Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.3-g611f1cac6 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18141-g721db23a9c23+ x86_64)
Out	Using IGT_SRANDOM=1773385090 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888122021820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.421s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888122021820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.421s)
Dmesg	<6> [60.222731] Console: switching to colour dummy device 80x25 <6> [60.222784] [IGT] kms_pm_rpm: executing <6> [60.224788] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [60.225004] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [60.229718] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.229724] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.233964] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.234207] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.234211] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.238370] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.238609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.238612] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.242809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.243093] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.243096] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.247268] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.247279] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.247282] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.251471] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.251483] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.251485] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.253821] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [60.253975] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [60.254135] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [60.256717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.256741] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [60.256745] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [60.261579] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [60.261609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [60.261612] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [60.266451] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [60.266482] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [60.266484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [60.271334] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [60.373752] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.270014] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.274936] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.276309] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.276559] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.276842] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.276979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.279322] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.304257] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.312083] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.312309] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.312482] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.312710] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.312916] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.313120] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.313316] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.313492] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.313872] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.314007] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.314284] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.316193] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.316802] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.324714] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.325912] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.326191] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [61.328366] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.330867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.335751] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.340615] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.340795] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.340936] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.341727] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.343176] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.343286] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.361073] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.361311] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.361516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.362950] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.363452] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.369259] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.370808] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.371686] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.372488] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.373096] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.376856] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.444259] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.456743] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.464615] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.465444] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.466361] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.467317] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.468252] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.469173] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.470079] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.470957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.472614] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.473400] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.474960] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.477475] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.478275] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.488712] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.488893] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.489119] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.489958] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.491388] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [61.491585] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.495606] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.499909] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.500012] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.517595] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.517745] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.517881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.519154] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.519450] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.524063] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.525429] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.525652] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.525930] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.526074] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.528295] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.612930] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.621207] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.622034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.622975] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.623923] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.624871] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.625793] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.626687] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.627566] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.629191] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.629953] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.631494] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.633985] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.634732] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.643938] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.644186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.644607] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [61.647056] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [61.647243] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [61.649551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [61.654498] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.655539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.657023] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [61.656980] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [61.661338] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [61.753150] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [61.754079] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.754906] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.756905] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [61.757798] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [61.764998] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.766680] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [61.767591] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [61.768652] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [61.769293] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [61.774681] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [61.879871] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [61.888296] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [61.889129] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [61.890110] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [61.891069] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.892033] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.892965] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.893885] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [61.894777] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [61.895716] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [61.896526] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [61.897576] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [61.900134] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [61.900976] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [61.912469] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [61.912690] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [61.912873] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [61.913703] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [61.915342] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [61.915345] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [61.915542] [IGT] kms_pm_rpm: exiting, ret=0 <7> [61.919627] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <6> [61.924036] Console: switching to colour frame buffer device 160x45 <7> [61.923988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]

Created at 2026-03-14 06:21:06