Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.3-gc807f7fde (x86_64) (Linux: 6.19.0-CI_DRM_18016-gf8bde45966c3+ x86_64)
Out 
Using IGT_SRANDOM=1771733930 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Dmesg
<6> [179.511176] Console: switching to colour dummy device 80x25
<6> [179.511370] [IGT] kms_force_connector_basic: executing
<7> [179.523289] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [179.524690] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [179.548871] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [179.550389] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [179.550399] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.550406] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.554699] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.554722] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.554726] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.558939] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.558971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.558974] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.563201] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [179.563575] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [179.563948] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [179.563953] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.563956] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.622672] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [179.628508] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.628521] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [179.628720] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [179.634147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.634153] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [179.634297] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from disconnected to connected
<7> [179.634345] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [179.634348] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [179.634351] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [179.634354] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [179.634357] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [179.634359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [179.634386] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.634389] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.642590] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [179.643264] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [179.692682] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [179.698254] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.698261] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [179.698388] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [179.703759] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.703764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [179.703924] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [179.703928] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [179.703932] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [179.703934] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [179.703937] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [179.703940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [179.704228] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:528:HDMI-A-1] EDID override set
<7> [179.704244] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.704248] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.704613] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD monitor IGT
<7> [179.704626] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD size 24, SAD count 0
<7> [179.763204] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [179.769152] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [179.769497] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [179.769523] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [179.769536] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [179.769546] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [179.769554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [179.769560] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [179.769566] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [179.769573] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [179.769930] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [179.770397] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.770407] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.833660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [179.839473] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.839505] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [179.839991] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [179.845701] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [179.845710] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [179.845850] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:528:HDMI-A-1] EDID changed, epoch counter 2
<7> [179.845908] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [179.845925] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [179.845941] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [179.845945] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [179.845948] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [179.845951] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [179.845953] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [179.845956] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [179.846096] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [179.846100] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.846103] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.850365] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from connected to disconnected
<7> [179.850393] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.850413] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [179.850515] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [179.850664] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.850676] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.855259] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [179.855449] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [179.855831] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [179.856818] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:507:eDP-1] force updated from 0 to 0 or reprobing
<7> [179.856822] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [179.856826] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [179.857409] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [179.857874] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [179.858003] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.858119] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.858256] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [179.858260] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [179.858262] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [179.858264] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [179.858277] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [179.858396] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [179.858514] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [179.859467] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [179.859471] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [179.859493] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [179.859496] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [179.860101] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [179.860518] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [179.860657] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.860783] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.860924] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [179.860927] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [179.860930] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [179.860932] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [179.860941] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [179.861064] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [179.861180] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [179.861959] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [179.861962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [179.862049] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:507:eDP-1] EDID override reset
<7> [179.862063] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [179.862066] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [179.862703] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [179.863122] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [179.863244] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.863370] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.863508] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [179.863511] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [179.863513] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [179.863515] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [179.863524] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [179.863662] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [179.863782] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [179.864688] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [179.864692] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [179.864781] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:516:DP-1] EDID override reset
<7> [179.864793] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [179.864797] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [179.869019] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [179.869125] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [179.869129] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.869132] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.873337] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.873359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.873362] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.877555] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.877641] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [179.877654] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.877657] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.881872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.881946] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:534:DP-2] EDID override reset
<7> [179.881957] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [179.881961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [179.882222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [179.882284] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:543:DP-3] EDID override reset
<7> [179.882294] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [179.882297] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [179.882530] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [179.882587] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:552:DP-4] EDID override reset
<7> [179.882597] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [179.882600] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [179.882853] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [179.882913] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:561:DP-5] EDID override reset
<7> [179.882923] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [179.882926] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [179.883161] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<6> [179.883563] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [179.883982] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [179.926226] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [179.926236] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [179.926308] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [179.926317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [179.927214] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [179.927909] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [179.928230] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.928519] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [179.928868] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [179.928873] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [179.928876] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [179.928879] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [179.928893] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [179.929078] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [179.929434] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [179.930252] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [179.930257] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [179.930262] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [179.930267] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [179.934506] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [179.934511] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [179.934515] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [179.938755] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [179.938758] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [179.938761] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [179.938995] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [179.938999] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [179.939002] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [179.939247] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [179.939250] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [179.939253] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [179.939478] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [179.939481] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [179.939483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [179.939721] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<7> [179.939724] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] enabled? yes
<7> [179.939727] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:516:DP-1] enabled? no
<7> [179.939730] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:528:HDMI-A-1] enabled? no
<7> [179.939732] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:534:DP-2] enabled? no
<7> [179.939735] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:543:DP-3] enabled? no
<7> [179.939737] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:552:DP-4] enabled? no
<7> [179.939739] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:561:DP-5] enabled? no
<7> [179.939760] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [179.939770] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] found preferred mode: 3840x2400
<7> [179.939773] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [179.939786] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:150:pipe A] desired mode 3840x2400 set (0,0)
<7> [179.942709] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [179.959373] Console: switching to colour frame buffer device 240x75
Created at 2026-02-22 06:36:32