Results for igt@kms_frontbuffer_tracking@fbc-1p-primscrn-indfb-pgflip-blt

Result: Pass

git-log-oneline i915_display_info2 igt_runner2 runtimes2 results2.json results2-i915-load.json guc_logs2.tar i915_display_info_post_exec2 boot2 dmesg2

DetailValue
Duration 2.99 seconds
Hostname 
shard-dg1-14
Igt-Version 
IGT-Version: 2.3-geac3b04d1 (x86_64) (Linux: 7.0.0-rc2-CI_DRM_18100-gce63d46cc8fc+ x86_64)
Out 
Using IGT_SRANDOM=1772841367 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test PSR: no usable eDP screen.
Can't test DRRS: no usable screen.
Starting subtest: fbc-1p-primscrn-indfb-pgflip-blt
Subtest fbc-1p-primscrn-indfb-pgflip-blt: SUCCESS (2.991s)
Err 
Starting subtest: fbc-1p-primscrn-indfb-pgflip-blt
Subtest fbc-1p-primscrn-indfb-pgflip-blt: SUCCESS (2.991s)
Dmesg
<6> [400.942623] Console: switching to colour dummy device 80x25
<6> [400.943339] [IGT] kms_frontbuffer_tracking: executing
<7> [400.946615] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [400.947744] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [400.948037] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [400.961281] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [400.961288] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [400.961547] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [400.961717] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [400.962070] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [400.983281] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.004433] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.025576] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.046716] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.067856] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.088997] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.110202] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.131362] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.152518] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.173656] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.194808] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.215960] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.237133] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.258293] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.279445] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.300607] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.321760] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.342913] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.364101] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.385259] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.406411] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.427565] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.448731] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.469885] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.491043] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.512203] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.533366] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.554522] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.575681] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.596834] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.617988] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.639179] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.639369] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [401.639416] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [401.640156] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [401.640161] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [401.644470] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [401.644938] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [401.644943] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [401.649142] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [401.649699] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [401.649704] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [401.653921] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [401.654437] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [401.654442] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [401.658663] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [401.659129] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [401.659134] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [401.663437] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [401.664132] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [401.664136] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [401.685365] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.706490] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.727632] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.748772] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.769912] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.791095] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.812257] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.833411] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.854563] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.875729] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.896889] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.918047] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.939206] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.960364] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [401.981517] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.002670] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.023824] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.044977] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.066167] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.087326] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.108477] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.129631] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.150785] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.171938] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.193121] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.214280] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.235433] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.256584] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.277736] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.298890] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.320042] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.341213] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [402.341397] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [402.341442] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [402.341464] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1]
<7> [402.341470] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:599:HDMI-A-1]
<7> [402.365830] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD monitor FH-DP4K
<7> [402.365851] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD size 36, SAD count 2
<7> [402.366032] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [402.366231] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK on first message, retry
<7> [402.366587] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [402.366760] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [402.366774] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] Assuming DP dual mode adaptor presence based on VBT
<7> [402.366922] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] DP dual mode adaptor (type 1 DVI) detected (max TMDS clock: 165000 kHz)
<7> [402.367734] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1440": 60 241700 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9 (CLOCK_HIGH)
<7> [402.367744] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1600": 60 267820 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9 (CLOCK_HIGH)
<7> [402.367751] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 297000 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [402.367757] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "3840x2160": 30 266640 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9 (CLOCK_HIGH)
<7> [402.367764] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 296703 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [402.367772] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1] probed modes:
<7> [402.367776] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
<7> [402.367780] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 17 151100 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9
<7> [402.367783] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1600": 30 133910 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9
<7> [402.367787] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1440": 30 120850 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9
<7> [402.367790] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x40 0x9
<7> [402.367793] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148352 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [402.367797] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [402.367800] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [402.367804] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [402.367807] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [402.367811] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [402.367814] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [402.367818] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1152x864": 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
<7> [402.367821] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [402.367825] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [402.367828] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
<7> [402.367831] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
<7> [402.367835] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [402.367838] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
<7> [402.367842] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
<7> [402.367845] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [402.367848] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [402.367852] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
<7> [402.367855] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
<7> [402.367859] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
<7> [402.367862] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [402.367895] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [402.367899] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [402.372117] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [402.372134] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [402.372138] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [402.376396] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [402.376413] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [402.376416] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [402.380629] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [402.380645] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [402.380649] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [402.384860] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [402.384877] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [402.384880] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [402.389111] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [402.391330] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [402.391430] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [402.391549] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [402.391669] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [402.391790] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<6> [402.394982] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-indfb-pgflip-blt
<7> [402.395751] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [402.395846] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [402.395962] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [402.396080] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [402.396211] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<7> [402.396828] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [402.442432] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [402.501856] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<7> [402.519053] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [402.519352] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [402.575747] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [402.606545] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [402.619801] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [402.670394] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [402.670781] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [402.703314] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [402.703676] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [402.704004] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [402.737804] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [402.738804] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [402.754960] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:642] from all active usage due to RMFB ioctl
<7> [402.755261] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:642] is removed
<7> [402.755478] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [402.756419] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [402.757331] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [402.758246] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [402.759127] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [402.760124] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [402.761105] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [402.774737] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:634]
<7> [402.775441] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [402.776067] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:645]
<7> [402.776731] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:646]
<7> [402.787405] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [402.788439] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [402.789425] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.304342] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.304541] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.385608] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [403.385693] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [403.385868] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [403.386277] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [403.386671] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [403.387070] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [403.387477] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [403.387921] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [403.388356] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [403.388761] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [403.403307] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.403540] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.403734] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.403954] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.404153] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.411384] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [403.420174] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [403.428961] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [403.487725] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [403.488113] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [403.519367] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.520039] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.520699] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.553942] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.554943] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.569163] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [403.569414] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [403.586513] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [403.587752] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.588779] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.589740] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.593630] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.593812] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.619329] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.619558] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.619755] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.652739] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.653224] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.669179] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [403.669432] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [403.686500] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [403.686485] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.687515] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.688471] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.691650] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.692634] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.720392] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.721429] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.722450] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.753801] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.754823] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.769172] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [403.769429] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [403.786480] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.786592] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [403.787564] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.788543] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.791412] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.792430] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.819343] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.819570] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.819770] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.852825] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.853304] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [403.871934] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:646] from all active usage due to RMFB ioctl
<7> [403.872262] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:646] is removed
<7> [403.872478] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [403.873432] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [403.874346] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [403.875283] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [403.876175] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [403.877307] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [403.878259] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [403.888317] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [403.903374] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [403.904408] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [403.905383] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [403.941224] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [403.941452] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.019007] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [404.019105] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [404.019350] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [404.019788] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [404.020228] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [404.020647] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [404.021061] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [404.021649] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [404.022175] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [404.022721] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [404.026658] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [404.027363] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [404.062579] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [404.076154] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [404.085723] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [404.137210] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.137533] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [404.154326] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.154624] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.154885] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.188178] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.191299] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.192267] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.276096] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.303407] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.304435] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.305419] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.337156] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.338161] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.353127] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [404.370405] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.371442] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.372419] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.410155] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [404.417372] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.417657] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.418602] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [404.437399] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.437602] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.437774] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.464526] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.465258] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.465479] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.540716] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.563369] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.563635] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.563869] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.603892] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.604891] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.619744] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [404.635986] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [404.637002] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.638039] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.639064] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.651341] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.651824] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.668789] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [404.687398] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.688193] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.688999] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.715375] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.718360] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.719345] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.809431] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.810674] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.811715] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.812674] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.815472] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.816821] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.836424] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.837458] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.838447] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.870645] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.871648] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.886630] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [404.902031] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [404.904406] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.905550] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.906519] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.915884] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.916471] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [404.918768] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [404.936360] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [404.936870] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [404.937364] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [404.967983] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [404.970997] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [404.971980] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.059300] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [405.059560] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.060594] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.061553] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.064325] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.065312] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.087412] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.088445] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.089434] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.120563] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.121565] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.136652] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [405.152178] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [405.154399] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.155435] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.156416] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.166282] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.166763] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.168773] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [405.187366] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.187876] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.188370] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.215194] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [405.218258] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.219240] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.306546] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.307577] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.308556] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.309397] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [405.312585] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.313566] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.336422] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.337449] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.338424] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.370564] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.371565] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<6> [405.389300] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-indfb-pgflip-blt, SUCCESS
<7> [405.391015] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:637] from all active usage due to RMFB ioctl
<7> [405.391325] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:637] is removed
<7> [405.391536] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [405.392473] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [405.393382] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [405.394295] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [405.395174] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [405.396181] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [405.397131] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [405.401832] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<6> [405.423710] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [405.426259] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [405.437442] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.438475] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [405.439851] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [405.461409] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [405.462714] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [405.463656] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [405.464576] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [405.465487] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [405.466605] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [405.467568] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [405.468509] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [405.471997] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.472986] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [405.474361] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [405.475328] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [405.485600] i915 0000:03:00.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [405.502188] Console: switching to colour frame buffer device 240x67
Created at 2026-03-07 01:21:46