Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.17 seconds
Igt-Version 
IGT-Version: 2.3-gbb485cffb (x86_64) (Linux: 7.0.0-rc5-CI_DRM_18219-g2056c24cdb8a+ x86_64)
Out 
Using IGT_SRANDOM=1774511789 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88812d365828 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.166s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.166s)
Dmesg
<6> [101.948892] Console: switching to colour dummy device 80x25
<6> [101.949077] [IGT] kms_pm_rpm: executing
<7> [101.949779] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.950074] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.950275] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.950501] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.951158] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.957114] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [101.960816] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [101.960824] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [101.961015] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.965425] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [101.965783] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [101.965788] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [101.966401] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.966927] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.967453] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.968097] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.968584] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.969253] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [101.969567] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [101.969572] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [101.970060] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.970243] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.970633] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.970846] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.970851] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.971015] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.975150] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.975155] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.975336] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [101.975561] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [101.975565] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [101.979863] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [101.979880] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [101.979884] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [101.980592] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.981076] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.981741] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [101.981761] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [101.981765] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [101.982199] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.982364] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.982766] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.982968] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.982972] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.983136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.987189] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.987194] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.987374] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [101.987397] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [101.987400] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [101.991663] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [101.991713] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [101.991717] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [101.992472] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.992954] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.993551] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [101.993591] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [101.993595] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [101.994073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.994240] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.994620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.994884] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.994888] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.995052] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.999098] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.999103] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.999282] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [102.069928] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.070495] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.071082] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [102.071807] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [102.072939] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.051252] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.058690] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.082135] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.089997] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.091365] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.091783] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [113.092533] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [113.096885] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [113.098216] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.099041] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.099754] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [113.101109] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [113.101973] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [113.103201] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [113.103737] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.103904] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [113.104321] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.104524] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.104529] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [113.104693] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [113.108839] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.108843] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [113.109247] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [113.109440] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [113.205222] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [113.205725] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.206202] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.206636] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.207483] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.208383] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.213473] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [113.311705] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [113.324994] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [113.337120] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.343477] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.344142] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.344461] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.344993] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.345861] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [113.346142] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [113.350516] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [113.350943] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [113.352002] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [113.352789] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [113.354168] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [113.354410] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [113.354867] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.355068] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [113.355479] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.355696] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.355700] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [113.355863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [113.360097] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.360115] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [113.364149] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [113.364354] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.364540] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.364722] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.365398] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.365645] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.369128] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.467060] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.474163] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.474596] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.474952] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.476262] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.477517] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [113.478687] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [113.482168] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [113.482863] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [113.484015] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [113.484792] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [113.485981] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [113.486422] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.486603] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [113.487001] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [113.487253] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.487258] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [113.487450] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [113.491682] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [113.491686] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [113.492173] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [113.492301] [IGT] kms_pm_rpm: exiting, ret=0
<6> [113.493573] Console: switching to colour frame buffer device 128x48
Created at 2026-03-26 23:12:45