Results for igt@kms_frontbuffer_tracking@fbc-1p-primscrn-cur-indfb-draw-render

Result: Pass

git-log-oneline i915_display_info24 igt_runner24 runtimes24 results24.json results24-i915-load.json guc_logs24.tar i915_display_info_post_exec24 boot24 dmesg24

DetailValue
Duration 2.79 seconds
Hostname 
shard-dg1-14
Igt-Version 
IGT-Version: 2.3-gd92116c0c (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18134-g169ea69ad8f2+ x86_64)
Out 
Using IGT_SRANDOM=1773384271 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test PSR: no usable eDP screen.
Can't test DRRS: no usable screen.
Starting subtest: fbc-1p-primscrn-cur-indfb-draw-render
Subtest fbc-1p-primscrn-cur-indfb-draw-render: SUCCESS (2.795s)
Err 
Starting subtest: fbc-1p-primscrn-cur-indfb-draw-render
Subtest fbc-1p-primscrn-cur-indfb-draw-render: SUCCESS (2.795s)
Dmesg
<7> [101.564083] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.564298] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [101.564453] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<6> [101.593436] Console: switching to colour dummy device 80x25
<6> [101.593555] [IGT] kms_frontbuffer_tracking: executing
<7> [101.600922] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [101.602152] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [101.602459] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [101.615694] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [101.615702] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [101.615944] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.616142] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [101.616551] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [101.637582] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.658711] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.679873] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.701002] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.722151] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.743270] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.764392] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.785511] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.806655] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.827788] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.848940] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.870081] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.891215] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.912348] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.933485] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.954618] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.975753] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [101.996921] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.018062] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.039201] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.060335] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.081468] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.102605] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.123740] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.144917] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.166059] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.187180] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.208315] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.229449] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.250591] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.271725] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.292875] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.293046] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [102.293090] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [102.293819] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [102.293824] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [102.298097] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [102.298559] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [102.298564] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [102.302752] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [102.303320] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [102.303325] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [102.307550] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [102.308047] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [102.308051] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [102.312253] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [102.312737] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [102.312741] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [102.316938] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [102.317696] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [102.317701] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [102.338808] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.359917] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.381043] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.402178] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.423321] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.444441] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.465562] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.486684] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.507818] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.528967] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.550103] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.571243] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.592378] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.613518] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.634661] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.655796] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.676971] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.698106] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.719240] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.740374] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.761509] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.782642] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.803774] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.824940] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.846086] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.867220] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.888354] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.909492] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.930624] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.951756] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.972938] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.994079] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [102.994245] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [102.994288] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [102.994305] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1]
<7> [102.994310] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:599:HDMI-A-1]
<7> [103.018670] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD monitor FH-DP4K
<7> [103.018676] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD size 36, SAD count 2
<7> [103.018843] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [103.019016] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK on first message, retry
<7> [103.019356] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [103.019526] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [103.019537] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] Assuming DP dual mode adaptor presence based on VBT
<7> [103.019670] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] DP dual mode adaptor (type 1 DVI) detected (max TMDS clock: 165000 kHz)
<7> [103.020472] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1440": 60 241700 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9 (CLOCK_HIGH)
<7> [103.020481] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1600": 60 267820 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9 (CLOCK_HIGH)
<7> [103.020488] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 297000 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [103.020495] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "3840x2160": 30 266640 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9 (CLOCK_HIGH)
<7> [103.020501] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 296703 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [103.020510] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1] probed modes:
<7> [103.020513] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
<7> [103.020517] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 17 151100 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9
<7> [103.020520] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1600": 30 133910 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9
<7> [103.020524] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1440": 30 120850 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9
<7> [103.020527] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x40 0x9
<7> [103.020531] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148352 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [103.020534] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [103.020538] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [103.020541] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [103.020545] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [103.020548] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [103.020552] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [103.020555] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1152x864": 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
<7> [103.020559] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [103.020562] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [103.020566] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
<7> [103.020569] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
<7> [103.020572] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [103.020576] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
<7> [103.020579] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
<7> [103.020583] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [103.020586] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [103.020590] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
<7> [103.020593] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
<7> [103.020596] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
<7> [103.020600] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [103.020629] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [103.020633] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [103.024848] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [103.024864] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [103.024868] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [103.029102] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [103.029118] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [103.029122] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [103.033328] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [103.033343] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [103.033347] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [103.037549] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [103.037565] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [103.037568] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [103.041749] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [103.043860] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [103.043957] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [103.044124] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [103.044273] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [103.044406] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<6> [103.046794] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-cur-indfb-draw-render
<7> [103.047709] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [103.047801] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [103.047915] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [103.048120] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [103.048238] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<7> [103.048797] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [103.100132] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [103.158360] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<7> [103.175285] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [103.175389] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [103.193228] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.193910] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.194562] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.195258] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.195886] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.233301] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [103.268730] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [103.283962] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [103.343799] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [103.344233] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [103.376108] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.376542] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.376938] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.411346] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.412237] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.428330] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:642] from all active usage due to RMFB ioctl
<7> [103.428598] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:642] is removed
<7> [103.428799] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [103.429663] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [103.430491] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [103.431431] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [103.432259] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [103.433177] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [103.434023] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [103.443243] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:633]
<7> [103.443883] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [103.444558] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:645]
<7> [103.445215] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:646]
<7> [103.459221] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.460144] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.461012] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.629720] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.629903] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.708849] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [103.708940] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [103.709174] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [103.709547] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [103.709900] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [103.710275] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [103.710631] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [103.711052] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [103.711413] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [103.711770] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [103.727070] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.727276] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.727449] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.727648] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.727825] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.734190] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [103.742720] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [103.751443] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [103.811078] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [103.811447] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [103.843152] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.843941] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.844824] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.877142] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.878038] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.892378] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [103.892579] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [103.909324] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.909623] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [103.910255] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.911144] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.913791] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.914672] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.943182] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.944112] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [103.944942] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [103.977063] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.977913] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [103.992390] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [103.992593] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [104.009584] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.010727] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.011652] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.012524] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.015177] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.016040] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.044163] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.045086] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.045918] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.077057] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.077906] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.092382] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [104.092590] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [104.109616] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.110747] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.111672] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.112538] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.115282] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.116151] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.143186] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.144112] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.144945] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.177148] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.178043] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.195095] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:646] from all active usage due to RMFB ioctl
<7> [104.195370] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:646] is removed
<7> [104.195572] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [104.196429] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [104.197275] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [104.198122] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [104.198920] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [104.199843] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [104.200682] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [104.226165] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.227077] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.227911] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.251817] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [104.280669] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.280857] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.358870] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [104.358970] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [104.359216] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [104.359607] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [104.360000] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [104.360378] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [104.360753] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [104.361194] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [104.361579] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [104.361959] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [104.365041] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [104.365525] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [104.402325] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [104.416723] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [104.426779] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [104.476970] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.477255] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [104.494105] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.494350] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.494559] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.520515] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.521916] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.522337] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.599124] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.620321] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.621252] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.622140] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.660398] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.661288] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.677767] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [104.694178] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.695253] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.696231] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.697365] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [104.698207] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [104.699027] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 6, 11, 11, 11, 17, 17, 19, 21, 20, 0, 0
<7> [104.699825] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 14, 14, 14, 20, 20, 22, 25, 21, 0, 0
<7> [104.701342] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.702217] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.704478] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [104.722148] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.722748] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.723347] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.750840] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.753731] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.754614] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.832400] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.845328] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.846258] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.847128] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.893706] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.894607] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [104.911044] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [104.926180] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.927114] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [104.927948] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [104.932961] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [104.979845] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [104.982747] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.983648] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.065752] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.076330] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.077246] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.078113] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.127078] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.127935] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.144241] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [105.159184] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.160114] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.160950] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.162584] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [105.208848] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.211747] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.212635] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.299155] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.300385] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.301321] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.302187] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.303111] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.303957] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.326200] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.327111] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.327944] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.360407] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.361301] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.377536] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [105.394186] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.395119] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.395780] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [105.395957] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.446741] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.449702] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.450603] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.532448] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.559206] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.560121] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.560954] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.593724] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.594625] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.611093] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [105.627189] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.628119] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.628949] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.630932] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [105.676848] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.679747] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.680637] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.765913] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [105.793197] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.794124] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.794955] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.827076] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.827929] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<6> [105.842852] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-cur-indfb-draw-render, SUCCESS
<7> [105.845217] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:637] from all active usage due to RMFB ioctl
<7> [105.845485] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:637] is removed
<7> [105.845692] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [105.846550] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [105.847373] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.848210] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.849031] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.849934] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [105.850900] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [105.851732] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [105.858396] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<6> [105.877406] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [105.879915] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [105.893256] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.894188] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [105.895076] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [105.920978] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [105.921849] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [105.922701] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [105.923537] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [105.924373] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [105.925205] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [105.926025] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] lines 3, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.926819] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] blocks 6, 11, 11, 11, 17, 17, 19, 21, 20, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.928047] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] min_ddb 8, 14, 14, 14, 20, 20, 22, 25, 21, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [105.928975] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [105.929851] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [105.930901] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [105.934219] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.935104] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [105.936355] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [105.937212] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [105.942121] i915 0000:03:00.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [105.958673] Console: switching to colour frame buffer device 240x67
Created at 2026-03-13 07:32:27