Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.52 seconds
Igt-Version 
IGT-Version: 2.4-g93abaf017 (x86_64) (Linux: 7.0.0-rc7-CI_DRM_18313-g3751e2e5a19a+ x86_64)
Out 
Using IGT_SRANDOM=1775841421 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810df9d828 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.524s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 2
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810df9d828 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b7c/0x26e0
     do_syscall_64+0xdd/0x1440

ref_tracker: intel_runtime_pm@ffff88810df9d828 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get+0x1a/0x30 [i915]
     intel_display_rpm_get+0x1f/0x30 [i915]
     intel_display_power_get+0x22/0x70 [i915]
     i915_hpd_poll_init_work+0x1b2/0x2e0 [i915]
     process_one_work+0x239/0x760
     worker_thread+0x200/0x3f0
     kthread+0x10d/0x150
     ret_from_fork+0x3d4/0x480
     ret_from_fork_asm+0x1a/0x30
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.524s)
Dmesg
<6> [132.615776] Console: switching to colour dummy device 80x25
<6> [132.615845] [IGT] kms_pm_rpm: executing
<6> [132.623477] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [132.623768] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [132.627218] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [132.627226] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [132.628607] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [132.628868] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [132.629131] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [132.629382] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [132.632287] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [132.632675] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [132.632680] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [132.633300] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [132.633818] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [132.634356] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [132.635111] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [132.635638] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [132.636241] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [132.636589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [132.636594] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [132.637012] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.637219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [132.637721] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.637935] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.637939] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [132.638115] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [132.642231] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.642235] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [132.642423] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [132.642705] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [132.642710] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [132.646944] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [132.646960] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [132.646965] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [132.647695] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [132.648171] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [132.648793] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [132.648809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [132.648813] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [132.649248] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.649424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [132.649858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.650072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.650076] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [132.650252] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [132.654430] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.654435] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [132.654664] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [132.654687] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [132.654691] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [132.658963] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [132.659004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [132.659008] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [132.659738] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [132.660215] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [132.660847] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [132.660886] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [132.660890] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [132.661347] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.661539] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [132.661967] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [132.662201] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.662205] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [132.662384] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [132.666459] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [132.666464] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [132.666697] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [132.740717] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [132.741404] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [132.742029] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [132.742677] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [132.743805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [143.720263] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [143.730429] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [143.755195] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [143.761095] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [143.762091] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [143.762478] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [143.763322] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [143.767184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [143.767866] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [143.768435] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [143.769011] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [143.770021] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [143.770796] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [143.772021] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [143.772474] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [143.772665] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [143.773072] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [143.773292] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [143.773297] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [143.773487] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [143.777719] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [143.777723] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [143.778130] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [143.778263] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [143.876165] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [143.876719] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [143.877220] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [143.877794] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [143.878844] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [143.879481] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [143.884048] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [143.980031] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [143.992170] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [144.002215] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [144.002807] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [144.003530] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [144.004562] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [144.005718] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [144.006036] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [144.010470] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [144.011076] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [144.012345] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [144.013165] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [144.014362] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [144.014821] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.015067] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [144.015550] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.015780] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.015785] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [144.016007] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [144.020292] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.020297] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [144.020644] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [144.023058] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [144.023277] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [144.023476] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [144.023672] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [144.024328] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [144.024695] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [144.029045] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [144.133596] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [144.142616] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [144.143109] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [144.143640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [144.144557] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [144.146375] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [144.148045] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [144.148691] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [144.151035] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [144.151531] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [144.152726] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [144.153600] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [144.154962] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [144.155078] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [144.157013] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [144.157450] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.157628] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [144.158097] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.158322] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.158326] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [144.158502] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [144.162751] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.162756] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [144.252134] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [144.252496] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [144.252813] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [144.253149] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [144.253980] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [144.254684] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [144.260017] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [144.373127] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [144.382351] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [144.383112] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [144.383337] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [144.383917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [144.384819] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [144.384920] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [144.385265] [IGT] kms_pm_rpm: exiting, ret=0
<7> [144.389208] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [144.389522] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [144.390538] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [144.391314] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [144.393161] Console: switching to colour frame buffer device 128x48
<7> [144.393925] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [144.394480] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.394673] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [144.395119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [144.395344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.395349] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [144.395525] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [144.399964] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [144.399969] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [144.402080] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [144.402297] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [144.402496] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [144.402691] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
Created at 2026-04-11 17:07:18