Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.4-g81169c743 (x86_64) (Linux: 7.0.0-rc7-CI_DRM_18296-g994d34e9b0e7+ x86_64)
Out 
Using IGT_SRANDOM=1775710368 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.292s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.292s)
Dmesg
<6> [172.064307] Console: switching to colour dummy device 80x25
<6> [172.064589] [IGT] kms_force_connector_basic: executing
<7> [172.077149] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.078593] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [172.092502] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.093888] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [172.093898] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.093905] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.098140] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.098172] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.098175] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.102413] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.102452] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.102455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.106643] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<6> [172.106820] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [172.107069] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [172.107073] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.107076] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.166893] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.172621] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.172638] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.173004] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.178649] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.178657] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.178913] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] status updated from disconnected to connected
<7> [172.179003] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [172.179008] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.179014] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.179019] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.179023] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.179027] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.179061] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.179065] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.180326] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [172.180397] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [172.237900] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.243514] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.243523] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.243678] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.249150] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.249157] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.249374] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [172.249379] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.249384] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.249388] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.249391] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.249395] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.249715] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:529:HDMI-A-1] EDID override set
<7> [172.249734] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.249738] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.250037] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:529:HDMI-A-1] ELD monitor IGT
<7> [172.250041] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:529:HDMI-A-1] ELD size 24, SAD count 0
<7> [172.310890] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.316565] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [172.316658] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [172.316667] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [172.316671] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [172.316674] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [172.316678] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [172.316681] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.316684] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.316688] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.316785] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:HDMI-A-1] EDID override reset
<7> [172.316976] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.316979] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.377887] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.383660] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.383673] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.383998] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.389652] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.389662] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.389894] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:529:HDMI-A-1] EDID changed, epoch counter 2
<7> [172.389953] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [172.389962] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [172.389971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] probed modes:
<7> [172.389976] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.389981] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.389986] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.389990] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.389994] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.390148] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [172.390151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.390154] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.394409] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] status updated from connected to disconnected
<7> [172.394416] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.394437] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [172.394473] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [172.394495] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.394498] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.398703] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<6> [172.399007] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [172.399439] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.400542] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:508:eDP-1] force updated from 0 to 0 or reprobing
<7> [172.400548] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [172.400551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [172.401133] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.401550] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.401684] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.401814] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.401968] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.401973] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.401976] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [172.401979] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [172.401992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [172.402123] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.402252] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.402715] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [172.402719] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.402742] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [172.402745] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [172.403283] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.403691] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.403825] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.403952] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.404095] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.404099] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.404102] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [172.404104] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [172.404115] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [172.404248] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.404398] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.404815] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [172.404818] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.404888] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:508:eDP-1] EDID override reset
<7> [172.404899] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [172.404902] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [172.405443] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.405823] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.405960] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.406090] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.406231] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.406235] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.406238] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [172.406240] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [172.406251] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [172.406398] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.406530] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.406961] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [172.406964] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.407036] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:517:DP-1] EDID override reset
<7> [172.407047] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1]
<7> [172.407050] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:517:DP-1]
<7> [172.411273] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1] disconnected
<7> [172.411393] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:529:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [172.411397] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.411400] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.415621] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.415641] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.415644] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.419827] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.419891] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:HDMI-A-1] EDID override reset
<7> [172.419901] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.419904] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.424120] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.424185] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:535:DP-2] EDID override reset
<7> [172.424195] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [172.424198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:535:DP-2]
<7> [172.424487] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [172.424567] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:544:DP-3] EDID override reset
<7> [172.424577] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [172.424580] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:544:DP-3]
<7> [172.424823] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [172.424883] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:553:DP-4] EDID override reset
<7> [172.424893] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [172.424896] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:553:DP-4]
<7> [172.425136] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [172.425192] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:562:DP-5] EDID override reset
<7> [172.425202] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5]
<7> [172.425204] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:562:DP-5]
<7> [172.425496] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5] disconnected
<6> [172.425887] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [172.426271] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [172.443801] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [172.443806] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [172.443850] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1]
<7> [172.443854] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:508:eDP-1]
<7> [172.444434] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.444834] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.444967] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.445094] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.445232] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.445236] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.445239] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD monitor
<7> [172.445242] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:508:eDP-1] ELD size 20, SAD count 0
<7> [172.445253] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] VRR capable: yes
<7> [172.445415] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.445545] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:508:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.445984] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:508:eDP-1] probed modes:
<7> [172.445987] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.445991] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1]
<7> [172.445994] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:517:DP-1]
<7> [172.450212] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:517:DP-1] disconnected
<7> [172.450216] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1]
<7> [172.450219] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:529:HDMI-A-1]
<7> [172.454493] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:HDMI-A-1] disconnected
<7> [172.454497] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2]
<7> [172.454500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:535:DP-2]
<7> [172.454766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:535:DP-2] disconnected
<7> [172.454769] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3]
<7> [172.454772] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:544:DP-3]
<7> [172.455013] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:544:DP-3] disconnected
<7> [172.455016] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4]
<7> [172.455019] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:553:DP-4]
<7> [172.455260] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:553:DP-4] disconnected
<7> [172.455263] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5]
<7> [172.455266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:562:DP-5]
<7> [172.455543] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:562:DP-5] disconnected
<7> [172.455547] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:508:eDP-1] enabled? yes
<7> [172.455550] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:517:DP-1] enabled? no
<7> [172.455553] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:529:HDMI-A-1] enabled? no
<7> [172.455555] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:535:DP-2] enabled? no
<7> [172.455557] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:544:DP-3] enabled? no
<7> [172.455559] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:553:DP-4] enabled? no
<7> [172.455561] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:562:DP-5] enabled? no
<7> [172.455583] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [172.455595] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:508:eDP-1] found preferred mode: 3840x2400
<7> [172.455597] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [172.455619] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:151:pipe A] desired mode 3840x2400 set (0,0)
<7> [172.460484] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [172.477245] Console: switching to colour frame buffer device 240x75
Created at 2026-04-09 15:04:58