [136.072287] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [136.072382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [136.072463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [136.072546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [136.072641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [136.072736] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [136.072829] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [136.072911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [136.072988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [136.073072] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [136.073173] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [136.073278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [136.073377] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [136.073454] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [136.073529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [136.073604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [136.073679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [136.073753] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [136.073828] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [136.073898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [136.073969] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [136.074043] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [136.074164] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [136.074253] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [136.074341] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [136.074429] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [136.074517] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [136.074605] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [136.074693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [136.074778] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [136.074852] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [136.074939] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [136.075026] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075306] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [136.075383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [136.075450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075519] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075589] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [136.075659] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [136.075728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [136.086372] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [136.086504] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [136.106122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.106423] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.106645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.137494] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]

<7> [136.138882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [136.139296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [136.139603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.139880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.140203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.140467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.140752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.141059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.141313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.141584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.141899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.142332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.142770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.143215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.143555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.143892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.144947] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.145341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.146331] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [136.146598] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [136.152896] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1

<7> [136.155662] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]

<7> [136.187212] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.187759] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.188260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.188948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]

<7> [136.189849] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.190292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.190598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.190948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.191311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.191597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.191926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.192535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.192812] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.193076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.193374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.193620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.193862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.194532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.194982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.195390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.195799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.196127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.196470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.196820] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz

<7> [136.197502] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.197790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.220082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.220462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.220771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.220974] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]

<7> [136.221777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [136.222022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [136.222344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.222554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.222759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.222997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.223298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.223730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [136.223937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [136.224175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.224411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.224604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.224792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.224986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.225323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.225650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.225927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.226229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.226550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.227378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.227688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.254143] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]

<7> [136.254093] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.254509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.254860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.254927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.255244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.255481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.255704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.255932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.256268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.256564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.257054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.257281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.257478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.257672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.257863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.258158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.258399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.258905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.259208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.259395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.259620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.259821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.260006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.260266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.260570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.260871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.261240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.261609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.261905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.262858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.263177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.287159] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.287411] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]

<7> [136.287546] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.287832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.301927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [136.302217] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [136.302429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.302618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.302799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.302984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.303220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.303554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [136.303706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [136.303852] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.303988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.304157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.304288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.304419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.304693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [136.304840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [136.304977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.305321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.305431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.305536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.305641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.305806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.305967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.306169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.306325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.306474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.306942] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.307151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.336875] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]

<7> [136.337081] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.337556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.337981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.353160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [136.353422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [136.353643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.353846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.354063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [136.354250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [136.354498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.354776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.355048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.355302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.355556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.355814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.356756] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.357021] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.386805] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]

<7> [136.387542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [136.387811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [136.388118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.388104] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.388362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.388471] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.388596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.388794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.388877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.389205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.389573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.389941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.390438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.390819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.391190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.392126] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.392487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.404188] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437]

<7> [136.437139] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]

<7> [136.437139] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.437562] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.437918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.438102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.438365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.438603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.438831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.439095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.439319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.439624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.439978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.440380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.440700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.441015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.441436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.442219] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.442536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.470122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.470534] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.470707] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]

<7> [136.470853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.471471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [136.471675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [136.471855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.472049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.472224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.472424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.472616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.472870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.473169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.473436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.473712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.473999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.474811] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.475145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.503833] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]

<7> [136.504128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.504511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.504586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [136.504793] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [136.504829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.504984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.505281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.505469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.505691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.505933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.506268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.506562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.506849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.507168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.507429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.508320] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.508584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.537068] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.537446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.537600] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441]

<7> [136.537752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.550329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [136.550572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [136.550784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.551000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.551396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.551669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.551905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [136.552272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [136.552542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [136.552790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.553040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [136.553315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [136.553973] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.554394] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.587163] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442]

<7> [136.587113] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.587479] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.587836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.604308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [136.604577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [136.604805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.605056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.605264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [136.605514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [136.605759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.606199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.606436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.606659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.606873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.607150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.607921] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.608142] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.636657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [136.637049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [136.637392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.637722] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.637968] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.638143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.638442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.638466] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.638719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.638875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.638993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.639351] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.639635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.640556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.640957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.686512] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.686817] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.687182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.687204] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.687424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.687650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.687619] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.687907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.687971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.688197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.688535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [136.688861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [136.689214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.689577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.689931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [136.690822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.691146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.719957] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443]

<7> [136.720867] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [136.721130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [136.721162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.721336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.721574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.721549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.721787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.721892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.722068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.722319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.722639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.722942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.723395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.723680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.723986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.725031] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.725356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.753126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.753326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.753511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.753696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.753887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.754181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.754147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.754452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.754499] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.754784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [136.754821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.755111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [136.755458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.755759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.756108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [136.757169] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.757522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.786652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [136.786865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [136.787109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.787117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.787306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.787432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.787503] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.787679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.787712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.787888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.788369] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [136.788564] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [136.788751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.788937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.789173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.789397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.789589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.789898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.790252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.790623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.790977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.791390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.792268] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.792610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.819786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [136.820040] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.820058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [136.820250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.820285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.820432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.820504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.820608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [136.820797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [136.821016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.821390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [136.821569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [136.821740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.821913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.822133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [136.822308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [136.822492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.822768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [136.823081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [136.823420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.823710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.824018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [136.825125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.825461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.853168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [136.853443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [136.853675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.853891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.854179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.854199] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.854401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.854511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.854700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.854800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.855184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [136.855406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [136.855627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.855883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.856135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.856339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.856602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.857090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [136.857315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [136.857511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.857703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.857897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.858143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.858376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.858714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.859096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.859430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.859766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.860102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.860941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.861255] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.886455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.886725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.886963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.887279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.887296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.887507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.887624] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.887765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.887934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.888023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.888513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.888750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.888959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.889223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.889430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.889677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.889914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.890455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.890679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.890893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.891222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.891417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.891629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.891847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.892202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [136.892494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [136.892783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.893063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.893346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [136.894082] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.894341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.919801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [136.920119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.920189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [136.920427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.920427] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.920649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [136.920712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.920865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [136.921192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [136.921446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.921794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.922150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.922473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.922845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.923258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.924207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.924514] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.953093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [136.953297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [136.953489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.953677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [136.953869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [136.954130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [136.954141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.954369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [136.954467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.954690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [136.954760] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.955075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [136.955422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.955758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [136.956164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [136.957185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.957537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [136.986519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [136.986697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [136.986858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [136.987119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [136.987092] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [136.987278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [136.987333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [136.987432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [136.987552] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [136.987604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [136.987841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [136.988120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [136.988417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.988660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [136.988964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [136.989744] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [136.990060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.019720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [137.019940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [137.020202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.020207] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.020395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.020498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.020581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.020763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.020763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.020995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [137.021362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.021732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.022049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.022411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.022766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.023846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.024256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.054050] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444]

<7> [137.055023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.055341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.055452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.055633] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.055762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [137.056111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [137.056355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [137.056591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.056821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.057120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.057349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.057573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.057841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [137.058111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [137.058348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [137.058558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.058762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.058969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.059250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.059495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.059849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.060228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.060611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.060988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.061374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.062523] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.062917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.069390] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [137.088269] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445]

<7> [137.089739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.118030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.118399] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.119647] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.119759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.120054] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [137.120044] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [137.120045] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [137.120189] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.120528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.120792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.121089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.121392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.121641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.121880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.122177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.122513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.122840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.123196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.123521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.123846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.124708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.125251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.153116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.153473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [137.153731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [137.154001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [137.154036] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.154227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.154497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.154445] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.154717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.154802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.154933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.155246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.155637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.155948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.156349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.156690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.157000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.158163] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.158464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.186360] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.186712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.187013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.187117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.187233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.187441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.187498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.187643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.187848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.187825] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.188166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.188419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.188743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.189052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.189403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.189689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.189997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.190877] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.191230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.219872] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.220175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [137.220228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.220429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [137.220624] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [137.220606] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.220812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.220935] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.221025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.221203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [137.221377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [137.222069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.222333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.222586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.222838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.223165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.223420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.224102] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.224360] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.253076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.253418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [137.253726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [137.254016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [137.254108] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.254243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.254511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.254553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.254738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.254934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.255015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.255243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.255562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.255864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.256181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.256465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.256743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.257578] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.257865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.286335] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.286620] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [137.286834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [137.287071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [137.287170] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.287247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.287415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.287484] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.287581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.287771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.287747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.288006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.288406] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.288616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [137.288787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [137.288941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [137.289140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.289294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.289446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.289595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.289752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.290009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.290311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.290562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.290851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.291127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.291771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.292036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.303084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.336337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.336643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.336910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.337248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.337377] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.337486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.337716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.337787] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.337947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.338198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.338299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.338565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.339027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.339271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.339467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.339659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.339850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.340145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.340358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.340617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.340867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.341258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.341580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.341879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.342252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.342587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.343285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.343564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.369662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.370009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [137.370122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.370253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [137.370460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [137.370475] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.370655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.370779] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.370883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.371106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.371278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.371512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.371986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.372183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [137.372339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [137.372491] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [137.372640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.372786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.372941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.373162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.373344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.373638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.373907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.374173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.374404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.374650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.375584] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.375852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.403012] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.403336] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.403571] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.403786] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.404058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.404083] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.404282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.404436] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.404504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.404772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.404752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.405035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.405539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.405776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [137.405978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [137.406158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [137.406334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.406542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.406732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.406926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.407156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.407414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.407671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.407928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.408221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.408522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.409248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.409515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.436484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.436798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [137.437093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [137.437208] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.437291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [137.437480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.437539] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.437661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.437838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [137.437823] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.438085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [137.438290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [137.438538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [137.438787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [137.439088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.439345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [137.439648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [137.440377] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.440629] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.469670] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.470009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [137.470098] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.470270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [137.470488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [137.470509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.470699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.470861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.470994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.471208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.471463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.471699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [137.472043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [137.472394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [137.472764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.473107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [137.473422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [137.474386] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.474712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.503996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.504412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.504671] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446]

<7> [137.504765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.506812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.507182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [137.507428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [137.507657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [137.507880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.508136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.508340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.508578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.508768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.508959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.509138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.509312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.509484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.509652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.509821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.510052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.510251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.510515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.510772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.511063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.511314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.511557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.512363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.512631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.520914] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447]

<7> [137.521838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.552906] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.553234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.553480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.553687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.553886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.554141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.554252] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.554328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.554525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.554585] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.554730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.554871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.555035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.555305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.555566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.555822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.556128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.556765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.557062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.586307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.586609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [137.586879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [137.587177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [137.587284] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.587399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.587663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.587692] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.587886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.588075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.588157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.588376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.588669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.588957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.589236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.589502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.589801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.590898] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.591232] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.619583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.619851] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.620138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.620324] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.620264] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.620505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.620620] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.620720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.620908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.620924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.621161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.621344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.621599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.621848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.622125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.622358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.622588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.623275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.623532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.653060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.653284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [137.653450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [137.653610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [137.653795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.653998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.654023] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.654164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [137.654327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [137.654356] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.654511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.654639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.654768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.655016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.655296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.655535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.655764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.656499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.656765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.686217] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.686486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [137.686689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [137.686880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [137.687158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.687335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.687280] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.687510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.687637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.687717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.687970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.687976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.688233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.688485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.688737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.689002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.689284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.689920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.690228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.719612] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.719896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [137.720193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [137.720404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [137.720336] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.720610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.720807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.720745] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.721032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.721110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.721234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.721473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.721768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.722120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.722484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.722844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.723211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.724055] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.724354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.736635] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.769524] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.769750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.769921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.770200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.770288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.770369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.770542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.770621] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.770708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.770870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.770911] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.771090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.771498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.771689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.771839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.772028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.772184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.772370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.772523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.772674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.772830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.773100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.773332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.773564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.773838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.774130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.774771] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.775036] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.803002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.803306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [137.803559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [137.803765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [137.803994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.804174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.804122] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.804353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.804454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.804561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.804739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.804754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.805222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.805431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [137.805597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [137.805759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [137.805917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.806129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.806324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.806508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.806670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.806940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.807198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.807450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.807695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.807971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.808941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.809207] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.836327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.836655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.836887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.837161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.837304] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.837358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.837594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.837661] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.837800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.838074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.838037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.838299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.838717] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.838981] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [137.839176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [137.839372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [137.839558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.839771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.839973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.840141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.840314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.840590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.840873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.841212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.841556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.841838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.842669] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.842956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.869902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.870353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [137.870440] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.870694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [137.870886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.870991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [137.871245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.871345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.871492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.871738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [137.872037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [137.872284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.872849] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.873194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [137.873496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [137.873734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [137.874022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.874254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.874482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [137.874710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [137.874947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [137.875268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [137.875587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [137.875982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.876290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [137.876569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [137.877359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.877642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.902999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.903422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [137.903768] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [137.904127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [137.904266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.904406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.904730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.904748] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.905079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.905211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.905330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.905595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.906200] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [137.906499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [137.906763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [137.907029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [137.907262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.907494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [137.907717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [137.907955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [137.908192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [137.908536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [137.908877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [137.909252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.909622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [137.909954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [137.910870] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.911197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.936377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [137.936698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [137.937036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [137.937180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.937298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.937553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.937632] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.937841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.938038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.938117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.938358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [137.938603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [137.938842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [137.939100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [137.939311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.939514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [137.939714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [137.939935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [137.940168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [137.940498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [137.940815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [137.941222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [137.941561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [137.941877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [137.942759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.943072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [137.943739] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [137.943975] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [137.969521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [137.969735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [137.969948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [137.970067] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [137.970130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [137.970292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [137.970371] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [137.970479] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [137.970626] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [137.970675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [137.970933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [137.971156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [137.971371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [137.971605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [137.971808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [137.972364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [137.972557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.004015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448]

<7> [138.004004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.004457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.004838] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.005044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [138.005315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [138.005565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.005808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.006077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.006306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.006545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [138.006868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [138.007245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [138.007558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.007904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.008275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [138.009123] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.009452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.036267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [138.036543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [138.036774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.037080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.037174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.037311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.037590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.037586] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.037839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.037965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.038178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.038479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.038811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.039135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.039472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.040468] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.040773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.069789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [138.070125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [138.070267] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.070362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.070587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.070648] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.070803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.071047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.071139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.071394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [138.071733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [138.072097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [138.072420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.072792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.073153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [138.073996] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.074305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.102872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [138.103161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [138.103375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.103636] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.103851] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.104158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.104290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.104395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.104701] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.104717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.105099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.105073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.105446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.105752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.106148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.106981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.107279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.136245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [138.136482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [138.136672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.136859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.137120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.137313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.137259] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.137568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [138.137638] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.137865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [138.137993] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.138186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [138.138503] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.138783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.139061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [138.139661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.139925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.169523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [138.169726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [138.169956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.170165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.170100] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.170365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.170511] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.170606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.170870] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.170871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.171269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.171579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.172190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.172496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.172792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.173782] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.174138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.202942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [138.203051] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.203150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [138.203338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.203431] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.203520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.203698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.203757] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.203953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.204175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [138.204492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [138.204800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [138.205123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.205459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.205733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [138.206450] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.206723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.236188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [138.236394] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [138.236602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.236834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.237086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.237265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.237226] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.237469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.237611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.237757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.237971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.238120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.238403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.238660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.238911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.239605] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.239856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.269734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [138.269999] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [138.270210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.270143] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.270457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.270550] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.270663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.270868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.270956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.271186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [138.271599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [138.271960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [138.272295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.272628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [138.273173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [138.274061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.274373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.302845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [138.303099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [138.303185] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.303279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.303498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.303566] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.303682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.303859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.303939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.304146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.304587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [138.304778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [138.305048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.305230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.305411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.305614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.305831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.306163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.306450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.306739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.307132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.307446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.308263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.308560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.336264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [138.336516] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [138.336732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.336973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.337003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.337161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.337336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.337379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.337566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.337621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.337736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.337932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.338090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.338371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [138.338522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [138.338671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.338822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.339024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.339181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.339336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.339491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.339642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.339795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.340556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.340836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.386186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.386465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.386699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.386967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.387110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.387201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.387439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.387523] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.387693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.387875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.388207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.388426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.388637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.388841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.389117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.389340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.389585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.390054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.390257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.390453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.390647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.390843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.391100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.391346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.391670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.391991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.392279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.392568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.392869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.393687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.394016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.419937] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.420395] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.420748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.421531] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449]

<7> [138.422340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [138.422628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [138.422907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.423149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.423410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.423676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.424038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.424535] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [138.424758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [138.425013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.425261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.425476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.425682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.425910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.426340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [138.426567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [138.426751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.427025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.427198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.427372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.427551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.427810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.428098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.428367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.428602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.428831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.429553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.429775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.452847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.453307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.453393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.453564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.453799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.453801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.454084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.454214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.454331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.454610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.455024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.455353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.455675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.456057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.456372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.457270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.457605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.486404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [138.486675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [138.486969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.487116] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.487213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.487451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.487534] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.487716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.487931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.488016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.488387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.488747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.489211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.489560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.489917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.490847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.491272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.519416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [138.519654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [138.519857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.520138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.520235] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.520315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.520493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.520549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.520682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.520821] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.520952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.521216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.521471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.521771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.522061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.522721] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.523003] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.552807] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [138.553069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [138.553163] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.553261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.553488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.553551] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.553685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.553906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.553910] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.554105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.554379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.554648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.554939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.555234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.555495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.556158] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.556434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.586139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.586396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.586591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.586819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.587097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.587305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.587234] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.587589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.587644] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.587916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.588008] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.588206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.588498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.588798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.589118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.589847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.590151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.619439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [138.619626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [138.619798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.620040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.620119] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.620213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.620410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.620472] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.620603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.620776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.620892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.621148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.621396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.621691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.621936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.622556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.622797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.652795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [138.653063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [138.653148] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.653253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.653433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.653528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.653616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.653830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.653853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.654162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.654438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.654701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.655048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.655318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.655572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.656304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.656576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.686309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [138.686504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [138.686683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.687061] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.687181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.687375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.687446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.687574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.687772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.687875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [138.688150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [138.688418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [138.688706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.689025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [138.689335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [138.690106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.690385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.716924] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD off

<7> [138.717153] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [138.719348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [138.719533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [138.719699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.719927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.720018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.720099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.720253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.720329] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.720420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [138.720594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.720659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [138.720918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [138.721167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.721409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [138.721651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [138.722390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.722669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.753145] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.753481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.753762] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.753969] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450]

<7> [138.755502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.755747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [138.755989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [138.756160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [138.756326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.756487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.756680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.756863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.757023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.757177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [138.757369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [138.757549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [138.757717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.757892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.758049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.758202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.758381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.758637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [138.758901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [138.759205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.759451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.759748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [138.760794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.761086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.769076] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [138.787711] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451]

<7> [138.789684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.819370] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.819678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [138.820010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [138.820137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.820258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [138.820496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.820552] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.820730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.820953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.821016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.821325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.821636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [138.822073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [138.822439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [138.822793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.823205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.823546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [138.824479] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.824889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.852812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.853196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [138.853241] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.853438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [138.853660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [138.853620] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.853963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.853969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.854176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.854383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.854632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.854892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.855325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.855567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [138.855802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [138.856053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [138.856281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.856482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.856662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.856906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.857129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.857425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [138.857719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [138.858034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.858307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.858572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [138.859419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.859704] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.886175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.886531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [138.886820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [138.887151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [138.887267] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.887394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.887620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.887675] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.887862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.888100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.888081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.888347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [138.888815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.889131] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [138.889350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [138.889561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [138.889817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.890086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [138.890342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [138.890567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [138.890780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [138.891137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [138.891454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [138.891767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.892096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.892379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [138.893244] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.893518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.919960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.920010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.920348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [138.920460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.920685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [138.920894] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.921026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [138.921290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.921539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.921777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.922077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.922318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.922774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.923073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [138.923283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [138.923486] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [138.923685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.923909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.924108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [138.924303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [138.924527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.924871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [138.925231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [138.925549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.925880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.926185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [138.927065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.927375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.952769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.953184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [138.953285] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.953471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [138.953715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [138.953694] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.954001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.954094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.954231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.954456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.954730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.955042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [138.955592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.955863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [138.956115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [138.956323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [138.956512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.956717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [138.956947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [138.957148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [138.957377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [138.957710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [138.958048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [138.958338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.958624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [138.958912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [138.959730] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.960039] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [138.986105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.986412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [138.986689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [138.986955] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [138.987084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [138.987169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.987420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.987462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [138.987632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.987790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [138.987875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.988101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.988643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [138.989341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [138.989538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [138.989725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [138.989961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [138.990144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [138.990326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [138.990504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [138.990691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [138.991028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [138.991326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [138.991652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.991961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [138.992295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [138.993324] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [138.993612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.002812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.036980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.037152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.037242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.037353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [139.037425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.037497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [139.037610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [139.037719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.037823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.037977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.038078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.038207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [139.038350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [139.038487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [139.038617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.038743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.038885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [139.039341] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.039478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.069197] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.069325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [139.069399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [139.069460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [139.069520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.069578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.069635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.069691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.069756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [139.069867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [139.069881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.069987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [139.070040] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.070096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [139.070167] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.070202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [139.070306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [139.070648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.070748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.102762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.103142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [139.103228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.103405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [139.103611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [139.103622] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.103813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.104002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.104077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.104261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.104438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.104647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [139.104988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [139.105247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [139.105501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.105797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.106088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [139.106804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.107241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.136288] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.136563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [139.136771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [139.137045] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [139.137142] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.137230] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.137449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.137498] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.137653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.137805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.137893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.138098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [139.138389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [139.138642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [139.138910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [139.139217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [139.139469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [139.140272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.140531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.169351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.169680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [139.170001] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [139.170091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.170209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [139.170403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.170446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.170592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.170746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.170780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [139.171053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [139.171257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [139.171519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [139.171778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [139.172061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.172362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [139.172615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [139.173353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.173612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.202965] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.203303] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.203590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.204127] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452]

<7> [139.205866] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.206135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [139.206326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [139.206501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [139.206668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.206859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.207035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.207214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.207381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.207544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.207706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.207892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.208041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.208185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.208330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.208473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.208644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.208903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.209164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.209420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.209669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.209945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.210800] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.211104] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.220301] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453]

<7> [139.221244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.252716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.253122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [139.253206] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.253437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [139.253619] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.253685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [139.253971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.254005] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.254238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.254453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.254686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.254968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.255303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.255635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.256059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.256365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.256668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.257439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.257734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.286065] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.286372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [139.286594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [139.286795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [139.287115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.287225] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.287325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.287527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.287604] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.287734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.287974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.288002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.288309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.288611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.288930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.289274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.289562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.290439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.290749] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.319325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.319659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [139.319973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [139.320028] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.320216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [139.320448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.320443] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.320666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.320796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.320919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.321138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.321381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.321686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.322000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.322270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.322535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.322884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.323750] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.324068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.352873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.352957] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.353103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [139.353271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [139.353289] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.353436] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [139.353599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.353569] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.353794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.354018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.354180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.354356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.354689] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.354911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [139.355068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [139.355219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [139.355369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.355516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.355663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.355805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.356017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.356253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.356488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.356728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.357000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.357278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.357961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.358206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.386112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.386442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [139.386680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [139.386969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [139.387003] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.387203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.387429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.387411] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.387650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [139.387765] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.387954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [139.388197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.388681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.388988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [139.389196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [139.389397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [139.389628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.389853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.390049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [139.390242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [139.390443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.390763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.391136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.391502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.391841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.392125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.392889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.393191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.419553] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.420030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [139.420103] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.420357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [139.420646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [139.420590] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.420978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.421066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.421250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.421517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.421857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.422121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.422643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.422963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [139.423193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [139.423416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [139.423644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.423912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.424177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.424393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.424614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.425000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.425407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.425739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.426093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.426401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.427405] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.427689] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.436074] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.469285] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.469575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [139.469792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [139.470093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [139.470228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.470312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.470523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.470609] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.470734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.470976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.471045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.471257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.471725] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.471968] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [139.472142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [139.472311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [139.472514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.472695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.472903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.473122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.473328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.473607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.473911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.474231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.474521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.474827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.475555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.475839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.502666] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.502991] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [139.503081] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.503216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [139.503409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [139.503415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.503594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.503700] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.503773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.504023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.504196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.504380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.504628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.504888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.505150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.505414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.505661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.506392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.506644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.535918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.536139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [139.536317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [139.536474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [139.536627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.536778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.537004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.537038] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.537167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.537345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.537372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.537601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.537656] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.537864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.538144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.538381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.538607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.539355] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.539612] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.569513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.569842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [139.569975] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.570123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [139.570344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [139.570421] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.570593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.570825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.570842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.571041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.571272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.571557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [139.572012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [139.572407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [139.572817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.573178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [139.573509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [139.574427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.574768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.602622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [139.602967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [139.602995] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.603269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [139.603372] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.603489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [139.603700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.603697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.603965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.604155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [139.604340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [139.604544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [139.604894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [139.605153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [139.605407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.605674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [139.605946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [139.606666] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.606949] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.636187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [139.636449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [139.636689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [139.637032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.637164] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.637268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.637517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.637611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.637771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.638063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [139.638065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.638282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [139.638496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [139.638704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [139.638958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.639145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.639338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.639544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.639780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.640163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.640504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.640837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.641142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.641476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.642470] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.642815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.643715] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [139.644011] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [139.669305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.669582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.669864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.669986] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.670103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.670334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.670397] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.670607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.670750] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.670889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.671255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [139.671613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [139.671984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.672371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.672726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [139.673612] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.673995] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.703766] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454]

<7> [139.703830] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.704333] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.704721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.720622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [139.720965] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [139.721211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.721445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.721671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.721972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.722219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.722531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.722990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.723257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.723510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.723760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.724681] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.724945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.752667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.752984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.752941] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.753190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.753380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.753326] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.753581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.753658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.753838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.754076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.754400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [139.754717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [139.755150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.755515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.755872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [139.756926] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.757315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.786267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [139.786542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [139.786776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.787050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.787168] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.787253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.787486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.787521] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.787735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.787854] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.788057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.788337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.788609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.788955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.789229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.789952] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.790236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.819223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [139.819433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [139.819623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.819858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.819982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.820073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [139.820267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [139.820364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.820485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.820690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.821220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [139.821520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [139.821822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.822136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.822440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [139.823320] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.823623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.852680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [139.852984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [139.853096] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.853205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.853458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.853509] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.853678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.853947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.853902] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.854176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.854497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.854821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.855200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.855504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.855823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.856562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.856918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.885929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.886128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.886312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.886496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.886724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.886985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.887110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.887217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.887490] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.887657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.887877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.887844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.888042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.888205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.888365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.888523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.888686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.888993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [139.889258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [139.889545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.889823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.890082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [139.890754] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.891068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.919293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [139.919531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [139.919731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.919976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.920097] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.920154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.920358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.920415] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.920570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.920682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.920964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [139.921142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [139.921308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.921508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [139.921690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [139.921908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [139.922067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.922309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.922549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.922801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.923112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.923363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.924051] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.924300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.952578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.952871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.952991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.953105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.953378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.953400] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.953595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.953751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.953877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.954134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.954653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.954923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.955148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.955387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.955629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.955932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.956175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.956681] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [139.957008] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [139.957227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.957481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [139.957694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [139.957962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [139.958183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [139.958526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [139.958875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [139.959241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.959601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [139.959949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [139.960844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.961135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [139.986226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [139.986522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [139.986813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.986932] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [139.987034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.987245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.987311] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [139.987468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.987636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [139.987702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.988221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [139.988441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [139.988649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.988892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.989104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.989343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.989558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.990012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [139.990202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [139.990382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [139.990559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [139.990738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [139.990967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [139.991140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [139.991408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [139.991678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [139.991972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.992222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [139.992466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [139.993185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [139.993420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.019240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [140.019539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [140.019839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.019948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.020084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.020315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.020359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.020594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.020718] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.020904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.021297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.021629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.021985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.022279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.022570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.023427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.023731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.052612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [140.052893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [140.053104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.053035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.053360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.053446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.053574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.053823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.053843] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.054047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.054266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.054482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.054695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.055599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.056037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.102679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [140.103040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [140.103271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.103487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.103694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.104006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.104115] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.104262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.104556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.104597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.104970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.104976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.105300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.105615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.106111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.107007] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.107346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.137090] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455]

<7> [140.136955] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.137376] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.137751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.154012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [140.154298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [140.154522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.154732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.155011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.155200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.155453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.155721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.156036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.156265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.156487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.156723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.157343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.157552] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.185905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [140.186133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [140.186328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.186563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.186809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.186824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.187032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.187211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.187286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.187535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.187613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.187983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.188381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.188722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.189275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.190330] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.190693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.219484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [140.219896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [140.219947] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.220214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.220395] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.220472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.220726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.220816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.221083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.221341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.221733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.222114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.222436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.222772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.223111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.223977] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.224310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.252520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [140.252778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [140.252896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.252986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.253225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.253277] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.253447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.253640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.253602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.253888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.254166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.254440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.254707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.255044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.255288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.256020] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.256281] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.285884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [140.286091] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [140.286315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.286510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.286695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.286939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.287052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.287141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.287417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.287408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.287689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.287711] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.288021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.288264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.288506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.289165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.289423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.319112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [140.319303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [140.319508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.319678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.319911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.320034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.320105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.320334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.320390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.320615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.320693] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.320910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.321153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.321393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.321684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.322289] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.322543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.352546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [140.352782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [140.352892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.352979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.353208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.353273] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.353405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.353587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.353599] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.353817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.354108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.354459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.354787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.355071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.355345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.356141] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.356415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.385871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [140.386075] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [140.386251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.386431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.386647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.386895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.386920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.387117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.387331] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.387433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.387683] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.387770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.388058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.388339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.388612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.389472] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.389778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.419353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [140.419555] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [140.419777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.419973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.419890] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.420144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.420307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.420251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.420493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [140.420555] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.420780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [140.421087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [140.421357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.421597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [140.421871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [140.422542] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.422832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.452479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [140.452669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [140.452916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.452964] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.453105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.453286] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.453344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.453472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.453672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.453667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.454095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [140.454259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [140.454417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.454570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.454725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.454933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.455089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [140.455336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.455582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.455993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.456227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.456492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.457369] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.457690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.486908] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456]

<7> [140.486883] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.487299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.487645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.509513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.510261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [140.510478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [140.510660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [140.510866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.511042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.511212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [140.511391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [140.511566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.511752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.511920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [140.512062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [140.512205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.512339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.512470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.512596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.512790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.513274] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.513490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [140.513633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [140.513781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [140.513915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.514041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.514165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [140.514283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [140.514389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.514490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.514588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [140.514686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [140.514822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.514942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.515047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.515152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.515280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.515465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.515636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.515806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.515953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.516101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.517018] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.517209] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.518775] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [140.537452] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457]

<7> [140.553764] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.554061] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.554243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.558781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.559638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.559804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.586011] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.586418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [140.586670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [140.586936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [140.586953] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.587157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.587297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.587357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.587561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.587614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.587790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.588053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.588801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.589063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [140.589242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [140.589407] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [140.589571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.589742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.589908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.590069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.590243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.590500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.590772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.591028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.591264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.591490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.592364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.592614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.619373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.619785] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [140.620024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [140.620245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [140.620461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.620675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.620934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.620943] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.621164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.621297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.621437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.621620] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.622199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.622489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [140.622706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [140.623050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [140.623268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.623480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.623695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.623926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.624160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.624522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.624892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.625230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.625552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.625891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.627137] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.627439] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.652647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.652959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.653027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [140.653194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [140.653257] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.653350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [140.653510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.653521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.653675] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.653853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.654022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.654236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.654532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.654826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.655082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.655332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.655569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.656606] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.656887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.686432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.686754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.686960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [140.687133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.687254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [140.687505] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [140.687483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.687780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.688022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.688260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.688498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.688815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.689245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.689643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.690057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.690443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.690842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.692291] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.692690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.719307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.719750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [140.720010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [140.720251] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [140.720485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.720749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.720765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.720988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.721128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.721227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.721471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.721517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.721993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.722382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.722777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.723158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.723541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.724961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.725337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.752672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.753048] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.753164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [140.753418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [140.753404] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.753654] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [140.753761] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.753903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.754137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.754372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.754607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.754908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.755312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.755700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.756099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.756474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.756911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.758587] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.759003] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.769869] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.802569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.802961] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.803014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [140.803256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [140.803285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.803475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [140.803589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.803688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.803927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.804144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.804357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.804617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.805091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.805449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.805817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.806167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.806509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.807738] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.808112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.835978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.836348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [140.836578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [140.836830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [140.836842] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.837047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.837167] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.837257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.837472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.837470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.837685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.837951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.838296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.838627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.838971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.839292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.839605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.840869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.841216] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.869259] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.869666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [140.869977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [140.869982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.870234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [140.870336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.870472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.870670] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.870729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [140.870944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [140.871164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [140.871429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.872304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.872671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.873042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.873393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.873765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.875114] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.875486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.902763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.902963] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.903144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.903374] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [140.903476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.903645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [140.903946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [140.904168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.904382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.904592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.904868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.905116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [140.905443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [140.905772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [140.906070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.906354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [140.906654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [140.907680] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.908069] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.935796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.936154] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [140.936416] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [140.936653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [140.936943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.936972] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.937151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.937354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [140.937359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.937564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [140.937684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.937818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [140.938130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [140.938433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [140.938741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.939093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [140.939394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [140.940235] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.940540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [140.969729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [140.970071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [140.970250] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458]

<7> [140.970355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [140.988014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [140.988328] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [140.988530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [140.988926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [140.989133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.989332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.989536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.989813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.990005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.990200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [140.990378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [140.990550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [140.990735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [140.990937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [140.991102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [140.991264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [140.991454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [140.991727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [140.991983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [140.992236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.992541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [140.992861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [140.993877] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [140.994152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.003490] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459]

<7> [141.018932] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.052574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.053019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.053010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.053341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.053481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.053606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.053905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.053898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.054140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.054370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.054610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.054906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.055371] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.055640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.056023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.056238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.056449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.056658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.056909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.057136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.057342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.057646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.058012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.058388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.058720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.059024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.059783] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.060068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.085959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.086292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [141.086531] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [141.086814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [141.086823] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.087012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.087202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.087189] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.087390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.087493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.087601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.087834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.088209] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.088418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [141.088583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [141.088776] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [141.088948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.089117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.089287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.089454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.089627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.089953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.090253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.090544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.090864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.091153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.091905] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.092167] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.119104] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.119478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.119837] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.119862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.120079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.120308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.120307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.120531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.120660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.120842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.121077] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.121377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.122008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.122295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.122554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.122819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.123029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.123276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.123485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.123677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.123932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.124232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.124525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.124820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.125145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.125390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.126138] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.126384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.152655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.153083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [141.153160] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.153401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [141.153576] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.153646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [141.153927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.153957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.154189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.154403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.154626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.154917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.155503] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.155802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [141.156051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [141.156252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [141.156439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.156625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.156862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.157046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.157236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.157533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.157851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.158122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.158389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.158659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.159451] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.159730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.185718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.186006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [141.186209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [141.186397] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [141.186578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.186853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.187046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.186980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.187232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.187335] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.187437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.187641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.187791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.188055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.188310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.188609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.188894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.189579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.189881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.219018] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.219271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [141.219453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [141.219631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [141.219887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.220106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.220029] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.220291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.220473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.220411] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.220698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.220758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.220975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.221243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.221520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.221793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.222079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.222924] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.223164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.235939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.269003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.269264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.269502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.269741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.269925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.269869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.270122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.270226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.270302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.270475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.270531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.270671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.270990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.271243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.271511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.271795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.272065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.272761] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.273039] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.302361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.302626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [141.302956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [141.302992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.303152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [141.303387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.303373] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.303588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.303728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.303812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.303983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.304178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.304441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.304736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.305027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.305312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.305590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.306507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.306866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.335614] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.335886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [141.336068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [141.336233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [141.336395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.336554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.336821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.337004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.336958] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.337189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.337290] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.337433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.337573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.337684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.337913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.338145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.338372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.339034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.339294] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.369218] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.369499] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [141.369781] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [141.369978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [141.369936] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.370168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.370355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.370315] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.370542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.370645] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.370764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.370986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [141.371294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.371603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.371987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.372323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.372629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.373491] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.373839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.402330] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [141.402661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [141.403026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [141.403129] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.403267] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [141.403494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.403538] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.403749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.403970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.403939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.404236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.404507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [141.404878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [141.405207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [141.405586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.405979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [141.406293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [141.407184] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.407513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.435798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 2026), size 588 -> 2026

<7> [141.436070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [141.436302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2026 - 4051), size 2305 -> 2025

<7> [141.436515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.436782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.436904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.436991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.437236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.437285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.437439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [141.437609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.437689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [141.437897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [141.438087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [141.438270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.438452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.438633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.438862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.439054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.439335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.439609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.439937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.440191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.440439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.441240] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.441526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.442364] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [141.442587] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [141.485582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [141.485880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [141.486090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.486285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.486476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.486743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.486887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.486959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.487197] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.487215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.487464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.487465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.487725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.487994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.488251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.488969] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.489239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.518983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [141.519187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [141.519369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.519545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.519768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.519943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.519898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.520182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.520230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.520512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.520556] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [141.520761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [141.520921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.521074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.521228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.521407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.521592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.521915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.522170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.522424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.522741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.523008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.523731] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.523996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.552344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [141.552597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [141.552874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.553067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.553017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.553253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.553347] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.553457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.553630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.553668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.554022] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [141.554187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [141.554344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.554496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.554647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.554866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.555036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.555299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.555553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.555897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.556174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.556434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.557371] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.557692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.585950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [141.586244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [141.586493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.586855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.586894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.587124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.587272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.587338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.587564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.587599] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.588009] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [141.588200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [141.588380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.588593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.588867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.589055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.589701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.590092] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [141.590266] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [141.590435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.590599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.590812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.590966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.591160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.591419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.591693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.591998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.592247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.592491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.593222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.593488] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.618996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [141.619258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [141.619474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.619720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.619847] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.619907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.620126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.620180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.620342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.620465] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.620744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [141.620911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [141.621068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.621256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.621420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.621571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.621770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.622125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [141.622287] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [141.622443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.622634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.622862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.623025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.623198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.623472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.623773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.624024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.624273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.624530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.625342] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.625588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.652339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [141.652610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [141.652946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.653085] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.653193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.653425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.653492] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.653738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.653887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.653996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.654311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.654612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.655021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.655312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.655632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.656392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.656686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.702225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [141.702427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [141.702606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.702847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.703023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.702987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.703204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.703320] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.703396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.703604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.703670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.703952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.704230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.704519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.704811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.705499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.705786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.735659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [141.735881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [141.736085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.736279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.736471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.736688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.736826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.736903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.737201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.737209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.737492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.737532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.737866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.738216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.738521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.739321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.739669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.768935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [141.769134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [141.769320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.769550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.769805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.770014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.769936] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.770225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.770317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.770520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.770669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.770830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.771152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.771412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.771746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.772498] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.772781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.802414] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [141.802592] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [141.802824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.803002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.802960] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.803169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [141.803334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [141.803297] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.803516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [141.803580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.803808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [141.804079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [141.804365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.804634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [141.804939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [141.805589] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.805873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.835543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [141.835775] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [141.835946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.836146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [141.836312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [141.836475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [141.836677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.836798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.836936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.837141] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.837193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.837425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.837488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.837749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.837979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.838723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.838980] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.868918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [141.869083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [141.869237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.869387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.869535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.869763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.869941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.869896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.870096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.870251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.870256] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.870400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.870540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.870945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.871187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.919141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [141.919438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [141.919718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.919841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.919918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.920109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.920202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.920335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.920510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.920585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [141.920909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.921169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.921422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.921745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.922032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.922845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.923152] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.952778] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460]

<7> [141.952802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.953211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.953564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.953686] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [141.953906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [141.954114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.954347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [141.954558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [141.954813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [141.955045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [141.955366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [141.955750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [141.956079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.956358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [141.956649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [141.957433] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.957774] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [141.985575] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [141.985853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [141.986043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [141.985985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [141.986262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [141.986340] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [141.986455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [141.986647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [141.986672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [141.986837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [141.987090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [141.987340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [141.987598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.987886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [141.988165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [141.988920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [141.989164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.019071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [142.019257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [142.019428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.019659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.019831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.019784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.019994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.020118] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.020190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.020401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.020489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [142.020764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [142.021042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.021270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.021498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [142.022229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.022487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.052209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [142.052404] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [142.052591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.052870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.053046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.052997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.053217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.053352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.053405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.053684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.053795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [142.053962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [142.054126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.054284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.054453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.054662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.054821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.055071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.055316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.055559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.055886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.056144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.056950] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.057204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.085693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [142.085773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.085922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [142.086132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.086206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.086352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.086554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.086561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.086808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.087037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.087454] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [142.087655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [142.087832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.088031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.088202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.088372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.088553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.088863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [142.089169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [142.089437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.089719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.090034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [142.090702] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.090975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.118891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [142.119133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [142.119334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.119522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.119778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.119893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.119973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.120233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.120246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.120547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.120648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [142.120840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [142.121023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.121240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.121437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.121658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.121840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.122218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [142.122392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [142.122561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.122815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.122981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.123169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.123353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.123630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.123886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.124140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.124444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.124703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.125349] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.125596] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.152260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [142.152530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [142.152855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.152975] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.153062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.153257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.153330] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.153493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.153661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.153758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.154162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [142.154347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [142.154525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.154733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.154896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.155098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.155267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.155642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [142.155805] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [142.155966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.156127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.156289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.156447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.156627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.156931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [142.157194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [142.157444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.157716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.157968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [142.158756] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.159010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.185591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [142.185926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [142.186008] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.186144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.186355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.186364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.186550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.186701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.186783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.187006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.187312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.187570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.187871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.188153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.188419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.189336] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.189631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.219048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [142.219237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [142.219410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.219587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.219818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.219985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.219941] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.220170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [142.220273] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.220478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [142.220556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.220755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [142.220988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.221218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [142.221478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [142.222159] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.222417] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.252113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [142.252288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [142.252448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.252715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.252884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.252826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.253084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.253165] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.253273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [142.253448] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.253528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.253812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.254078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.254336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.254594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.255497] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.255814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.285773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.286126] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.286426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.287247] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461]

<7> [142.288325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.288581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [142.288887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [142.289053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [142.289215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.289372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.289529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.289755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.289931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.290090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [142.290250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [142.290405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [142.290557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.290762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.290910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.291057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.291233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.291479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.291754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.292012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.292257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.292502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.293254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.293499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.301849] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [142.321149] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462]

<7> [142.323184] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.352296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.352760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.352841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.353087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.353354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.353317] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.353632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.353734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.353891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.354202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.354461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.354787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.355153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.355513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.355960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.356309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.356665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.357630] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.357969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.385633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.385765] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.385986] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [142.386158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.386290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [142.386511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [142.386482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.386781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.386995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.387203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.387413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.387649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.387959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.388263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.388555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.388935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.389220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.390243] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.390543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.418878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.419169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.419409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.419631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.419754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.419809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.420009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.420067] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.420178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.420341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.420334] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.420522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.420817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.421079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.421387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.421699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.421964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.422764] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.423037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.452263] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.452489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [142.452701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [142.452877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [142.452835] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.453082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.453166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.453263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.453427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.453454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.453649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.453874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.454150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.454424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.454708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.454955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.455198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.455915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.456156] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.485426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.485692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [142.485797] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.485885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [142.486053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [142.486129] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.486218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.486407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.486413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.486568] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.486773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.486944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.487190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.487430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.487750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.488000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.488297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.489002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.489245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.518801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.519046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [142.519227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [142.519398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [142.519566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.519795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.519955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.519945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.520142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.520258] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.520349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.520523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.520607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.520856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.521139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.521384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.521645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.522304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.522551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.535870] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.568809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.569053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.569246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.569417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.569617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.569747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.569821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.570002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.570079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.570200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.570362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.570385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.570753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.570967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.571137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.571301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.571462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.571648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.571803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.571955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.572110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.572344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.572576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.572923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.573166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.573405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.574035] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.574289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.602168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.602456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [142.602746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [142.602927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [142.602878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.603098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.603189] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.603264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.603434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.603461] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.603660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.603883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.604256] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.604463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [142.604659] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [142.604814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [142.604964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.605115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.605265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.605414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.605567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.605857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.606114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.606368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.606703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.606948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.607920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.608189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.635556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.635933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.636032] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.636170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.636374] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.636386] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.636567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.636731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.636803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.636980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.637188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.637408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.637803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.638003] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [142.638161] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [142.638314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [142.638464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.638637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.638792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.638949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.639112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.639367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.639684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.639928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.640168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.640451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.641276] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.641543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.669148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.669525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [142.669863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [142.670085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [142.670014] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.670297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.670392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.670505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.670753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.670763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.671021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.671281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.671839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.672115] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [142.672357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [142.672569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [142.672841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.673043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.673233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.673418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.673633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [142.673946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [142.674219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [142.674489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.674817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [142.675084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [142.675822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.676090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.702102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.702447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [142.702754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [142.702900] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.702996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [142.703225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.703313] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.703448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.703709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.703701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.703999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.704289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.704923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.705218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [142.705488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [142.705763] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [142.705972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.706224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.706438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.706693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.706905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [142.707224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [142.707526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [142.707879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.708162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [142.708449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [142.709345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.709611] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.735735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.736267] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.736756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.737846] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463]

<7> [142.739986] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.740345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [142.740712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [142.740960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [142.741194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.741424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.741692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.741910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.742112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.742311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.742508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.742794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.743005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.743210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.743417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.743652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.743872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [142.744223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.744524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.744868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.745137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.745453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.746267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.746539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.753083] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464]

<7> [142.753827] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.785474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.785894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [142.785886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.786162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [142.786237] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.786405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [142.786558] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.786687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.786939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.787194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.787483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.787805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [142.788146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [142.788474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [142.788848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.789239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.789636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [142.790443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.790827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.818809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.819100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [142.819308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [142.819498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [142.819745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.819926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.819871] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.820104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.820201] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.820314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.820486] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.820541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [142.820913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.821192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.821480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.821794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.822111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.823194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.823507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.852075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.852402] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [142.852717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [142.852840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.852931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [142.853131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.853194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.853368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [142.853507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.853581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [142.853794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [142.854008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [142.854292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [142.854581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [142.854852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.855107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.855390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [142.856124] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.856404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.885682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.885724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.885948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [142.886136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [142.886091] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.886315] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [142.886393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.886493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.886764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.886932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [142.887091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [142.887273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [142.887531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.887834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.888103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.888399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.888689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.889419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.889710] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.918714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.918933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [142.919125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [142.919286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [142.919442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.919637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [142.919801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [142.919764] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.919954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [142.920096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.920129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [142.920383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [142.920382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.920645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [142.920903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.921165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [142.921422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [142.922199] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.922470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.952108] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [142.952387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [142.952635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [142.952840] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [142.952775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [142.953074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [142.953265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [142.953204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [142.953451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [142.953592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [142.953731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [142.953967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [142.954253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [142.954537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [142.954871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.955176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [142.955454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [142.956291] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [142.956592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [142.969115] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.001979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.002223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [143.002401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [143.002609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [143.002777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.002750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.002966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.003082] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.003140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.003299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.003350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.003470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [143.003753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [143.004007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [143.004257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.004510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.004841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [143.005427] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.005712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.035382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.035629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [143.035734] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.035824] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [143.035987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [143.036065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.036148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.036306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.036348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.036465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.036654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.036829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [143.037066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.037299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.037594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.037832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.038077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.038981] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.039255] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.068696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.068919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [143.069122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [143.069294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [143.069482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.069719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.069915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.069847] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.070090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.070203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.070270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [143.070487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.070652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.070847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [143.070997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [143.071144] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [143.071285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.071425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.071604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.071761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.071906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [143.072154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [143.072448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [143.072724] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.072989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.073222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [143.073861] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.074123] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.102333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.102709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [143.102796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.102973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [143.103181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [143.103149] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.103376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.103449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.103653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.103842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.104037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.104231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [143.104628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.104848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [143.105071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [143.105257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [143.105464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.105680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.105866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.106089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.106306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [143.106621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.106917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.107210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.107521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.107851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.108685] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.108988] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.135500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.135926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [143.136007] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.136239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [143.136417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.136480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [143.136773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.136814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.137023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.137243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.137455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.137738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [143.138207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.138473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [143.138796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [143.139006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [143.139205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.139405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.139647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.139845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.140048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [143.140366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [143.140743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [143.141081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.141396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [143.141721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [143.142526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.142863] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.168803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [143.169062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [143.169277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [143.169475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.169727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.169905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.169858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.170117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.170209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.170298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [143.170462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.170493] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.170665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.170839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.171045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.171214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.171380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.171583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.171810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.172346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2026), size 598 -> 2026

<7> [143.172532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [143.172788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2026 - 4051), size 2288 -> 2025

<7> [143.172951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.173147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.173342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.173526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.173755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [143.173918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.174080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.174272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [143.174437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.174621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.174778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.174967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.175133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.175406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.175708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.175957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.176205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.176440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.177183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.177422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.178013] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [143.178193] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [143.201975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [143.202194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [143.202383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.202608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.202785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.202725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.202953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.203039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.203161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.203290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.203409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.203674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.203887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.204098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.204302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.204881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.205094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.235704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.236110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.236523] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465]

<7> [143.236436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.238067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [143.238305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [143.238515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.238796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.239002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.239217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.239440] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.239778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.240072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.240380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.240698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.240961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.241710] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.241999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.268782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [143.269080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [143.269332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.269625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.269759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.269870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.270147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.270207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.270416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.270630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.270822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.271149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.271465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.271826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.272133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.273031] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.273400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.302353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [143.302708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [143.302840] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.302953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.303172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.303221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.303389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.303635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.303590] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.303885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.304215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.304567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.304889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.305204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.305567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.306357] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.306713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.335333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [143.335567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [143.335768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.335712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.336026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.336123] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.336239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.336458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.336478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.336786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.337124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.337415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.337792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.338067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.338328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.339073] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.339348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.368690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2026), size 1364 -> 2026

<7> [143.368864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2026 - 4051), size 2687 -> 2025

<7> [143.369025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.369214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.369396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.369603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.369743] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.369785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.370036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.370075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.370284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.370356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.370545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.370783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.371037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.371581] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.371817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.401934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [143.402104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [143.402261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.402415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.402620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.402778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.402740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.402956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.403072] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.403209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.403355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.403459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.403740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.404023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.404265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.404874] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.405112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.435358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2026), size 1361 -> 2026

<7> [143.435524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2026 - 4051), size 2690 -> 2025

<7> [143.435758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.435913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.435879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.436105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.436214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.436289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.436468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.436498] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.436747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.436994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.437252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.437511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.437795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.438369] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.438615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.468690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [143.468886] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [143.469060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.469231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.469406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.469626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.469759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.469824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.470110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.470137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.470391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.470462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.470714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.470977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.471231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.471963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.472250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.502114] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2033), size 1361 -> 2033

<7> [143.502286] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1361 - 4051) -> (2033 - 4051), size 2690 -> 2018

<7> [143.502446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.502655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.502803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.502796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.502976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.503107] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.503149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [143.503375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.503384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [143.503651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [143.503897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.504172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [143.504410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [143.505073] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.505314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.535279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [143.535453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [143.535673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.535839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.535815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.536003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.536165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.536171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.536344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.536476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.536630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.536878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.537154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.537394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.537673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.538321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.538571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.568666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2691), size 1364 -> 2691

<7> [143.568839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1364 - 4051) -> (2691 - 4051), size 2687 -> 1360

<7> [143.568994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.569143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.569319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.569470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.569687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.569837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.569794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.570018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.570165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.570128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.570412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.570793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.571064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.618719] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.618960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.619160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.619346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.619560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.619736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.619697] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.619957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.620012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.620279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.620321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.620483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.620700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.620863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.621056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.621244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.621428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.621720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.621973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.622268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.622528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.622774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.623410] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.623678] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.652674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.652853] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466]

<7> [143.653052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.653354] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.653790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [143.654021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [143.654228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.654419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.654646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.654838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.655062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.655408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [143.655606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [143.655773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.655957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.656126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.656292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.656465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.656758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.657063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.657339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.657614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.657867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.658579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.658850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.685341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.685702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.685725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.685987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.686169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.686264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.686557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.686571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.686841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.687149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.687677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.687929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.688167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.688408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.688689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.688926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.689163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.689657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.689890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.690110] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.690328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.690577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.690825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.691067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.691419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.691782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.692119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.692421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.692788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.693617] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.693891] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.718954] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [143.719226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [143.719459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.719753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.719785] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.719955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.720087] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.720156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.720365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.720366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.720803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [143.720993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [143.721175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.721370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.721579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.721757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.721941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.722381] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [143.722605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [143.722788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.722967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.723180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.723353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.723537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.723811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.724073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.724322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.724655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.724887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.725553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.725776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.752040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [143.752388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [143.752769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.752897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.753034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.753289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.753344] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.753629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.753781] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.753913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.754250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.754589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.754936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.755246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.755580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.756488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.756863] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.785325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2691), size 2031 -> 2691

<7> [143.785572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (2691 - 4051), size 2020 -> 1360

<7> [143.785765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.785690] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.785944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.786036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.786115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.786282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.786319] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.786472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.786828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.787102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.787421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.787716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.788050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.788741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.789059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.818585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.818760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.818913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.819085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.819236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.819384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.819648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.819692] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.819896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.820022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.820147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.820305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.820429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.820701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.820930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.821491] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.821775] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.851941] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2691), size 2026 -> 2691

<7> [143.852124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2691 - 4051), size 2025 -> 1360

<7> [143.852291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.852459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.852739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.852911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.852870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.853103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.853242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.853372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.853574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.853684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.853989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.854251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.854486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.855208] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.855449] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.885259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [143.885474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [143.885741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.885983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [143.885889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.886206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [143.886336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.886421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [143.886691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.886734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.886989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.887342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.887672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.888006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.888294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.889064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.889364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.918758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2701), size 2026 -> 2701

<7> [143.918935] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2701 - 4051), size 2025 -> 1350

<7> [143.919100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.919284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.919443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [143.919641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [143.919768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.919822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [143.920101] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.920131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [143.920381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.920378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [143.920713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.920989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [143.921253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [143.921935] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.922220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.951876] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [143.952082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [143.952264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.952443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [143.952680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [143.952844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [143.952817] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.953060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [143.953154] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.953315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [143.953436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.953578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [143.953826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.954126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [143.954369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [143.955094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.955336] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [143.985652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [143.986033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [143.986331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [143.987291] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467]

<7> [143.988411] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [143.988702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2031) -> ( 0 - 597), size 2031 -> 597

<7> [143.988891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 597 - 1759), size 0 -> 1162

<7> [143.989061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2031 - 4051) -> (1759 - 4051), size 2020 -> 2292

<7> [143.989228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.989391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.989640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.989816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.989984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.990151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [143.990315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [143.990677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [143.990841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [143.990991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [143.991140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [143.991292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [143.991540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [143.991789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [143.992046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [143.992294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [143.992581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [143.992823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [143.993713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [143.993971] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.001581] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [144.020609] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468]

<7> [144.021887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.051842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.052119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [144.052327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [144.052560] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [144.052751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.052710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.052925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.053026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.053095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.053295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.053292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.053515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.053775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.054037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.054298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.054577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.054841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.055614] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.055898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.085211] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.085438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [144.085731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [144.085915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [144.085868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.086099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.086202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.086268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.086435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.086487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.086686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.087191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.087438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [144.087708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [144.087956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.088259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.088522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [144.089307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.089617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.118556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.118794] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [144.118973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [144.119143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [144.119309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.119473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.119706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.119872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.119854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.120056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.120185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.120311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.120471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.120583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.120860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.121111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.121360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.122038] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.122286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.152089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.152341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [144.152585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [144.152772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [144.152712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.152939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.153047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.153115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.153275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.153331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.153433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.153653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.154017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.154219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [144.154375] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [144.154561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [144.154734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.154894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.155052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.155207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.155370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.155656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [144.155895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [144.156152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.156380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.156643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [144.157275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.157545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.185364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.185797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [144.185894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.186109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [144.186344] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [144.186307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.186618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.186708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.186843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.187063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [144.187325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [144.187646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.188148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.188428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [144.188707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [144.188932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [144.189211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.189437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.189731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [144.189939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [144.190574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.190882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.191178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.191544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.191921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.192214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.193090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.193376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.218701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.219016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [144.219235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [144.219438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [144.219704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.219915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.219854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.220117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.220236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.220357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.220593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.220620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.221057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.221320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 597), size 392 -> 597

<7> [144.221549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 597 - 1759), size 753 -> 1162

<7> [144.221750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (1759 - 4051), size 2906 -> 2292

<7> [144.221937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.222122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.222308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.222550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.222743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.223064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [144.223386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [144.223790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.224086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.224370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [144.225451] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.225797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.235287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.268548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.268892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [144.269200] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [144.269442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [144.269755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.269902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.270045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.270273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.270314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.270577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.270721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.270855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.271399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.271720] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [144.271973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [144.272187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [144.272404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.272655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.272880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.273099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.273324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.273683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.273981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.274273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.274620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.274930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.275787] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.276149] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.301928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.302283] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 597), size 391 -> 597

<7> [144.302597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 597 - 1759), size 751 -> 1162

<7> [144.302731] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.302831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1759 - 4051), size 2909 -> 2292

<7> [144.303043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.303110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.303249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.303453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.303437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.303737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.303949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.304234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [144.304529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [144.304807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.305157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.305479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [144.306382] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.306791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.335174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.335440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [144.335772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 391 - 1142), size 1162 -> 751

<7> [144.335891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.335971] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (1142 - 4051), size 2292 -> 2909

<7> [144.336207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.336304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.336405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.336634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.336669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.336812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.337011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.337285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.337582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.337856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.338165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.338443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.339328] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.339682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.368797] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.369073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 391) -> ( 0 - 599), size 391 -> 599

<7> [144.369274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 391 - 1142) -> ( 599 - 1765), size 751 -> 1166

<7> [144.369467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1142 - 4051) -> (1765 - 4051), size 2909 -> 2286

<7> [144.369742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.369923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.369879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.370137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.370262] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.370332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.370591] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.370596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [144.370872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [144.371180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [144.371432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.371768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [144.372014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [144.372693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.372931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.401801] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.402059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [144.402295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 599 - 1765) -> ( 392 - 1145), size 1166 -> 753

<7> [144.402488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1765 - 4051) -> (1145 - 4051), size 2286 -> 2906

<7> [144.402797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.402977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.402904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.403154] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [144.403292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.403366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [144.403591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [144.403626] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.403865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [144.404121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [144.404372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.404645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [144.404947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [144.405673] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.405930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.435660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.436096] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.436455] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.437010] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469]

<7> [144.439027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.439340] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 392) -> ( 0 - 823), size 392 -> 823

<7> [144.439647] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 392 - 1145) -> ( 823 - 2437), size 753 -> 1614

<7> [144.439856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1145 - 4051) -> (2437 - 4051), size 2906 -> 1614

<7> [144.440055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.440248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.440443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.440758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.440950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.441134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.441308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.441482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.441717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.441876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.442068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.442221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.442400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.442687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.442941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.443189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.443485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.443786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.444667] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.444924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.453089] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470]

<7> [144.453978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.485148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.485425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.485698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.485888] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.485834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.486068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.486174] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.486242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.486413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.486444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.486663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.486903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.487186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.487450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.487744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.487988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.488233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.488893] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.489165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.518486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.518770] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [144.518977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [144.519155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [144.519327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.519569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.519744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.519724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.519913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.520056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.520101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.520339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.520357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.520640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.520907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.521141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.521372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.522116] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.522373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.551759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.552021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.552258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.552452] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.552715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.552907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.552845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.553096] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.553221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.553282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.553549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.553572] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.553845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.554117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.554434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.554751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.555012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.555716] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.556009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.585281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.585549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [144.585553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.585727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [144.585835] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.585892] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [144.586048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.586098] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.586229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.586400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.586587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.586760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.587014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.587266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.587559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.587803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.588048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.588753] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.589016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.618459] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.618829] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [144.619062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [144.619238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [144.619412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.619640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.619825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [144.619794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.620014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [144.620177] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.620221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.620527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.620537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.620832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.621100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.621366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.621731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.622459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.622785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.651904] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.652133] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [144.652305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [144.652472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [144.652701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.652856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.652833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.653012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.653147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.653195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.653371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.653413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.653739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.653937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 823), size 598 -> 823

<7> [144.654097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 823 - 2437), size 1165 -> 1614

<7> [144.654252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2437 - 4051), size 2288 -> 1614

<7> [144.654410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.654649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.654822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.654996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.655150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.655386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.655656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.655949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.656196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.656458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.657409] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.657692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.668627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.701812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.702082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.702341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.702587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.702714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.702778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.702958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.703033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.703135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.703326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.703301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.703537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.703899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.704116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.704333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.704540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.704709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.704869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.705027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.705213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.705378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.705657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.705917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.706172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.706418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.706713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.707306] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.707578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.735205] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.735595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [144.735700] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.735860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [144.736128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [144.736150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.736382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.736575] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.736688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.736929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.737195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.737461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.738046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.738314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 823), size 597 -> 823

<7> [144.738590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 823 - 2437), size 1162 -> 1614

<7> [144.738800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2437 - 4051), size 2292 -> 1614

<7> [144.739011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.739263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.739533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.739754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.739972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.740292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.740638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.741004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.741311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.741639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.742507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.742804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.768521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.768868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.769104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.769321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.769582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.769780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.769720] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.769968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.770093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.770196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.770396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.770416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.770911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.771123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [144.771323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 823 - 2437) -> ( 597 - 1759), size 1614 -> 1162

<7> [144.771487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2437 - 4051) -> (1759 - 4051), size 1614 -> 2292

<7> [144.771702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.771863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.772062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.772244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.772442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.772726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.772995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.773264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.773550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.773809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.774614] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.774876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.802027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.802330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 597) -> ( 0 - 826), size 597 -> 826

<7> [144.802628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 597 - 1759) -> ( 826 - 2446), size 1162 -> 1620

<7> [144.802729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.802836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1759 - 4051) -> (2446 - 4051), size 2292 -> 1605

<7> [144.803032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.803082] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.803266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.803387] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.803469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.803707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.803905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [144.804172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [144.804431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [144.804756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.805008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [144.805260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [144.806037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.806318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.835144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [144.835569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [144.835670] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.835904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 826 - 2446) -> ( 598 - 1763), size 1620 -> 1165

<7> [144.836148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2446 - 4051) -> (1763 - 4051), size 1605 -> 2288

<7> [144.836113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.836379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.836464] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.836663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.836887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [144.837135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [144.837379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [144.837766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [144.838119] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [144.838436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.838845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [144.839186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [144.840044] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.840347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.868582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 598) -> ( 0 - 2018), size 598 -> 2018

<7> [144.868818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 598 - 1763) -> ( 0 - 0), size 1165 -> 0

<7> [144.869011] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1763 - 4051) -> (2018 - 4051), size 2288 -> 2033

<7> [144.869192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.869366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [144.869578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [144.869759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [144.869718] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.869967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [144.870038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.870159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [144.870329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [144.870322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.870514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [144.870681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.870853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.871028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.871201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.871396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [144.871715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [144.871988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [144.872261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [144.872580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [144.872842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [144.873644] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.873936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.874736] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [144.874987] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]

<7> [144.901859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [144.902168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [144.902401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.902683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.902833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.902889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.903126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.903192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.903345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [144.903523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.903665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [144.903933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [144.904190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [144.904439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [144.904770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [144.905416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.905732] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.935616] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.935803] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471]

<7> [144.935965] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.936266] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.949925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [144.950176] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [144.950387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.950732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [144.950991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [144.951192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [144.951411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [144.951715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [144.951984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [144.952249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [144.952571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [144.952811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [144.953460] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.953735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [144.985067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [144.985261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [144.985433] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [144.985778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [144.985714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [144.985964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [144.986069] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [144.986142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [144.986377] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [144.986369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [144.986699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [144.986953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [144.987205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [144.987467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [144.987755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [144.988483] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [144.988820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.018694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [145.018652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.018908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [145.019036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.019104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.019307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.019362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.019655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.019888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.020105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [145.020398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [145.020720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [145.020986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.021298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.021584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [145.022237] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.022507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.051811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [145.052051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [145.052273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.052602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.052733] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.052824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.053052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.053166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.053281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.053550] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.053642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.054017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.054345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.054680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.054977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.055826] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.056160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.085156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2018), size 1354 -> 2018

<7> [145.085429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2018 - 4051), size 2697 -> 2033

<7> [145.085739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.085870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.085965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.086178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.086246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.086432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.086603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.086742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [145.087083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [145.087361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [145.087706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.087981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.088247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [145.088940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.089244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.118403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [145.118661] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [145.118847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.118788] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.119065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.119147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.119263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.119457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.119459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.119712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.119968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.120220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.120468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.120785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.121046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.121785] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.122044] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.151791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2018), size 1351 -> 2018

<7> [145.151982] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2018 - 4051), size 2700 -> 2033

<7> [145.152155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.152324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.152576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.152657] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.152754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.152936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [145.152998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.153190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [145.153282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.153437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [145.153770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.153998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.154259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [145.154881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.155134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.185005] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [145.185165] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [145.185315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.185465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.185687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.185864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.185833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.186073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.186195] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.186424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [145.186479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.186626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [145.186789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.186975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.187143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.187296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.187459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.187766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.188045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.188323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.188702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.188966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.189732] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.190002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.218635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [145.218652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.218830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [145.219010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.219007] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.219207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.219309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.219379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.219587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.219777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [145.220151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2026), size 1351 -> 2026

<7> [145.220320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1351 - 4051) -> (2026 - 4051), size 2700 -> 2025

<7> [145.220484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.220743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.220906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.221063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.221229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 2

<7> [145.221508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [145.221778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [145.222058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.222354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [145.222666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [145.223345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.223654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.251695] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [145.251925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [145.252129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.252317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.252535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.252559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.252717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.252891] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.252967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.253180] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.253355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [145.253591] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [145.253762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.253917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.254070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.254219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.254375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.254736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [145.254895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [145.255050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.255205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.255359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.255526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.255688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.255934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.256172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.256405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.256741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.256984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.257779] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.258030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.285198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [145.285565] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [145.285704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.285847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.286134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.286217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.286410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.286750] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.286702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.287045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.287308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.287682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.287920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.288332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [145.288593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [145.288813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.289028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.289243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.289459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.289736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.289928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.290118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.290306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.290665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2687), size 1354 -> 2687

<7> [145.290838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1354 - 4051) -> (2687 - 4051), size 2697 -> 1364

<7> [145.291015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.291188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.291354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.291547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.291706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.291868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.292072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.292217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.292850] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.293094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.335024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [145.335278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [145.335536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.335744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.335683] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.335931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.336023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.336143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.336304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.336344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.336642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.336941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.337215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.337551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.337840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.338590] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.338893] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.368675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.369016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.369331] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472]

<7> [145.369303] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.383998] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [145.384265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [145.384523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.384744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.384954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.385202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.385435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.385818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.386158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.386433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.386886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.387139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.387851] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.388110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.418433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [145.418752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [145.418754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.418995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.419262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.419202] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.419527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.419609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.419766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.420011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.420337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.420690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.421058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.421362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.421698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.422631] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.422967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.451907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [145.452107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [145.452288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.452480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.452723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.452919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.452858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.453161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.453217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.453456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.453546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.453774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.454020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.454262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.454523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.455199] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.455459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.485040] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [145.485317] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [145.485655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.485876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.485775] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.486095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.486221] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.486313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.486590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.486639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.486971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.487281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.487691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.487988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.488260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.489037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.489353] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.518371] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2687), size 2026 -> 2687

<7> [145.518590] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (2687 - 4051), size 2025 -> 1364

<7> [145.518756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.518715] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.518917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.519080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.519048] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.519240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.519331] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.519420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.519694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.519937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.520182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.520421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.520691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.521246] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.521478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.551645] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [145.551822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [145.552012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.552176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.552342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.552537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.552679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.552743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.553016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.553022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.553263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.553304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.553519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.553780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.554059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.554641] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.554892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.584963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2687), size 2021 -> 2687

<7> [145.585125] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2687 - 4051), size 2030 -> 1364

<7> [145.585276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.585449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.585680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.585837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.585818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.586025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.586152] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.586278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.586434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.586549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.586789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.587016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.587286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.587938] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.588188] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.618353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [145.618568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [145.618737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.618697] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.618896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.619049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.619039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.619199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.619321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.619371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.619689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.619920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.620145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.620368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.620617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.621363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.621671] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.651903] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2697), size 2021 -> 2697

<7> [145.652113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2021 - 4051) -> (2697 - 4051), size 2030 -> 1354

<7> [145.652304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.652526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.652715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.652650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.652887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.653012] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.653076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2086260 num active planes 2

<7> [145.653314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.653346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [145.653655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [145.653907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.654151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [145.654395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [145.655101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.655348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.684889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [145.685065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [145.685225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.685376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.685573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.685730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.685717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.685950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 2

<7> [145.686047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.686216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [145.686329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.686467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [145.686813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.687043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [145.687302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [145.687965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.688219] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.718644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.719014] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.719434] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473]

<7> [145.719318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.735780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.736084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 2026) -> ( 0 - 583), size 2026 -> 583

<7> [145.736337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 583 - 1736), size 0 -> 1153

<7> [145.736582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2026 - 4051) -> (1736 - 4051), size 2025 -> 2315

<7> [145.736771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.736998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.737190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [145.737396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [145.737663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.737830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.737996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [145.738193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [145.738354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.738521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.738672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.738849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.739052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.739329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [145.739571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [145.739788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.739994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.740187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [145.740936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.741150] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.751340] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]

<7> [145.769933] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474]

<7> [145.785541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.785894] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.786185] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.788537] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.789335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.789768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.818382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.818766] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [145.818738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.819047] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [145.819132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.819310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [145.819532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.819597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.819853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.820165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.820426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.820881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [145.821408] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.821736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [145.822026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [145.822301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [145.822557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.822780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.822986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.823217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.823432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [145.823801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [145.824162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [145.824474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.824825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.825168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [145.825971] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.826270] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.851790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.852099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [145.852320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [145.852609] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [145.852607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.852807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.852904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.852996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.853182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.853177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.853402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.853668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.854076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.854309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [145.854508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [145.854687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [145.854862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.855068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.855241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.855412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.855629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.855904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [145.856179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [145.856448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.856754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.857058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [145.857839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.858131] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.884916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.885244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [145.885603] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [145.885740] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.885819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [145.886017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.886095] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.886206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.886394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.886397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.886638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.886848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [145.887284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.887508] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [145.887676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [145.887845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [145.888014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.888220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [145.888402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [145.888625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [145.888800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [145.889078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [145.889353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [145.889693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.889954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.890244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [145.890962] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.891217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.918539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.918643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.918860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [145.919008] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.919090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [145.919291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [145.919312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.919516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.919708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.919883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.920069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.920263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.920721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.920934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [145.921139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [145.921323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [145.921546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.921712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.921861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [145.922005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [145.922158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.922397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [145.922660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [145.922934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.923181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.923423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [145.924176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.924430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.951592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.951874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [145.952110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [145.952304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [145.952473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.952701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [145.952879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [145.952839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.953088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [145.953171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.953282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [145.953453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.953564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [145.953827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [145.954074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.954324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [145.954573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [145.955248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.955527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [145.984889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [145.985119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 583), size 376 -> 583

<7> [145.985289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 583 - 1736), size 740 -> 1153

<7> [145.985458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (1736 - 4051), size 2935 -> 2315

<7> [145.985693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [145.985864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [145.985828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [145.986068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [145.986160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [145.986248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [145.986445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [145.986444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [145.986741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [145.986992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [145.987237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.987546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [145.987786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [145.988699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [145.988944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.001883] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.034833] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.035070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [146.035250] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [146.035422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [146.035652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.035838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.035782] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.036001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.036160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.036115] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.036341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [146.036399] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.036628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [146.036882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [146.037134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.037382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.037686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [146.038322] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.038609] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.068216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.068429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 583), size 375 -> 583

<7> [146.068696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 583 - 1736), size 738 -> 1153

<7> [146.068872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1736 - 4051), size 2938 -> 2315

<7> [146.068829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.069071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.069187] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.069248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.069418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.069470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.069622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.069807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [146.070043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [146.070278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [146.070557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [146.070787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [146.071015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [146.071733] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.071989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.101599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.101821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [146.101995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 583 - 1736) -> ( 375 - 1113), size 1153 -> 738

<7> [146.102158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1736 - 4051) -> (1113 - 4051), size 2315 -> 2938

<7> [146.102318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.102478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.102710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.102869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.102856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.103046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [146.103166] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.103283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [146.103436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.103531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [146.103765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.104033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.104271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [146.105008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.105265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.135138] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.135399] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 375) -> ( 0 - 585), size 375 -> 585

<7> [146.135653] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 375 - 1113) -> ( 585 - 1743), size 738 -> 1158

<7> [146.135848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1113 - 4051) -> (1743 - 4051), size 2938 -> 2308

<7> [146.135784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.136059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.136168] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.136240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.136421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.136540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.136654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.136898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1738550 num active planes 3

<7> [146.137188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [146.137474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [146.137832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [146.138172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [146.138502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [146.139236] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.139520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.168157] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.168361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [146.168561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 585 - 1743) -> ( 376 - 1116), size 1158 -> 740

<7> [146.168717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1743 - 4051) -> (1116 - 4051), size 2308 -> 2935

<7> [146.168703] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.168877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.169030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.169052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.169197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [146.169364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [146.169335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.169566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2433970 num active planes 3

<7> [146.169813] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [146.170062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [146.170302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.170538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [146.170766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [146.171538] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.171791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.202662] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475]

<7> [146.202639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.202973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.203272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.224070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.224310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 376) -> ( 0 - 814), size 376 -> 814

<7> [146.224464] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 376 - 1116) -> ( 814 - 2425), size 740 -> 1611

<7> [146.224651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1116 - 4051) -> (2425 - 4051), size 2935 -> 1626

<7> [146.224788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.224918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.225043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.225178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.225310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.225419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.225560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.225663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.225763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.225861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.225959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.226051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.226162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.226312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.226456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.226619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.226759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.226896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.227456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.227614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.235948] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476]

<7> [146.250900] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.284905] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.285233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [146.285547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [146.285554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.285761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [146.285924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.285982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.286193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.286265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.286402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.286686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.286945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.287283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.287636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.287985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.288342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.288719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.289660] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.290047] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.318381] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.318801] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [146.318887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.319053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [146.319273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [146.319272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.319513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.319631] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.319721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.319916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.320142] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.320362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.320815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.321043] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [146.321271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [146.321449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [146.321672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.321842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.322010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.322177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.322350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.322655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.322916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.323177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.323429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.323744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.324573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.324839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.351632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.351938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [146.352156] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [146.352358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [146.352597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.352781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.352723] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.352957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.353056] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.353165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.353341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.353384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.353778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.353974] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [146.354130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [146.354291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [146.354438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.354680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.354834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.354988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.355152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.355411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.355698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.355940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.356174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.356449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.357224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.357504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.385096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.385380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [146.385630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [146.385738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.385820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [146.386006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.386092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.386191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.386370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.386378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.386577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.386819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.387173] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.387367] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [146.387556] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [146.387735] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [146.387897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.388058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.388220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.388382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.388583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.388874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.389110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.389347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.389622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.389877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.390649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.390920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.418230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.418658] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [146.418710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.418908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [146.419129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [146.419094] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.419341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.419419] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.419597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.419800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [146.420041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [146.420293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.420829] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.421085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [146.421319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [146.421533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [146.421726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.421971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.422177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [146.422376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [146.422623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.422930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.423221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.423583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.423899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.424183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.425019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.425317] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.451560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.451857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [146.452111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [146.452300] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [146.452507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.452687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.452651] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.452864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.452985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.453051] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.453242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.453269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.453702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.453918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 814), size 588 -> 814

<7> [146.454097] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 814 - 2425), size 1158 -> 1611

<7> [146.454272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> (2425 - 4051), size 2305 -> 1626

<7> [146.454448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.454708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.454894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.455087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.455274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.455595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.455928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.456215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.456521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.456805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.457847] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.458177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.468345] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.501468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.501798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [146.502044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [146.502239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [146.502427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.502698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.502881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.502822] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.503056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.503155] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.503255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.503436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.503579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.503842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.504106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.504415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.504713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.505309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.505600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.534817] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.535062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 814), size 586 -> 814

<7> [146.535276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 814 - 2425), size 1156 -> 1611

<7> [146.535450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2425 - 4051), size 2309 -> 1626

<7> [146.535683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.535861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [146.535827] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.536067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [146.536169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.536240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [146.536427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.536450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.536718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.536959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.537243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.537511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.537745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.538558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.538826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.568122] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.568362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [146.568584] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 814 - 2425) -> ( 586 - 1742), size 1611 -> 1156

<7> [146.568754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2425 - 4051) -> (1742 - 4051), size 1626 -> 2309

<7> [146.568701] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.568916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.569082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [146.569028] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.569245] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [146.569313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.569442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [146.569704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.569970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.570217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.570527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.570814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.571066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.571784] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.572056] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.601664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.601911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 586) -> ( 0 - 817), size 586 -> 817

<7> [146.602087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 586 - 1742) -> ( 817 - 2434), size 1156 -> 1617

<7> [146.602255] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1742 - 4051) -> (2434 - 4051), size 2309 -> 1617

<7> [146.602454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.602705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.602821] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.602885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [146.603087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [146.603157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.603273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 2781680 num active planes 3

<7> [146.603442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.603539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [146.603792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [146.604046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.604309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [146.604606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [146.605307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.605563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.634792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.635037] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [146.635206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 817 - 2434) -> ( 588 - 1746), size 1617 -> 1158

<7> [146.635368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (2434 - 4051) -> (1746 - 4051), size 1617 -> 2305

<7> [146.635619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.635787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [146.635755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.635952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [146.636116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [146.636108] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.636301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 3477100 num active planes 3

<7> [146.636393] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.636568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [146.636826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [146.637062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.637325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [146.637568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [146.638224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.638506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.668082] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [146.668371] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000

<7> [146.668654] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000

<7> [146.668794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.668909] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [146.669112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.669147] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]

<7> [146.669378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [146.669413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:33:plane 1A] using Y plane [PLANE:123:plane 4A]

<7> [146.669699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]

<7> [146.669936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [146.670161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [146.670385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [146.670639] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [146.670882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [146.671101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [146.671319] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [146.671550] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [146.671766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [146.671981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [146.672195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled

<7> [146.672423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [146.672684] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [146.672898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14

<7> [146.673108] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [146.673318] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [146.673547] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [146.673759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [146.673973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [146.674184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [146.674396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [146.674645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [146.674871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [146.675124] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [146.675385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [146.675630] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [146.675845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [146.676053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [146.676304] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [146.676548] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [146.676780] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [146.676982] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [146.677184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [146.677388] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [146.677658] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,

<7> [146.677871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [146.678074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [146.678276] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [146.678491] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [146.678693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [146.678892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [146.679089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [146.679283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [146.679467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [146.679695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [146.679882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [146.680062] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.680238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.680403] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.680592] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [146.680777] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [146.680940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.681095] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.681244] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [146.681395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [146.681574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [146.681731] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: yes

<7> [146.681884] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [146.682048] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+0.000000+0.000000 dst: 96x120+0+0

<7> [146.682198] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [FB:476] 128x192 format = P010 little-endian (0x30313050) modifier = 0x100000000000009, visible: no

<7> [146.682334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [146.682467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [FB:442] 128x192 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes

<7> [146.682628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x4, scaler: -1, scaling_filter: 0

<7> [146.682760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 96.000000x120.000000+32.000000+0.000000 dst: 96x120+2784+0

<7> [146.682922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [146.683068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [146.683265] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1

<7> [146.683400] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on

<7> [146.683578] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [146.684501] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [146.685712] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]

<7> [146.685829] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]

<7> [146.688107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 588) -> ( 0 - 0), size 588 -> 0

<7> [146.688186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 588 - 1746) -> ( 0 - 0), size 1158 -> 0

<7> [146.688248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb (1746 - 4051) -> ( 0 - 0), size 2305 -> 0

<7> [146.688305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [146.688356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [146.688642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [146.688885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.688988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [146.689047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0

<7> [146.689131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [146.689211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [146.689289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [146.689366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [146.689446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [146.689718] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<6> [146.704516] [IGT] kms_rotation_crc: finished subtest multiplane-rotation-cropping-top, SUCCESS

<7> [146.705051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051

<7> [146.705133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [146.705200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [146.705264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87

<7> [146.705327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88

<7> [146.705399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1

<7> [146.705512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [146.705622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [146.705748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [146.705848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [146.705939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [146.717849] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2

<7> [146.719404] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<6> [146.720026] [IGT] kms_rotation_crc: exiting, ret=0

<6> [146.735235] Console: switching to colour frame buffer device 180x56

<7> [146.785639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [146.786005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [146.786288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

Results for igt@kms_rotation_crc@multiplane-rotation-cropping-top