Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.31 seconds
Igt-Version 
IGT-Version: 2.3-g4626b8c80 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18116-g77e176657e78+ x86_64)
Out 
Using IGT_SRANDOM=1773145154 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888146a51820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.311s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.311s)
Dmesg
<6> [121.930005] Console: switching to colour dummy device 80x25
<6> [121.930108] [IGT] kms_pm_rpm: executing
<7> [121.933898] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [121.939955] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [121.939966] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [121.940372] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [121.941073] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [121.941647] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [121.942316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [121.942815] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [121.943130] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [121.943939] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.945463] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.946981] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.948450] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.950052] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.951739] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.953355] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.954963] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.956399] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.957349] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [121.958019] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [121.958410] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [121.958967] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [121.959697] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [121.959705] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [121.964049] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [121.964677] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [121.964685] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.030262] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.033479] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.033490] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.033903] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.037115] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.037125] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.037531] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [122.038192] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [122.038208] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [122.039061] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.039524] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.040569] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.042380] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.044295] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.046005] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.046346] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.047019] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.047662] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.048256] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.049302] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.049891] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.050798] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.051687] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.052462] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.054067] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.055912] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.057741] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.059486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.061274] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.062332] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.063247] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.063714] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.064493] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [122.064544] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [122.064553] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [122.069018] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [122.069058] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [122.069067] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.134848] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.138136] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.138168] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.138519] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.141757] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.141768] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.142131] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [122.142248] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [122.142262] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [122.143067] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.143549] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.144530] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.146201] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.147881] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.149448] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.151344] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.153073] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.154822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.156527] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.157732] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.158340] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.158872] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.159276] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.160941] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.161694] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.162516] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.163395] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.164478] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.165270] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.165756] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.166600] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [122.166783] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [122.166797] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [122.171487] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [122.171597] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [122.171605] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.237822] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.241605] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.241622] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.242161] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.246247] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.246266] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.246915] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [122.261424] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.262220] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.262874] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.263576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.265340] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.258157] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [123.266517] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [123.290059] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [123.303858] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [123.305955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.307265] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [123.308769] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [123.310287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.312252] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.313891] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.316703] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.317774] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.319590] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.322147] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.325644] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.327759] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.329854] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.331970] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.333983] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.335950] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.337671] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.338745] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.340003] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.341014] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.342880] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [123.347472] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [123.413557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.416890] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.416903] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.417237] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.420510] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.420521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.422141] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [123.422655] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [123.445079] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.445820] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.446484] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.447284] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.448581] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.450711] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [123.462226] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [123.527480] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [123.580584] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [123.591988] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [123.598201] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [123.598895] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.599235] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.599825] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.600588] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [123.600500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [123.600944] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.601713] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.602105] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.602921] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.604442] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.605943] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.607518] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.609090] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.610812] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.612557] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.614144] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.615732] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.616683] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.617678] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.618379] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.619706] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [123.624118] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [123.689917] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.693310] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.693327] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.693677] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.697012] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.697023] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.697698] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [123.725186] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.726090] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.726726] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.727396] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.728764] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.731483] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [123.742872] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [123.812140] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [123.832328] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [123.834421] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.835332] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [123.835316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.836760] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.838920] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [123.840308] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [123.841213] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.842174] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.843883] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.845923] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.847640] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.849445] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.851208] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.853049] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.854865] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.856604] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.858169] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.859228] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.860328] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.861089] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.862282] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [123.866737] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [123.932452] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.935710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.935722] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.936078] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.939455] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.939466] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.940918] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [123.941045] [IGT] kms_pm_rpm: exiting, ret=0
<7> [123.943113] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.943560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.943959] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.944481] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.945503] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.946441] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.946904] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.947745] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [123.948981] Console: switching to colour frame buffer device 128x48
Created at 2026-03-10 21:08:56