Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.3-g4c8773922 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18137-g3ccc0e340459+ x86_64)
Out 
Using IGT_SRANDOM=1773333068 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.293s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.293s)
Dmesg
<6> [172.243380] Console: switching to colour dummy device 80x25
<6> [172.243619] [IGT] kms_force_connector_basic: executing
<7> [172.250808] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.252004] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [172.262883] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.264003] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [172.264012] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.264016] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.268273] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.268296] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.268299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.272539] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.272573] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.272575] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.276797] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [172.276972] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [172.277248] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [172.277254] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.277257] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.336288] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.342220] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.342240] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.342510] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.348060] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.348066] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.348261] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from disconnected to connected
<7> [172.348316] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [172.348319] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.348322] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.348326] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.348329] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.348332] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.348348] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [172.348421] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [172.348452] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.348454] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.409280] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.415029] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.415039] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.415243] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.420662] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.420668] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.420846] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [172.420850] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.420852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.420855] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.420856] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.420859] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.421041] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:528:HDMI-A-1] EDID override set
<7> [172.421057] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.421060] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.421593] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD monitor IGT
<7> [172.421596] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD size 24, SAD count 0
<7> [172.482276] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.488021] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [172.488153] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [172.488164] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [172.488172] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [172.488176] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [172.488180] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [172.488184] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.488187] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.488190] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.488290] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [172.488488] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.488490] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.549734] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [172.555475] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.555483] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [172.555617] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [172.561028] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [172.561033] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [172.561156] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:528:HDMI-A-1] EDID changed, epoch counter 2
<7> [172.561198] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [172.561205] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [172.561210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [172.561212] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [172.561215] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [172.561218] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [172.561220] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [172.561222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [172.561341] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [172.561344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.561347] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.565683] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from connected to disconnected
<7> [172.565707] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.565745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.565748] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.565929] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [172.565974] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [172.570044] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [172.570586] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [172.571283] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [172.572925] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:507:eDP-1] force updated from 0 to 0 or reprobing
<7> [172.572931] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [172.572934] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [172.573526] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.573946] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.574087] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.574225] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.574384] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.574389] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.574393] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [172.574396] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [172.574409] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [172.574552] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.574695] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.575150] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [172.575153] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.575175] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [172.575178] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [172.575740] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.576131] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.576267] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.576404] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.576552] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.576556] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.576559] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [172.576561] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [172.576572] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [172.576722] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.576855] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.577294] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [172.577296] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.577370] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:507:eDP-1] EDID override reset
<7> [172.577383] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [172.577385] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [172.577929] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.578313] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.578452] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.578590] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.578747] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.578751] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.578754] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [172.578756] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [172.578768] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [172.578900] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.579031] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.579465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [172.579468] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.579543] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:516:DP-1] EDID override reset
<7> [172.579556] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [172.579558] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [172.583883] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [172.584031] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [172.584036] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.584040] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.588304] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.588326] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.588329] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.592525] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.592596] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [172.592608] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.592610] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.596899] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.596971] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:534:DP-2] EDID override reset
<7> [172.596984] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [172.596986] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [172.597259] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [172.597322] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:543:DP-3] EDID override reset
<7> [172.597333] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [172.597335] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [172.597584] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [172.597642] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:552:DP-4] EDID override reset
<7> [172.597653] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [172.597655] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [172.597940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [172.598004] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:561:DP-5] EDID override reset
<7> [172.598015] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [172.598017] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [172.598279] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<6> [172.598720] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [172.599217] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [172.616837] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [172.616848] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [172.616922] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [172.616927] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [172.617516] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [172.617934] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [172.618088] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.618255] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [172.618471] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [172.618477] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [172.618485] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [172.618489] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [172.618503] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [172.618710] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [172.618871] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [172.619310] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [172.619313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [172.619316] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [172.619319] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [172.623532] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [172.623537] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [172.623541] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [172.627794] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [172.627799] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [172.627801] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [172.628063] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [172.628065] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [172.628068] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [172.628329] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [172.628332] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [172.628334] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [172.628577] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [172.628580] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [172.628582] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [172.628867] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<7> [172.628870] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] enabled? yes
<7> [172.628873] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:516:DP-1] enabled? no
<7> [172.628874] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:528:HDMI-A-1] enabled? no
<7> [172.628876] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:534:DP-2] enabled? no
<7> [172.628878] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:543:DP-3] enabled? no
<7> [172.628879] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:552:DP-4] enabled? no
<7> [172.628881] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:561:DP-5] enabled? no
<7> [172.628900] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [172.628909] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] found preferred mode: 3840x2400
<7> [172.628911] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [172.628924] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:150:pipe A] desired mode 3840x2400 set (0,0)
<7> [172.633450] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [172.650209] Console: switching to colour frame buffer device 240x75
Created at 2026-03-13 15:49:12