Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.43 seconds
Igt-Version	IGT-Version: 2.3-g246d93c1d (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18142-g4082c266f293+ x86_64)
Out	Using IGT_SRANDOM=1773393007 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888144da1820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.427s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888144da1820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.427s)
Dmesg	<6> [60.002213] Console: switching to colour dummy device 80x25 <6> [60.002266] [IGT] kms_pm_rpm: executing <6> [60.004141] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [60.004351] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [60.008493] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.008500] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.012717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.012962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.012965] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.017180] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.017419] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.017422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.021622] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.021897] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.021900] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.026082] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.026094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.026096] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.030301] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.030313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.030315] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.034514] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.034531] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.034533] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.035130] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [60.035325] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [60.035484] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [60.039280] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.039314] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.039316] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.044151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.044181] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.044184] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.049029] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.154288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.050972] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.057123] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.058482] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.058907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.059198] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.059336] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.062182] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.087280] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.095134] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.095975] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.096889] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.097826] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.098762] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.099670] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.100569] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.101441] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.102296] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.102429] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.102858] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.103554] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.103697] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.111062] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.112282] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.113576] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.113694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.114715] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.116177] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.116138] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [61.120411] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.124728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.129036] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.147271] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.147631] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.147954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.149525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.150165] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.153522] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.154850] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.155263] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.155552] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.155710] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.157920] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.230175] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.242330] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.250155] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.250991] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.251903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.252866] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.253800] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.254734] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.255634] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.256509] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.258148] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.258917] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.260424] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.262928] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.263700] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.272832] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.273003] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.273236] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.274033] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.275526] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [61.275717] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.279757] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.284114] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.284234] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.302310] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.302740] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.303165] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.304851] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.305601] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.312573] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.314268] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.315044] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.315840] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.316424] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.320160] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.397351] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.404276] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.404442] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.405348] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.406419] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.407466] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.408565] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.409554] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.410435] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.412348] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.413348] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.415006] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.417746] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.418632] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.428895] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.429025] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.429800] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [61.432289] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [61.432500] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.434776] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.439719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.440768] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.442223] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.442397] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.446531] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.538486] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.539420] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.540256] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.543859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.544821] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.549701] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.551031] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.551266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.551549] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.551685] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.553152] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.664653] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.672175] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.673006] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.673960] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.675078] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.676189] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.677272] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.678270] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.679349] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.679805] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.679943] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.680303] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.681005] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.681151] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.693394] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.693565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.693704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.694627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.696053] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [61.696227] [IGT] kms_pm_rpm: exiting, ret=0 <7> [61.696190] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [61.700466] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <6> [61.704888] Console: switching to colour frame buffer device 160x45 <7> [61.704839] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]

Created at 2026-03-14 08:23:59