<5>[ 0.000000] Linux version 6.18.0-rc6-lgci-xe-xe-4121-91fc6d984707c9bfd+ (builder@lgci) (gcc (Ubuntu 13.3.0-6ubuntu2~24.04) 13.3.0, GNU ld (GNU Binutils for Ubuntu) 2.42) #1 SMP PREEMPT_DYNAMIC Mon Nov 17 23:52:57 UTC 2025 <6>[ 0.000000] Command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <6>[ 0.000000] KERNEL supported cpus: <6>[ 0.000000] Intel GenuineIntel <6>[ 0.000000] AMD AuthenticAMD <6>[ 0.000000] Hygon HygonGenuine <6>[ 0.000000] Centaur CentaurHauls <6>[ 0.000000] zhaoxin Shanghai <6>[ 0.000000] x86/tme: not enabled by BIOS <6>[ 0.000000] x86/split lock detection: #AC: crashing the kernel on kernel split_locks and warning on user-space split_locks <6>[ 0.000000] BIOS-provided physical RAM map: <6>[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x00000000000fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006cac0fff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000006cac1000-0x000000006fe67fff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x000000006fe68000-0x000000006ff4ffff] ACPI NVS <6>[ 0.000000] BIOS-e820: [mem 0x000000006ff50000-0x000000006fffefff] ACPI data <6>[ 0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable <6>[ 0.000000] BIOS-e820: [mem 0x0000000070000000-0x00000000807fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000c0000000-0x00000000cfffffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fed7ffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000ff200000-0x00000001044fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000104500000-0x000000087f7fffff] usable <6>[ 0.000000] NX (Execute Disable) protection: active <6>[ 0.000000] APIC: Static calls initialized <6>[ 0.000000] efi: EFI v2.7 by Intel <6>[ 0.000000] efi: ACPI=0x6fffe000 ACPI 2.0=0x6fffe014 SMBIOS=0x6cbc7000 MEMATTR=0x69916018 ESRT=0x68ff8518 MOKvar=0x6ccfb000 <6>[ 0.000000] efi: Remove mem260: MMIO range=[0xc0000000-0xcfffffff] (256MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xc0000000-0xcfffffff] reserved <6>[ 0.000000] efi: Remove mem262: MMIO range=[0xff200000-0xffffffff] (14MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xff200000-0xffffffff] reserved <6>[ 0.000000] SMBIOS 3.8 present. <6>[ 0.000000] DMI: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D99.2508051732 08/05/2025 <6>[ 0.000000] DMI: Memory slots populated: 8/8 <6>[ 0.000000] tsc: Detected 3100.000 MHz processor <6>[ 0.000000] tsc: Detected 3110.400 MHz TSC <7>[ 0.000009] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved <7>[ 0.000011] e820: remove [mem 0x000a0000-0x000fffff] usable <6>[ 0.000014] last_pfn = 0x87f800 max_arch_pfn = 0x400000000 <6>[ 0.000018] MTRR map: 6 entries (3 fixed + 3 variable; max 23), built from 10 variable MTRRs <6>[ 0.000019] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT <6>[ 0.000385] x2apic: enabled by BIOS, switching to x2apic ops <6>[ 0.000386] last_pfn = 0x70000 max_arch_pfn = 0x400000000 <6>[ 0.004882] esrt: Reserving ESRT space from 0x0000000068ff8518 to 0x0000000068ff8668. <7>[ 0.004890] e820: update [mem 0x68ff8000-0x68ff8fff] usable ==> reserved <6>[ 0.004907] Using GB pages for direct mapping <6>[ 0.005538] printk: log buffer data + meta data: 1048576 + 3670016 = 4718592 bytes <6>[ 0.005539] printk: early log buf free: 258816(98%) <6>[ 0.005540] Secure boot disabled <6>[ 0.005542] ACPI: Early table checksum verification disabled <6>[ 0.005544] ACPI: RSDP 0x000000006FFFE014 000024 (v02 INTEL ) <6>[ 0.005547] ACPI: XSDT 0x000000006FF70228 000194 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005551] ACPI: FACP 0x000000006FFAA000 000114 (v06 INTEL LNL 00000002 01000013) <6>[ 0.005554] ACPI: DSDT 0x000000006FFB6000 02555F (v02 INTEL LNL 00000002 01000013) <6>[ 0.005555] ACPI: FACS 0x000000006FEF1000 000040 <6>[ 0.005557] ACPI: SSDT 0x000000006FFFC000 000388 (v02 PmaxDv Pmax_Dev 00000001 INTL 20210930) <6>[ 0.005558] ACPI: SSDT 0x000000006FFFB000 0006AA (v02 PmRef Cpu0Ist 00003000 INTL 20210930) <6>[ 0.005560] ACPI: SSDT 0x000000006FFFA000 0005FB (v02 PmRef Cpu0Hwp 00003000 INTL 20210930) <6>[ 0.005561] ACPI: SSDT 0x000000006FFF9000 0001AB (v02 PmRef Cpu0Psd 00003000 INTL 20210930) <6>[ 0.005562] ACPI: SSDT 0x000000006FFF8000 000394 (v02 PmRef Cpu0Cst 00003001 INTL 20210930) <6>[ 0.005564] ACPI: SSDT 0x000000006FFF6000 001BAF (v02 PmRef ApIst 00003000 INTL 20210930) <6>[ 0.005565] ACPI: SSDT 0x000000006FFF4000 001620 (v02 PmRef ApHwp 00003000 INTL 20210930) <6>[ 0.005566] ACPI: SSDT 0x000000006FFF2000 001349 (v02 PmRef ApPsd 00003000 INTL 20210930) <6>[ 0.005568] ACPI: SSDT 0x000000006FFF1000 000FBB (v02 PmRef ApCst 00003000 INTL 20210930) <6>[ 0.005569] ACPI: SSDT 0x000000006FFED000 003BD7 (v02 CpuRef CpuSsdt 00003000 INTL 20210930) <6>[ 0.005570] ACPI: DTPR 0x000000006FFEC000 000090 (v01 00000000 00000000) <6>[ 0.005572] ACPI: SSDT 0x000000006FFEB000 000FE2 (v02 INTEL PDatTabl 00001000 INTL 20210930) <6>[ 0.005573] ACPI: SSDT 0x000000006FFE8000 002450 (v02 INTEL IgfxSsdt 00003000 INTL 20210930) <6>[ 0.005574] ACPI: SSDT 0x000000006FFE7000 0000A5 (v02 INTEL TseSsdt 00001000 INTL 20210930) <6>[ 0.005576] ACPI: SSDT 0x000000006FFDD000 009176 (v02 INTEL TcssSsdt 00001000 INTL 20210930) <6>[ 0.005577] ACPI: SSDT 0x000000006FFDC000 0000E0 (v02 INTEL IpuSsdt 00001000 INTL 20210930) <6>[ 0.005578] ACPI: SSDT 0x000000006FFB1000 004AC3 (v02 INTEL LnlMRvp1 00001000 INTL 20210930) <6>[ 0.005580] ACPI: SSDT 0x000000006FFAF000 00140F (v02 INTEL I2Pm_Rvp 00001000 INTL 20210930) <6>[ 0.005581] ACPI: SSDT 0x000000006FFAB000 003956 (v02 INTEL Ther_Rvp 00001000 INTL 20210930) <6>[ 0.005582] ACPI: HPET 0x000000006FFA9000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005583] ACPI: WSMT 0x000000006FFFD000 000028 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005585] ACPI: APIC 0x000000006FFA7000 0000D8 (v06 INTEL LNL 00000000 01000013) <6>[ 0.005586] ACPI: MCFG 0x000000006FFA6000 00003C (v01 INTEL LNL 00000002 01000013) <6>[ 0.005587] ACPI: SSDT 0x000000006FFA5000 0006E3 (v02 INTEL PepoSsdt 00001000 INTL 20210930) <6>[ 0.005588] ACPI: SSDT 0x000000006FF9F000 005321 (v02 DptfTb DptfTabl 00001000 INTL 20210930) <6>[ 0.005590] ACPI: SSDT 0x000000006FF94000 00A46A (v02 MiCaTb MiCaTabl 00001000 INTL 20210930) <6>[ 0.005591] ACPI: SSDT 0x000000006FF86000 00D816 (v02 INTEL Cnv_Ssdt 00001000 INTL 20210930) <6>[ 0.005592] ACPI: LPIT 0x000000006FF85000 0000CC (v01 INTEL LNL 00000002 01000013) <6>[ 0.005594] ACPI: SSDT 0x000000006FF84000 000D5C (v02 INTEL PtidDevc 00001000 INTL 20210930) <6>[ 0.005595] ACPI: SSDT 0x000000006FF83000 0001F0 (v02 INTEL TbtTypeC 00000000 INTL 20210930) <6>[ 0.005596] ACPI: DBGP 0x000000006FF82000 000034 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005598] ACPI: DBG2 0x000000006FF81000 000054 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005599] ACPI: NHLT 0x000000006FF80000 0002E3 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005600] ACPI: SSDT 0x000000006FF7E000 00115C (v02 INTEL UsbCTabl 00001000 INTL 20210930) <6>[ 0.005601] ACPI: SSDT 0x000000006FF77000 00653B (v02 INTEL EcSsdt 00000000 INTL 20210930) <6>[ 0.005603] ACPI: ECDT 0x000000006FF76000 000069 (v01 LNL 00000002 01000013) <6>[ 0.005604] ACPI: DMAR 0x000000006FF75000 0000D8 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005605] ACPI: FPDT 0x000000006FF74000 000044 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005607] ACPI: SSDT 0x000000006FF73000 00086D (v02 INTEL xh_lnl_m 00000000 INTL 20210930) <6>[ 0.005608] ACPI: SSDT 0x000000006FF71000 0013DB (v02 SocGpe SocGpe 00003000 INTL 20210930) <6>[ 0.005609] ACPI: SSDT 0x000000006FF6D000 002463 (v02 SocCmn SocCmn 00003000 INTL 20210930) <6>[ 0.005611] ACPI: SDEV 0x000000006FFA8000 000046 (v01 00000000 00000000) <6>[ 0.005612] ACPI: SSDT 0x000000006FF62000 00A4FA (v02 INTEL St09Ssdt 00001000 INTL 20210930) <6>[ 0.005613] ACPI: PHAT 0x000000006FF61000 0007C0 (v01 INTEL LNL 00000005 MSFT 0100000D) <6>[ 0.005614] ACPI: BGRT 0x000000006FF60000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005615] ACPI: Reserving FACP table memory at [mem 0x6ffaa000-0x6ffaa113] <6>[ 0.005616] ACPI: Reserving DSDT table memory at [mem 0x6ffb6000-0x6ffdb55e] <6>[ 0.005617] ACPI: Reserving FACS table memory at [mem 0x6fef1000-0x6fef103f] <6>[ 0.005617] ACPI: Reserving SSDT table memory at [mem 0x6fffc000-0x6fffc387] <6>[ 0.005617] ACPI: Reserving SSDT table memory at [mem 0x6fffb000-0x6fffb6a9] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fffa000-0x6fffa5fa] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fff9000-0x6fff91aa] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fff8000-0x6fff8393] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff6000-0x6fff7bae] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff4000-0x6fff561f] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff2000-0x6fff3348] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff1000-0x6fff1fba] <6>[ 0.005620] ACPI: Reserving SSDT table memory at [mem 0x6ffed000-0x6fff0bd6] <6>[ 0.005620] ACPI: Reserving DTPR table memory at [mem 0x6ffec000-0x6ffec08f] <6>[ 0.005620] ACPI: Reserving SSDT table memory at [mem 0x6ffeb000-0x6ffebfe1] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffe8000-0x6ffea44f] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffe7000-0x6ffe70a4] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffdd000-0x6ffe6175] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffdc000-0x6ffdc0df] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffb1000-0x6ffb5ac2] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffaf000-0x6ffb040e] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffab000-0x6ffae955] <6>[ 0.005623] ACPI: Reserving HPET table memory at [mem 0x6ffa9000-0x6ffa9037] <6>[ 0.005623] ACPI: Reserving WSMT table memory at [mem 0x6fffd000-0x6fffd027] <6>[ 0.005623] ACPI: Reserving APIC table memory at [mem 0x6ffa7000-0x6ffa70d7] <6>[ 0.005624] ACPI: Reserving MCFG table memory at [mem 0x6ffa6000-0x6ffa603b] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ffa5000-0x6ffa56e2] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ff9f000-0x6ffa4320] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ff94000-0x6ff9e469] <6>[ 0.005625] ACPI: Reserving SSDT table memory at [mem 0x6ff86000-0x6ff93815] <6>[ 0.005625] ACPI: Reserving LPIT table memory at [mem 0x6ff85000-0x6ff850cb] <6>[ 0.005625] ACPI: Reserving SSDT table memory at [mem 0x6ff84000-0x6ff84d5b] <6>[ 0.005626] ACPI: Reserving SSDT table memory at [mem 0x6ff83000-0x6ff831ef] <6>[ 0.005626] ACPI: Reserving DBGP table memory at [mem 0x6ff82000-0x6ff82033] <6>[ 0.005626] ACPI: Reserving DBG2 table memory at [mem 0x6ff81000-0x6ff81053] <6>[ 0.005627] ACPI: Reserving NHLT table memory at [mem 0x6ff80000-0x6ff802e2] <6>[ 0.005627] ACPI: Reserving SSDT table memory at [mem 0x6ff7e000-0x6ff7f15b] <6>[ 0.005627] ACPI: Reserving SSDT table memory at [mem 0x6ff77000-0x6ff7d53a] <6>[ 0.005627] ACPI: Reserving ECDT table memory at [mem 0x6ff76000-0x6ff76068] <6>[ 0.005628] ACPI: Reserving DMAR table memory at [mem 0x6ff75000-0x6ff750d7] <6>[ 0.005628] ACPI: Reserving FPDT table memory at [mem 0x6ff74000-0x6ff74043] <6>[ 0.005628] ACPI: Reserving SSDT table memory at [mem 0x6ff73000-0x6ff7386c] <6>[ 0.005629] ACPI: Reserving SSDT table memory at [mem 0x6ff71000-0x6ff723da] <6>[ 0.005629] ACPI: Reserving SSDT table memory at [mem 0x6ff6d000-0x6ff6f462] <6>[ 0.005629] ACPI: Reserving SDEV table memory at [mem 0x6ffa8000-0x6ffa8045] <6>[ 0.005630] ACPI: Reserving SSDT table memory at [mem 0x6ff62000-0x6ff6c4f9] <6>[ 0.005630] ACPI: Reserving PHAT table memory at [mem 0x6ff61000-0x6ff617bf] <6>[ 0.005630] ACPI: Reserving BGRT table memory at [mem 0x6ff60000-0x6ff60037] <6>[ 0.005701] APIC: Switched APIC routing to: cluster x2apic <6>[ 0.005901] No NUMA configuration found <6>[ 0.005901] Faking a node at [mem 0x0000000000000000-0x000000087f7fffff] <6>[ 0.005907] NODE_DATA(0) allocated [mem 0x87f352e40-0x87f37dfff] <6>[ 0.006023] Zone ranges: <6>[ 0.006023] DMA [mem 0x0000000000001000-0x0000000000ffffff] <6>[ 0.006024] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] <6>[ 0.006025] Normal [mem 0x0000000100000000-0x000000087f7fffff] <6>[ 0.006026] Device empty <6>[ 0.006026] Movable zone start for each node <6>[ 0.006027] Early memory node ranges <6>[ 0.006027] node 0: [mem 0x0000000000001000-0x000000000009efff] <6>[ 0.006028] node 0: [mem 0x0000000000100000-0x000000006cac0fff] <6>[ 0.006029] node 0: [mem 0x000000006ffff000-0x000000006fffffff] <6>[ 0.006029] node 0: [mem 0x0000000104500000-0x000000087f7fffff] <6>[ 0.006030] Initmem setup node 0 [mem 0x0000000000001000-0x000000087f7fffff] <6>[ 0.006035] On node 0, zone DMA: 1 pages in unavailable ranges <6>[ 0.006050] On node 0, zone DMA: 97 pages in unavailable ranges <6>[ 0.007648] On node 0, zone DMA32: 13630 pages in unavailable ranges <6>[ 0.035542] On node 0, zone Normal: 17664 pages in unavailable ranges <6>[ 0.035550] On node 0, zone Normal: 2048 pages in unavailable ranges <6>[ 0.036035] ACPI: PM-Timer IO Port: 0x1808 <6>[ 0.036043] ACPI: X2APIC_NMI (uid[0xffffffff] high level lint[0x1]) <6>[ 0.036093] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 <6>[ 0.036095] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <6>[ 0.036097] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <6>[ 0.036099] ACPI: Using ACPI (MADT) for SMP configuration information <6>[ 0.036100] ACPI: HPET id: 0x8086a701 base: 0xfed00000 <7>[ 0.036111] e820: update [mem 0x6992d000-0x69947fff] usable ==> reserved <6>[ 0.036117] TSC deadline timer available <6>[ 0.036119] CPU topo: Max. logical packages: 1 <6>[ 0.036119] CPU topo: Max. logical dies: 1 <6>[ 0.036120] CPU topo: Max. dies per package: 1 <6>[ 0.036121] CPU topo: Max. threads per core: 1 <6>[ 0.036121] CPU topo: Num. cores per package: 8 <6>[ 0.036122] CPU topo: Num. threads per package: 8 <6>[ 0.036122] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs <6>[ 0.036134] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] <6>[ 0.036136] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] <6>[ 0.036137] PM: hibernation: Registered nosave memory: [mem 0x68ff8000-0x68ff8fff] <6>[ 0.036138] PM: hibernation: Registered nosave memory: [mem 0x6992d000-0x69947fff] <6>[ 0.036138] PM: hibernation: Registered nosave memory: [mem 0x6cac1000-0x6fffefff] <6>[ 0.036139] PM: hibernation: Registered nosave memory: [mem 0x70000000-0x1044fffff] <6>[ 0.036141] [mem 0x80800000-0xfed1ffff] available for PCI devices <6>[ 0.036141] Booting paravirtualized kernel on bare hardware <6>[ 0.036143] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns <6>[ 0.036151] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1 <6>[ 0.036479] percpu: Embedded 86 pages/cpu s229376 r8192 d114688 u524288 <7>[ 0.036483] pcpu-alloc: s229376 r8192 d114688 u524288 alloc=1*2097152 <7>[ 0.036485] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 <5>[ 0.036498] Kernel command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <7>[ 0.036593] blacklisting initcall simpledrm_platform_driver_init <5>[ 0.036609] random: crng init done <6>[ 0.038451] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) <6>[ 0.039374] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) <6>[ 0.039436] software IO TLB: area num 8. <6>[ 0.046792] Fallback order for Node 0: 0 <6>[ 0.046796] Built 1 zonelists, mobility grouping on. Total pages: 8289632 <6>[ 0.046796] Policy zone: Normal <6>[ 0.046805] mem auto-init: stack:off, heap alloc:on, heap free:off <6>[ 0.046806] stackdepot: allocating hash table via alloc_large_system_hash <6>[ 0.046809] stackdepot hash table entries: 1048576 (order: 12, 16777216 bytes, linear) <6>[ 0.047725] stackdepot: allocating space for 8192 stack pools via memblock <4>[ 0.080233] ********************************************************** <4>[ 0.080235] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.080235] ** ** <4>[ 0.080235] ** This system shows unhashed kernel memory addresses ** <4>[ 0.080235] ** via the console, logs, and other interfaces. This ** <4>[ 0.080236] ** might reduce the security of your system. ** <4>[ 0.080236] ** ** <4>[ 0.080236] ** If you see this message and you are not debugging ** <4>[ 0.080236] ** the kernel, report this immediately to your system ** <4>[ 0.080236] ** administrator! ** <4>[ 0.080237] ** ** <4>[ 0.080237] ** Use hash_pointers=always to force this mode off ** <4>[ 0.080237] ** ** <4>[ 0.080237] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.080237] ********************************************************** <6>[ 0.081320] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 <6>[ 0.089568] ftrace: allocating 60599 entries in 240 pages <6>[ 0.089570] ftrace: allocated 240 pages with 4 groups <6>[ 0.090980] Dynamic Preempt: voluntary <6>[ 0.091477] Running RCU self tests <6>[ 0.091477] Running RCU synchronous self tests <6>[ 0.091478] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.091478] rcu: RCU lockdep checking is enabled. <6>[ 0.091478] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8. <6>[ 0.091479] Trampoline variant of Tasks RCU enabled. <6>[ 0.091479] Rude variant of Tasks RCU enabled. <6>[ 0.091479] Tracing variant of Tasks RCU enabled. <6>[ 0.091480] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. <6>[ 0.091480] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 <6>[ 0.091546] Running RCU synchronous self tests <6>[ 0.091552] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.091555] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.091558] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.101893] NR_IRQS: 524544, nr_irqs: 2048, preallocated irqs: 16 <6>[ 0.102364] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.102788] Console: colour dummy device 80x25 <6>[ 0.102797] printk: legacy console [tty0] enabled <6>[ 0.103966] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <6>[ 0.103973] ... MAX_LOCKDEP_SUBCLASSES: 8 <6>[ 0.103977] ... MAX_LOCK_DEPTH: 48 <6>[ 0.103981] ... MAX_LOCKDEP_KEYS: 8192 <6>[ 0.103984] ... CLASSHASH_SIZE: 4096 <6>[ 0.103988] ... MAX_LOCKDEP_ENTRIES: 524288 <6>[ 0.103992] ... MAX_LOCKDEP_CHAINS: 524288 <6>[ 0.103995] ... CHAINHASH_SIZE: 262144 <6>[ 0.103999] memory used by lock dependency info: 54145 kB <6>[ 0.104003] memory used for stack traces: 4224 kB <6>[ 0.104007] per task-struct memory footprint: 1920 bytes <6>[ 0.104056] ACPI: Core revision 20250807 <6>[ 0.104923] hpet: HPET dysfunctional in PC10. Force disabled. <6>[ 0.104987] APIC: Switch to symmetric I/O mode setup <6>[ 0.104993] DMAR: Host address width 38 <6>[ 0.104996] DMAR: DRHD base: 0x000000fc800000 flags: 0x0 <6>[ 0.105026] DMAR: dmar0: reg_base_addr fc800000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.105060] DMAR: DRHD base: 0x000000fc810000 flags: 0x0 <6>[ 0.105079] DMAR: dmar1: reg_base_addr fc810000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.105105] DMAR: DRHD base: 0x000000fc820000 flags: 0x1 <6>[ 0.105126] DMAR: dmar2: reg_base_addr fc820000 ver 7:1 cap e9de008cee690402 ecap 1ac89800f0efda <6>[ 0.105160] DMAR: SATC flags: 0x1 <6>[ 0.105170] DMAR-IR: IOAPIC id 2 under DRHD base 0xfc820000 IOMMU 2 <6>[ 0.105175] DMAR-IR: HPET id 0 under DRHD base 0xfc820000 <6>[ 0.105179] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping. <6>[ 0.107221] DMAR-IR: Enabled IRQ remapping in x2apic mode <6>[ 0.112384] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 0.112402] Calibrating delay loop (skipped), value calculated using timer frequency.. 6220.80 BogoMIPS (lpj=3110400) <6>[ 0.112478] CPU0: Thermal monitoring enabled (TM1) <6>[ 0.112484] x86/cpu: User Mode Instruction Prevention (UMIP) activated <6>[ 0.112667] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 <6>[ 0.112671] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 <6>[ 0.112680] mitigations: Enabled attack vectors: user_kernel, user_user, guest_host, guest_guest, SMT mitigations: auto <6>[ 0.112692] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl <6>[ 0.112699] Spectre V2 : Mitigation: Enhanced / Automatic IBRS <6>[ 0.112703] VMSCAPE: Mitigation: IBPB before exit to userspace <6>[ 0.112708] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization <6>[ 0.112715] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier <6>[ 0.112730] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' <6>[ 0.112736] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' <6>[ 0.112741] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' <6>[ 0.112745] x86/fpu: Supporting XSAVE feature 0x200: 'Protection Keys User registers' <6>[ 0.112751] x86/fpu: Supporting XSAVE feature 0x800: 'Control-flow User registers' <6>[ 0.112756] x86/fpu: Supporting XSAVE feature 0x1000: 'Control-flow Kernel registers (KVM only)' <6>[ 0.112763] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 <6>[ 0.112768] x86/fpu: xstate_offset[9]: 832, xstate_sizes[9]: 8 <6>[ 0.112772] x86/fpu: xstate_offset[11]: 840, xstate_sizes[11]: 16 <6>[ 0.112777] x86/fpu: xstate_offset[12]: 856, xstate_sizes[12]: 24 <6>[ 0.112782] x86/fpu: Enabled xstate features 0x1a07, context size is 880 bytes, using 'compacted' format. <6>[ 0.113396] Freeing SMP alternatives memory: 56K <6>[ 0.113396] pid_max: default: 32768 minimum: 301 <6>[ 0.113396] LSM: initializing lsm=capability,landlock,yama,apparmor,ima,evm <6>[ 0.113396] landlock: Up and running. <6>[ 0.113396] Yama: becoming mindful. <6>[ 0.113396] AppArmor: AppArmor initialized <6>[ 0.113396] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.113396] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.113396] Running RCU synchronous self tests <6>[ 0.113396] Running RCU synchronous self tests <6>[ 0.113396] smpboot: CPU0: Intel(R) Core(TM) Ultra 5 238V (family: 0x6, model: 0xbd, stepping: 0x1) <6>[ 0.113396] Performance Events: XSAVE Architectural LBR, PEBS fmt6+-baseline, AnyThread deprecated, Lunarlake Hybrid events, 32-deep LBR, full-width counters, Intel PMU driver. <6>[ 0.113396] core: cpu_core PMU driver: <6>[ 0.113396] ... version: 6 <6>[ 0.113396] ... bit width: 48 <6>[ 0.113396] ... generic counters: 10 <6>[ 0.113396] ... generic bitmap: 00000000000003ff <6>[ 0.113396] ... fixed-purpose counters: 4 <6>[ 0.113396] ... fixed-purpose bitmap: 000000000000000f <6>[ 0.113396] ... value mask: 0000ffffffffffff <6>[ 0.113396] ... max period: 00007fffffffffff <6>[ 0.113396] ... global_ctrl mask: 0001000f000003ff <6>[ 0.113456] signal: max sigframe size: 3632 <6>[ 0.113480] Estimated ratio of average max frequency by base frequency (times 1024): 1189 <6>[ 0.113579] rcu: Hierarchical SRCU implementation. <6>[ 0.113584] rcu: Max phase no-delay instances is 400. <6>[ 0.113726] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.115582] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. <6>[ 0.115847] smp: Bringing up secondary CPUs ... <6>[ 0.116197] smpboot: x86: Booting SMP configuration: <6>[ 0.116204] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 <6>[ 0.010844] core: cpu_atom PMU driver: <6>[ 0.010844] ... version: 6 <6>[ 0.010844] ... bit width: 48 <6>[ 0.010844] ... generic counters: 8 <6>[ 0.010844] ... generic bitmap: 00000000000000ff <6>[ 0.010844] ... fixed-purpose counters: 6 <6>[ 0.010844] ... fixed-purpose bitmap: 0000000000000077 <6>[ 0.010844] ... value mask: 0000ffffffffffff <6>[ 0.010844] ... max period: 00007fffffffffff <6>[ 0.010844] ... global_ctrl mask: 00000077000000ff <6>[ 0.121524] smp: Brought up 1 node, 8 CPUs <6>[ 0.122565] smpboot: Total of 8 processors activated (49766.40 BogoMIPS) <6>[ 0.124500] Memory: 32358416K/33158528K available (25421K kernel code, 5652K rwdata, 9540K rodata, 5704K init, 68232K bss, 777192K reserved, 0K cma-reserved) <6>[ 0.126245] devtmpfs: initialized <6>[ 0.126583] x86/mm: Memory block size: 128MB <6>[ 0.149447] ACPI: PM: Registering ACPI NVS region [mem 0x6fe68000-0x6ff4ffff] (950272 bytes) <6>[ 0.149963] Running RCU synchronous self tests <6>[ 0.149976] Running RCU synchronous self tests <6>[ 0.150657] Running RCU Tasks wait API self tests <6>[ 0.151407] Running RCU Tasks Rude wait API self tests <6>[ 0.151407] Running RCU Tasks Trace wait API self tests <6>[ 0.164463] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.164717] posixtimers hash table entries: 4096 (order: 7, 294912 bytes, linear) <6>[ 0.164791] futex hash table entries: 2048 (262144 bytes on 1 NUMA nodes, total 256 KiB, linear). <6>[ 0.165505] pinctrl core: initialized pinctrl subsystem <6>[ 0.166230] PM: RTC time: 02:43:32, date: 2025-11-18 <6>[ 0.167008] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.167984] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.168285] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.168569] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.168624] audit: initializing netlink subsys (disabled) <5>[ 0.168693] audit: type=2000 audit(1763433812.056:1): state=initialized audit_enabled=0 res=1 <6>[ 0.169756] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.169758] thermal_sys: Registered thermal governor 'bang_bang' <6>[ 0.169764] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.169769] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.169773] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.169814] cpuidle: using governor ladder <6>[ 0.169814] cpuidle: using governor menu <6>[ 0.169814] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 <6>[ 0.170621] PCI: ECAM [mem 0xc0000000-0xcfffffff] (base 0xc0000000) for domain 0000 [bus 00-ff] <6>[ 0.170648] PCI: Using configuration type 1 for base access <6>[ 0.170770] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. <6>[ 0.172482] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.172482] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.172482] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.172482] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.177266] raid6: skipped pq benchmark and selected avx2x4 <6>[ 0.177273] raid6: using avx2x2 recovery algorithm <6>[ 0.177872] fbcon: Taking over console <6>[ 0.178060] ACPI: Added _OSI(Module Device) <6>[ 0.178068] ACPI: Added _OSI(Processor Device) <6>[ 0.178077] ACPI: Added _OSI(Processor Aggregator Device) <6>[ 0.183432] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.693802] ACPI: 31 ACPI AML tables successfully acquired and loaded <6>[ 0.715390] ACPI: EC: EC started <6>[ 0.715406] ACPI: EC: interrupt blocked <6>[ 0.720143] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 0.720153] ACPI: EC: Boot ECDT EC used to handle transactions <6>[ 0.784505] Callback from call_rcu_tasks() invoked. <6>[ 1.000718] ACPI: USB4 _OSC: OS supports USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.000736] ACPI: USB4 _OSC: OS controls USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.063875] ACPI: Interpreter enabled <6>[ 1.064063] ACPI: PM: (supports S0 S4 S5) <6>[ 1.064072] ACPI: Using IOAPIC for interrupt routing <6>[ 1.071623] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug <6>[ 1.071636] PCI: Ignoring E820 reservations for host bridge windows <6>[ 1.102023] ACPI: Enabled 10 GPEs in block 00 to 7F <6>[ 1.102090] ACPI: Enabled 13 GPEs in block 80 to DF <6>[ 1.166201] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.BTRT: New power resource <6>[ 1.166999] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.DBTR: New power resource <6>[ 1.171976] ACPI: \_SB_.PC00.PAUD: New power resource <6>[ 1.505939] ACPI: \_SB_.PC00.CNVW.WRST: New power resource <6>[ 1.527664] ACPI: \_SB_.PC00.RP02.PXP_: New power resource <6>[ 1.681733] ACPI: \_SB_.PC00.RP03.PXSX.WRST: New power resource <6>[ 1.684617] ACPI: \_SB_.PC00.RP04.PXP_: New power resource <6>[ 1.697639] ACPI: \_SB_.PC00.RP05.PXP_: New power resource <6>[ 1.712583] ACPI: \_SB_.PC00.TBT0: New power resource <6>[ 1.713041] ACPI: \_SB_.PC00.TBT1: New power resource <6>[ 1.713476] ACPI: \_SB_.PC00.D3C_: New power resource <6>[ 1.944903] ACPI: \_TZ_.FN00: New power resource <6>[ 1.945452] ACPI: \_TZ_.FN01: New power resource <6>[ 1.945977] ACPI: \_TZ_.FN02: New power resource <6>[ 1.946500] ACPI: \_TZ_.FN03: New power resource <6>[ 1.947022] ACPI: \_TZ_.FN04: New power resource <6>[ 1.948847] ACPI: \PIN_: New power resource <6>[ 1.952139] ACPI: PCI Root Bridge [PC00] (domain 0000 [bus 00-fe]) <6>[ 1.952154] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3] <6>[ 1.956035] acpi PNP0A08:00: _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability LTR DPC] <6>[ 1.965484] PCI host bridge to bus 0000:00 <6>[ 1.965515] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] <6>[ 1.965522] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] <6>[ 1.965529] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] <6>[ 1.965536] pci_bus 0000:00: root bus resource [mem 0x80800000-0xbfffffff window] <6>[ 1.965544] pci_bus 0000:00: root bus resource [mem 0x2000000000-0x3fbfffffff window] <6>[ 1.965553] pci_bus 0000:00: root bus resource [bus 00-fe] <6>[ 1.968468] pci 0000:00:00.0: [8086:6400] type 00 class 0x060000 conventional PCI endpoint <6>[ 1.969112] pci 0000:00:02.0: [8086:64a0] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint <6>[ 1.969203] pci 0000:00:02.0: BAR 0 [mem 0x3814000000-0x3814ffffff 64bit pref] <6>[ 1.969211] pci 0000:00:02.0: BAR 2 [mem 0x2000000000-0x200fffffff 64bit pref] <6>[ 1.969221] pci 0000:00:02.0: ROM [mem 0xffe00000-0xffffffff pref] <6>[ 1.969264] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] <6>[ 1.970563] pci 0000:00:04.0: [8086:641d] type 00 class 0x118000 conventional PCI endpoint <6>[ 1.970592] pci 0000:00:04.0: BAR 0 [mem 0x3815300000-0x381531ffff 64bit] <6>[ 1.972358] pci 0000:00:05.0: [8086:645d] type 00 class 0x048000 PCIe Root Complex Integrated Endpoint <6>[ 1.972388] pci 0000:00:05.0: BAR 0 [mem 0x3812000000-0x3813ffffff 64bit] <6>[ 1.972395] pci 0000:00:05.0: BAR 4 [mem 0x3815373000-0x3815373fff 64bit] <6>[ 1.973282] pci 0000:00:07.0: [8086:a84e] type 01 class 0x060400 PCIe Root Port <6>[ 1.973324] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 1.973336] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 1.973355] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 1.973471] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold <6>[ 1.973545] pci 0000:00:07.0: PTM enabled (root), 4ns granularity <6>[ 1.977632] pci 0000:00:07.1: [8086:a84f] type 01 class 0x060400 PCIe Root Port <6>[ 1.977681] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 1.977693] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 1.977712] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 1.977828] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold <6>[ 1.977894] pci 0000:00:07.1: PTM enabled (root), 4ns granularity <6>[ 1.982569] pci 0000:00:07.2: [8086:a860] type 01 class 0x060400 PCIe Root Port <6>[ 1.982616] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 1.982628] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 1.982646] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 1.982763] pci 0000:00:07.2: PME# supported from D0 D3hot D3cold <6>[ 1.982828] pci 0000:00:07.2: PTM enabled (root), 4ns granularity <6>[ 1.986823] pci 0000:00:0a.0: [8086:647d] type 00 class 0x118000 PCIe Root Complex Integrated Endpoint <6>[ 1.986859] pci 0000:00:0a.0: BAR 0 [mem 0x3815350000-0x381535ffff 64bit] <6>[ 1.986873] pci 0000:00:0a.0: enabling Extended Tags <6>[ 1.987113] pci 0000:00:0b.0: [8086:643e] type 00 class 0x120000 PCIe Root Complex Integrated Endpoint <6>[ 1.987142] pci 0000:00:0b.0: BAR 0 [mem 0x3810000000-0x3811ffffff 64bit] <6>[ 1.987149] pci 0000:00:0b.0: BAR 4 [mem 0x3815372000-0x3815372fff 64bit] <6>[ 1.988041] pci 0000:00:0d.0: [8086:a831] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 1.988094] pci 0000:00:0d.0: BAR 0 [mem 0x3815340000-0x381534ffff 64bit] <6>[ 1.988166] pci 0000:00:0d.0: PME# supported from D3hot D3cold <6>[ 1.989769] pci 0000:00:0d.2: [8086:a833] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 1.989822] pci 0000:00:0d.2: BAR 0 [mem 0x38152c0000-0x38152fffff 64bit] <6>[ 1.989830] pci 0000:00:0d.2: BAR 2 [mem 0x3815371000-0x3815371fff 64bit] <6>[ 1.989888] pci 0000:00:0d.2: supports D1 D2 <6>[ 1.989891] pci 0000:00:0d.2: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 1.991170] pci 0000:00:0d.3: [8086:a834] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 1.991222] pci 0000:00:0d.3: BAR 0 [mem 0x3815280000-0x38152bffff 64bit] <6>[ 1.991230] pci 0000:00:0d.3: BAR 2 [mem 0x3815370000-0x3815370fff 64bit] <6>[ 1.991288] pci 0000:00:0d.3: supports D1 D2 <6>[ 1.991292] pci 0000:00:0d.3: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 1.992604] pci 0000:00:12.0: [8086:a845] type 00 class 0x070000 conventional PCI endpoint <6>[ 1.992662] pci 0000:00:12.0: BAR 0 [mem 0x3815330000-0x381533ffff 64bit] <6>[ 1.992732] pci 0000:00:12.0: PME# supported from D0 D3hot <6>[ 1.995254] pci 0000:00:13.0: [8086:a862] type 00 class 0x078000 conventional PCI endpoint <6>[ 1.995350] pci 0000:00:13.0: BAR 0 [mem 0x381536f000-0x381536ffff 64bit] <6>[ 1.995494] pci 0000:00:13.0: PME# supported from D3hot <6>[ 1.995970] pci 0000:00:14.0: [8086:a87d] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 1.996023] pci 0000:00:14.0: BAR 0 [mem 0x3815320000-0x381532ffff 64bit] <6>[ 1.996091] pci 0000:00:14.0: PME# supported from D3hot D3cold <6>[ 1.998637] pci 0000:00:14.2: [8086:a87f] type 00 class 0x050000 conventional PCI endpoint <6>[ 1.998701] pci 0000:00:14.2: BAR 0 [mem 0x3815360000-0x3815367fff 64bit] <6>[ 1.998710] pci 0000:00:14.2: BAR 2 [mem 0x381536e000-0x381536efff 64bit] <6>[ 1.999045] pci 0000:00:15.0: [8086:a878] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 1.999152] pci 0000:00:15.0: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.014052] pci 0000:00:15.1: [8086:a879] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.014123] pci 0000:00:15.1: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.025451] pci 0000:00:15.2: [8086:a87a] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.025524] pci 0000:00:15.2: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.038372] pci 0000:00:15.3: [8086:a87b] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.038536] pci 0000:00:15.3: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.051590] pci 0000:00:16.0: [8086:a870] type 00 class 0x078000 conventional PCI endpoint <6>[ 2.051739] pci 0000:00:16.0: BAR 0 [mem 0x3815369000-0x3815369fff 64bit] <6>[ 2.051900] pci 0000:00:16.0: PME# supported from D3hot <6>[ 2.056616] pci 0000:00:1c.0: [8086:a839] type 01 class 0x060400 PCIe Root Port <6>[ 2.056662] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.056674] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 2.056685] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 2.056838] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold <6>[ 2.056929] pci 0000:00:1c.0: PTM enabled (root), 4ns granularity <6>[ 2.061883] pci 0000:00:1c.4: [8086:a83c] type 01 class 0x060400 PCIe Root Port <6>[ 2.061988] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.062019] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 2.062360] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold <6>[ 2.062564] pci 0000:00:1c.4: PTM enabled (root), 4ns granularity <6>[ 2.067338] pci 0000:00:1f.0: [8086:a807] type 00 class 0x060100 conventional PCI endpoint <6>[ 2.068845] pci 0000:00:1f.3: [8086:a828] type 00 class 0x040100 conventional PCI endpoint <6>[ 2.068959] pci 0000:00:1f.3: BAR 0 [mem 0x3815200000-0x381527ffff 64bit] <6>[ 2.068974] pci 0000:00:1f.3: BAR 4 [mem 0x3815000000-0x38151fffff 64bit] <6>[ 2.069088] pci 0000:00:1f.3: PME# supported from D3hot D3cold <6>[ 2.069600] pci 0000:00:1f.4: [8086:a822] type 00 class 0x0c0500 conventional PCI endpoint <6>[ 2.069668] pci 0000:00:1f.4: BAR 0 [mem 0x3815368000-0x38153680ff 64bit] <6>[ 2.069680] pci 0000:00:1f.4: BAR 4 [io 0xefa0-0xefbf] <6>[ 2.070876] pci 0000:00:1f.5: [8086:a823] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.071057] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff] <6>[ 2.072013] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 2.072188] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 2.072357] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 2.072552] pci 0000:7f:00.0: [10ec:8161] type 00 class 0x020000 PCIe Endpoint <6>[ 2.072624] pci 0000:7f:00.0: BAR 0 [io 0x3000-0x30ff] <6>[ 2.072635] pci 0000:7f:00.0: BAR 2 [mem 0x94304000-0x94304fff 64bit] <6>[ 2.072644] pci 0000:7f:00.0: BAR 4 [mem 0x94300000-0x94303fff 64bit] <6>[ 2.072809] pci 0000:7f:00.0: supports D1 D2 <6>[ 2.072813] pci 0000:7f:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.073430] pci 0000:00:1c.0: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.075653] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.076085] pci 0000:80:00.0: [15b7:5011] type 00 class 0x010802 PCIe Endpoint <6>[ 2.076143] pci 0000:80:00.0: BAR 0 [mem 0x94200000-0x94203fff 64bit] <6>[ 2.077335] pci 0000:00:1c.4: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.077399] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.498818] ACPI: \_SB_.PEPD: Duplicate LPS0 _DSM functions (mask: 0x1) <6>[ 12.448642] Low-power S0 idle used by default for system suspend <6>[ 12.501495] ACPI: EC: interrupt unblocked <6>[ 12.501506] ACPI: EC: event unblocked <6>[ 12.501539] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 12.501546] ACPI: EC: GPE=0x6e <6>[ 12.501794] ACPI: \_SB_.PC00.LPCB.H_EC: Boot ECDT EC initialization complete <6>[ 12.501803] ACPI: \_SB_.PC00.LPCB.H_EC: EC: Used to handle transactions and events <6>[ 12.502803] iommu: Default domain type: Translated <6>[ 12.502803] iommu: DMA domain TLB invalidation policy: lazy mode <5>[ 12.506650] SCSI subsystem initialized <7>[ 12.506734] libata version 3.00 loaded. <6>[ 12.506809] ACPI: bus type USB registered <6>[ 12.507579] usbcore: registered new interface driver usbfs <6>[ 12.507718] usbcore: registered new interface driver hub <6>[ 12.507822] usbcore: registered new device driver usb <6>[ 12.508144] pps_core: LinuxPPS API ver. 1 registered <6>[ 12.508155] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 12.508203] PTP clock support registered <6>[ 12.508483] EDAC MC: Ver: 3.0.0 <6>[ 12.510543] efivars: Registered efivars operations <6>[ 12.513953] NetLabel: Initializing <6>[ 12.513963] NetLabel: domain hash size = 128 <6>[ 12.513973] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO <6>[ 12.514127] NetLabel: unlabeled traffic allowed by default <6>[ 12.514166] mctp: management component transport protocol core <6>[ 12.514178] NET: Registered PF_MCTP protocol family <6>[ 12.514283] PCI: Using ACPI for IRQ routing <7>[ 12.543772] PCI: pci_cache_line_size set to 64 bytes <6>[ 12.544065] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]: can't claim; no compatible bridge window <7>[ 12.544228] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] <7>[ 12.544261] e820: reserve RAM buffer [mem 0x68ff8000-0x6bffffff] <7>[ 12.544269] e820: reserve RAM buffer [mem 0x6992d000-0x6bffffff] <7>[ 12.544276] e820: reserve RAM buffer [mem 0x6cac1000-0x6fffffff] <7>[ 12.544282] e820: reserve RAM buffer [mem 0x87f800000-0x87fffffff] <6>[ 12.545597] pci 0000:00:02.0: vgaarb: setting as boot VGA device <6>[ 12.545597] pci 0000:00:02.0: vgaarb: bridge control possible <6>[ 12.545597] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none <6>[ 12.545601] vgaarb: loaded <7>[ 12.549435] Monitor-Mwait will be used to enter C-1 state <7>[ 12.549551] Monitor-Mwait will be used to enter C-2 state <7>[ 12.549551] Monitor-Mwait will be used to enter C-3 state <6>[ 12.558404] clocksource: Switched to clocksource tsc-early <5>[ 12.569735] VFS: Disk quotas dquot_6.6.0 <6>[ 12.569802] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 12.572262] AppArmor: AppArmor Filesystem Enabled <6>[ 12.572677] pnp: PnP ACPI init <6>[ 12.574382] system 00:00: [io 0x0680-0x069f] has been reserved <6>[ 12.574403] system 00:00: [io 0x164e-0x164f] has been reserved <6>[ 12.576450] system 00:02: [io 0x06a4] has been reserved <6>[ 12.576464] system 00:02: [io 0x06a0] has been reserved <6>[ 12.606531] system 00:03: [mem 0xfedc0000-0xfedc7fff] has been reserved <6>[ 12.606554] system 00:03: [mem 0xd8000000-0xd8000fff] has been reserved <6>[ 12.606573] system 00:03: [mem 0x00000000-0x00000fff] could not be reserved <6>[ 12.606587] system 00:03: [mem 0xc0000000-0xcfffffff] has been reserved <6>[ 12.606601] system 00:03: [mem 0xfed20000-0xfed7ffff] has been reserved <6>[ 12.606616] system 00:03: [mem 0xfc800000-0xfc81ffff] could not be reserved <6>[ 12.606631] system 00:03: [mem 0xfed45000-0xfed8ffff] could not be reserved <6>[ 12.606644] system 00:03: [mem 0xfee00000-0xfeefffff] has been reserved <6>[ 12.612031] system 00:04: [io 0x2000-0x20fe] has been reserved <6>[ 12.616766] system 00:06: [io 0x1854-0x1857] has been reserved <6>[ 12.617051] system 00:07: [mem 0x00000000-0x0009cfff] could not be reserved <6>[ 12.624886] pnp: PnP ACPI: found 8 devices <6>[ 12.641220] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns <6>[ 12.641569] NET: Registered PF_INET protocol family <6>[ 12.641815] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 12.644779] tcp_listen_portaddr_hash hash table entries: 16384 (order: 9, 1179648 bytes, linear) <6>[ 12.645089] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 12.645296] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 12.646334] TCP bind hash table entries: 65536 (order: 12, 9437184 bytes, vmalloc hugepage) <6>[ 12.648357] TCP: Hash tables configured (established 262144 bind 65536) <6>[ 12.648933] UDP hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 12.650288] UDP-Lite hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 12.651684] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 12.651778] pci 0000:00:07.0: bridge window [io 0x1000-0x0fff] to [bus 01-2a] add_size 1000 <6>[ 12.651796] pci 0000:00:07.1: bridge window [io 0x1000-0x0fff] to [bus 2b-54] add_size 1000 <6>[ 12.651810] pci 0000:00:07.2: bridge window [io 0x1000-0x0fff] to [bus 55-7e] add_size 1000 <6>[ 12.651877] pci 0000:00:07.0: bridge window [io 0x4000-0x4fff]: assigned <6>[ 12.651887] pci 0000:00:07.1: bridge window [io 0x5000-0x5fff]: assigned <6>[ 12.651896] pci 0000:00:07.2: bridge window [io 0x6000-0x6fff]: assigned <6>[ 12.651907] pci 0000:00:15.0: BAR 0 [mem 0x381536a000-0x381536afff 64bit]: assigned <6>[ 12.651938] pci 0000:00:15.1: BAR 0 [mem 0x381536b000-0x381536bfff 64bit]: assigned <6>[ 12.651964] pci 0000:00:15.2: BAR 0 [mem 0x381536c000-0x381536cfff 64bit]: assigned <6>[ 12.651989] pci 0000:00:15.3: BAR 0 [mem 0x381536d000-0x381536dfff 64bit]: assigned <6>[ 12.652015] pci 0000:00:1f.5: BAR 0 [mem 0x80800000-0x80800fff]: assigned <6>[ 12.652057] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 12.652071] pci 0000:00:07.0: bridge window [io 0x4000-0x4fff] <6>[ 12.652083] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 12.652095] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 12.652117] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 12.652126] pci 0000:00:07.1: bridge window [io 0x5000-0x5fff] <6>[ 12.652137] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 12.652149] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 12.652164] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 12.652173] pci 0000:00:07.2: bridge window [io 0x6000-0x6fff] <6>[ 12.652184] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 12.652196] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 12.652212] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 12.652220] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 12.652231] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 12.652246] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 12.652282] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 12.652331] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] <6>[ 12.652340] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] <6>[ 12.652348] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] <6>[ 12.652357] pci_bus 0000:00: resource 7 [mem 0x80800000-0xbfffffff window] <6>[ 12.652365] pci_bus 0000:00: resource 8 [mem 0x2000000000-0x3fbfffffff window] <6>[ 12.652375] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff] <6>[ 12.652383] pci_bus 0000:01: resource 1 [mem 0x8e000000-0x93ffffff] <6>[ 12.652391] pci_bus 0000:01: resource 2 [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 12.652401] pci_bus 0000:2b: resource 0 [io 0x5000-0x5fff] <6>[ 12.652408] pci_bus 0000:2b: resource 1 [mem 0x88000000-0x8dffffff] <6>[ 12.652416] pci_bus 0000:2b: resource 2 [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 12.652426] pci_bus 0000:55: resource 0 [io 0x6000-0x6fff] <6>[ 12.652434] pci_bus 0000:55: resource 1 [mem 0x82000000-0x87ffffff] <6>[ 12.652442] pci_bus 0000:55: resource 2 [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 12.652452] pci_bus 0000:7f: resource 0 [io 0x3000-0x3fff] <6>[ 12.652459] pci_bus 0000:7f: resource 1 [mem 0x94300000-0x943fffff] <6>[ 12.652468] pci_bus 0000:80: resource 1 [mem 0x94200000-0x942fffff] <6>[ 12.653820] pci 0000:00:0d.0: enabling device (0000 -> 0002) <6>[ 12.655928] PCI: CLS 0 bytes, default 64 <6>[ 12.656058] DMAR: No RMRR found <6>[ 12.656074] DMAR: No ATSR found <6>[ 12.656080] DMAR: dmar1: Using Queued invalidation <6>[ 12.656090] DMAR: dmar0: Using Queued invalidation <6>[ 12.656098] DMAR: dmar2: Using Queued invalidation <6>[ 12.657263] pci 0000:00:04.0: Adding to iommu group 0 <6>[ 12.657381] pci 0000:00:05.0: Adding to iommu group 1 <6>[ 12.657478] pci 0000:00:0a.0: Adding to iommu group 2 <6>[ 12.657562] pci 0000:00:0b.0: Adding to iommu group 3 <6>[ 12.662084] pci 0000:00:02.0: Adding to iommu group 4 <6>[ 12.664128] pci 0000:00:00.0: Adding to iommu group 5 <6>[ 12.664233] pci 0000:00:07.0: Adding to iommu group 6 <6>[ 12.664324] pci 0000:00:07.1: Adding to iommu group 7 <6>[ 12.664422] pci 0000:00:07.2: Adding to iommu group 8 <6>[ 12.664538] pci 0000:00:0d.0: Adding to iommu group 9 <6>[ 12.664605] pci 0000:00:0d.2: Adding to iommu group 9 <6>[ 12.664664] pci 0000:00:0d.3: Adding to iommu group 9 <6>[ 12.664759] pci 0000:00:12.0: Adding to iommu group 10 <6>[ 12.664869] pci 0000:00:13.0: Adding to iommu group 11 <6>[ 12.664974] pci 0000:00:14.0: Adding to iommu group 12 <6>[ 12.665034] pci 0000:00:14.2: Adding to iommu group 12 <6>[ 12.665158] pci 0000:00:15.0: Adding to iommu group 13 <6>[ 12.665219] pci 0000:00:15.1: Adding to iommu group 13 <6>[ 12.665291] pci 0000:00:15.2: Adding to iommu group 13 <6>[ 12.665357] pci 0000:00:15.3: Adding to iommu group 13 <6>[ 12.665451] pci 0000:00:16.0: Adding to iommu group 14 <6>[ 12.665538] pci 0000:00:1c.0: Adding to iommu group 15 <6>[ 12.665651] pci 0000:00:1c.4: Adding to iommu group 16 <6>[ 12.665780] pci 0000:00:1f.0: Adding to iommu group 17 <6>[ 12.665843] pci 0000:00:1f.3: Adding to iommu group 17 <6>[ 12.665911] pci 0000:00:1f.4: Adding to iommu group 17 <6>[ 12.665980] pci 0000:00:1f.5: Adding to iommu group 17 <6>[ 12.666066] pci 0000:7f:00.0: Adding to iommu group 18 <6>[ 12.666183] pci 0000:80:00.0: Adding to iommu group 19 <6>[ 12.678110] DMAR: Intel(R) Virtualization Technology for Directed I/O <6>[ 12.678130] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) <6>[ 12.678139] software IO TLB: mapped [mem 0x0000000063ac2000-0x0000000067ac2000] (64MB) <6>[ 12.684339] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 12.684721] clocksource: Switched to clocksource tsc <6>[ 12.684985] platform rtc_cmos: registered platform RTC device (no PNP device found) <5>[ 12.695398] Initialise system trusted keyrings <5>[ 12.695516] Key type blacklist registered <6>[ 12.696151] workingset: timestamp_bits=36 max_order=23 bucket_order=0 <6>[ 12.711562] squashfs: version 4.0 (2009/01/31) Phillip Lougher <6>[ 12.711691] ntfs3: Enabled Linux POSIX ACLs support <6>[ 12.711698] ntfs3: Read-only LZX/Xpress compression included <5>[ 12.712382] integrity: Platform Keyring initialized <5>[ 12.712407] integrity: Machine keyring initialized <6>[ 12.719728] xor: automatically using best checksumming function avx <5>[ 12.719741] Key type asymmetric registered <5>[ 12.719756] Asymmetric key parser 'x509' registered <6>[ 12.719907] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) <6>[ 12.720587] io scheduler mq-deadline registered <6>[ 12.722123] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 12.724011] pcieport 0000:00:07.0: PME: Signaling with IRQ 126 <6>[ 12.724572] pcieport 0000:00:07.0: AER: enabled with IRQ 126 <6>[ 12.725877] pcieport 0000:00:07.1: PME: Signaling with IRQ 127 <6>[ 12.726379] pcieport 0000:00:07.1: AER: enabled with IRQ 127 <6>[ 12.727630] pcieport 0000:00:07.2: PME: Signaling with IRQ 128 <6>[ 12.728146] pcieport 0000:00:07.2: AER: enabled with IRQ 128 <6>[ 12.729295] pcieport 0000:00:1c.0: PME: Signaling with IRQ 129 <6>[ 12.729801] pcieport 0000:00:1c.0: AER: enabled with IRQ 129 <6>[ 12.735541] pcieport 0000:00:1c.4: PME: Signaling with IRQ 130 <6>[ 12.736130] pcieport 0000:00:1c.4: AER: enabled with IRQ 130 <6>[ 12.738299] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:16/PNP0C09:00/PNP0C0D:00/input/input0 <6>[ 12.738547] ACPI: button: Lid Switch [LID0] <6>[ 12.738863] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1 <6>[ 12.739090] ACPI: button: Sleep Button [SLPB] <6>[ 12.739358] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 <6>[ 12.739829] ACPI: button: Power Button [PWRB] <6>[ 12.904504] thermal LNXTHERM:00: registered as thermal_zone0 <6>[ 12.904524] ACPI: thermal: Thermal Zone [TZ00] (63 C) <6>[ 12.906228] ACPI: battery: Slot [BAT1] (battery absent) <6>[ 12.906425] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled <6>[ 12.907493] ACPI: battery: Slot [BAT0] (battery present) <6>[ 12.929729] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A <6>[ 12.946442] serial 0000:00:12.0: enabling device (0000 -> 0002) <5>[ 12.949964] hpet_acpi_add: no address or irqs in _CRS <6>[ 12.950219] Linux agpgart interface v0.103 <6>[ 12.951230] ACPI: bus type drm_connector registered <7>[ 12.952275] initcall simpledrm_platform_driver_init blacklisted <6>[ 12.976099] loop: module loaded <6>[ 13.031284] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002) <6>[ 13.148135] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002) <6>[ 13.261224] intel-lpss 0000:00:15.2: enabling device (0000 -> 0002) <6>[ 13.373646] intel-lpss 0000:00:15.3: enabling device (0000 -> 0002) <5>[ 13.487251] Key type psk registered <6>[ 13.490881] nvme 0000:80:00.0: platform quirk: setting simple suspend <6>[ 13.491583] nvme nvme0: pci function 0000:80:00.0 <6>[ 13.492985] tun: Universal TUN/TAP device driver, 1.6 <6>[ 13.494032] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 13.494168] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 <6>[ 13.497825] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 13.499960] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 13.499995] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 <6>[ 13.500021] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 13.500427] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 13.500448] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.500459] usb usb1: Product: xHCI Host Controller <6>[ 13.500466] usb usb1: Manufacturer: Linux 6.18.0-rc6-lgci-xe-xe-4121-91fc6d984707c9bfd+ xhci-hcd <6>[ 13.500478] usb usb1: SerialNumber: 0000:00:0d.0 <6>[ 13.501505] hub 1-0:1.0: USB hub found <6>[ 13.501587] hub 1-0:1.0: 1 port detected <6>[ 13.505421] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 13.505436] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.505447] usb usb2: Product: xHCI Host Controller <6>[ 13.505454] usb usb2: Manufacturer: Linux 6.18.0-rc6-lgci-xe-xe-4121-91fc6d984707c9bfd+ xhci-hcd <6>[ 13.505466] usb usb2: SerialNumber: 0000:00:0d.0 <6>[ 13.506254] hub 2-0:1.0: USB hub found <6>[ 13.506302] hub 2-0:1.0: 3 ports detected <6>[ 13.527085] nvme nvme0: 8/0/0 default/read/poll queues <6>[ 13.530968] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 13.531006] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 <6>[ 13.532779] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 13.534586] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 13.534611] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 <6>[ 13.534629] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 13.534910] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 13.534923] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.534934] usb usb3: Product: xHCI Host Controller <6>[ 13.534941] usb usb3: Manufacturer: Linux 6.18.0-rc6-lgci-xe-xe-4121-91fc6d984707c9bfd+ xhci-hcd <6>[ 13.534953] usb usb3: SerialNumber: 0000:00:14.0 <6>[ 13.535172] nvme0n1: p1 p2 <6>[ 13.536246] hub 3-0:1.0: USB hub found <6>[ 13.536299] hub 3-0:1.0: 8 ports detected <6>[ 13.565090] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 13.565110] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.565122] usb usb4: Product: xHCI Host Controller <6>[ 13.565129] usb usb4: Manufacturer: Linux 6.18.0-rc6-lgci-xe-xe-4121-91fc6d984707c9bfd+ xhci-hcd <6>[ 13.565141] usb usb4: SerialNumber: 0000:00:14.0 <6>[ 13.565893] hub 4-0:1.0: USB hub found <6>[ 13.565938] hub 4-0:1.0: 2 ports detected <6>[ 13.572963] usbcore: registered new interface driver usb-storage <6>[ 13.573151] usbcore: registered new interface driver usbserial_generic <6>[ 13.573249] usbserial: USB Serial support registered for generic <6>[ 13.573329] usbcore: registered new interface driver ftdi_sio <6>[ 13.573367] usbserial: USB Serial support registered for FTDI USB Serial Device <6>[ 13.573437] usbcore: registered new interface driver pl2303 <6>[ 13.573474] usbserial: USB Serial support registered for pl2303 <6>[ 13.573607] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 <4>[ 13.573617] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp <3>[ 14.285625] i8042: Can't read CTR while initializing i8042 <3>[ 14.285635] i8042 i8042: probe with driver i8042 failed with error -5 <6>[ 14.286149] mousedev: PS/2 mouse device common for all mice <6>[ 14.287210] rtc_cmos rtc_cmos: RTC can wake from S4 <6>[ 14.289061] rtc_cmos rtc_cmos: registered as rtc0 <6>[ 14.289301] rtc_cmos rtc_cmos: setting system clock to 2025-11-18T02:43:46 UTC (1763433826) <6>[ 14.289548] rtc_cmos rtc_cmos: alarms up to one month, y3k, 114 bytes nvram <6>[ 14.289618] i2c_dev: i2c /dev entries driver <6>[ 14.295742] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=5 (nowayout=0) <6>[ 14.295757] softdog: soft_reboot_cmd= soft_active_on_boot=0 <4>[ 14.295768] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. <6>[ 14.295810] device-mapper: uevent: version 1.0.3 <6>[ 14.296184] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev <6>[ 14.296202] intel_pstate: Intel P-state driver initializing <6>[ 14.300043] Hybrid CPU capacity scaling enabled <6>[ 14.300391] processor cpu0: EM: created perf domain <6>[ 14.300654] processor cpu1: EM: created perf domain <6>[ 14.300912] processor cpu2: EM: created perf domain <6>[ 14.301201] processor cpu3: EM: created perf domain <6>[ 14.304958] processor cpu4: EM: created perf domain <6>[ 14.305119] processor cpu5: EM: created perf domain <6>[ 14.305281] processor cpu6: EM: created perf domain <6>[ 14.305434] processor cpu7: EM: created perf domain <6>[ 14.306711] intel_pstate: HWP enabled <6>[ 14.306720] sdhci: Secure Digital Host Controller Interface driver <6>[ 14.306725] sdhci: Copyright(c) Pierre Ossman <6>[ 14.307510] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 14.313040] Relocating firmware framebuffer to offset 0x0000000000800000[d] within [mem 0x2000000000-0x200fffffff flags 0x14220c] <6>[ 14.313876] drop_monitor: Initializing network drop monitor service <6>[ 14.314079] NET: Registered PF_INET6 protocol family <6>[ 14.315692] Segment Routing with IPv6 <6>[ 14.315740] In-situ OAM (IOAM) with IPv6 <6>[ 14.315801] NET: Registered PF_PACKET protocol family <5>[ 14.316030] Key type dns_resolver registered <4>[ 14.322593] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' <6>[ 14.323372] microcode: Current revision: 0x00000124 <6>[ 14.324268] IPI shorthand broadcast: enabled <6>[ 14.337480] sched_clock: Marking stable (14327000595, 9844892)->(14434147228, -97301741) <6>[ 14.338337] registered taskstats version 1 <5>[ 14.340800] Loading compiled-in X.509 certificates <6>[ 14.384717] Demotion targets for Node 0: null <6>[ 14.384960] kmemleak: Kernel memory leak detector initialized (mem pool available: 14946) <6>[ 14.384964] kmemleak: Automatic memory scanning thread started <5>[ 14.385191] Key type .fscrypt registered <5>[ 14.385196] Key type fscrypt-provisioning registered <6>[ 14.388135] Btrfs loaded, zoned=yes, fsverity=yes <5>[ 14.390656] Key type encrypted registered <6>[ 14.390662] AppArmor: AppArmor sha256 policy hashing enabled <6>[ 14.390864] ima: No TPM chip found, activating TPM-bypass! <5>[ 14.390877] Loading compiled-in module X.509 certificates <5>[ 14.391549] Loaded X.509 cert 'Build time autogenerated kernel key: 110d11f22e23ffd5f754968e95580a6d87155d85' <6>[ 14.391559] ima: Allocated hash algorithm: sha256 <6>[ 14.391599] ima: No architecture policies found <6>[ 14.391678] evm: Initialising EVM extended attributes: <6>[ 14.391682] evm: security.selinux <6>[ 14.391685] evm: security.SMACK64 <6>[ 14.391687] evm: security.SMACK64EXEC <6>[ 14.391690] evm: security.SMACK64TRANSMUTE <6>[ 14.391693] evm: security.SMACK64MMAP <6>[ 14.391696] evm: security.apparmor <6>[ 14.391699] evm: security.ima <6>[ 14.391702] evm: security.capability <6>[ 14.391704] evm: HMAC attrs: 0x1 <6>[ 14.393695] PM: Magic number: 1:278:713 <6>[ 14.393880] netconsole: network logging started <6>[ 14.394489] RAS: Correctable Errors collector initialized. <6>[ 14.394611] clk: Disabling unused clocks <6>[ 14.394620] PM: genpd: Disabling unused power domains <4>[ 14.395138] check access for rdinit=/init failed: -2, ignoring <6>[ 14.395146] md: Waiting for all devices to be available before autodetect <6>[ 14.395151] md: If you don't use raid, use raid=noautodetect <6>[ 14.395156] md: Autodetecting RAID arrays. <6>[ 14.395164] md: autorun ... <6>[ 14.395167] md: ... autorun DONE. <6>[ 14.437446] EXT4-fs (nvme0n1p2): mounted filesystem 9a25468b-c3fd-45e2-b59f-4eab10a53c55 ro with ordered data mode. Quota mode: none. <6>[ 14.437519] VFS: Mounted root (ext4 filesystem) readonly on device 259:2. <6>[ 14.438890] devtmpfs: mounted <6>[ 14.455682] Freeing unused decrypted memory: 2036K <6>[ 14.456644] Freeing unused kernel image (initmem) memory: 5704K <6>[ 14.456668] Write protecting the kernel read-only data: 36864k <6>[ 14.457414] Freeing unused kernel image (text/rodata gap) memory: 1200K <6>[ 14.457769] Freeing unused kernel image (rodata/data gap) memory: 700K <6>[ 14.462311] x86/mm: Checked W+X mappings: passed, no W+X pages found. <6>[ 14.462869] Run /sbin/init as init process <7>[ 14.462873] with arguments: <7>[ 14.462874] /sbin/init <7>[ 14.462875] with environment: <7>[ 14.462876] HOME=/ <7>[ 14.462876] TERM=linux <7>[ 14.509163] systemd[1]: Inserted module 'autofs4' <7>[ 14.532539] systemd[1]: systemd 255.4-1ubuntu8.5 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <7>[ 14.532568] systemd[1]: Detected architecture x86-64. <7>[ 14.534006] systemd[1]: Hostname set to . <7>[ 14.780293] systemd[1]: Queued start job for default target graphical.target. <7>[ 14.804652] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. <7>[ 14.806344] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck. <7>[ 14.807770] systemd[1]: Created slice user.slice - User and Session Slice. <7>[ 14.808031] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. <7>[ 14.808658] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point. <7>[ 14.808768] systemd[1]: Expecting device dev-disk-by\x2duuid-BBA9\x2dCAA8.device - /dev/disk/by-uuid/BBA9-CAA8... <7>[ 14.808858] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. <7>[ 14.808948] systemd[1]: Reached target slices.target - Slice Units. <7>[ 14.809019] systemd[1]: Reached target snapd.mounts-pre.target - Mounting snaps. <7>[ 14.809080] systemd[1]: Reached target snapd.mounts.target - Mounted snaps. <7>[ 14.809146] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. <7>[ 14.809369] systemd[1]: Listening on dm-event.socket - Device-mapper event daemon FIFOs. <7>[ 14.809732] systemd[1]: Listening on lvm2-lvmpolld.socket - LVM2 poll daemon socket. <7>[ 14.810005] systemd[1]: Listening on multipathd.socket - multipathd control socket. <7>[ 14.810302] systemd[1]: Listening on syslog.socket - Syslog Socket. <7>[ 14.810545] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket. <7>[ 14.810750] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. <7>[ 14.811227] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). <7>[ 14.811568] systemd[1]: Listening on systemd-journald.socket - Journal Socket. <7>[ 14.811839] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. <7>[ 14.812022] systemd[1]: systemd-pcrextend.socket - TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 14.812299] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. <7>[ 14.812557] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. <7>[ 14.831411] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... <7>[ 14.835347] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... <7>[ 14.838209] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... <7>[ 14.840782] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System... <7>[ 14.847658] systemd[1]: Starting systemd-journald.service - Journal Service... <7>[ 14.850614] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout... <7>[ 14.854106] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... <7>[ 14.857353] systemd[1]: Starting lvm2-monitor.service - Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... <7>[ 14.859858] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... <7>[ 14.863752] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... <7>[ 14.867083] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... <7>[ 14.872464] systemd-journald[206]: Collecting audit messages is disabled. <7>[ 14.873271] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... <7>[ 14.877236] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... <7>[ 14.880134] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... <7>[ 14.883472] systemd[1]: Starting modprobe@nvme_fabrics.service - Load Kernel Module nvme_fabrics... <7>[ 14.883779] systemd[1]: netplan-ovs-cleanup.service - OpenVSwitch configuration for cleanup was skipped because of an unmet condition check (ConditionFileIsExecutable=/usr/bin/ovs-vsctl). <7>[ 14.889223] systemd[1]: Starting systemd-fsck-root.service - File System Check on Root Device... <6>[ 14.893639] pstore: Using crash dump compression: deflate <7>[ 14.896688] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... <7>[ 14.896794] systemd[1]: systemd-pcrmachine.service - TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 14.896869] systemd[1]: systemd-tpm2-setup-early.service - TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <6>[ 14.897428] pstore: Registered efi_pstore as persistent store backend <6>[ 14.901686] fuse: init (API version 7.45) <7>[ 14.901922] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... <7>[ 14.908028] systemd[1]: Started systemd-journald.service - Journal Service. <6>[ 15.049197] EXT4-fs (nvme0n1p2): re-mounted 9a25468b-c3fd-45e2-b59f-4eab10a53c55 r/w. <6>[ 15.076987] Adding 8388604k swap on /swap.img. Priority:-2 extents:66 across:274595840k SS <7>[ 15.090558] systemd-journald[206]: Received client request to flush runtime journal. <7>[ 15.112234] systemd-journald[206]: /var/log/journal/2b6a2c75c75941a29794878cc3195815/system.journal: Journal file uses a different sequence number ID, rotating. <7>[ 15.112246] systemd-journald[206]: Rotating system journal. <4>[ 15.832063] nvme nvme0: using unchecked data buffer <6>[ 15.928060] intel_vsec 0000:00:0a.0: enabling device (0000 -> 0002) <6>[ 15.956892] intel_pmc_ssram_telemetry 0000:00:14.2: enabling device (0000 -> 0002) <6>[ 16.036810] input: Intel HID events as /devices/platform/INTC107B:00/input/input3 <6>[ 16.048354] intel-hid INTC107B:00: platform supports 5 button array <6>[ 16.060403] input: Intel HID 5 button array as /devices/platform/INTC107B:00/input/input4 <3>[ 16.092592] int3472-tps68470 i2c-INT3472:06: TPS68470 init error -121 <3>[ 16.092788] int3472-tps68470 i2c-INT3472:06: probe with driver int3472-tps68470 failed with error -121 <5>[ 16.172339] audit: type=1400 audit(1763433828.381:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="Discord" pid=421 comm="apparmor_parser" <5>[ 16.173224] audit: type=1400 audit(1763433828.382:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="1password" pid=420 comm="apparmor_parser" <5>[ 16.184898] audit: type=1400 audit(1763433828.393:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="balena-etcher" pid=425 comm="apparmor_parser" <5>[ 16.186182] audit: type=1400 audit(1763433828.395:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name=4D6F6E676F444220436F6D70617373 pid=422 comm="apparmor_parser" <5>[ 16.193049] audit: type=1400 audit(1763433828.402:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="brave" pid=426 comm="apparmor_parser" <5>[ 16.193301] audit: type=1400 audit(1763433828.402:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="QtWebEngineProcess" pid=423 comm="apparmor_parser" <5>[ 16.193812] audit: type=1400 audit(1763433828.402:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chrome" pid=433 comm="apparmor_parser" <5>[ 16.194072] audit: type=1400 audit(1763433828.403:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ch-checkns" pid=431 comm="apparmor_parser" <5>[ 16.194430] audit: type=1400 audit(1763433828.403:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="busybox" pid=429 comm="apparmor_parser" <5>[ 16.194762] audit: type=1400 audit(1763433828.403:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ch-run" pid=432 comm="apparmor_parser" <6>[ 16.477619] pci 0000:00:05.0: Setting to D3hot <6>[ 16.489399] pci 0000:00:0b.0: Setting to D3hot <6>[ 16.501443] intel_pmc_core INT33A1:00: initialized <6>[ 16.530862] ACPI: bus type thunderbolt registered <6>[ 16.558004] intel_vpu 0000:00:0b.0: enabling device (0000 -> 0002) <6>[ 16.577325] intel_vpu 0000:00:0b.0: [drm] Firmware: intel/vpu/vpu_40xx_v0.0.bin, version: Jun 11 2024*LNL*ci_tag_ud202424_vpu_rc_20240611_0003*f3e8a8f27471d4127d8d92a8dc679b861ef43e43 <6>[ 16.577338] intel_vpu 0000:00:0b.0: [drm] Scheduler mode: OS <6>[ 16.615461] idma64 idma64.0: Found Intel integrated DMA 64-bit <6>[ 16.640666] idma64 idma64.1: Found Intel integrated DMA 64-bit <6>[ 16.642279] [drm] Initialized intel_vpu 1.0.0 for 0000:00:0b.0 on minor 0 <6>[ 16.665562] idma64 idma64.2: Found Intel integrated DMA 64-bit <6>[ 16.666787] r8169 0000:7f:00.0: enabling device (0000 -> 0003) <6>[ 16.682420] idma64 idma64.3: Found Intel integrated DMA 64-bit <6>[ 16.713416] proc_thermal_pci 0000:00:04.0: enabling device (0400 -> 0402) <6>[ 16.718473] intel_rapl_common: Found RAPL domain package <6>[ 16.718482] intel_rapl_common: Found RAPL domain dram <6>[ 16.775089] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer <6>[ 16.775094] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules <6>[ 16.775095] RAPL PMU: hw unit of domain package 2^-14 Joules <6>[ 16.775096] RAPL PMU: hw unit of domain dram 2^-14 Joules <6>[ 16.775097] RAPL PMU: hw unit of domain psys 2^-14 Joules <6>[ 16.788281] r8169 0000:7f:00.0 eth0: RTL8168h/8111h, e4:fa:c4:a4:ee:2f, XID 541, IRQ 175 <6>[ 16.788288] r8169 0000:7f:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 16.795855] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6>[ 16.796484] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 16.856866] proc_thermal_pci 0000:00:04.0: msi enabled:1 msix enabled:0 <6>[ 16.860518] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 17.011473] block nvme0n1: No UUID available providing old NGUID <6>[ 17.100149] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.109062] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.168908] /proc/cgroups lists only v1 controllers, use cgroup.controllers of root cgroup for v2 info <6>[ 17.260948] intel_rapl_common: Found RAPL domain package <6>[ 17.260954] intel_rapl_common: Found RAPL domain core <6>[ 17.260957] intel_rapl_common: Found RAPL domain dram <6>[ 17.260959] intel_rapl_common: Found RAPL domain psys <6>[ 17.278091] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.303652] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.317074] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.323697] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.329164] intel_ish_ipc 0000:00:12.0: ISH loader: load firmware: intel/ish/ish_lnlm.bin <6>[ 17.355200] intel_ish_ipc 0000:00:12.0: ISH loader: firmware loaded. size:997888 <6>[ 17.355209] intel_ish_ipc 0000:00:12.0: ISH loader: FW base version: 5.8.0.7716 <6>[ 17.355211] intel_ish_ipc 0000:00:12.0: ISH loader: FW project version: 5.8.0.12472 <6>[ 17.408687] r8169 0000:7f:00.0 enp127s0: renamed from eth0 <4>[ 17.419267] spi-nor spi0.0: supply vcc not found, using dummy regulator <5>[ 17.460439] Creating 1 MTD partitions on "0000:00:1f.5": <5>[ 17.460467] 0x000000000000-0x000002000000 : "BIOS" <6>[ 17.465193] loop0: detected capacity change from 0 to 8 <6>[ 17.483384] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.525960] Generic FE-GE Realtek PHY r8169-0-7f00:00: attached PHY driver (mii_bus:phy_addr=r8169-0-7f00:00, irq=MAC) <6>[ 17.683278] r8169 0000:7f:00.0 enp127s0: Link is Down <6>[ 17.876632] Consider using thermal netlink events interface <6>[ 18.115943] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.358570] hid: raw HID events driver (C) Jiri Kosina <6>[ 18.365214] ish-hid {33AECD58-B679-4E54-9BD9-A04D34F0C226}: [hid-ish]: enum_devices_done OK, num_hid_devices=6 <6>[ 18.399335] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.404331] hid-generic 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.405395] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.406641] hid-generic 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.407806] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.409362] hid-generic 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.410578] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.410649] hid-generic 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.413198] hid-generic 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.414041] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.414300] hid-generic 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.417252] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.419990] hid-sensor-hub 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.422135] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.423069] hid-sensor-hub 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.425499] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.426620] hid-sensor-hub 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.428731] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.429293] hid-sensor-hub 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.430857] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.431779] hid-sensor-hub 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.433823] hid-sensor-hub 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.434641] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.436858] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.516360] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.520099] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.528189] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.532257] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.534197] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.540247] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.545191] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.549743] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.554564] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.557153] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.561340] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.566624] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.571254] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.576032] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.581290] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.587533] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.592513] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.596663] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.602752] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.609534] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.913025] typec port0: bound usb3-port1 (ops connector_ops) <6>[ 19.913066] typec port0: bound usb2-port1 (ops connector_ops) <6>[ 19.913118] typec port0: bound usb4_port1 (ops connector_ops [thunderbolt]) <6>[ 20.951182] typec port1: bound usb3-port2 (ops connector_ops) <6>[ 20.951226] typec port1: bound usb2-port2 (ops connector_ops) <6>[ 20.951262] typec port1: bound usb4_port3 (ops connector_ops [thunderbolt]) <6>[ 21.274537] r8169 0000:7f:00.0 enp127s0: Link is Up - 1Gbps/Full - flow control off <6>[ 28.758438] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 28.762383] pci 0000:00:1f.3: deferred probe pending: snd_hda_intel: couldn't bind with audio component <7>[ 34.617668] systemd-journald[206]: /var/log/journal/2b6a2c75c75941a29794878cc3195815/user-1000.journal: Journal file uses a different sequence number ID, rotating. <7>[ 53.182763] [IGT] xe_module_load: executing <4>[ 53.182808] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030 <7>[ 53.190835] [IGT] xe_module_load: starting subtest load <5>[ 53.438825] Setting dangerous option force_probe - tainting kernel <6>[ 53.441655] xe 0000:00:02.0: vgaarb: deactivate vga console <6>[ 53.443413] xe 0000:00:02.0: [drm] Found lunarlake (device ID 64a0) integrated display version 20.00 stepping B0 <7>[ 53.443422] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] LUNARLAKE 64a0:0004 dgfx:0 gfx:Xe2_LPG (20.04) media:Xe2_LPM (20.00) display:yes dma_m_s:46 tc:1 gscfi:0 cscfi:0 <7>[ 53.443532] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] Stepping = (G:B0, M:B0, B:**) <7>[ 53.443629] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] SR-IOV support: no (mode: none) <7>[ 53.445525] xe 0000:00:02.0: [drm:xe_ttm_stolen_mgr_init [xe]] Initialized stolen memory support with 58720256 bytes <7>[ 53.445644] xe 0000:00:02.0: [drm:intel_pch_detect [xe]] PCH not involved in display, using fake PCH type 1027 for south display <7>[ 53.445747] xe 0000:00:02.0: [drm:intel_dmc_wl_init [xe]] Sanitized enable_dmc_wl value: 0 (disabled) <7>[ 53.445861] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] graphic opregion physical addr: 0x6ff04018 <7>[ 53.446007] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ACPI OpRegion version 3.2.0 <7>[ 53.446124] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Public ACPI methods supported <7>[ 53.446216] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE supported <7>[ 53.446298] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE extension supported <7>[ 53.446378] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Mailbox #2 for backlight present <7>[ 53.446464] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Found valid VBT in ACPI OpRegion (RVDA) <7>[ 53.446552] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM type: LPDDR5 <7>[ 53.446669] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM channels: 8 <7>[ 53.446772] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num QGV points 4 <7>[ 53.446875] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num PSF GV points 0 <7>[ 53.447006] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 0: DCLK=2400 tRP=48 tRDPRE=40 tRAS=104 tRCD=48 tRC=152 <7>[ 53.447143] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 1: DCLK=4800 tRP=88 tRDPRE=72 tRAS=208 tRCD=88 tRC=296 <7>[ 53.447255] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 2: DCLK=6400 tRP=120 tRDPRE=80 tRAS=272 tRCD=120 tRC=392 <7>[ 53.447359] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 3: DCLK=8534 tRP=160 tRDPRE=96 tRAS=360 tRCD=160 tRC=520 <7>[ 53.447458] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 0: num_planes=0 deratedbw=23530 peakbw: 38400 <7>[ 53.447556] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 1: num_planes=0 deratedbw=36260 peakbw: 76800 <7>[ 53.447652] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.447748] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.447845] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 0: num_planes=0 deratedbw=27998 peakbw: 38400 <7>[ 53.447978] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 53.448101] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.448209] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.448302] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 0: num_planes=0 deratedbw=30935 peakbw: 38400 <7>[ 53.448397] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 53.448493] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.448586] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.448676] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 0: num_planes=0 deratedbw=32647 peakbw: 38400 <7>[ 53.448763] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 53.448853] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.448957] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.449069] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 0: num_planes=0 deratedbw=33577 peakbw: 38400 <7>[ 53.449176] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 53.449262] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.449343] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.449425] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 0: num_planes=0 deratedbw=34061 peakbw: 38400 <7>[ 53.449506] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 53.449586] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 53.449666] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 53.449751] xe 0000:00:02.0: [drm:intel_display_device_info_runtime_init [xe]] rawclk rate: 38400 kHz <7>[ 53.450115] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Set default to SSC at 120000 kHz <7>[ 53.450225] xe 0000:00:02.0: [drm:intel_bios_init [xe]] VBT signature "$VBT LUNARLAKE ", BDB version 262 <7>[ 53.450326] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 1 (size 10, min size 7) <7>[ 53.450422] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 2 (size 405, min size 5) <7>[ 53.450511] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 9 (size 100, min size 100) <7>[ 53.450599] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 12 (size 19, min size 19) <7>[ 53.450686] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 27 (size 850, min size 848) <7>[ 53.450769] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 40 (size 34, min size 34) <7>[ 53.450851] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Generating LFP data table pointers <7>[ 53.450958] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 41 (size 148, min size 148) <7>[ 53.451076] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 42 (size 1382, min size 1366) <7>[ 53.451178] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 43 (size 305, min size 305) <7>[ 53.451258] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 44 (size 136, min size 136) <7>[ 53.451338] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 52 (size 822, min size 822) <7>[ 53.451416] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 56 (size 210, min size 210) <7>[ 53.451492] xe 0000:00:02.0: [drm:intel_bios_init [xe]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7>[ 53.451566] xe 0000:00:02.0: [drm:intel_bios_init [xe]] crt_ddc_bus_pin: 2 <7>[ 53.451643] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x1806 <7>[ 53.451722] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 53.451808] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 53.451922] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 53.452033] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Skipping SDVO device mapping <7>[ 53.452142] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7>[ 53.452235] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 53.452316] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 53.452398] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port F VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 53.452482] xe 0000:00:02.0: [drm:intel_power_domains_init [xe]] Allowed DC state mask 0a <7>[ 53.452592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 53.452734] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_1 <7>[ 53.452876] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 53.453253] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf <7>[ 53.453428] xe 0000:00:02.0: [drm:icl_display_core_init [xe]] Unknown memory configuration; disabling address buddy logic. <7>[ 53.453557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on <7>[ 53.453665] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 53.453782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 53.453941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2 <6>[ 53.454074] xe 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=io+mem <7>[ 53.454094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A <7>[ 53.454223] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B <7>[ 53.454323] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C <7>[ 53.454422] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D <7>[ 53.454622] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC <7>[ 53.455071] xe 0000:00:02.0: [drm:intel_dmc_init [xe]] Loading i915/xe2lpd_dmc.bin <7>[ 53.455511] xe 0000:00:02.0: [drm:intel_fbc_init [xe]] Sanitized enable_fbc value: 1 <7>[ 53.455638] xe 0000:00:02.0: [drm:skl_wm_init [xe]] SAGV supported: yes, original SAGV block time: 12 us <7>[ 53.455739] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM0 latency not provided <7>[ 53.455827] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM1 latency 100 (100.0 usec) <7>[ 53.455934] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM2 latency 100 (100.0 usec) <7>[ 53.456044] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM3 latency 100 (100.0 usec) <7>[ 53.456151] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM4 latency 93 (93.0 usec) <7>[ 53.456235] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM5 latency 100 (100.0 usec) <7>[ 53.456314] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM0 latency 6 (6.0 usec) <7>[ 53.456392] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM1 latency 106 (106.0 usec) <7>[ 53.456470] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM2 latency 106 (106.0 usec) <7>[ 53.456547] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM3 latency 106 (106.0 usec) <7>[ 53.456624] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM4 latency 106 (106.0 usec) <7>[ 53.456699] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM5 latency 106 (106.0 usec) <7>[ 53.459636] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 0: <7>[ 53.459768] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x8f074 = 0x86fc0 <7>[ 53.459915] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x8f034 = 0xc003b400 (EVT_CTL) <7>[ 53.460069] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x8f004 = 0x4240408 (EVT_HTP) <7>[ 53.460206] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x8f044 = 0xc0023200 (EVT_CTL) <7>[ 53.460337] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x8f014 = 0x57c45700 (EVT_HTP) <7>[ 53.460478] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 1: <7>[ 53.460610] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f074 = 0x97fc0 <7>[ 53.460740] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f040 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 53.460876] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f010 = 0x28542840 (EVT_HTP) <7>[ 53.461004] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f03c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 53.461221] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f00c = 0x29802864 (EVT_HTP) <7>[ 53.461441] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f044 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 53.461651] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f014 = 0x398c394c (EVT_HTP) <7>[ 53.461885] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 2: <7>[ 53.462106] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f474 = 0x9ffc0 <7>[ 53.462310] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f440 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 53.462513] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f410 = 0xa9bca9a8 (EVT_HTP) <7>[ 53.462718] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f43c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 53.462941] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f40c = 0xaae8a9cc (EVT_HTP) <7>[ 53.463152] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f444 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 53.463377] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f414 = 0xbabcba7c (EVT_HTP) <7>[ 53.463666] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 3: <7>[ 53.463897] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f874 = 0x547c0 <7>[ 53.464100] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f840 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 53.464299] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f810 = 0x26dc26c8 (EVT_HTP) <7>[ 53.464495] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f83c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 53.464685] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f80c = 0x280826ec (EVT_HTP) <7>[ 53.464884] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f844 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 53.465071] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f814 = 0x37dc379c (EVT_HTP) <7>[ 53.465585] xe 0000:00:02.0: [drm:intel_display_driver_probe_nogem [xe]] 3 display pipes available. <7>[ 53.470229] xe 0000:00:02.0: [drm:intel_cdclk_read_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 53.470462] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max CD clock rate: 652800 kHz <7>[ 53.470686] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max dotclock rate: 1305600 kHz <7>[ 53.470971] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:207:DDI A/PHY A] Using AUX CH A (VBT) <7>[ 53.471290] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding eDP connector on [ENCODER:207:DDI A/PHY A] <7>[ 53.471635] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel type (VBT): 2 <7>[ 53.471864] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Selected panel type (VBT): 2 <7>[ 53.472069] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] DRRS supported mode is seamless <7>[ 53.472282] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7>[ 53.472517] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT initial LVDS value 300 <7>[ 53.472734] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002 <7>[ 53.472951] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel name: LFP_PanelName <7>[ 53.473154] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Seamless DRRS min refresh rate: 0 Hz <7>[ 53.473351] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7>[ 53.473578] xe 0000:00:02.0: [drm:intel_pps_init [xe]] [ENCODER:207:DDI A/PHY A] initial power sequencer: PPS 0 <7>[ 53.473918] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 53.474108] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 53.474287] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 53.474488] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 53.474679] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 53.475009] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 53.475300] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <6>[ 53.476807] xe 0000:00:02.0: [drm] Finished loading DMC firmware i915/xe2lpd_dmc.bin (v2.29) <7>[ 53.476829] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on <7>[ 53.477126] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7>[ 53.478250] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 53.478665] xe 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 7.3 SW-rev 0.0 quirks 0x0000 <7>[ 53.479091] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] eDP DPCD: 05 83 85 04 1e <7>[ 53.479702] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] eDP panel supports PSR version 3 <7>[ 53.480091] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] PSR2 supported <7>[ 53.481929] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 53.491293] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 53.491307] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.491309] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.491311] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 53.491315] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 53.491319] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.491320] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 53.491326] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.491328] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 53.491331] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.491377] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.491380] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.491381] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.491400] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:208:eDP-1] using preferred EDID fixed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 53.491556] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:208:eDP-1] using alternate EDID fixed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.491922] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:208:eDP-1] Performing OUI wait (0 ms) <7>[ 53.492290] xe 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [xe]] [CONNECTOR:208:eDP-1] Detected unsupported HDR backlight interface version 0 <7>[ 53.492420] xe 0000:00:02.0: [drm:intel_panel_init [xe]] [CONNECTOR:208:eDP-1] DRRS type: seamless <7>[ 53.492572] xe 0000:00:02.0: [drm:cnp_setup_backlight [xe]] [CONNECTOR:208:eDP-1] Using native PCH PWM for backlight control (controller=0) <7>[ 53.492728] xe 0000:00:02.0: [drm:intel_backlight_setup [xe]] [CONNECTOR:208:eDP-1] backlight initialized, enabled, brightness 192000/192000 <7>[ 53.492910] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 53.493013] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 53.493112] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 53.493204] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 53.493290] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 53.493412] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 53.493619] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:216:DDI TC1/PHY TC1] Using AUX CH USBC1 (VBT) <7>[ 53.493782] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 53.493911] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:216:DDI TC1/PHY TC1] <7>[ 53.494278] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:228:DDI TC2/PHY TC2] Using AUX CH USBC2 (VBT) <7>[ 53.494408] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 53.494526] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:228:DDI TC2/PHY TC2] <7>[ 53.494755] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:236:DDI TC3/PHY TC3] Using AUX CH USBC3 (VBT) <7>[ 53.494891] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 53.495020] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:236:DDI TC3/PHY TC3] <7>[ 53.495489] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] hw state readout: enabled <7>[ 53.495610] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] hw state readout: disabled <7>[ 53.495726] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] hw state readout: disabled <7>[ 53.495817] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] hw state readout: enabled, pipe A <7>[ 53.495920] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A <7>[ 53.496016] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A <7>[ 53.496112] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A <7>[ 53.496201] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A <7>[ 53.496287] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] hw state readout: disabled, pipe A <7>[ 53.496373] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] hw state readout: disabled, pipe B <7>[ 53.496458] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] hw state readout: disabled, pipe B <7>[ 53.496544] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] hw state readout: disabled, pipe B <7>[ 53.496628] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] hw state readout: disabled, pipe B <7>[ 53.496712] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] hw state readout: disabled, pipe B <7>[ 53.496797] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] hw state readout: disabled, pipe B <7>[ 53.496889] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] hw state readout: disabled, pipe C <7>[ 53.496983] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] hw state readout: disabled, pipe C <7>[ 53.497074] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] hw state readout: disabled, pipe C <7>[ 53.497163] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] hw state readout: disabled, pipe C <7>[ 53.497251] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] hw state readout: disabled, pipe C <7>[ 53.497339] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] hw state readout: disabled, pipe C <7>[ 53.498125] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7>[ 53.498241] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:207:DDI A/PHY A] hw state readout: enabled, pipe A <7>[ 53.498328] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 53.498413] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:216:DDI TC1/PHY TC1] hw state readout: disabled, pipe A <7>[ 53.498490] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:218:DP-MST A] hw state readout: disabled, pipe A <7>[ 53.498566] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:219:DP-MST B] hw state readout: disabled, pipe B <7>[ 53.498642] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:220:DP-MST C] hw state readout: disabled, pipe C <7>[ 53.498720] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 53.498801] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:228:DDI TC2/PHY TC2] hw state readout: disabled, pipe A <7>[ 53.498887] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:230:DP-MST A] hw state readout: disabled, pipe A <7>[ 53.498968] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:231:DP-MST B] hw state readout: disabled, pipe B <7>[ 53.499047] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:232:DP-MST C] hw state readout: disabled, pipe C <7>[ 53.499136] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 53.499221] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:236:DDI TC3/PHY TC3] hw state readout: disabled, pipe A <7>[ 53.499302] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:238:DP-MST A] hw state readout: disabled, pipe A <7>[ 53.499380] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:239:DP-MST B] hw state readout: disabled, pipe B <7>[ 53.499457] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:240:DP-MST C] hw state readout: disabled, pipe C <7>[ 53.499556] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:208:eDP-1] hw state readout: enabled <7>[ 53.499649] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:217:DP-1] hw state readout: disabled <7>[ 53.499746] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:229:DP-2] hw state readout: disabled <7>[ 53.499841] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:237:DP-3] hw state readout: disabled <7>[ 53.500021] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] min_cdclk 173855 kHz <7>[ 53.500119] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] min_cdclk 0 kHz <7>[ 53.500212] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] min_cdclk 0 kHz <7>[ 53.500296] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] min_cdclk 0 kHz <7>[ 53.500375] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] min_cdclk 0 kHz <7>[ 53.500450] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] min_cdclk 0 kHz <7>[ 53.500525] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] min_cdclk 173855 kHz <7>[ 53.500601] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] min_cdclk 0 kHz <7>[ 53.500675] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] min_cdclk 0 kHz <7>[ 53.500748] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] min_cdclk 0 kHz <7>[ 53.500822] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] min_cdclk 0 kHz <7>[ 53.500906] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] min_cdclk 0 kHz <7>[ 53.500990] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] min_cdclk 0 kHz <7>[ 53.501073] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] min_cdclk 0 kHz <7>[ 53.501148] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] min_cdclk 0 kHz <7>[ 53.501217] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] min_cdclk 0 kHz <7>[ 53.501293] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] min_cdclk 0 kHz <7>[ 53.501369] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] min_cdclk 0 kHz <7>[ 53.501445] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] min_cdclk 0 kHz <7>[ 53.501522] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] min_cdclk 0 kHz <7>[ 53.501602] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] min_cdclk 0 kHz <7>[ 53.501834] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:88:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no <7>[ 53.501934] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:146:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 53.502025] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:204:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 53.502111] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 1390840 num active planes 1 <7>[ 53.502219] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0 <7>[ 53.502320] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0 <7>[ 53.502449] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: enabled, CMTG B: disabled, Transcoder A secondary: yes, Transcoder B secondary: no <7>[ 53.502552] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] Disabling CMTG A <7>[ 53.502777] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [setup_hw_state] <7>[ 53.502897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 53.503012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7>[ 53.503114] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 53.503208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 53.503301] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 53.503392] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 53.503483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64 <7>[ 53.503574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 53.503664] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 53.503752] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 53.503840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7>[ 53.503944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 53.504038] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7>[ 53.504134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 53.504221] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1 <7>[ 53.504307] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: yes, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 105 vsync start: 103, vsync end: 96 <7>[ 53.504393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1801, vmax vblank: 1801, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 53.504483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.504576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.504668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 53.504761] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.504846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 53.504954] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 53.505063] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 53.505160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 53.505246] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 53.505329] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 53.505411] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x41eb0, dpll_md: 0xf42110, fp0: 0xf8, fp1: 0x1000000 <7>[ 53.505493] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0 <7>[ 53.505574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 53.505655] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 53.505735] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.505815] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.505911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.506000] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 53.506086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 53.506171] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.506250] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.506328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.506406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 53.506483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7>[ 53.506567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [setup_hw_state] <7>[ 53.506654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [setup_hw_state] <7>[ 53.506979] xe 0000:00:02.0: [drm:skl_get_initial_plane_config [xe]] [CRTC:88:pipe A][PLANE:33:plane 1A] with fb: size=2880x1800@32, offset=fec00000, pitch 11520, size 0x13c6800 <7>[ 53.507089] xe 0000:00:02.0: [drm:intel_plane_disable_noatomic [xe]] Disabling [PLANE:33:plane 1A] on [CRTC:88:pipe A] <6>[ 53.520653] xe 0000:00:02.0: [drm] Tile0: GT0: Using GuC firmware from xe/lnl_guc_70.bin version 70.53.0 <7>[ 53.524184] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003543f7 <7>[ 53.524285] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000000 <7>[ 53.524359] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000000 <7>[ 53.524430] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 53.524497] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d2 <7>[ 53.524562] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 53.524626] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 53.524688] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 53.524749] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 53.524808] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 53.524881] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 53.524940] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 53.525000] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 53.525061] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 53.525123] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 53.525237] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [6144K, 832K) <7>[ 53.535899] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 9ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 53.536757] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 53.537056] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (geometry): 00000000,00000000,0000007f <7>[ 53.537175] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (compute): 00000000,00000000,0000007f <7>[ 53.537271] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU mask per DSS: 000000ff <7>[ 53.537362] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU type: simd16 <7>[ 53.537452] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: L3 bank mask: 00000000,000000ff <6>[ 54.178137] xe 0000:00:02.0: [drm] Tile0: GT0: ccs1 fused off <6>[ 54.178141] xe 0000:00:02.0: [drm] Tile0: GT0: ccs2 fused off <6>[ 54.178142] xe 0000:00:02.0: [drm] Tile0: GT0: ccs3 fused off <7>[ 54.178275] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add rcs0 whitelist to engine <7>[ 54.178391] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 54.178501] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 54.178601] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 54.178738] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs0 whitelist to engine <7>[ 54.178881] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs8 whitelist to engine <7>[ 54.179035] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add ccs0 whitelist to engine <7>[ 54.179124] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 54.179211] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 54.179294] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 54.180330] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying GT save-restore MMIOs <7>[ 54.180418] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x4148] = 0x00000000 <7>[ 54.180510] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x8828] = 0x00800000 <7>[ 54.180595] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb104] = 0x08104440 <7>[ 54.180678] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb108] = 0x30200000 <7>[ 54.180759] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb154] = 0x00020000 <7>[ 54.180838] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb158] = 0x0000007f <7>[ 54.180932] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: flag:0x1 <7>[ 54.181014] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: mocs entries: 16 <7>[ 54.181094] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[0] 0x4000 0xc <7>[ 54.181175] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[1] 0x4004 0x10c <7>[ 54.181251] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[2] 0x4008 0x130 <7>[ 54.181327] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[3] 0x400c 0x13c <7>[ 54.181401] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[4] 0x4010 0x100 <7>[ 54.181475] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[5] 0x4014 0x100 <7>[ 54.181549] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[6] 0x4018 0x100 <7>[ 54.181623] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[7] 0x401c 0x100 <7>[ 54.181697] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[8] 0x4020 0x100 <7>[ 54.181771] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[9] 0x4024 0x100 <7>[ 54.181844] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[10] 0x4028 0x100 <7>[ 54.181932] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[11] 0x402c 0x100 <7>[ 54.182006] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[12] 0x4030 0x100 <7>[ 54.182080] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[13] 0x4034 0x100 <7>[ 54.182153] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[14] 0x4038 0x100 <7>[ 54.182226] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[15] 0x403c 0x100 <7>[ 54.182292] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying rcs0 save-restore MMIOs <7>[ 54.182367] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x2050] = 0x10001000 <7>[ 54.182442] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20c4] = 0x3f7e0306 <7>[ 54.182515] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20d4] = 0xc080c080 <7>[ 54.182589] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d0] = 0x1000dafc <7>[ 54.182660] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d4] = 0x1000db01 <7>[ 54.182733] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d8] = 0x0000db1c <7>[ 54.182808] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe194] = 0x00400040 <7>[ 54.182898] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe48c] = 0x02000200 <7>[ 54.182973] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe49c] = 0x40004000 <7>[ 54.183053] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4c4] = 0x08400840 <7>[ 54.183128] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4f0] = 0x00020002 <7>[ 54.183207] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe530] = 0x00000400 <7>[ 54.183280] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7c8] = 0x00002000 <7>[ 54.183352] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7cc] = 0x00009000 <7>[ 54.183697] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs0 save-restore MMIOs <7>[ 54.183767] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x22050] = 0x10001000 <7>[ 54.183832] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220c4] = 0x3f7e0306 <7>[ 54.183909] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220d4] = 0xc080c080 <7>[ 54.184257] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs8 save-restore MMIOs <7>[ 54.184332] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee050] = 0x10001000 <7>[ 54.184402] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0c4] = 0x3f7e0306 <7>[ 54.184470] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0d4] = 0xc080c080 <7>[ 54.184766] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying ccs0 save-restore MMIOs <7>[ 54.184833] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a050] = 0x10001000 <7>[ 54.184909] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0c4] = 0x3f7e0306 <7>[ 54.184980] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0d4] = 0xc080c080 <7>[ 54.185052] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d0] = 0x1000dafc <7>[ 54.185120] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d4] = 0x1000db01 <7>[ 54.185187] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d8] = 0x0000db1c <7>[ 54.185618] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled <7>[ 54.185747] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003543f7 <7>[ 54.185820] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000800 <7>[ 54.185900] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000014 <7>[ 54.185969] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 54.186039] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d2 <7>[ 54.186109] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 54.186180] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 54.186253] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 54.186315] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 54.186376] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 54.186434] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 54.186492] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 54.186548] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 54.186609] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 54.186692] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT0: using 65535 GuC IDs <7>[ 54.186844] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT0: using 256 doorbells <7>[ 54.188373] xe 0000:00:02.0: [drm:guc_buf_cache_init [xe]] Tile0: GT0: reusable buffer with 2048 dwords at 0xd19000 for xe_guc_buf_cache_init_with_size [xe] <7>[ 54.190794] xe 0000:00:02.0: [drm:xe_guc_capture_steered_list_init [xe]] Tile0: GT0: capture found 42 ext-regs. <7>[ 54.206684] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT0: Updated ADS capture size 20480 (was 45056) <7>[ 54.216956] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 9ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 54.217302] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 54.218254] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC rcs0 WA job: 4138 dwords <7>[ 54.218364] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x5588] = 0x04000400 <7>[ 54.218434] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6204] = 0x00400040 <7>[ 54.218500] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6208] = 0x00200020 <7>[ 54.218565] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x62a8] = 0x02400240 <7>[ 54.218634] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7010] = 0x40004000 <7>[ 54.218702] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7044] = 0x04200420 <7>[ 54.218772] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x83a8] = 0x20002000 <7>[ 54.218844] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6210] = ~0x18000|0x18000 <7>[ 54.221855] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC bcs0 WA job: 27 dwords <7>[ 54.221967] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x22204] = ~0x7e7e|0x606 <7>[ 54.222066] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <7>[ 54.225112] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC ccs0 WA job: 0 dwords <7>[ 54.225255] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <6>[ 54.228985] xe 0000:00:02.0: [drm] Tile0: GT1: Using GuC firmware from xe/lnl_guc_70.bin version 70.53.0 <7>[ 54.232914] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df63f7 <7>[ 54.233033] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 54.233131] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000000 <7>[ 54.233223] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 54.233313] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e16 <7>[ 54.233402] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 54.233489] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 54.233575] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 54.233662] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 54.233748] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 54.233832] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 54.233950] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 54.234037] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 54.234122] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <6>[ 54.235497] xe 0000:00:02.0: [drm] Tile0: GT1: Using HuC firmware from xe/lnl_huc.bin version 9.4.13 <6>[ 54.237869] xe 0000:00:02.0: [drm] Tile0: GT1: Using GSC firmware from xe/lnl_gsc_1.bin version 104.0.5.1429 <6>[ 54.239064] mei_gsc_proxy 0000:00:16.0-0f73db04-97ab-4125-b893-e904ad0d5464: bound 0000:00:02.0 (ops xe_gsc_proxy_component_ops [xe]) <7>[ 54.239191] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 54.239342] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [5136K, 832K) <7>[ 54.259922] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 19ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 54.260396] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 54.260624] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (geometry): 00000000,00000000,00000000 <7>[ 54.260828] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (compute): 00000000,00000000,00000000 <7>[ 54.261085] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU mask per DSS: 00000000 <7>[ 54.261300] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU type: simd16 <7>[ 54.261511] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: L3 bank mask: 00000000,0000000f <6>[ 54.261716] xe 0000:00:02.0: [drm] Tile0: GT1: vcs1 fused off <6>[ 54.261720] xe 0000:00:02.0: [drm] Tile0: GT1: vcs2 fused off <6>[ 54.261723] xe 0000:00:02.0: [drm] Tile0: GT1: vcs3 fused off <6>[ 54.261725] xe 0000:00:02.0: [drm] Tile0: GT1: vcs4 fused off <6>[ 54.261727] xe 0000:00:02.0: [drm] Tile0: GT1: vcs5 fused off <6>[ 54.261730] xe 0000:00:02.0: [drm] Tile0: GT1: vcs6 fused off <6>[ 54.261732] xe 0000:00:02.0: [drm] Tile0: GT1: vcs7 fused off <6>[ 54.261734] xe 0000:00:02.0: [drm] Tile0: GT1: vecs1 fused off <6>[ 54.261737] xe 0000:00:02.0: [drm] Tile0: GT1: vecs2 fused off <6>[ 54.261739] xe 0000:00:02.0: [drm] Tile0: GT1: vecs3 fused off <7>[ 54.261862] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vcs0 whitelist to engine <7>[ 54.262264] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vecs0 whitelist to engine <7>[ 54.262653] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add gsccs0 whitelist to engine <7>[ 54.264736] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying GT save-restore MMIOs <7>[ 54.265056] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x4148] = 0x00000000 <7>[ 54.265385] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x82a8] = 0x00800000 <7>[ 54.265645] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb604] = 0x08104440 <7>[ 54.265893] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb608] = 0x30200000 <7>[ 54.266121] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb654] = 0x00020000 <7>[ 54.266357] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb658] = 0x0000007f <7>[ 54.266571] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f08] = 0x00000020 <7>[ 54.266767] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f10] = 0x00400000 <7>[ 54.266985] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f1c] = 0x00000008 <7>[ 54.267210] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: flag:0x1 <7>[ 54.267414] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: mocs entries: 16 <7>[ 54.267623] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[0] 0x4000 0xc <7>[ 54.267814] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[1] 0x4004 0x10c <7>[ 54.268034] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[2] 0x4008 0x130 <7>[ 54.268207] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[3] 0x400c 0x13c <7>[ 54.268377] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[4] 0x4010 0x100 <7>[ 54.268538] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[5] 0x4014 0x100 <7>[ 54.268690] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[6] 0x4018 0x100 <7>[ 54.268839] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[7] 0x401c 0x100 <7>[ 54.269041] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[8] 0x4020 0x100 <7>[ 54.269191] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[9] 0x4024 0x100 <7>[ 54.269328] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[10] 0x4028 0x100 <7>[ 54.269458] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[11] 0x402c 0x100 <7>[ 54.269585] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[12] 0x4030 0x100 <7>[ 54.269711] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[13] 0x4034 0x100 <7>[ 54.269831] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[14] 0x4038 0x100 <7>[ 54.269997] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[15] 0x403c 0x100 <7>[ 54.270143] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vcs0 save-restore MMIOs <7>[ 54.270286] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c0050] = 0x10001000 <7>[ 54.270447] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c00d4] = 0xc000c000 <7>[ 54.270958] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vecs0 save-restore MMIOs <7>[ 54.271084] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c8050] = 0x10001000 <7>[ 54.271206] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c80d4] = 0xc000c000 <7>[ 54.271665] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying gsccs0 save-restore MMIOs <7>[ 54.271786] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a050] = 0x10001000 <7>[ 54.271919] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a0d4] = 0xc000c000 <7>[ 54.272584] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled <7>[ 54.272740] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df63f7 <7>[ 54.272857] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 54.272964] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000014 <7>[ 54.273064] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 54.273158] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e16 <7>[ 54.273249] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 54.273339] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 54.273433] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 54.273520] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 54.273601] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 54.273680] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 54.273758] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 54.273836] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 54.273931] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <7>[ 54.274045] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT1: using 65535 GuC IDs <7>[ 54.274160] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT1: using 256 doorbells <7>[ 54.275456] xe 0000:00:02.0: [drm:guc_buf_cache_init [xe]] Tile0: GT1: reusable buffer with 2048 dwords at 0x1984000 for xe_guc_buf_cache_init_with_size [xe] <7>[ 54.292787] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT1: Updated ADS capture size 24576 (was 45056) <7>[ 54.314125] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 20ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 54.314617] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 54.315838] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vcs0 WA job: 0 dwords <7>[ 54.316118] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 54.318846] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vecs0 WA job: 0 dwords <7>[ 54.319150] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 54.322366] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC gsccs0 WA job: 0 dwords <7>[ 54.322690] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 54.366657] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GuC <7>[ 54.367809] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 54.368256] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 54.368634] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 54.369001] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 54.369945] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT0: oa_unit 0, type 0, Engines: rcs0 ccs0 <7>[ 54.370266] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 1, type 2, Engines: <7>[ 54.370567] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 2, type 1, Engines: vcs0 vecs0 <7>[ 54.372428] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 0: start 0x90008 <7>[ 54.372873] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 1: start 0x90108 <7>[ 54.373255] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 2: start 0x90208 <7>[ 54.373619] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 3: start 0x90308 <7>[ 54.373985] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 4: start 0x903c8 <7>[ 54.374328] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 0: start 0x98008 <7>[ 54.374662] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 1: start 0x98108 <7>[ 54.375002] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 2: start 0x98208 <7>[ 54.375333] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 3: start 0x98308 <7>[ 54.375656] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 4: start 0x983c8 <7>[ 54.375988] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 0: start 0x52008 <7>[ 54.376309] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 1: start 0x52108 <7>[ 54.376627] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 2: start 0x52208 <7>[ 54.376938] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 3: start 0x52308 <7>[ 54.377229] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 4: start 0x523c8 <7>[ 54.378026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7>[ 54.378362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:88:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7>[ 54.378704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45 <7>[ 54.379082] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [fastset] <7>[ 54.379478] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [fastset] <7>[ 54.381590] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: A) <7>[ 54.381886] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes) <7>[ 54.397691] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:146:pipe B] <7>[ 54.398205] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:204:pipe C] <7>[ 54.412951] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:208:eDP-1] adding connector to sysfs <7>[ 54.418862] xe 0000:00:02.0: [drm:intel_backlight_device_register [xe]] [CONNECTOR:208:eDP-1] backlight device intel_backlight registered <7>[ 54.419145] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:208:eDP-1] Registered panel device 'card0-eDP-1', has fwnode: yes <7>[ 54.419365] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:208:eDP-1] Panel prepare <7>[ 54.420017] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7>[ 54.421799] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:208:eDP-1] generating connector hotplug event <7>[ 54.421916] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:217:DP-1] adding connector to sysfs <7>[ 54.422518] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1 <7>[ 54.423446] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:217:DP-1] generating connector hotplug event <7>[ 54.423502] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:229:DP-2] adding connector to sysfs <7>[ 54.424015] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2 <7>[ 54.424945] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:229:DP-2] generating connector hotplug event <7>[ 54.424989] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:237:DP-3] adding connector to sysfs <7>[ 54.425416] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC3/DDI TC3/PHY TC3 bus for card0-DP-3 <7>[ 54.426114] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:237:DP-3] generating connector hotplug event <6>[ 54.426147] [drm] Initialized xe 1.1.0 for 0000:00:02.0 on minor 0 <7>[ 54.426195] xe 0000:00:02.0: [drm:intel_opregion_resume [xe]] 4 outputs detected <6>[ 54.438851] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6>[ 54.442340] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5 <7>[ 54.443365] xe 0000:00:02.0: [drm:intel_audio_init [xe]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010) <7>[ 54.443521] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480 <7>[ 54.443978] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix <6>[ 54.443983] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 54.445984] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [xe]) <7>[ 54.446940] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010 <7>[ 54.447001] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 54.447453] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.448184] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:217:DP-1] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 54.448377] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 54.448593] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.448782] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:229:DP-2] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 54.448838] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [PLANE:33:plane 1A] no fb, skipping <7>[ 54.449031] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:146:pipe B] not active, skipping <7>[ 54.449038] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 54.449200] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:204:pipe C] not active, skipping <7>[ 54.449247] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.449363] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] no active fbs found, not using BIOS config <7>[ 54.449434] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:237:DP-3] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 54.449610] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7>[ 54.449901] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 54.450729] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 54.450739] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 54.451885] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9b01 <7>[ 54.452716] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL <7>[ 54.452725] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled <7>[ 54.452722] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 54.453112] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 54.453303] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.453486] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.453780] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 54.453788] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.453790] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.453792] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 54.453796] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 54.453800] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.453802] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 54.453809] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.453811] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 54.453815] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.453846] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 54.454064] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 54.454245] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7>[ 54.455153] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] status updated from unknown to connected <5>[ 54.455447] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.455450] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.455453] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.455521] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 54.455528] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 54.455532] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 54.455537] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 54.455542] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 54.455765] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 54.455770] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 54.455773] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 54.456142] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7>[ 54.456532] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 54.456537] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 54.456540] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 54.456722] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 54.456725] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 54.456729] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 54.456731] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 54.456733] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 54.456822] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 54.456841] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 54.456844] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7>[ 54.456953] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 54.457037] xe 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7>[ 54.457047] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] no BIOS fb, allocating a new one <7>[ 54.466093] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] allocated 2880x1800 fb: 0x01da5000 <6>[ 54.467716] fbcon: xedrmfb (fb0) is primary device <7>[ 54.469746] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:208:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7>[ 54.469983] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:207:DDI A/PHY A][CRTC:88:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7>[ 54.470136] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7>[ 54.470299] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7>[ 54.470450] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:207:DDI A/PHY A] [CRTC:88:pipe A] <7>[ 54.470591] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 8102230/8388608 link 675185/524288, found tu 64, data 6329869/8388608 link 421991/524288) <7>[ 54.470732] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dpll_hw_state.cx0pll C10 <7>[ 54.470889] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected: <7>[ 54.471031] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: yes, <7>[ 54.471170] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] quot: 40960, rem: 0, den: 1, <7>[ 54.471306] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 140, tx_clk_div: 1. <7>[ 54.471440] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 54.471575] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 54.471719] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0 <7>[ 54.471856] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 54.471995] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 54.472134] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 54.472279] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23 <7>[ 54.472409] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found: <7>[ 54.472539] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: no, <7>[ 54.472666] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 225, tx_clk_div: 1. <7>[ 54.472791] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 54.472932] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 54.473063] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <6>[ 54.473198] xe 0000:00:02.0: [drm] Tile0: GT1: found GSC cv104.1.0 <7>[ 54.473192] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 54.473317] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 54.473439] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 54.473559] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7>[ 54.473653] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC FW async load completed <7>[ 54.473685] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30) <7>[ 54.473829] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in port_clock (expected 270000, found 432000) <7>[ 54.473977] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0) <7>[ 54.474108] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] fastset requirement not met, forcing full modeset <7>[ 54.474292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7>[ 54.474427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm <7>[ 54.474563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7>[ 54.474693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7>[ 54.474813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <7>[ 54.474936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 54.475047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 54.475498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475605] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.475828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 54.475944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 54.476370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 54.476776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.476993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 54.477323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:88:pipe A] data rate 1390840 num active planes 1 <7>[ 54.477471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7>[ 54.477604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7>[ 54.477733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 54.477866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 54.477989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7>[ 54.478208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [modeset] <7>[ 54.478353] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 54.478483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7>[ 54.478608] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 54.478728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 54.478858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 54.478982] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 54.479114] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7>[ 54.479248] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 54.479376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 54.479502] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 54.479634] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7>[ 54.479767] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 54.479985] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7>[ 54.480109] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7>[ 54.480227] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7>[ 54.480344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7>[ 54.480459] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7>[ 54.480569] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7>[ 54.480678] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7>[ 54.480788] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 54.480908] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7>[ 54.481017] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7>[ 54.481127] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 54.481233] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 54.481338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 54.481442] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 54.481547] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 54.481651] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 54.481754] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 54.482041] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 54.482160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 54.482277] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 54.482392] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 54.482503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x69780, dpll_md: 0x42110, fp0: 0x1a2, fp1: 0x1000000 <7>[ 54.482614] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7>[ 54.482724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 54.482834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 54.482957] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483064] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483171] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483276] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 54.483382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 54.483485] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483586] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483687] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 54.483790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 54.483903] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7>[ 54.484012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:209] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7>[ 54.484127] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7>[ 54.484236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0 <7>[ 54.484345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no <7>[ 54.484452] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no <7>[ 54.484556] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no <7>[ 54.484658] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no <7>[ 54.484760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no <7>[ 54.491197] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 54.491321] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 54.491427] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 54.491531] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 54.491631] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 54.491730] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 54.491827] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 54.492008] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 54.492136] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 54.492261] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 54.492372] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 54.492475] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 54.492586] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 54.492709] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 54.492830] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 54.492962] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 54.493083] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 54.493194] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 54.493305] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 54.493406] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 54.493504] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 54.493602] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 54.493700] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 54.493796] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 54.493909] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 54.494024] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 54.494139] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 54.494248] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 54.494351] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 54.494453] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 54.494553] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 54.494650] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 54.494745] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 54.494838] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 54.494959] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 54.495069] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 54.496296] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GSC <6>[ 54.502853] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input6 <6>[ 54.503861] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input7 <6>[ 54.504561] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input8 <7>[ 54.505693] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM <7>[ 54.506057] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]] <6>[ 54.507030] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input9 <7>[ 54.712195] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 0 <7>[ 54.713368] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A <7>[ 54.714479] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power off <7>[ 54.714838] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power off time <7>[ 54.714923] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 54.715273] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7>[ 54.715417] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - short <7>[ 54.767564] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 54.767972] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - short <7>[ 54.774892] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 54.775296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A <7>[ 54.775283] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.776007] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0xffff0072 0x1341b072) <7>[ 54.776006] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.776327] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:207:DDI A/PHY A] <7>[ 54.776676] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:216:DDI TC1/PHY TC1] <7>[ 54.776983] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:218:DP-MST A] <7>[ 54.777250] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST B] <7>[ 54.777510] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST C] <7>[ 54.777768] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:228:DDI TC2/PHY TC2] <7>[ 54.778052] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:230:DP-MST A] <7>[ 54.778317] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DP-MST B] <7>[ 54.778574] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:232:DP-MST C] <7>[ 54.778826] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:236:DDI TC3/PHY TC3] <7>[ 54.779104] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:238:DP-MST A] <7>[ 54.779366] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DP-MST B] <7>[ 54.779612] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:240:DP-MST C] <7>[ 54.779903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7>[ 54.780950] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power on <7>[ 54.781410] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power cycle (494 ms remaining) <7>[ 54.800852] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 54.801235] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - long <7>[ 54.801601] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10 <7>[ 54.801970] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.905608] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC proxy init completed <7>[ 55.279975] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060 <7>[ 55.380242] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 55.380641] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power on <7>[ 55.381073] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7>[ 55.417447] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 55.417870] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - long <7>[ 55.418248] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20 <7>[ 55.418807] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 55.504555] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 55.504565] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 55.504681] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 55.588976] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 55.592452] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on <7>[ 55.593189] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7>[ 55.595930] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 55.597223] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Reloading eDP link rates <7>[ 55.598389] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05 <7>[ 55.599928] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7>[ 55.601266] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7>[ 55.602597] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Clock recovery OK <7>[ 55.603156] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS4 <7>[ 55.604883] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7>[ 55.605404] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4 <7>[ 55.606404] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A <7>[ 55.607168] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]] <7>[ 55.607676] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A <7>[ 55.608273] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 192000 <7>[ 55.624149] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7>[ 55.626906] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:208:eDP-1] <7>[ 55.627577] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:88:pipe A] <7>[ 55.629240] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp <7>[ 55.630907] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072) <7>[ 55.632327] xe 0000:00:02.0: [drm:intel_backlight_device_update_status [xe]] updating intel_backlight, brightness=9600/192000 <7>[ 55.632823] xe 0000:00:02.0: [drm:intel_panel_actually_set_backlight [xe]] [CONNECTOR:208:eDP-1] set backlight level = 13892 <6>[ 55.633465] Console: switching to colour frame buffer device 180x56 <6>[ 55.642825] xe 0000:00:02.0: [drm] fb0: xedrmfb frame buffer device <7>[ 55.649926] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display version: 20 <7>[ 55.650322] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display stepping: B0 <7>[ 55.650477] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: cursor_needs_physical: no <7>[ 55.650626] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_crawl: yes <7>[ 55.650772] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_squash: yes <7>[ 55.650940] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ddi: yes <7>[ 55.651088] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dp_mst: yes <7>[ 55.651234] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsb: yes <7>[ 55.651383] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_fpga_dbg: yes <7>[ 55.651533] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_gmch: no <7>[ 55.651686] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hotplug: yes <7>[ 55.651840] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hti: no <7>[ 55.652006] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ipc: yes <7>[ 55.652165] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_overlay: no <7>[ 55.652326] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr: yes <7>[ 55.652486] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr_hw_tracking: no <7>[ 55.652652] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: overlay_needs_physical: no <7>[ 55.652821] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: supports_tv: no <7>[ 55.652998] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hdcp: yes <7>[ 55.653172] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dmc: yes <7>[ 55.653348] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsc: yes <7>[ 55.653532] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: rawclk rate: 38400 kHz <7>[ 55.654608] [drm:intel_dsm_detect.isra.0 [xe]] no _DSM method for intel device <7>[ 55.654881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC <7>[ 55.655183] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D <7>[ 55.655473] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C <7>[ 55.655731] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B <7>[ 55.659891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.660488] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.661830] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 55.662752] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 55.663143] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 55.663207] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] d3cold: capable=no <7>[ 55.675087] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7>[ 55.675117] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 55.675797] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 55.675822] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 55.676699] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 55.677340] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 55.677701] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 55.678065] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 55.678600] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 55.678615] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.678620] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.678623] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 55.678630] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 55.678637] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.678640] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 55.678658] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.678661] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 55.678668] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.678713] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 55.679014] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 55.679295] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5>[ 55.680277] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.680283] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.680287] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.680460] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 55.680483] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 55.680493] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 55.680503] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 55.680511] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 55.680865] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.681206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.681535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 55.681916] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 55.682212] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 55.682224] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 55.682232] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 55.682584] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 55.682877] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 55.682886] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 55.682892] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 55.683309] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 55.683598] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 55.683605] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 55.683613] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 55.683618] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 55.683623] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 55.683874] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 55.683925] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 55.683933] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config <7>[ 55.684010] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 55.686531] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 55.686799] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 55.691362] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7>[ 55.708363] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.708760] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.709180] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 55.724673] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7>[ 55.732298] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 55.733901] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 55.742279] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7>[ 55.742324] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 55.743374] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 55.743406] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 55.745127] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 55.745878] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 55.746339] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 55.746793] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 55.747650] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 55.747676] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.747682] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.747686] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 55.747695] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 55.747703] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.747708] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 55.747734] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.747738] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 55.747746] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.747822] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 55.748155] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 55.748471] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5>[ 55.749696] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.749703] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 55.749707] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 55.749951] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 55.749977] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 55.749988] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 55.750000] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 55.750012] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 55.750536] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 55.750550] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 55.750559] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 55.751018] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 55.751027] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 55.751035] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 55.751394] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 55.751402] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 55.751411] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 55.751417] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 55.751423] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 55.751780] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 55.751875] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 55.751886] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config <7>[ 55.752010] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 55.760241] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.760753] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.761273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 55.761730] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2 <7>[ 55.762305] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 55.762754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 55.790732] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7>[ 55.791802] [IGT] xe_module_load: finished subtest load, SUCCESS <7>[ 55.792599] [IGT] xe_module_load: exiting, ret=0 <7>[ 55.808906] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.809432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.809915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 56.783826] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 56.783947] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 56.784059] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 58.255226] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD off <7>[ 58.256000] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067