Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.34 seconds
Igt-Version 
IGT-Version: 2.4-gbdaaf0b25 (x86_64) (Linux: 7.0.0-rc6-CI_DRM_18272-gdba2251b00d3+ x86_64)
Out 
Using IGT_SRANDOM=1775147448 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888136361828 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.343s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.343s)
Dmesg
<6> [120.801520] Console: switching to colour dummy device 80x25
<6> [120.801624] [IGT] kms_pm_rpm: executing
<7> [120.805682] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [120.812231] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [120.812243] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [120.812556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.813747] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.814493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.815243] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.815873] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.816215] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.817176] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.818780] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.820222] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.821746] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.823310] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.824987] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.826633] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.828213] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.829751] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.830639] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.831413] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.831786] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.832393] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [120.832972] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [120.832980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [120.837370] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [120.837898] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [120.837906] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [120.905729] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.909512] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.909523] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.909867] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.913059] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.913069] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.913432] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [120.913965] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [120.913975] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [120.914806] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.915283] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.916266] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.917986] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.919588] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.921180] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.922992] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.924686] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.926390] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.928234] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.929949] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.930991] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.931885] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.932338] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.933034] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [120.933095] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [120.933107] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [120.937630] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [120.937670] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [120.937678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [121.006125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.009654] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.009666] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.010073] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.013392] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.013404] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.013816] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [121.013882] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [121.013892] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [121.014740] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [121.015330] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [121.016366] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.018067] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.019787] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.021443] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.023258] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.025072] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.026882] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.028717] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.030353] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.031451] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [121.032477] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [121.032926] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [121.033747] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [121.033872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [121.033882] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [121.038428] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [121.038543] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [121.038552] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [121.106722] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.110534] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.110546] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.110944] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.114240] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.114252] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.114668] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [121.125216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.125721] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.126188] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.126798] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.127790] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.122548] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.129554] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.154280] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.164973] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.166191] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [122.166034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.166497] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.167174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.167990] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [122.167910] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.168439] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.169848] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.170227] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.171083] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.172685] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.174196] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.175779] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.177423] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.179074] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.180763] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.182388] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.183944] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.184895] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.185928] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.186687] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.187919] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.192451] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.260712] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.264655] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.264670] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.265141] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.268819] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.268833] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.270539] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [122.292315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.293100] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.293666] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.294293] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.295337] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.296567] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.304916] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [122.376316] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [122.429920] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [122.442145] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.448887] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.449656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.449934] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.450947] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.451901] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.452438] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.452968] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [122.453363] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.453769] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.454631] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.456089] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.457679] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.459165] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.460736] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.462302] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.464057] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.465675] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.467200] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.468245] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.469218] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.469874] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.471699] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.476391] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [122.476732] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.545123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.548799] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.548811] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.549192] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.552566] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.552577] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.572147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.572835] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.573453] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.574174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.575337] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.576756] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.586087] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.690340] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.711294] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.713578] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.714764] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.714745] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.716483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.718833] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [122.721209] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [122.721884] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.723464] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.725508] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.727690] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.729587] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.731351] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.733370] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.735176] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.737044] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.738967] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.740653] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.741666] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.743238] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.744003] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.745472] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.750042] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.818106] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.821747] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.821758] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.822127] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.825488] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.825499] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.826279] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [122.826388] [IGT] kms_pm_rpm: exiting, ret=0
<7> [122.828153] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.828649] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.829093] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.829691] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.830756] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.831398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.831789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.832683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [122.833845] Console: switching to colour frame buffer device 128x48
Created at 2026-04-03 16:51:56