Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.3-g066e572f7 (x86_64) (Linux: 6.19.0-CI_DRM_18003-gfc9512d31fa2+ x86_64)
Out 
Using IGT_SRANDOM=1771390303 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.288s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.288s)
Dmesg
<6> [181.500492] Console: switching to colour dummy device 80x25
<6> [181.500695] [IGT] kms_force_connector_basic: executing
<7> [181.507736] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [181.509134] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [181.525035] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [181.526240] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [181.526249] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.526255] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.530519] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.530545] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.530549] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.534758] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.534794] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.534797] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.539026] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [181.539204] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [181.539485] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [181.539490] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.539493] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.598912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [181.604565] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.604587] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [181.604844] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [181.610275] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.610281] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [181.610431] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from disconnected to connected
<7> [181.610447] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [181.610498] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [181.610537] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [181.610540] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [181.610544] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [181.610546] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [181.610549] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [181.610552] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [181.610580] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.610583] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.669446] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [181.675072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.675082] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [181.675219] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [181.680635] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.680640] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [181.680809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [181.680813] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [181.680816] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [181.680819] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [181.680822] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [181.680824] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [181.681277] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:528:HDMI-A-1] EDID override set
<7> [181.681293] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.681296] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.681689] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD monitor IGT
<7> [181.681692] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:528:HDMI-A-1] ELD size 24, SAD count 0
<7> [181.742446] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [181.748112] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [181.748252] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [181.748263] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [181.748270] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [181.748275] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [181.748280] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [181.748285] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [181.748289] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [181.748294] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [181.748431] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [181.748591] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.748595] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.807440] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [181.813044] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.813052] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [181.813272] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [181.818679] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [181.818683] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [181.818797] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:528:HDMI-A-1] EDID changed, epoch counter 2
<7> [181.818835] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [181.818845] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [181.818851] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] probed modes:
<7> [181.818859] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [181.818862] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [181.818866] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [181.818869] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [181.818872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [181.818995] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [181.818999] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.819002] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.823210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] status updated from connected to disconnected
<7> [181.823216] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.823221] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [181.823257] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [181.823295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.823299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.827547] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<6> [181.827745] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [181.828196] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [181.829308] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:507:eDP-1] force updated from 0 to 0 or reprobing
<7> [181.829313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [181.829317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [181.829952] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [181.830420] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [181.830554] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.830682] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.830835] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [181.830839] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [181.830842] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [181.830844] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [181.830879] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [181.831004] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [181.831126] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [181.831871] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [181.831875] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [181.831897] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [181.831900] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [181.832473] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [181.832898] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [181.833023] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.833143] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.833276] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [181.833279] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [181.833281] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [181.833283] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [181.833293] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [181.833413] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [181.833534] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [181.834247] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [181.834250] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [181.834324] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:507:eDP-1] EDID override reset
<7> [181.834335] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [181.834338] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [181.834896] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [181.835283] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [181.835408] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.835531] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.835662] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [181.835665] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [181.835667] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [181.835669] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [181.835679] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [181.835798] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [181.835938] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [181.836635] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [181.836638] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [181.836713] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:516:DP-1] EDID override reset
<7> [181.836724] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [181.836727] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [181.840950] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [181.841050] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:528:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [181.841053] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.841057] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.845262] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.845282] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.845285] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.849505] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.849568] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:528:HDMI-A-1] EDID override reset
<7> [181.849578] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.849582] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.853779] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.853843] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:534:DP-2] EDID override reset
<7> [181.853861] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [181.853864] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [181.854129] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [181.854193] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:543:DP-3] EDID override reset
<7> [181.854203] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [181.854206] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [181.854445] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [181.854505] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:552:DP-4] EDID override reset
<7> [181.854514] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [181.854517] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [181.854750] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [181.854809] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:561:DP-5] EDID override reset
<7> [181.854818] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [181.854821] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [181.855074] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<6> [181.855480] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [181.855981] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [181.873698] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [181.873703] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [181.873764] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1]
<7> [181.873770] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:507:eDP-1]
<7> [181.874437] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [181.874921] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [181.875056] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.875180] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [181.875317] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [181.875321] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [181.875323] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD monitor
<7> [181.875326] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:507:eDP-1] ELD size 20, SAD count 0
<7> [181.875336] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] VRR capable: yes
<7> [181.875456] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [181.875577] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:507:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [181.876367] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:507:eDP-1] probed modes:
<7> [181.876371] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [181.876376] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1]
<7> [181.876379] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:516:DP-1]
<7> [181.880609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:516:DP-1] disconnected
<7> [181.880614] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1]
<7> [181.880617] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:528:HDMI-A-1]
<7> [181.884833] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:528:HDMI-A-1] disconnected
<7> [181.884838] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2]
<7> [181.884841] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:534:DP-2]
<7> [181.885119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:534:DP-2] disconnected
<7> [181.885123] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3]
<7> [181.885126] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:543:DP-3]
<7> [181.885365] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:543:DP-3] disconnected
<7> [181.885368] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4]
<7> [181.885371] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:552:DP-4]
<7> [181.885619] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:552:DP-4] disconnected
<7> [181.885622] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5]
<7> [181.885624] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:561:DP-5]
<7> [181.885868] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:561:DP-5] disconnected
<7> [181.885871] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] enabled? yes
<7> [181.885875] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:516:DP-1] enabled? no
<7> [181.885878] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:528:HDMI-A-1] enabled? no
<7> [181.885881] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:534:DP-2] enabled? no
<7> [181.885883] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:543:DP-3] enabled? no
<7> [181.885885] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:552:DP-4] enabled? no
<7> [181.885888] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:561:DP-5] enabled? no
<7> [181.885912] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [181.885926] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:507:eDP-1] found preferred mode: 3840x2400
<7> [181.885928] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [181.885953] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:150:pipe A] desired mode 3840x2400 set (0,0)
<7> [181.890211] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [181.906929] Console: switching to colour frame buffer device 240x75
Created at 2026-02-18 09:18:34