Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.4-g7ed262f8d (x86_64) (Linux: 7.0.0-CI_DRM_18331-g19fc8405447f+ x86_64)
Out 
Using IGT_SRANDOM=1776187036 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.292s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.292s)
Dmesg
<6> [177.846550] Console: switching to colour dummy device 80x25
<6> [177.846775] [IGT] kms_force_connector_basic: executing
<7> [177.859376] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.860507] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [177.871761] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.872778] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.872786] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [177.872791] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [177.877037] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [177.877063] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [177.877067] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [177.881268] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [177.881301] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [177.881304] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [177.885519] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<6> [177.885718] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [177.885985] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [177.885989] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [177.885993] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [177.945013] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.950967] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.950989] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.951188] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.956682] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.956687] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.956814] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] status updated from disconnected to connected
<7> [177.956860] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [177.956863] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.956866] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.956869] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.956871] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.956874] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.956901] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [177.956905] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [177.958446] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [177.958514] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [178.016006] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [178.021667] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [178.021678] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [178.021960] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [178.027438] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [178.027444] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [178.027610] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [178.027614] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [178.027617] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [178.027620] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [178.027623] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [178.027626] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [178.027903] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:529:HDMI-A-1] EDID override set
<7> [178.027918] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.027921] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.028510] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:529:HDMI-A-1] ELD monitor IGT
<7> [178.028514] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:529:HDMI-A-1] ELD size 24, SAD count 0
<7> [178.089003] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [178.094857] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [178.094959] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [178.094969] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [178.094974] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [178.094977] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [178.094980] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [178.094983] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [178.094986] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [178.094989] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [178.095111] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:HDMI-A-1] EDID override reset
<7> [178.095321] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.095323] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.156857] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [178.162588] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [178.162596] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [178.162730] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [178.168133] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [178.168138] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [178.168259] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:529:HDMI-A-1] EDID changed, epoch counter 2
<7> [178.168297] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [178.168303] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [178.168311] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [178.168314] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [178.168316] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [178.168319] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [178.168321] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [178.168323] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [178.168443] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [178.168449] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.168454] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.172883] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] status updated from connected to disconnected
<7> [178.172910] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [178.172975] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [178.173080] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [178.173158] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.173168] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.177745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<6> [178.177992] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [178.178461] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [178.179583] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:508:eDP-1] force updated from 0 to 0 or reprobing
<7> [178.179588] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [178.179591] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [178.180188] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [178.180593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [178.180727] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.180857] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.181002] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [178.181006] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [178.181009] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [178.181012] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [178.181024] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [178.181152] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [178.181280] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [178.181742] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [178.181745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [178.181769] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [178.181772] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [178.182317] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [178.182711] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [178.182838] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.182965] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.183104] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [178.183107] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [178.183110] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [178.183114] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [178.183123] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [178.183249] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [178.183374] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [178.183812] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [178.183815] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [178.183889] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:508:eDP-1] EDID override reset
<7> [178.183900] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [178.183903] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [178.184467] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [178.184868] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [178.184997] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.185125] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.185262] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [178.185266] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [178.185269] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [178.185272] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [178.185282] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [178.185409] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [178.185552] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [178.185982] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [178.185985] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [178.186060] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:517:DP-1] EDID override reset
<7> [178.186071] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1]
<7> [178.186074] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:517:DP-1]
<7> [178.190289] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1] disconnected
<7> [178.190390] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [178.190394] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.190397] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.194601] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [178.194624] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.194627] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.198816] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [178.198881] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:HDMI-A-1] EDID override reset
<7> [178.198892] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.198895] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.203129] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [178.203196] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:535:DP-2] EDID override reset
<7> [178.203206] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [178.203209] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:535:DP-2]
<7> [178.203487] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [178.203553] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:544:DP-3] EDID override reset
<7> [178.203563] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [178.203567] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:544:DP-3]
<7> [178.203812] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [178.203873] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:553:DP-4] EDID override reset
<7> [178.203883] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [178.203885] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:553:DP-4]
<7> [178.204124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [178.204183] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:562:DP-5] EDID override reset
<7> [178.204193] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5]
<7> [178.204196] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:562:DP-5]
<7> [178.204440] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5] disconnected
<6> [178.204858] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [178.205310] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [178.222838] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [178.222844] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [178.222896] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [178.222900] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [178.223519] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [178.223960] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [178.224098] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.224229] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [178.224373] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [178.224377] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [178.224381] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [178.224384] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [178.224397] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [178.224562] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [178.224714] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [178.225184] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [178.225187] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [178.225191] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1]
<7> [178.225195] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:517:DP-1]
<7> [178.229382] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1] disconnected
<7> [178.229387] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [178.229390] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [178.233648] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [178.233651] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [178.233654] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:535:DP-2]
<7> [178.233920] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [178.233924] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [178.233927] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:544:DP-3]
<7> [178.234186] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [178.234190] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [178.234193] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:553:DP-4]
<7> [178.234459] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [178.234462] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5]
<7> [178.234464] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:562:DP-5]
<7> [178.234720] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5] disconnected
<7> [178.234723] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:508:eDP-1] enabled? yes
<7> [178.234726] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:517:DP-1] enabled? no
<7> [178.234728] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:529:HDMI-A-1] enabled? no
<7> [178.234730] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:535:DP-2] enabled? no
<7> [178.234733] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:544:DP-3] enabled? no
<7> [178.234735] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:553:DP-4] enabled? no
<7> [178.234737] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:562:DP-5] enabled? no
<7> [178.234762] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [178.234772] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:508:eDP-1] found preferred mode: 3840x2400
<7> [178.234775] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [178.234789] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:151:pipe A] desired mode 3840x2400 set (0,0)
<7> [178.239528] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [178.256262] Console: switching to colour frame buffer device 240x75
Created at 2026-04-15 03:00:14