Results for igt@kms_invalid_dotclock

Result: skip

git-log-oneline igt_runner17 run17 boot17 dmesg17 runtimes17

DetailValue
Time1.46 seconds
Igt-Version
IGT-Version: 1.24-g19115648 (x86_64) (Linux: 5.3.0-rc7-gd3d45e02f5ad-drmtip_362+ x86_64)
Out
IGT-Version: 1.24-g19115648 (x86_64) (Linux: 5.3.0-rc7-gd3d45e02f5ad-drmtip_362+ x86_64)
Max dotclock: 1305600 kHz
Test requirement not met in function test, file ../tests/kms_invalid_dotclock.c:104:
Test requirement: valid_connectors
No suitable connectors found
SKIP (0.310s)
Dmesg
<6> [824.453398] Console: switching to colour dummy device 80x25
<6> [824.453437] [IGT] kms_invalid_dotclock: executing
<7> [824.628104] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:250:DP-1]
<7> [824.628175] [drm:intel_dp_detect [i915]] [CONNECTOR:250:DP-1]
<7> [824.628217] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:250:DP-1] disconnected
<7> [824.628688] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-1]
<7> [824.628765] [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-1]
<7> [824.628825] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-1] disconnected
<7> [824.629455] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:244:eDP-1]
<7> [824.629506] [drm:intel_dp_detect [i915]] [CONNECTOR:244:eDP-1]
<7> [824.629578] [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [824.629648] [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [824.629713] [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [824.629792] [drm:intel_power_well_enable [i915]] enabling DC off
<7> [824.629844] [drm:gen9_set_dc_state [i915]] Setting DC state from 02 to 00
<7> [824.629935] [drm:intel_combo_phy_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [824.630001] [drm:intel_combo_phy_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [824.630083] [drm:edp_panel_vdd_on [i915]] Turning [ENCODER:243:DDI A] VDD on
<7> [824.630234] [drm:edp_panel_vdd_on [i915]] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [824.630739] [drm:intel_dp_detect [i915]] [ENCODER:243:DDI A] MST support? port: no, sink: no, modparam: yes
<7> [824.631199] [drm:drm_add_display_info] non_desktop set to 0
<7> [824.631213] [drm:drm_add_edid_modes] ELD: no CEA Extension found
<7> [824.631215] [drm:drm_add_display_info] non_desktop set to 0
<7> [824.631242] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:244:eDP-1] probed modes :
<7> [824.631246] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [824.631249] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [824.631265] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:250:DP-1]
<7> [824.631299] [drm:intel_dp_detect [i915]] [CONNECTOR:250:DP-1]
<7> [824.631327] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:250:DP-1] disconnected
<7> [824.631338] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-1]
<7> [824.631376] [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-1]
<7> [824.631406] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-1] disconnected
<7> [824.631428] [drm:drm_mode_setcrtc] [CRTC:83:pipe A]
<7> [824.631598] [drm:intel_atomic_check [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz
<7> [824.631644] [drm:intel_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [824.631716] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb (   0 -  969) -> (   0 -    0), size  969 ->    0
<7> [824.631737] [drm:skl_compute_wm [i915]] [PLANE:80:cursor A] ddb ( 969 - 1024) -> (   0 -    0), size   55 ->    0
<7> [824.631758] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm
<7> [824.631778] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   lines    1,   7,   8,   9,  12,  14,  14,  16,   0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0
<7> [824.631798] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]  blocks   19, 183, 209, 235, 313, 365, 365, 417,  33 ->    0,   0,   0,   0,   0,   0,   0,   0,   0
<7> [824.631818] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb   22, 203, 231, 260, 346, 403, 403, 460,   0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0
<7> [824.631861] [drm:intel_bw_atomic_check [i915]] pipe A data rate 0 num active planes 0
<7> [824.631894] [drm:intel_dump_pipe_config [i915]] [CRTC:83:pipe A] enable: no [modeset]
<7> [824.631925] [drm:intel_dump_pipe_config [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [824.631958] [drm:intel_dump_pipe_config [i915]] [PLANE:38:plane 2A] fb: [NOFB], visible: no
<7> [824.631985] [drm:intel_dump_pipe_config [i915]] [PLANE:45:plane 3A] fb: [NOFB], visible: no
<7> [824.632015] [drm:intel_dump_pipe_config [i915]] [PLANE:52:plane 4A] fb: [NOFB], visible: no
<7> [824.632044] [drm:intel_dump_pipe_config [i915]] [PLANE:59:plane 5A] fb: [NOFB], visible: no
<7> [824.632075] [drm:intel_dump_pipe_config [i915]] [PLANE:66:plane 6A] fb: [NOFB], visible: no
<7> [824.632103] [drm:intel_dump_pipe_config [i915]] [PLANE:73:plane 7A] fb: [NOFB], visible: no
<7> [824.632131] [drm:intel_dump_pipe_config [i915]] [PLANE:80:cursor A] fb: [NOFB], visible: no
<7> [824.639943] [drm:intel_edp_backlight_off [i915]] 
<7> [824.841675] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 0
<7> [824.841874] [drm:intel_disable_pipe [i915]] disabling pipe A
<7> [824.855537] [drm:intel_edp_panel_off.part.35 [i915]] Turn [ENCODER:243:DDI A] panel power off
<7> [824.855738] [drm:intel_edp_panel_off.part.35 [i915]] Wait for panel power off time
<7> [824.855924] [drm:wait_panel_status [i915]] mask b0000000 value 00000000 status a0000002 control 00000060
<7> [824.859770] [drm:gen8_de_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [824.859865] [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:243:DDI A] - long
<7> [824.859956] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [824.860102] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:243:DDI A]
<7> [824.880116] [drm:gen8_de_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [824.880201] [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:243:DDI A] - long
<7> [824.880282] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [824.880399] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:243:DDI A]
<7> [824.910818] [drm:wait_panel_status [i915]] Wait complete
<7> [824.910928] [drm:intel_power_well_disable [i915]] disabling DDI A IO
<7> [824.911042] [drm:intel_power_well_disable [i915]] disabling AUX A
<7> [824.911148] [drm:__intel_fbc_disable [i915]] Disabling FBC on pipe A
<7> [824.911236] [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 1, on? 1) for crtc 83
<7> [824.911339] [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [824.911449] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [824.911628] [drm:gen8_de_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [824.911732] [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:243:DDI A] - long
<7> [824.911831] [drm:intel_atomic_commit_tail [i915]] [ENCODER:243:DDI A]
<7> [824.911923] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30
<7> [824.912009] [drm:intel_atomic_commit_tail [i915]] [ENCODER:249:DDI B]
<7> [824.912120] [drm:intel_atomic_commit_tail [i915]] [ENCODER:251:DP-MST A]
<7> [824.912254] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:243:DDI A]
<7> [824.912374] [drm:intel_atomic_commit_tail [i915]] [ENCODER:252:DP-MST B]
<7> [824.912471] [drm:intel_atomic_commit_tail [i915]] [ENCODER:253:DP-MST C]
<7> [824.912586] [drm:intel_atomic_commit_tail [i915]] [ENCODER:254:DP-MST D]
<7> [824.912749] [drm:verify_connector_state [i915]] [CONNECTOR:244:eDP-1]
<7> [824.912847] [drm:verify_single_dpll_state.isra.112 [i915]] DPLL 0
<7> [824.912934] [drm:verify_single_dpll_state.isra.112 [i915]] DPLL 1
<7> [824.913027] [drm:verify_single_dpll_state.isra.112 [i915]] TBT PLL
<7> [824.913166] [drm:intel_atomic_commit_tail [i915]] [CRTC:83:pipe A]
<7> [824.913423] [drm:intel_power_well_disable [i915]] disabling DC off
<7> [824.913527] [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [824.913679] [drm:gen9_set_dc_state [i915]] Setting DC state from 00 to 02
<7> [824.914854] [drm:intel_power_well_disable [i915]] disabling always-on
<7> [824.915031] i915 Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   i915_gem_fault+0xe2/0x8e0 [i915]
   __do_fault+0x2c/0xb0
   __handle_mm_fault+0x8f1/0xfa0
   handle_mm_fault+0x155/0x360
   __do_page_fault+0x249/0x4f0
   page_fault+0x34/0x40
<7> [824.915353] i915 Wakeref last released:
   __untrack_all_wakerefs+0x67/0x70 [i915]
   __intel_wakeref_dec_and_check_tracking+0x61/0x80 [i915]
   __intel_runtime_pm_put+0x11a/0x260 [i915]
   i915_gem_object_set_tiling+0x28e/0x630 [i915]
   i915_gem_set_tiling_ioctl+0x22a/0x2a0 [i915]
   drm_ioctl_kernel+0x83/0xf0
   drm_ioctl+0x2f3/0x3b0
   do_vfs_ioctl+0xa0/0x6f0
<7> [824.915358] i915 Wakeref count: 8
<7> [824.915932] i915 Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   intel_display_power_get+0x1f/0x60 [i915]
   edp_panel_vdd_on+0xd5/0x210 [i915]
   intel_dp_aux_xfer+0xeb/0x920 [i915]
   intel_dp_aux_transfer+0xa7/0x200 [i915]
   drm_dp_dpcd_access+0x76/0x110
   drm_dp_dpcd_read+0x29/0xc0
   intel_dp_sink_can_mst.part.7+0x2f/0x60 [i915]
<7> [824.916319] i915 Wakeref x4 taken at:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   intel_display_power_get+0x1f/0x60 [i915]
   modeset_get_crtc_power_domains+0x120/0x140 [i915]
   intel_atomic_commit_tail+0xcf/0x1570 [i915]
   intel_atomic_commit+0x273/0x2f0 [i915]
   drm_atomic_helper_set_config+0x61/0x90
   drm_mode_setcrtc+0x199/0x710
   drm_ioctl_kernel+0x83/0xf0
<7> [824.916558] i915 Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   intel_display_power_get+0x1f/0x60 [i915]
   intel_ddi_pre_pll_enable+0x6e/0x120 [i915]
   intel_encoders_pre_pll_enable.isra.21+0x61/0x80 [i915]
   haswell_crtc_enable+0x5c/0x760 [i915]
   intel_update_crtc+0x52/0x3c0 [i915]
   skl_commit_modeset_enables+0x267/0x2b0 [i915]
   intel_atomic_commit_tail+0x26b/0x1570 [i915]
<7> [824.916778] i915 Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   intel_display_power_get+0x1f/0x60 [i915]
   intel_ddi_pre_enable+0x531/0xd20 [i915]
   intel_encoders_pre_enable.isra.22+0x61/0x80 [i915]
   haswell_crtc_enable+0x82/0x760 [i915]
   intel_update_crtc+0x52/0x3c0 [i915]
   skl_commit_modeset_enables+0x267/0x2b0 [i915]
   intel_atomic_commit_tail+0x26b/0x1570 [i915]
<7> [824.916930] i915 Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x14/0x90 [i915]
   intel_display_power_get+0x1f/0x60 [i915]
   edp_panel_vdd_on+0xd5/0x210 [i915]
   intel_dp_aux_xfer+0xeb/0x920 [i915]
   intel_dp_aux_transfer+0x124/0x200 [i915]
   drm_dp_dpcd_access+0x76/0x110
   drm_dp_dpcd_write+0x21/0x90
   intel_dp_sink_dpms+0x4f/0x100 [i915]
<7> [824.917012] [drm:drm_mode_setcrtc] [CRTC:136:pipe B]
<7> [824.917116] [drm:drm_mode_setcrtc] [CRTC:189:pipe C]
<7> [824.917197] [drm:drm_mode_setcrtc] [CRTC:242:pipe D]
<6> [824.920597] [IGT] kms_invalid_dotclock: exiting, ret=77
<5> [824.920904] Setting dangerous option reset - tainting kernel
<7> [824.922238] [drm:intel_atomic_check [i915]] [CONNECTOR:244:eDP-1] Limiting display bpp to 24 instead of EDID bpp 24, requested bpp 36, max platform bpp 36
<7> [824.922290] [drm:intel_dp_compute_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz
<7> [824.922331] [drm:intel_dp_compute_config [i915]] Force DSC en = 0
<7> [824.922375] [drm:intel_dp_compute_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [824.922403] [drm:intel_dp_compute_config [i915]] DP link rate required 1083930 available 2160000
<7> [824.922433] [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long
<7> [824.922466] [drm:intel_atomic_check [i915]] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [824.922499] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [824.922558] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_htotal (expected 0, found 3316)
<7> [824.922590] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [824.922623] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_hblank_end (expected 0, found 3316)
<7> [824.922653] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [824.922683] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [824.922713] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [824.922742] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vtotal (expected 0, found 1816)
<7> [824.922803] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [824.922830] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vblank_end (expected 0, found 1816)
<7> [824.922855] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vsync_start (expected 0, found 1802)
<7> [824.922884] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_vsync_end (expected 0, found 1807)
<7> [824.922909] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.flags (2) (expected 0, found 2)
<7> [824.922935] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.flags (8) (expected 0, found 8)
<7> [824.922960] [drm:pipe_config_mismatch [i915]] fastset mismatch in base.adjusted_mode.crtc_clock (expected 0, found 361310)
<7> [824.922989] [drm:intel_atomic_check [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [824.923015] [drm:intel_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [824.923048] [drm:intel_find_shared_dpll [i915]] [CRTC:83:pipe A] allocated DPLL 0
<7> [824.923074] [drm:intel_reference_shared_dpll.isra.10 [i915]] using DPLL 0 for pipe A
<7> [824.923101] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb (   0 -    0) -> (   0 -  969), size    0 ->  969
<7> [824.923122] [drm:skl_compute_wm [i915]] [PLANE:80:cursor A] ddb (   0 -    0) -> ( 969 - 1024), size    0 ->   55
<7> [824.923140] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm
<7> [824.923158] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0 ->    1,   7,   8,   9,  12,  14,  14,  16,   0
<7> [824.923176] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0 ->   19, 183, 209, 235, 313, 365, 365, 417,  33
<7> [824.923193] [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0 ->   22, 203, 231, 260, 346, 403, 403, 460,   0
<7> [824.923232] [drm:intel_bw_atomic_check [i915]] pipe A data rate 1445240 num active planes 1
<7> [824.923264] [drm:intel_dump_pipe_config [i915]] [CRTC:83:pipe A] enable: yes [modeset]
<7> [824.923292] [drm:intel_dump_pipe_config [i915]] active: yes, output_types: EDP (0x100), output format: RGB
<7> [824.923318] [drm:intel_dump_pipe_config [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [824.923348] [drm:intel_dump_pipe_config [i915]] dp m_n: lanes: 4; gmch_m: 16443, gmch_n: 32768, link_m: 21924, link_n: 32768, tu: 64
<7> [824.923376] [drm:intel_dump_pipe_config [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [824.923403] [drm:intel_dump_pipe_config [i915]] requested mode:
<7> [824.923407] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [824.923431] [drm:intel_dump_pipe_config [i915]] adjusted mode:
<7> [824.923434] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [824.923469] [drm:intel_dump_pipe_config [i915]] crtc timings: 361310 3200 3248 3280 3316 1800 1802 1807 1816, type: 0x48 flags: 0xa
<7> [824.923495] [drm:intel_dump_pipe_config [i915]] port clock: 540000, pipe src size: 3200x1800, pixel rate 361310
<7> [824.923547] [drm:intel_dump_pipe_config [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1
<7> [824.923577] [drm:intel_dump_pipe_config [i915]] pch pfit: pos: 0x00000000, size: 0x00000000, disabled, force thru: no
<7> [824.923605] [drm:intel_dump_pipe_config [i915]] ips: 0, double wide: 0
<7> [824.923637] [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x48, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [824.923665] [drm:intel_dump_pipe_config [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [824.923692] [drm:intel_dump_pipe_config [i915]] [PLANE:31:plane 1A] fb: [FB:265] 3200x1800 format = XR24 little-endian (0x34325258), visible: yes
<7> [824.923719] [drm:intel_dump_pipe_config [i915]] 	rotation: 0x1, scaler: -1
<7> [824.923745] [drm:intel_dump_pipe_config [i915]] 	src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [824.923771] [drm:intel_dump_pipe_config [i915]] [PLANE:38:plane 2A] fb: [NOFB], visible: no
<7> [824.923797] [drm:intel_dump_pipe_config [i915]] [PLANE:45:plane 3A] fb: [NOFB], visible: no
<7> [824.923823] [drm:intel_dump_pipe_config [i915]] [PLANE:52:plane 4A] fb: [NOFB], visible: no
<7> [824.923848] [drm:intel_dump_pipe_config [i915]] [PLANE:59:plane 5A] fb: [NOFB], visible: no
<7> [824.923874] [drm:intel_dump_pipe_config [i915]] [PLANE:66:plane 6A] fb: [NOFB], visible: no
<7> [824.923898] [drm:intel_dump_pipe_config [i915]] [PLANE:73:plane 7A] fb: [NOFB], visible: no
<7> [824.923923] [drm:intel_dump_pipe_config [i915]] [PLANE:80:cursor A] fb: [NOFB], visible: no
<7> [824.924105] [drm:intel_power_well_enable [i915]] enabling always-on
<7> [824.924132] [drm:intel_power_well_enable [i915]] enabling DC off
<7> [824.924712] [drm:gen9_set_dc_state [i915]] Setting DC state from 02 to 00
<7> [824.924795] [drm:intel_combo_phy_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [824.924842] [drm:intel_combo_phy_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [824.924888] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [824.924999] [drm:intel_atomic_commit_tail [i915]] [ENCODER:243:DDI A]
<7> [824.925024] [drm:intel_atomic_commit_tail [i915]] [ENCODER:249:DDI B]
<7> [824.925048] [drm:intel_atomic_commit_tail [i915]] [ENCODER:251:DP-MST A]
<7> [824.925075] [drm:intel_atomic_commit_tail [i915]] [ENCODER:252:DP-MST B]
<7> [824.925102] [drm:intel_atomic_commit_tail [i915]] [ENCODER:253:DP-MST C]
<7> [824.925129] [drm:intel_atomic_commit_tail [i915]] [ENCODER:254:DP-MST D]
<7> [824.925160] [drm:verify_single_dpll_state.isra.112 [i915]] DPLL 0
<7> [824.925208] [drm:verify_single_dpll_state.isra.112 [i915]] DPLL 1
<7> [824.925246] [drm:verify_single_dpll_state.isra.112 [i915]] TBT PLL
<7> [824.925293] [drm:intel_power_well_enable [i915]] enabling AUX A
<7> [824.925336] [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 1, on? 0) for crtc 83
<7> [824.925370] [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [824.925445] [drm:edp_panel_on [i915]] Turn [ENCODER:243:DDI A] panel power on
<7> [824.925500] [drm:wait_panel_power_cycle [i915]] Wait for panel power cycle
<7> [825.553705] [drm:wait_panel_status [i915]] mask b800000f value 00000000 status 00000000 control 00000060
<7> [825.553801] [drm:wait_panel_status [i915]] Wait complete
<7> [825.553934] [drm:edp_panel_on [i915]] Wait for panel power on
<7> [825.554102] [drm:wait_panel_status [i915]] mask b000000f value 80000008 status 9000000a control 00000063
<7> [825.612841] [drm:gen8_de_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [825.612946] [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:243:DDI A] - long
<7> [825.613045] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 40
<7> [825.613188] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:243:DDI A]
<7> [825.765189] [drm:wait_panel_status [i915]] Wait complete
<7> [825.765331] [drm:intel_power_well_enable [i915]] enabling DDI A IO
<7> [825.765803] [drm:edp_panel_vdd_on [i915]] Turning [ENCODER:243:DDI A] VDD on
<7> [825.766088] [drm:edp_panel_vdd_on [i915]] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [825.767194] [drm:intel_dp_start_link_train [i915]] Using LINK_BW_SET value 14
<7> [825.768689] [drm:intel_dp_set_signal_levels [i915]] Using vswing level 0
<7> [825.768797] [drm:intel_dp_set_signal_levels [i915]] Using pre-emphasis level 0
<7> [825.768907] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS1
<7> [825.770565] [drm:intel_dp_set_signal_levels [i915]] Using vswing level 1
<7> [825.770721] [drm:intel_dp_set_signal_levels [i915]] Using pre-emphasis level 0
<7> [825.772117] [drm:intel_dp_start_link_train [i915]] clock recovery OK
<7> [825.772225] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS3
<7> [825.774124] [drm:intel_dp_set_signal_levels [i915]] Using vswing level 1
<7> [825.774238] [drm:intel_dp_set_signal_levels [i915]] Using pre-emphasis level 1
<7> [825.775869] [drm:intel_dp_start_link_train [i915]] Channel EQ done. DP Training successful
<7> [825.776121] [drm:intel_dp_start_link_train [i915]] [CONNECTOR:244:eDP-1] Link Training Passed at Link Rate = 540000, Lane count = 4
<7> [825.776756] [drm:intel_enable_pipe [i915]] enabling pipe A
<7> [825.777071] [drm:intel_edp_backlight_on [i915]] 
<7> [825.777182] [drm:intel_panel_enable_backlight [i915]] pipe A
<7> [825.777348] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 96000
<7> [825.777714] [drm:intel_enable_ddi [i915]] Panel doesn't support DRRS
<7> [825.787700] [drm:intel_fbc_enable [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, threshold: 1
<7> [825.787737] [drm:intel_fbc_enable [i915]] Enabling FBC on pipe A
<7> [825.793822] [drm:verify_connector_state [i915]] [CONNECTOR:244:eDP-1]
<7> [825.793886] [drm:intel_atomic_commit_tail [i915]] [CRTC:83:pipe A]
<7> [825.793992] [drm:verify_single_dpll_state.isra.112 [i915]] DPLL 0
<6> [825.794320] Console: switching to colour frame buffer device 400x112
Created at 2019-09-07 09:51:14