Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.4-gb024a3b67 (x86_64) (Linux: 7.1.0-rc5-CI_DRM_18556-g1e5fbf0d628c+ x86_64)
Out	Using IGT_SRANDOM=1779811984 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888142b81840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x1bba/0x20c0 [i915] intel_atomic_commit+0x2ff/0x350 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0x103/0x6d0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.416s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888142b81840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x300 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0x103/0x6d0
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.416s)
Dmesg	<6> [68.894530] Console: switching to colour dummy device 80x25 <6> [68.894582] [IGT] kms_pm_rpm: executing <6> [68.896670] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [68.896893] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [68.901818] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [68.901825] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.906134] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [68.906391] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [68.906395] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.910635] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [68.910895] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [68.910901] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.915134] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [68.915359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [68.915363] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.919574] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [68.919586] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [68.919589] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.923797] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [68.923809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [68.923811] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.928039] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [68.928056] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [68.928059] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.928918] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.929131] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.929273] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.933076] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [68.933109] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [68.933112] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.937946] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [68.937980] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [68.937983] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.942822] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [69.048228] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [69.945446] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [69.951654] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [69.952969] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [69.953384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [69.953699] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [69.953838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [69.956573] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [69.980699] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [69.987646] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [69.988024] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [69.988940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [69.989886] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.990788] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.991683] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.992560] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.993393] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [69.993923] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [69.994056] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [69.994387] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [69.995070] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [69.995204] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.001351] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.001837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.001983] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [70.002843] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [70.006469] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [70.011375] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [70.016213] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.016353] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.016501] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.017328] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.018744] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [70.018835] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [70.037699] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.038063] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.038389] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.039896] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.040436] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.046251] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.047839] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.048592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.049361] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.049884] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.054496] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.119988] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [70.131815] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.140623] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.141472] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.142398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.143356] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.144285] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.145196] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.146101] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.146375] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.146628] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.146762] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.147171] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.147873] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.148010] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.154156] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.154494] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.154652] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.155369] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.156830] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [70.157002] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [70.161399] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [70.165737] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [70.165895] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [70.184816] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.185166] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.185484] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.186989] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.187445] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.193191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.194659] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.195385] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.196246] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.196825] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.201683] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.278891] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.287716] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.288565] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.289496] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.290444] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.291382] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.292302] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.293210] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.294101] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.295790] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.296560] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.298263] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.300769] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.301542] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.310862] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.311043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.312205] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [70.312856] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [70.313049] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [70.317132] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [70.322038] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [70.327008] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.328000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.329476] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [70.329670] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [70.417123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.418068] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.418927] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.420910] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.422477] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.430960] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.432653] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.433490] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.434380] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.435043] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.439808] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.548536] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.556872] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.557725] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.558702] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.559841] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.560751] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.561727] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.562661] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.562847] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.563229] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.563364] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.563739] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.564454] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.564592] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.571964] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.572133] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.572306] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.573175] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.574596] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [70.574667] [IGT] kms_pm_rpm: exiting, ret=0 <7> [70.574593] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [70.578905] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <6> [70.583527] Console: switching to colour frame buffer device 160x45 <7> [70.584147] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2]

Created at 2026-05-27 00:01:45