Oops#1 Part20
<7>[   52.993925] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding eDP connector on [ENCODER:392:DDI A/PHY A]
<7>[   52.994161] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel type (VBT): 2
<7>[   52.994320] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Selected panel type (VBT): 2
<7>[   52.994476] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] DRRS supported mode is seamless
<7>[   52.994638] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7>[   52.994793] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT initial LVDS value 300
<7>[   52.994944] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002
<7>[   52.995093] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel name: LFP_PanelName
<7>[   52.995253] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Seamless DRRS min refresh rate: 0 Hz
<7>[   52.995402] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7>[   52.995576] xe 0000:00:02.0: [drm:intel_pps_init [xe]] [ENCODER:392:DDI A/PHY A] initial power sequencer: PPS 0
<7>[   52.995830] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000
<7>[   52.995965] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000
Oops#1 Part19
<7>[   52.996096] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100
<7>[   52.996234] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500
<7>[   52.996356] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200
<7>[   52.996628] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7>[   52.996936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7>[   52.998206] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<6>[   52.998483] xe 0000:00:02.0: [drm] Finished loading DMC firmware i915/xe2lpd_dmc.bin (v2.29)
<7>[   52.998461] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7>[   53.024164] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7>[   53.037163] xe 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID  HW-rev 7.3 SW-rev 0.0 quirks 0x0000
<7>[   53.061155] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] eDP DPCD: 05 83 85 04 1e
<7>[   53.097148] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] eDP panel supports PSR version 3
<7>[   53.109148] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] PSR2 supported
Oops#1 Part18
<7>[   53.169167] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7>[   53.517177] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5>[   53.517187] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5>[   53.517190] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7>[   53.517191] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7>[   53.517193] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5>[   53.517195] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7>[   53.517197] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor 
<5>[   53.517200] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7>[   53.517201] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5>[   53.517203] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5>[   53.517239] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5>[   53.517241] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5>[   53.517242] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7>[   53.517257] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:393:eDP-1] using preferred EDID fixed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
Oops#1 Part17
<7>[   53.517378] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:393:eDP-1] using alternate EDID fixed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7>[   53.529149] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:393:eDP-1] Performing OUI wait (0 ms)
<7>[   53.541153] xe 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [xe]] [CONNECTOR:393:eDP-1] Detected unsupported HDR backlight interface version 0
<7>[   53.541292] xe 0000:00:02.0: [drm:intel_panel_init [xe]] [CONNECTOR:393:eDP-1] DRRS type: seamless
<7>[   53.541440] xe 0000:00:02.0: [drm:cnp_setup_backlight [xe]] [CONNECTOR:393:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7>[   53.541567] xe 0000:00:02.0: [drm:intel_backlight_setup [xe]] [CONNECTOR:393:eDP-1] backlight initialized, enabled, brightness 192000/192000
<7>[   53.541743] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000
<7>[   53.541855] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000
<7>[   53.541958] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100
<7>[   53.542052] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500
<7>[   53.542152] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200
Oops#1 Part16
<7>[   53.542277] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7>[   53.542486] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:401:DDI TC1/PHY TC1] Using AUX CH USBC1 (VBT)
<7>[   53.542676] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7>[   53.542819] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:401:DDI TC1/PHY TC1]
<7>[   53.543225] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:413:DDI TC2/PHY TC2] Using AUX CH USBC2 (VBT)
<7>[   53.543374] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7>[   53.543499] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:413:DDI TC2/PHY TC2]
<7>[   53.543748] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:421:DDI TC3/PHY TC3] Using AUX CH USBC3 (VBT)
<7>[   53.543882] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7>[   53.544006] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:421:DDI TC3/PHY TC3]
<7>[   53.544375] xe 0000:00:02.0: [drm:intel_vga_disable [xe]] VGA plane is disabled
<6>[   53.544493] xe 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io:owns=io+mem
<7>[   53.544913] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:151:pipe A] hw state readout: enabled
Oops#1 Part15
<7>[   53.545037] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:270:pipe B] hw state readout: disabled
<7>[   53.545166] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:389:pipe C] hw state readout: disabled
<7>[   53.545266] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:35:plane 1A] hw state readout: enabled, pipe A
<7>[   53.545365] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:65:plane 2A] hw state readout: disabled, pipe A
<7>[   53.545463] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:95:plane 3A] hw state readout: disabled, pipe A
<7>[   53.545561] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:125:plane 4A] hw state readout: disabled, pipe A
<7>[   53.545660] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:135:plane 5A] hw state readout: disabled, pipe A
<7>[   53.545758] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:145:cursor A] hw state readout: disabled, pipe A
<7>[   53.545853] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:154:plane 1B] hw state readout: disabled, pipe B
<7>[   53.545947] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:184:plane 2B] hw state readout: disabled, pipe B
<7>[   53.546040] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:214:plane 3B] hw state readout: disabled, pipe B
<7>[   53.546136] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:244:plane 4B] hw state readout: disabled, pipe B
<7>[   53.546226] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:254:plane 5B] hw state readout: disabled, pipe B
Oops#1 Part14
<7>[   53.546315] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:264:cursor B] hw state readout: disabled, pipe B
<7>[   53.546404] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:273:plane 1C] hw state readout: disabled, pipe C
<7>[   53.546491] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:303:plane 2C] hw state readout: disabled, pipe C
<7>[   53.546578] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:333:plane 3C] hw state readout: disabled, pipe C
<7>[   53.546664] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:363:plane 4C] hw state readout: disabled, pipe C
<7>[   53.546749] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:373:plane 5C] hw state readout: disabled, pipe C
<7>[   53.546835] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:383:cursor C] hw state readout: disabled, pipe C
<7>[   53.547907] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7>[   53.548029] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:392:DDI A/PHY A] hw state readout: enabled, pipe A
<7>[   53.548141] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7>[   53.548234] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:401:DDI TC1/PHY TC1] hw state readout: disabled, pipe A
<7>[   53.548326] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:403:DP-MST A] hw state readout: disabled, pipe A
Oops#1 Part13
<7>[   53.548414] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:404:DP-MST B] hw state readout: disabled, pipe B
<7>[   53.548501] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:405:DP-MST C] hw state readout: disabled, pipe C
<7>[   53.548592] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7>[   53.548679] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:413:DDI TC2/PHY TC2] hw state readout: disabled, pipe A
<7>[   53.548764] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:415:DP-MST A] hw state readout: disabled, pipe A
<7>[   53.548850] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:416:DP-MST B] hw state readout: disabled, pipe B
<7>[   53.548935] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:417:DP-MST C] hw state readout: disabled, pipe C
<7>[   53.549022] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7>[   53.549107] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:421:DDI TC3/PHY TC3] hw state readout: disabled, pipe A
<7>[   53.549207] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:423:DP-MST A] hw state readout: disabled, pipe A
<7>[   53.549296] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:424:DP-MST B] hw state readout: disabled, pipe B
<7>[   53.549381] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:425:DP-MST C] hw state readout: disabled, pipe C
Oops#1 Part12
<7>[   53.550397] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7>[   53.550502] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 0 hw state readout: pipe_mask 0x1, on 1
<7>[   53.550605] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7>[   53.550706] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TBT PLL hw state readout: pipe_mask 0x0, on 1
<7>[   53.550810] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0
<7>[   53.550913] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0
<7>[   53.551015] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0
<7>[   53.551112] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0
<7>[   53.551248] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:393:eDP-1] hw state readout: enabled
<7>[   53.551355] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:402:DP-1] hw state readout: disabled
<7>[   53.551458] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:414:DP-2] hw state readout: disabled
<7>[   53.551549] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:422:DP-3] hw state readout: disabled
<7>[   53.551706] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:35:plane 1A] min_cdclk 173855 kHz
<7>[   53.551791] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:65:plane 2A] min_cdclk 0 kHz
Oops#1 Part11
<7>[   53.551874] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:95:plane 3A] min_cdclk 0 kHz
<7>[   53.551955] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:125:plane 4A] min_cdclk 0 kHz
<7>[   53.552035] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:135:plane 5A] min_cdclk 0 kHz
<7>[   53.552113] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:145:cursor A] min_cdclk 0 kHz
<7>[   53.552210] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:151:pipe A] min_cdclk 173855 kHz
<7>[   53.552290] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:154:plane 1B] min_cdclk 0 kHz
<7>[   53.552369] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:184:plane 2B] min_cdclk 0 kHz
<7>[   53.552448] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:214:plane 3B] min_cdclk 0 kHz
<7>[   53.552526] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:244:plane 4B] min_cdclk 0 kHz
<7>[   53.552604] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:254:plane 5B] min_cdclk 0 kHz
<7>[   53.552685] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:264:cursor B] min_cdclk 0 kHz
<7>[   53.552768] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:270:pipe B] min_cdclk 0 kHz
<7>[   53.552849] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:273:plane 1C] min_cdclk 0 kHz
<7>[   53.552928] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:303:plane 2C] min_cdclk 0 kHz
<7>[   53.553006] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:333:plane 3C] min_cdclk 0 kHz
Oops#1 Part10
<7>[   53.553083] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:363:plane 4C] min_cdclk 0 kHz
<7>[   53.553169] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:373:plane 5C] min_cdclk 0 kHz
<7>[   53.553246] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:383:cursor C] min_cdclk 0 kHz
<7>[   53.553322] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:389:pipe C] min_cdclk 0 kHz
<7>[   53.553547] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:151:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no
<7>[   53.553629] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:270:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no
<7>[   53.553712] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:389:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no
<7>[   53.553794] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 1390840 num active planes 1
<7>[   53.553909] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0
<7>[   53.554026] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0
<7>[   53.554171] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: enabled, CMTG B: disabled, Transcoder A secondary: yes, Transcoder B secondary: no
<7>[   53.554286] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] Disabling CMTG A
<7>[   53.554546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [setup_hw_state]
Oops#1 Part9
<7>[   53.554673] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7>[   53.554786] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7>[   53.554894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7>[   53.555002] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7>[   53.555111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7>[   53.555233] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7>[   53.555339] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64
<7>[   53.555444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7>[   53.555550] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7>[   53.555653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7>[   53.555758] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7>[   53.555862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7>[   53.555966] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7>[   53.556074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
Oops#1 Part8
<7>[   53.556191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7>[   53.556296] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: yes, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 105 vsync start: 103, vsync end: 96
<7>[   53.556399] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1801, vmax vblank: 1801, vmin vtotal: 1906, vmax vtotal: 1906
<7>[   53.556500] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7>[   53.556600] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7>[   53.556701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7>[   53.556799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa
<7>[   53.556897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7>[   53.556994] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa
<7>[   53.557089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pixel rate 347710, min cdclk 173855, min voltage level 0
Oops#1 Part7
<7>[   53.557196] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7>[   53.557289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7>[   53.557381] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7>[   53.557472] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7>[   53.557564] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7>[   53.557654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7>[   53.557747] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7>[   53.557838] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: yes, 
<7>[   53.557929] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 40960, rem: 0, den: 1,
<7>[   53.558021] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 140, tx_clk_div: 1.
<7>[   53.558111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7>[   53.558212] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7>[   53.558310] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0
<7>[   53.558410] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7>[   53.558508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
Oops#1 Part6
<7>[   53.558605] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7>[   53.558701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23
<7>[   53.558796] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0
<7>[   53.558891] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7>[   53.558983] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7>[   53.559076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559360] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7>[   53.559450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7>[   53.559540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559629] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559720] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7>[   53.559808] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
Oops#1 Part5
<7>[   53.559897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:270:pipe B] enable: no [setup_hw_state]
<7>[   53.559986] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:389:pipe C] enable: no [setup_hw_state]
<7>[   53.560083] xe 0000:00:02.0: [drm:intel_dpll_sanitize_state [xe]] TBT PLL enabled but not in use, disabling
<7>[   53.560715] xe 0000:00:02.0: [drm:skl_get_initial_plane_config [xe]] [CRTC:151:pipe A][PLANE:35:plane 1A] with fb: size=2880x1800@32, offset=fec00000, pitch 11520, size 0x13c6800
<6>[   53.560819] xe 0000:00:02.0: [drm] Initial FB size exceeds half of stolen, discarding
<7>[   53.560820] xe 0000:00:02.0: [drm:intel_plane_disable_noatomic [xe]] Disabling [PLANE:35:plane 1A] on [CRTC:151:pipe A]
<1>[   53.567761] BUG: unable to handle page fault for address: 0000000000003244
<1>[   53.574684] #PF: supervisor read access in kernel mode
<1>[   53.579860] #PF: error_code(0x0000) - not-present page
<6>[   53.585033] PGD 0 P4D 0 
<4>[   53.587599] Oops: Oops: 0000 [#1] SMP NOPTI
<4>[   53.591819] CPU: 2 UID: 0 PID: 1881 Comm: xe_module_load Tainted: G     U              7.0.0-lgci-xe-xe-pw-164953v1-debug+ #1 PREEMPT(lazy) 
<4>[   53.604486] Tainted: [U]=USER
<4>[   53.607479] Hardware name: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D99.2508051732 08/05/2025
<4>[   53.619799] RIP: 0010:__xe_ggtt_insert_bo_at+0x1d6/0x870 [xe]
<4>[   53.625686] Code: e1 41 89 c7 58 5a 45 85 ff 0f 85 c8 00 00 00 49 8b 04 24 4c 8b 10 8b 83 50 03 00 00 c1 e8 0e 83 f0 01 44 8d 2c 00 41 83 e5 02 <66> 43 83 bc 2d 40 32 00 00 ff 0f 84 f8 02 00 00 49 8b 84 24 c0 00
Oops#1 Part4
<4>[   53.644540] RSP: 0018:ffffc9000366f0d0 EFLAGS: 00010202
<4>[   53.649805] RAX: 0000000000000019 RBX: ffff88810c830800 RCX: 0000000000000000
<4>[   53.656984] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
<4>[   53.664156] RBP: ffffc9000366f190 R08: 0000000000000000 R09: 0000000000000000
<4>[   53.671331] R10: ffff88812a680000 R11: 0000000000000000 R12: ffff888130de6e28
<4>[   53.678507] R13: 0000000000000002 R14: ffff88810c830800 R15: 0000000000000000
<4>[   53.685687] FS:  000073bf21ffe940(0000) GS:ffff8888db397000(0000) knlGS:0000000000000000
<4>[   53.693826] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[   53.699607] CR2: 0000000000003244 CR3: 000000011c7ae003 CR4: 0000000000f72ef0
<4>[   53.706787] PKRU: 55555554
<4>[   53.709520] Call Trace:
<4>[   53.711995]  <TASK>
<4>[   53.714126]  ? check_noncircular+0x7e/0x150
<4>[   53.718350]  ? register_lock_class+0x48/0x4a0
<4>[   53.722740]  ? save_trace+0x54/0x390
<4>[   53.726351]  xe_ggtt_insert_bo+0x1a/0x30 [xe]
<4>[   53.730832]  __xe_bo_create_locked+0x1d4/0x920 [xe]
<4>[   53.735835]  ? lock_acquire+0xc4/0x2f0
<4>[   53.739619]  xe_bo_create_pin_map_at_aligned+0x51/0x1f0 [xe]
<4>[   53.745409]  ? drm_exec_cleanup+0x18e/0x1d0 [drm_exec]
<4>[   53.750587]  xe_bo_create_pin_map_at_novm+0xae/0x140 [xe]
<4>[   53.756105]  ? vgacon_doresize+0x260/0x270
<4>[   53.760235]  xe_managed_bo_create_pin_map+0x3c/0x120 [xe]
<4>[   53.765751]  __xe_sa_bo_manager_init+0x90/0x450 [xe]
<4>[   53.770869]  ? _raw_spin_unlock_irqrestore+0x51/0x80
<4>[   53.775867]  ? __devm_add_action+0x70/0xa0