Results for igt@xe_pm@s2idle-exec-after

Result: Abort 1 Warning(s)

i915_display_info2 igt_runner2 results2.json results2-xe-load.json i915_display_info_post_exec2 boot2 dmesg2

DetailValue
Duration unknown
Hostname 
shard-lnl-4
Igt-Version 
IGT-Version: 2.2-gf21690891 (x86_64) (Linux: 6.18.0-rc7-lgci-xe-xe-4141-c701e79730169fab3+ x86_64)
Out 
Using IGT_SRANDOM=1764046754 for randomisation
Opened device: /dev/dri/card0
Starting subtest: s2idle-exec-after
[cmd] rtcwake: assuming RTC uses UTC ...
[cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Tue Nov 25 04:59:31 2025
Subtest s2idle-exec-after: SUCCESS (1.879s)

This test caused an abort condition: Kernel badly tainted (0x240, 0x200) (check dmesg for details):
	TAINT_WARN: WARN_ON has happened.
Err 
Starting subtest: s2idle-exec-after
Subtest s2idle-exec-after: SUCCESS (1.879s)
Dmesg

Scroll to first warning
<6> [112.459897] Console: switching to colour dummy device 80x25
<6> [112.459982] [IGT] xe_pm: executing
<7> [113.061020] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [113.061137] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [113.061252] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<6> [113.500126] [IGT] xe_pm: starting subtest s2idle-exec-after
<6> [113.598690] PM: suspend entry (s2idle)
<6> [113.603681] Filesystems sync: 0.004 seconds
<6> [113.636342] Freezing user space processes
<4> [113.637413] ------------[ cut here ]------------
<4> [113.637575] WARNING: CPU: 1 PID: 2677 at kernel/freezer.c:139 __set_task_frozen+0x7f/0xb0
<4> [113.637591] Modules linked in: snd_hda_codec_intelhdmi snd_hda_codec_hdmi xe drm_gpuvm drm_gpusvm_helper drm_ttm_helper ttm gpu_sched drm_suballoc_helper drm_exec drm_buddy drm_display_helper cec rc_core drm_kunit_helpers i2c_algo_bit kunit hid_sensor_custom hid_sensor_hub hid_generic intel_ishtp_hid hid intel_uncore_frequency intel_uncore_frequency_common cmdlinepart spi_nor x86_pkg_temp_thermal intel_powerclamp mtd mei_gsc_proxy ucsi_acpi intel_rapl_msr coretemp typec_ucsi wmi_bmof typec kvm_intel kvm irqbypass polyval_clmulni ghash_clmulni_intel aesni_intel snd_hda_intel rapl snd_intel_dspcfg processor_thermal_device_pci processor_thermal_device snd_hda_codec intel_cstate processor_thermal_wt_hint platform_temperature_control snd_hda_core processor_thermal_soc_slider snd_hwdep platform_profile processor_thermal_rfim snd_pcm r8169 processor_thermal_rapl snd_timer snd intel_rapl_common spi_intel_pci soundcore spi_intel realtek idma64 processor_thermal_wt_req intel_ish_ipc mei_me processor_thermal_power_floor
<4> [113.637911] intel_ishtp mei intel_vpu thunderbolt processor_thermal_mbox video binfmt_misc intel_skl_int3472_tps68470 intel_pmc_core tps68470_regulator pmt_telemetry clk_tps68470 int3403_thermal int340x_thermal_zone pmt_discovery pmt_class wmi intel_hid intel_pmc_ssram_telemetry int3400_thermal intel_skl_int3472_discrete sparse_keymap acpi_thermal_rel acpi_pad intel_vsec pinctrl_intel_platform intel_skl_int3472_common acpi_tad nls_iso8859_1 dm_multipath msr nvme_fabrics fuse efi_pstore nfnetlink autofs4
<4> [113.637985] CPU: 1 UID: 0 PID: 2677 Comm: rtcwake Tainted: G U 6.18.0-rc7-lgci-xe-xe-4141-c701e79730169fab3+ #1 PREEMPT(voluntary)
<4> [113.637992] Tainted: [U]=USER
<4> [113.637994] Hardware name: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D99.2508051732 08/05/2025
<4> [113.637998] RIP: 0010:__set_task_frozen+0x7f/0xb0
<4> [113.638006] Code: c4 00 20 00 00 74 06 41 f6 c4 03 74 40 41 81 e4 00 40 00 00 75 16 8b 15 23 ba 47 02 85 d2 74 0c 8b 83 30 0f 00 00 85 c0 74 02 <0f> 0b 8b 43 18 c7 43 18 00 80 00 00 89 43 1c b8 00 80 00 00 5b 41
<4> [113.638009] RSP: 0018:ffffc9000be37bd0 EFLAGS: 00010002
<4> [113.638015] RAX: 0000000000000002 RBX: ffff88812f2fb4c0 RCX: 0000000000000000
<4> [113.638019] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000
<4> [113.638021] RBP: ffffc9000be37be0 R08: 0000000000000000 R09: 0000000000000000
<4> [113.638024] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
<4> [113.638027] R13: 0000000000000000 R14: ffff88812f2fc310 R15: ffff88812f2fb4c0
<4> [113.638030] FS: 000071be5b885740(0000) GS:ffff8888db36a000(0000) knlGS:0000000000000000
<4> [113.638033] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [113.638037] CR2: 00005f9401c1c8b4 CR3: 000000014dece005 CR4: 0000000000f72ef0
<4> [113.638040] PKRU: 55555554
<4> [113.638043] Call Trace:
<4> [113.638045] <TASK>
<4> [113.638049] ? __pfx___set_task_frozen+0x10/0x10
<4> [113.638056] task_call_func+0x6d/0x120
<4> [113.638065] ? cgroup_freezing+0x89/0x200
<4> [113.638077] freeze_task+0x98/0x100
<4> [113.638087] try_to_freeze_tasks+0xd2/0x440
<4> [113.638102] freeze_processes+0x56/0xd0
<4> [113.638108] pm_suspend+0x209/0x7f0
<4> [113.638118] state_store+0x6e/0xe0
<4> [113.638127] kobj_attr_store+0x12/0x40
<4> [113.638136] sysfs_kf_write+0x4d/0x80
<4> [113.638147] kernfs_fop_write_iter+0x188/0x240
<4> [113.638160] vfs_write+0x283/0x540
<4> [113.638181] ksys_write+0x6f/0xf0
<4> [113.638191] __x64_sys_write+0x19/0x30
<4> [113.638195] x64_sys_call+0x79/0x26a0
<4> [113.638202] do_syscall_64+0x93/0xd30
<4> [113.638209] ? irqentry_exit_to_user_mode+0xf4/0x320
<4> [113.638219] ? irqentry_exit+0x77/0xb0
<4> [113.638225] ? exc_page_fault+0xbd/0x2c0
<4> [113.638235] entry_SYSCALL_64_after_hwframe+0x76/0x7e
<4> [113.638240] RIP: 0033:0x71be5b71c574
<4> [113.638246] Code: c7 00 16 00 00 00 b8 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 80 3d d5 ea 0e 00 00 74 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 55 48 89 e5 48 83 ec 20 48 89
<4> [113.638250] RSP: 002b:00007ffc6fcf6858 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
<4> [113.638255] RAX: ffffffffffffffda RBX: 0000000000000007 RCX: 000071be5b71c574
<4> [113.638258] RDX: 0000000000000007 RSI: 000056f76f41f4a0 RDI: 000000000000000b
<4> [113.638260] RBP: 00007ffc6fcf6880 R08: 000071be5b803b20 R09: 0000000000000000
<4> [113.638263] R10: 0000000000000001 R11: 0000000000000202 R12: 0000000000000007
<4> [113.638266] R13: 000056f76f41f4a0 R14: 000056f76f41d450 R15: 000071be5b801ee0
<4> [113.638290] </TASK>
<4> [113.638292] irq event stamp: 9954
<4> [113.638295] hardirqs last enabled at (9953): [<ffffffff828c8671>] _raw_spin_unlock_irqrestore+0x51/0x80
<4> [113.638306] hardirqs last disabled at (9954): [<ffffffff828c82f4>] _raw_spin_lock_irqsave+0x74/0x80
<4> [113.638311] softirqs last enabled at (9326): [<ffffffff8133e793>] kernel_fpu_end+0x53/0x70
<4> [113.638318] softirqs last disabled at (9324): [<ffffffff8133efb4>] kernel_fpu_begin_mask+0xc4/0x120
<4> [113.638324] ---[ end trace 0000000000000000 ]---
<6> [113.640116] Freezing user space processes completed (elapsed 0.003 seconds)
<6> [113.640197] OOM killer disabled.
<6> [113.640202] Freezing remaining freezable tasks
<6> [113.641716] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<7> [113.712887] GFP mask restricted
<6> [113.732499] r8169 0000:7f:00.0 enp127s0: Link is Down
<7> [113.768145] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [113.769073] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010
<7> [113.784455] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [113.787780] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [113.790112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [113.790768] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [113.791303] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B
<7> [113.792485] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C
<7> [113.792969] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D
<7> [113.793431] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
<7> [113.794401] xe 0000:00:02.0: [drm:drm_client_dev_suspend] fbdev: ret=0
<7> [113.795893] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [113.796391] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [113.796878] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [113.797333] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [113.797758] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [113.798161] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [113.798595] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [113.798964] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [113.799308] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [113.799621] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [113.799947] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [113.800237] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [113.800544] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [113.800839] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [113.801094] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [113.801347] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [113.801602] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [113.801864] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [113.802090] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [113.802322] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [113.802558] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [113.802774] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [113.802970] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [113.803166] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [113.803354] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [113.803535] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [113.803706] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [113.803890] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [113.804052] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [113.804212] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [113.804369] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [113.804521] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [113.804667] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [113.804824] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [113.804968] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [113.805104] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [113.805260] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [113.805399] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [113.805525] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] fastset requirement not met, forcing full modeset
<7> [113.805652] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:88:pipe A] releasing DPLL 0
<7> [113.805848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [113.805975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:88:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [113.806129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [113.806241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [113.806341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [113.806434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.806524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.806612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [113.806726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:88:pipe A] data rate 0 num active planes 0
<7> [113.806861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [113.806980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [113.807097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.807208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [113.807319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [113.807426] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:88:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [113.807558] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [113.807675] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [113.807797] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [113.807896] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [113.808014] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: no [modeset]
<7> [113.808109] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [113.808205] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [113.808303] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [113.808393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [113.808478] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [113.808560] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [113.808751] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [113.809718] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [113.809831] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [114.013060] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 0
<7> [114.014805] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [114.036185] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [114.036910] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power off
<7> [114.037407] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [114.037844] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [114.089828] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [114.095176] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [114.095919] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:88:pipe A]
<7> [114.096053] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A]
<7> [114.096685] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A]
<7> [114.097493] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [114.098120] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [114.099653] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:207:DDI A/PHY A]
<7> [114.100082] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:216:DDI TC1/PHY TC1]
<7> [114.100508] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:218:DP-MST A]
<7> [114.100933] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST B]
<7> [114.101340] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST C]
<7> [114.101778] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:228:DDI TC2/PHY TC2]
<7> [114.102163] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:230:DP-MST A]
<7> [114.102591] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DP-MST B]
<7> [114.103022] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:232:DP-MST C]
<7> [114.103392] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:236:DDI TC3/PHY TC3]
<7> [114.103778] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:238:DP-MST A]
<7> [114.104151] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DP-MST B]
<7> [114.104581] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:240:DP-MST C]
<7> [114.105008] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:208:eDP-1]
<7> [114.105618] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [114.105994] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [114.106313] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [114.106983] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:88:pipe A]
<7> [114.107500] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.108036] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [114.108423] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [114.108840] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800010 0x9a00071)
<7> [114.113386] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC
<7> [114.113638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D
<7> [114.113910] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [114.114141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [114.114357] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C
<7> [114.114559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [114.114759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [114.114949] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [114.115125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [114.115319] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [114.115578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [114.115791] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x0
<7> [114.116047] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 0 (mbus joined: no)
<7> [114.116179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_1
<7> [114.116340] xe 0000:00:02.0: [drm:bxt_enable_dc9 [xe]] Enabling DC9
<7> [114.116473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 08
<7> [114.128454] PM: suspend of devices complete after 415.547 msecs
<7> [114.128477] PM: start suspend of devices complete after 486.593 msecs
<7> [114.145885] PM: late suspend of devices complete after 17.396 msecs
<6> [114.168960] ACPI: EC: interrupt blocked
<7> [114.387309] PM: noirq suspend of devices complete after 238.658 msecs
<6> [114.387379] ACPI: \_SB_.PR00: LPI: Device not power manageable
<6> [114.387397] ACPI: \_SB_.PR01: LPI: Device not power manageable
<6> [114.387404] ACPI: \_SB_.PR02: LPI: Device not power manageable
<6> [114.387411] ACPI: \_SB_.PR03: LPI: Device not power manageable
<6> [114.387417] ACPI: \_SB_.PR04: LPI: Device not power manageable
<6> [114.387423] ACPI: \_SB_.PR05: LPI: Device not power manageable
<6> [114.387429] ACPI: \_SB_.PR06: LPI: Device not power manageable
<6> [114.387435] ACPI: \_SB_.PR07: LPI: Device not power manageable
<6> [114.387449] ACPI: \_SB_.PC00.IPU0: LPI: Device not power manageable
<6> [114.387455] ACPI: \_SB_.PC00.NPU0: LPI: Device not power manageable
<6> [114.387462] ACPI: \_SB_.PC00.HECI: LPI: Device not power manageable
<6> [114.387483] ACPI: \_SB_.PC00.ISHD: LPI: Device not power manageable
<6> [114.387491] ACPI: \_SB_.PC00.TRP0: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [114.387498] ACPI: \_SB_.PC00.TRP1: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [114.387504] ACPI: \_SB_.PC00.TRP2: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [114.389400] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<6> [114.397860] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 ms entry
<7> [114.403299] PM: Triggering wakeup from IRQ 9
<6> [114.412536] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [114.412551] PM: suspend-to-idle
<7> [114.412833] ACPI: EC: ACPI EC GPE status set
<7> [114.412880] ACPI: PM: Rearming ACPI SCI for wakeup
<7> [128.635312] Timekeeping suspended for 14.417 seconds
<7> [128.635417] PM: Triggering wakeup from IRQ 9
<7> [128.637104] ACPI: PM: ACPI fixed event wakeup
<7> [128.637127] PM: resume from suspend-to-idle
<6> [128.670925] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [128.677872] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 ms exit
<6> [128.678890] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [128.679634] ACPI: EC: interrupt unblocked
<7> [129.100102] PM: noirq resume of devices complete after 421.206 msecs
<6> [129.111800] pci 0000:00:05.0: Setting to D3hot
<7> [129.127544] PM: early resume of devices complete after 24.795 msecs
<7> [129.129034] xe 0000:00:02.0: [drm:gen9_sanitize_dc_state [xe]] Resetting DC state tracking from 08 to 08
<7> [129.129593] xe 0000:00:02.0: [drm:bxt_disable_dc9 [xe]] Disabling DC9
<7> [129.132794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 08 to 00
<7> [129.133611] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00
<7> [129.134090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_1
<7> [129.134615] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [129.135022] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Sanitizing cdclk programmed by pre-os
<7> [129.135472] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [129.135898] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [129.136436] xe 0000:00:02.0: [drm:icl_display_core_init [xe]] Unknown memory configuration; disabling address buddy logic.
<7> [129.148135] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [129.148366] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [129.148583] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00
<7> [129.148841] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [129.149093] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [129.149332] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B
<7> [129.149555] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C
<7> [129.149770] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D
<7> [129.150023] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC
<6> [129.191113] nvme nvme0: 8/0/0 default/read/poll queues
<7> [129.193115] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [129.193329] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [129.193475] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [129.193588] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected)
<7> [129.193684] xe 0000:00:02.0: [drm:intel_cdclk_read_hw [xe]] Current CDCLK 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [129.193882] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] hw state readout: disabled
<7> [129.193980] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] hw state readout: disabled
<7> [129.194081] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] hw state readout: disabled
<7> [129.194158] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] hw state readout: disabled, pipe A
<7> [129.194234] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A
<7> [129.194309] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A
<7> [129.194378] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A
<7> [129.194445] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A
<7> [129.194511] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] hw state readout: disabled, pipe A
<7> [129.194576] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] hw state readout: disabled, pipe B
<7> [129.194641] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] hw state readout: disabled, pipe B
<7> [129.194706] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] hw state readout: disabled, pipe B
<7> [129.194770] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] hw state readout: disabled, pipe B
<7> [129.194834] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] hw state readout: disabled, pipe B
<7> [129.194901] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] hw state readout: disabled, pipe B
<7> [129.194966] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] hw state readout: disabled, pipe C
<7> [129.195035] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] hw state readout: disabled, pipe C
<7> [129.195105] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] hw state readout: disabled, pipe C
<7> [129.195174] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] hw state readout: disabled, pipe C
<7> [129.195244] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] hw state readout: disabled, pipe C
<7> [129.195313] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] hw state readout: disabled, pipe C
<7> [129.195375] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:207:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [129.195449] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [129.195510] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:216:DDI TC1/PHY TC1] hw state readout: disabled, pipe A
<7> [129.195570] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:218:DP-MST A] hw state readout: disabled, pipe A
<7> [129.195628] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:219:DP-MST B] hw state readout: disabled, pipe B
<7> [129.195686] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:220:DP-MST C] hw state readout: disabled, pipe C
<7> [129.195745] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [129.195804] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:228:DDI TC2/PHY TC2] hw state readout: disabled, pipe A
<7> [129.195865] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:230:DP-MST A] hw state readout: disabled, pipe A
<7> [129.195925] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:231:DP-MST B] hw state readout: disabled, pipe B
<7> [129.195986] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:232:DP-MST C] hw state readout: disabled, pipe C
<7> [129.196056] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4
<7> [129.196119] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:236:DDI TC3/PHY TC3] hw state readout: disabled, pipe A
<7> [129.196183] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:238:DP-MST A] hw state readout: disabled, pipe A
<7> [129.196246] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:239:DP-MST B] hw state readout: disabled, pipe B
<7> [129.196314] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:240:DP-MST C] hw state readout: disabled, pipe C
<7> [129.196377] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [129.196449] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [129.196523] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TBT PLL hw state readout: pipe_mask 0x0, on 1
<7> [129.196602] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [129.196680] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [129.196756] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [129.196828] xe 0000:00:02.0: [drm:intel_dpll_readout_hw_state [xe]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [129.196913] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:208:eDP-1] hw state readout: disabled
<7> [129.196982] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:217:DP-1] hw state readout: disabled
<7> [129.197056] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:229:DP-2] hw state readout: disabled
<7> [129.197127] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:237:DP-3] hw state readout: disabled
<7> [129.197193] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] min_cdclk 0 kHz
<7> [129.197258] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] min_cdclk 0 kHz
<7> [129.197322] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] min_cdclk 0 kHz
<7> [129.197385] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] min_cdclk 0 kHz
<7> [129.197448] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] min_cdclk 0 kHz
<7> [129.197511] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] min_cdclk 0 kHz
<7> [129.197571] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] min_cdclk 0 kHz
<7> [129.197632] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] min_cdclk 0 kHz
<7> [129.197693] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] min_cdclk 0 kHz
<7> [129.197751] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] min_cdclk 0 kHz
<7> [129.197809] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] min_cdclk 0 kHz
<7> [129.197866] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] min_cdclk 0 kHz
<7> [129.197923] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] min_cdclk 0 kHz
<7> [129.197979] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] min_cdclk 0 kHz
<7> [129.198043] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] min_cdclk 0 kHz
<7> [129.198104] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] min_cdclk 0 kHz
<7> [129.198159] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] min_cdclk 0 kHz
<7> [129.198214] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] min_cdclk 0 kHz
<7> [129.198270] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] min_cdclk 0 kHz
<7> [129.198328] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] min_cdclk 0 kHz
<7> [129.198386] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] min_cdclk 0 kHz
<7> [129.198449] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:88:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [129.198505] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:146:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [129.198559] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:204:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [129.198614] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 0 num active planes 0
<7> [129.198696] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0
<7> [129.198778] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0
<7> [129.198879] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: disabled, CMTG B: disabled, Transcoder A secondary: no, Transcoder B secondary: no
<7> [129.198993] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: no [setup_hw_state]
<7> [129.199084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [setup_hw_state]
<7> [129.199170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [setup_hw_state]
<7> [129.199253] xe 0000:00:02.0: [drm:intel_dpll_sanitize_state [xe]] TBT PLL enabled but not in use, disabling
<7> [129.199397] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:208:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [129.199491] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:207:DDI A/PHY A][CRTC:88:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000
<7> [129.199571] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [129.199663] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [129.199760] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:207:DDI A/PHY A] [CRTC:88:pipe A]
<7> [129.199849] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [129.199938] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [129.200034] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [129.200114] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [129.200192] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [129.200268] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [129.200344] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [129.200420] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [129.200496] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [129.200571] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [129.200647] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [129.200721] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [129.200796] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [129.200870] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [129.200944] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [129.201024] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [129.201102] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [129.201179] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [129.201253] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [129.201328] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [129.201401] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [129.201473] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [129.201545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [129.201617] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [129.201689] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [129.201760] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [129.201830] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [129.201901] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [129.201971] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [129.202047] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [129.202121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [129.202191] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [129.202264] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in intel_dpll (expected 0000000000000000, found ffff88815432b2f0)
<7> [129.202339] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dpll_hw_state
<7> [129.202411] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [129.202484] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [129.202558] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [129.202630] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [129.202702] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [129.202773] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [129.202843] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [129.202913] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [129.202983] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [129.203060] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [129.203133] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [129.203202] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [129.203271] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [129.203339] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [129.203408] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [129.203477] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [129.203545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [129.203616] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [129.203689] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [129.203761] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [129.203833] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [129.203906] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [129.203976] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [129.204054] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [129.204133] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [129.204207] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [129.204275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [129.204344] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [129.204414] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [129.204484] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [129.204553] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [129.204622] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [129.204692] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] fastset requirement not met, forcing full modeset
<7> [129.204763] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:146:pipe B] fastset requirement not met in dpll_hw_state
<7> [129.204831] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [129.204899] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [129.204968] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [129.205044] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [129.205115] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [129.205184] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [129.205250] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [129.205317] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [129.205385] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [129.205452] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [129.205519] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [129.205588] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [129.205659] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [129.205729] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [129.205799] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [129.205868] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [129.205936] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [129.206007] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [129.206089] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [129.206163] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [129.206232] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [129.206301] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [129.206369] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [129.206437] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [129.206506] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [129.206574] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [129.206643] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [129.206711] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [129.206779] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:146:pipe B] fastset requirement not met, forcing full modeset
<7> [129.206848] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:204:pipe C] fastset requirement not met in dpll_hw_state
<7> [129.206916] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected:
<7> [129.206982] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 0, ssc_enabled: no, use_c10: no, tbt_mode: no
<7> [129.207060] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c20pll_hw_state: clock: 0
<7> [129.207135] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx[0] = 0x0000, tx[1] = 0x0000, tx[2] = 0x0000
<7> [129.207208] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cmn[0] = 0x0000, cmn[1] = 0x0000, cmn[2] = 0x0000, cmn[3] = 0x0000
<7> [129.207279] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[0] = 0x0000
<7> [129.207349] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[1] = 0x0000
<7> [129.207420] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[2] = 0x0000
<7> [129.207490] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[3] = 0x0000
<7> [129.207559] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[4] = 0x0000
<7> [129.207629] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[5] = 0x0000
<7> [129.207698] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[6] = 0x0000
<7> [129.207766] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[7] = 0x0000
<7> [129.207835] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[8] = 0x0000
<7> [129.207904] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mplla[9] = 0x0000
<7> [129.207973] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] mpllb[10] = 0x0000
<7> [129.208051] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] vdr: custom width: 0x00, serdes rate: 0x00, hdmi rate: 0x00
<7> [129.208122] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found:
<7> [129.208193] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [129.208262] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [129.208331] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] multiplier: 225, tx_clk_div: 1.
<7> [129.208400] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] c10pll_rawhw_state:
<7> [129.208471] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] tx: 0x10, cmn: 0x21
<7> [129.208542] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [129.208614] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [129.208684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [129.208754] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [129.208825] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [129.208896] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:204:pipe C] fastset requirement not met, forcing full modeset
<7> [129.209027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [129.209095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:88:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [129.209169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [129.209235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [129.209299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [129.209355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [129.209411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [129.209467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [129.209553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:88:pipe A] data rate 1390840 num active planes 1
<7> [129.209649] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [129.209740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [129.209827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [129.209904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [129.209980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [129.210068] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:88:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [129.210175] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [129.210251] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [129.210325] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [129.210398] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [129.210489] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:88:pipe A] allocated DPLL 0
<7> [129.210564] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:88:pipe A] reserving DPLL 0
<7> [129.210642] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [modeset]
<7> [129.210719] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [129.210793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [129.210868] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [129.210941] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [129.211019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [129.211096] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [129.211178] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [129.211255] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [129.211332] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [129.211407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [129.211479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [129.211551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [129.211622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [129.211693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [129.211764] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [129.211834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [129.211904] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [129.211974] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [129.212053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [129.212127] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [129.212199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [129.212270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [129.212341] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [129.212412] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [129.212483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [129.212553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [129.212623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [129.212693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [129.212762] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [129.212832] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [129.212901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [129.212970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [129.213056] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [129.213132] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [129.213204] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [129.213275] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [129.213345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [129.213416] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [129.213485] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [129.213554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [129.213623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [129.213692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [129.213761] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [129.213830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [129.213898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [129.213965] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [129.214041] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214247] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [129.214315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [129.214387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214458] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [129.214599] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [129.214668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [129.214737] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:209] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [129.214806] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [129.214874] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [129.214944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [129.215016] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [129.215085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [129.215157] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [129.215226] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [129.215295] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [modeset]
<7> [129.215363] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:91:plane 1B] fb: [NOFB], visible: no
<7> [129.215431] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:101:plane 2B] fb: [NOFB], visible: no
<7> [129.215499] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:111:plane 3B] fb: [NOFB], visible: no
<7> [129.215567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:121:plane 4B] fb: [NOFB], visible: no
<7> [129.215634] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:131:plane 5B] fb: [NOFB], visible: no
<7> [129.215701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:141:cursor B] fb: [NOFB], visible: no
<7> [129.215768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [modeset]
<7> [129.215836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:149:plane 1C] fb: [NOFB], visible: no
<7> [129.215903] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:159:plane 2C] fb: [NOFB], visible: no
<7> [129.215972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:169:plane 3C] fb: [NOFB], visible: no
<7> [129.216050] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:179:plane 4C] fb: [NOFB], visible: no
<7> [129.216123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:189:plane 5C] fb: [NOFB], visible: no
<7> [129.216195] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:199:cursor C] fb: [NOFB], visible: no
<7> [129.216350] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072)
<7> [129.216641] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [129.216743] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [129.216821] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [129.216898] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:207:DDI A/PHY A]
<7> [129.216964] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:216:DDI TC1/PHY TC1]
<7> [129.217037] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:218:DP-MST A]
<7> [129.217103] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST B]
<7> [129.217169] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST C]
<7> [129.217232] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:228:DDI TC2/PHY TC2]
<7> [129.217297] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:230:DP-MST A]
<7> [129.217361] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DP-MST B]
<7> [129.217425] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:232:DP-MST C]
<7> [129.217488] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:236:DDI TC3/PHY TC3]
<7> [129.217550] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:238:DP-MST A]
<7> [129.217610] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DP-MST B]
<7> [129.217670] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:240:DP-MST C]
<7> [129.217728] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:217:DP-1]
<7> [129.217791] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:229:DP-2]
<7> [129.217853] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:237:DP-3]
<7> [129.217933] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [129.218079] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [129.218143] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [129.218241] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [129.219022] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:88:pipe A]
<7> [129.219101] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [129.220689] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power on
<7> [129.220762] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [129.220857] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [129.230140] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [129.230239] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power on
<7> [129.230346] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [129.266502] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [129.266720] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [129.266946] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A]
<6> [129.317421] r8169 0000:7f:00.0 enp127s0: Link is Down
<7> [129.440186] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [129.440699] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on
<7> [129.441106] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [129.444088] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [129.445407] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [129.446329] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [129.447576] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [129.448799] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [129.449929] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Clock recovery OK
<7> [129.450357] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [129.451778] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [129.452168] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [129.453086] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [129.453631] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [129.453990] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [129.454441] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 4518
<7> [129.470609] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [129.472250] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:208:eDP-1]
<7> [129.472557] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:88:pipe A]
<7> [129.475012] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:146:pipe B]
<7> [129.475476] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:204:pipe C]
<7> [129.477827] xe 0000:00:02.0: [drm:intel_opregion_resume [xe]] 4 outputs detected
<7> [129.478159] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1]
<7> [129.478585] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.478890] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2]
<7> [129.479279] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.479556] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3]
<7> [129.479876] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.484089] xe 0000:00:02.0: [drm:drm_client_dev_resume] fbdev: ret=0
<7> [129.484101] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC
<7> [129.484303] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D
<7> [129.484517] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C
<7> [129.484717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [129.484905] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [129.485087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [129.485264] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [129.485417] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [129.485787] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2
<7> [129.486047] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010
<7> [129.498054] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2
<7> [129.498804] PM: resume of devices complete after 371.235 msecs
<7> [129.499384] GFP mask restored
<6> [129.512629] OOM killer enabled.
<6> [129.512635] Restarting tasks: Starting
<6> [129.515192] mei_gsc_proxy 0000:00:16.0-0f73db04-97ab-4125-b893-e904ad0d5464: bound 0000:00:02.0 (ops xe_gsc_proxy_component_ops [xe])
<6> [129.517583] Restarting tasks: Done
<6> [129.526954] efivarfs: resyncing variable state
<6> [129.550965] efivarfs: finished resyncing variable state
<5> [129.551121] random: crng reseeded on system resumption
<6> [129.563837] PM: suspend exit
<6> [129.600951] [IGT] xe_pm: finished subtest s2idle-exec-after, SUCCESS
<7> [129.602413] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [129.602582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [129.603633] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [129.603770] [IGT] xe_pm: exiting, ret=0
<6> [129.620483] Console: switching to colour frame buffer device 180x56
<7> [129.654062] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [129.654240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [129.654363] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2025-11-25 05:34:35