Result:
git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 1.51 seconds |
| Igt-Version |
IGT-Version: 2.3-g066e572f7 (x86_64) (Linux: 6.19.0-CI_DRM_18003-gfc9512d31fa2+ x86_64) |
| Out |
Using IGT_SRANDOM=1771390324 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88814adb1820 has 1/1 users at
track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
__intel_runtime_pm_get+0x60/0x130 [i915]
i915_display_rpm_get_raw+0x17/0x30 [i915]
intel_display_rpm_get_raw+0x20/0x30 [i915]
__intel_display_power_put_async+0x3a/0x1c0 [i915]
intel_atomic_commit_tail+0x140b/0x1d70 [i915]
intel_atomic_commit+0x2e8/0x330 [i915]
drm_atomic_commit+0xaf/0xf0
drm_atomic_helper_set_config+0x82/0xd0
drm_mode_setcrtc+0x407/0xa10
drm_ioctl_kernel+0xb3/0x120
drm_ioctl+0x2d4/0x5a0
__x64_sys_ioctl+0xa5/0x100
x64_sys_call+0x1243/0x26b0
do_syscall_64+0x93/0x1470
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.515s)
|
| Err |
Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (1.515s) |
| Dmesg |
<6> [213.488497] Console: switching to colour dummy device 80x25
<6> [213.489085] [IGT] kms_pm_rpm: executing
<7> [213.492328] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [213.498837] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [213.498849] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [213.503172] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [213.503576] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [213.503583] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [213.503905] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [213.504195] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [213.504617] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [213.504626] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [213.504991] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [213.505387] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [213.505914] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [213.505921] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [213.506568] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [213.507015] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [213.507290] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [213.507506] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [213.507756] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [213.507764] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [213.507768] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [213.507772] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [213.507795] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [213.508016] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [213.508240] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [213.509076] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [213.509084] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [213.509101] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [213.509133] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [213.509139] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [213.513461] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [213.513494] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [213.513501] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [213.513837] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [213.513856] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [213.513861] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [213.514189] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [213.514222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [213.514227] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [213.514814] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [213.515242] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [213.515435] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [213.515628] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [213.515857] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [213.515864] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [213.515868] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [213.515872] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [213.515898] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [213.516127] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [213.516327] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [213.517133] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [213.517140] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [213.517145] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [213.517211] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [213.517218] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [213.521480] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [213.521545] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [213.521550] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [213.521873] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [213.521938] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [213.521943] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [213.522264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [213.522688] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:425]
<7> [214.546249] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [214.547245] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [214.548186] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [214.548168] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [214.549191] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [214.550097] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [214.556814] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [214.557090] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [214.557664] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [214.558197] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [214.558697] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [214.559194] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [214.559693] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [214.560210] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [214.560709] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [214.561260] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [214.561752] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [214.562276] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [214.562760] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [214.563270] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [214.563753] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [214.564279] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [214.564800] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [214.565320] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [214.565814] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [214.566337] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [214.566827] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [214.567347] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [214.567874] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [214.568407] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [214.568913] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [214.569416] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [214.569921] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [214.570449] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [214.570957] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [214.571478] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [214.571986] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [214.572501] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [214.573014] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [214.573533] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [214.574047] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [214.574527] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [214.575041] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [214.575553] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [214.576068] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [214.576567] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [214.576986] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [214.577528] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:150:pipe A] releasing DPLL 0
<7> [214.578176] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [214.578644] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [214.579141] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [214.579597] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [214.580074] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [214.580538] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [214.580991] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [214.581470] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [214.581975] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [214.582454] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [214.582964] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [214.583484] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [214.583975] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [214.584441] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [214.584841] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [214.585355] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [214.585853] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [214.586401] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [214.586877] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [214.587397] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [214.587900] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [214.588392] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: no [modeset]
<7> [214.588851] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [214.589166] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [214.589639] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [214.590118] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [214.590583] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [214.591056] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [214.591570] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [214.592690] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [214.802334] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 0
<7> [214.803387] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [214.809638] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power off
<7> [214.810234] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [214.810796] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [214.865452] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [214.866338] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [214.867079] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [214.867864] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [214.870070] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [214.870627] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [214.870964] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [214.871220] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [214.871446] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [214.871686] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.871989] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [214.872211] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [214.872439] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [214.872647] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [214.872858] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [214.873078] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [214.873289] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [214.873499] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [214.873696] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [214.873890] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [214.874110] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [214.874321] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [214.874681] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [214.874889] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [214.875092] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.875387] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [214.875675] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [214.876200] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [214.876389] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [214.895213] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [214.896088] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.896811] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.897834] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.899636] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.903707] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.905042] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.906104] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.907235] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.908036] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.908561] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.910166] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [214.980813] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [214.997553] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [215.010514] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.010779] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.011086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.011517] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.012314] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [215.013054] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [215.013712] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.015157] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.015677] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.016198] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.018691] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.018921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.023147] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.024213] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [215.024804] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [215.025089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [215.025569] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.026373] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [215.026919] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [215.031368] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [215.031636] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [215.031974] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.032191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.032874] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [215.034252] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [215.034659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.035405] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [215.035604] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [215.035897] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [215.036215] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.036494] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.037238] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [216.082297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.083404] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.084604] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [216.085672] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [216.086510] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [216.087258] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [216.087583] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.087791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.088322] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.089104] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [216.089320] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.090154] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.090881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.091873] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.092536] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.093152] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.093631] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.094172] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.142694] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [216.142829] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:389:eDP-1]
<7> [216.143264] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:389:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [216.144227] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:388:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [216.144904] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [216.145554] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [216.146219] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:388:DDI A/PHY A] [CRTC:150:pipe A]
<7> [216.146729] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [216.147358] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [216.147905] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [216.148447] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [216.148961] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [216.149441] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [216.149905] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [216.150400] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [216.150890] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [216.151413] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [216.151950] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [216.152448] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [216.152957] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [216.153456] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [216.153951] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [216.154462] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [216.154986] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [216.155484] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [216.155978] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [216.156475] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [216.156993] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [216.157497] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [216.158007] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [216.158511] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [216.159009] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [216.159509] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [216.160032] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [216.160538] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [216.161053] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [216.161537] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [216.162040] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [216.162551] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [216.163068] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [216.163574] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [216.164082] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [216.164578] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [216.165103] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [216.165747] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [216.166219] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [216.166752] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [216.167212] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [216.167667] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [216.168149] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [216.168622] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [216.169088] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [216.169591] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [216.170066] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [216.170565] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [216.171080] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [216.171539] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [216.171946] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [216.172389] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [216.172851] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [216.173337] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [216.173839] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [216.174351] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [216.174786] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [216.175278] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [216.175745] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:150:pipe A] allocated DPLL 0
<7> [216.176210] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:150:pipe A] reserving DPLL 0
<7> [216.176613] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [216.177106] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [216.177577] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [216.178064] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [216.178530] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [216.179002] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [216.179412] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [216.179848] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [216.180347] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [216.180819] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [216.181308] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [216.181773] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [216.182280] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [216.182764] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [216.183260] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [216.183766] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [216.184278] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [216.184788] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [216.185334] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [216.185835] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [216.186342] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [216.186824] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [216.187343] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [216.187853] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [216.188374] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [216.188861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [216.189252] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [216.189753] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [216.190295] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [216.190801] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [216.191320] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [216.191764] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [216.192095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [216.192609] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [216.193144] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [216.193641] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [216.194081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [216.194567] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [216.195084] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [216.195590] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.196110] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.196463] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.196667] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [216.196885] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [216.197261] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.197721] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.198185] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [216.198446] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [216.198743] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [216.199201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [FB:425] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [216.199640] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [216.200085] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [216.200448] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [216.200651] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [216.200856] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [216.201077] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [216.201428] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [216.214035] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.214203] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.214400] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.214610] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.214866] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [216.215127] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [216.215386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.215671] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.215903] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.216731] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.218984] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.219199] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.222372] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.222963] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.224571] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.226583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.226992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.227601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [216.227855] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.228159] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [216.228587] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [216.229034] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [216.229408] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [216.229772] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [216.230156] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [216.230512] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [216.230731] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [216.230949] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [216.231341] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [216.231724] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [216.232317] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [216.232712] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [216.233132] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [216.233571] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [216.234020] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [216.234369] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [216.234637] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power on
<7> [216.235042] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [216.235511] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [216.245020] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [216.245354] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power on
<7> [216.245645] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [216.307685] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [216.308533] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [216.309248] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [216.309973] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [216.459364] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [216.460383] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [216.461699] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turning VDD on
<7> [216.462649] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [216.465380] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [216.465411] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [216.465953] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [216.466831] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [216.467096] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [216.467951] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Clock recovery OK
<7> [216.468117] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [216.469427] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [216.469867] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [216.470889] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [216.471707] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [216.472165] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [216.472620] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:389:eDP-1] Performing OUI wait (0 ms)
<7> [216.473486] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 6844
<7> [216.488593] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [216.491659] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [216.492717] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [216.495173] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<6> [216.497710] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [216.500169] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [216.500989] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [216.501645] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [216.503391] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [216.504049] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:425] from all active usage due to RMFB ioctl
<7> [216.504138] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:425] is removed
<7> [216.504241] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [216.504670] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [216.505211] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [216.505653] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [216.506100] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [216.506568] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [216.507051] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [216.507533] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [216.508205] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [216.508696] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [216.509182] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [216.509674] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [216.510192] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [216.510898] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [216.523572] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [216.524142] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [216.524614] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [216.525040] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [216.525515] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [216.526050] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [216.526525] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [216.526971] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [216.527392] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [216.527849] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [216.528330] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [216.528799] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [216.529273] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [216.538541] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [216.540855] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [216.542434] [IGT] kms_pm_rpm: exiting, ret=0
<6> [216.555807] Console: switching to colour frame buffer device 240x67
|