Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.40 seconds
Igt-Version	IGT-Version: 2.3-gb319fd181 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18118-g7282a0941df7+ x86_64)
Out	Using IGT_SRANDOM=1773153033 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888147add820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.404s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888147add820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.404s)
Dmesg	<6> [70.106685] Console: switching to colour dummy device 80x25 <6> [70.106739] [IGT] kms_pm_rpm: executing <6> [70.108608] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [70.108817] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [70.112894] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [70.112900] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [70.117103] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [70.117490] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [70.117495] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [70.121722] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [70.121954] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [70.121957] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [70.126156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [70.126450] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [70.126453] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [70.130636] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [70.130647] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [70.130650] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [70.134872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [70.134884] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [70.134886] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [70.139111] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [70.139128] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [70.139130] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [70.143310] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [70.143349] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [70.143352] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [70.145380] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.145534] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.145680] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.148261] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [70.148296] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [70.148298] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [70.153127] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [70.256716] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.156090] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.161016] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.162340] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.162618] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.162900] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.163042] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.165278] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.190713] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.197612] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.197761] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.197934] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.198162] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.198366] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.198574] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.198771] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.198949] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.199337] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.199470] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.199760] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.200469] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.201339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.210637] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.211831] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.212065] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [71.214329] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [71.216772] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [71.221745] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.222780] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.224212] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [71.224383] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [71.228578] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [71.247734] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.248079] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.248430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.250012] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.250585] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.255104] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.256471] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.256907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.257203] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.257347] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.259559] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.329785] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [71.341892] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.344722] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.344875] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.345049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.345277] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.345483] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.345695] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.345893] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.346073] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.346313] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.346446] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.346915] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.347606] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.347753] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.353893] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.354013] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.354153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.355123] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.356564] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [71.356754] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [71.360795] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [71.365171] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [71.365281] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [71.382738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.382897] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.383036] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.384303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.384454] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.388008] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.389359] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.389592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.389883] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.390019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.391740] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.478586] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.486835] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.487667] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.488603] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.489543] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.490481] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.491377] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.492303] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.493176] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.494861] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.495656] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.497229] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.499729] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.500485] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.509700] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.509877] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.510272] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [71.512667] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [71.512845] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [71.515128] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [71.520020] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [71.524987] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.525999] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.527440] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [71.527549] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [71.618287] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.619229] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.620058] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.622014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.622851] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.630149] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.631833] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.632832] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.633799] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.634535] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.641075] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.747604] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.756219] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.757055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.758005] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.758975] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.759983] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.760956] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.761903] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.762822] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.763749] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.764556] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.765542] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.768052] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.768707] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.780196] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.780564] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.780699] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.781533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.782854] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [71.782851] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [71.783077] [IGT] kms_pm_rpm: exiting, ret=0 <7> [71.787140] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <6> [71.791589] Console: switching to colour frame buffer device 160x45 <7> [71.791541] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]

Created at 2026-03-11 01:05:50