Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.46 seconds
Igt-Version 
IGT-Version: 2.3-gb319fd181 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18118-g7282a0941df7+ x86_64)
Out 
Using IGT_SRANDOM=1773153053 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811f9b9820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140b/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0xdd/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (11.462s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811f9b9820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b7c/0x26e0
     do_syscall_64+0xdd/0x1470
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.462s)
Dmesg
<6> [87.580467] Console: switching to colour dummy device 80x25
<6> [87.580533] [IGT] kms_pm_rpm: executing
<6> [87.591871] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [87.592170] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [87.595102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [87.595416] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [87.595698] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [87.595978] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [87.596755] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [87.597204] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [87.597210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [87.597392] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [87.601808] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [87.602159] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [87.602163] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [87.602753] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [87.603267] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [87.603847] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [87.604624] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [87.605107] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [87.605709] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [87.606042] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [87.606047] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [87.606490] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.606658] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [87.607057] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.607280] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.607284] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [87.607464] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [87.611629] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.611632] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [87.611813] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [87.612096] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [87.612100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [87.616344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [87.616359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [87.616362] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [87.617100] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [87.617577] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [87.618165] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [87.618179] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [87.618183] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [87.618664] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.618832] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [87.619240] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.619445] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.619448] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [87.619616] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [87.623799] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.623803] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [87.623983] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [87.624033] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [87.624037] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [87.628276] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [87.628314] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [87.628317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [87.629045] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [87.629523] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [87.630119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [87.630156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [87.630159] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [87.630584] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.630759] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [87.631178] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [87.631385] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.631388] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [87.631557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [87.635744] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [87.635747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [87.635926] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [87.707170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [87.707488] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [87.707777] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [87.708094] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [87.708848] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.689525] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.698788] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.722830] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.727749] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.728514] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [98.728497] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.731705] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.756514] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.764994] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.765555] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.766079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.766988] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.768073] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [98.767956] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [98.772529] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [98.773021] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [98.774232] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [98.775132] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [98.776607] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [98.777223] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [98.777524] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [98.778059] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [98.778405] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [98.778412] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [98.778709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [98.783103] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [98.783111] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [98.783741] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [98.785874] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [98.786236] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.786572] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.786926] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.787895] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.788439] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.792788] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.885702] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [98.897891] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.906332] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.906843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.907317] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.909436] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.910483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [98.911015] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [98.915085] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [98.915564] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [98.916787] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [98.917691] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [98.919479] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [98.919414] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [98.920083] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [98.920285] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [98.920676] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [98.920931] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [98.920935] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [98.921117] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [98.925219] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [98.925223] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [98.928849] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [98.929057] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.929245] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.929430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.930120] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.930363] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.933603] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [99.038333] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [99.048411] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [99.048955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.049537] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.050535] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.052527] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<6> [99.054342] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [99.055222] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [99.057216] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [99.057827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [99.059074] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [99.059933] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [99.061137] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [99.061581] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.061771] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.062160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.062380] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.062384] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.062565] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.066727] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.066731] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.067124] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [99.067260] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [99.154962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [99.155445] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.155909] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.156323] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.157270] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.157920] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [99.163784] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [99.282858] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [99.293294] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [99.293888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.294809] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.296056] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.297315] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [99.297411] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<6> [99.297706] [IGT] kms_pm_rpm: exiting, ret=0
<7> [99.301707] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [99.302053] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [99.303016] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [99.303887] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [99.305645] Console: switching to colour frame buffer device 128x48
<7> [99.306032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [99.306518] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.306686] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.307229] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.307538] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.307544] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.307858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.312369] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.312373] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.314876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [99.315096] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.315285] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.315470] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.316167] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-03-11 01:05:50