Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 1.42 seconds
Igt-Version 
IGT-Version: 2.3-g195f101f2 (x86_64) (Linux: 6.19.0-CI_DRM_17975-gf37b96494b21+ x86_64)
Out 
Using IGT_SRANDOM=1770808789 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881416c1820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140b/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1243/0x26b0
     do_syscall_64+0x93/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (1.415s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881416c1820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b79/0x26b0
     do_syscall_64+0x93/0x1470
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.415s)
Dmesg
<6> [74.054107] Console: switching to colour dummy device 80x25
<6> [74.054158] [IGT] kms_pm_rpm: executing
<6> [74.056006] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [74.056211] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [74.060197] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1]
<7> [74.060204] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<7> [74.064422] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected
<7> [74.064674] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1]
<7> [74.064678] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [74.068880] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected
<7> [74.069147] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2]
<7> [74.069151] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [74.073348] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected
<7> [74.073629] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1]
<7> [74.073633] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<7> [74.077862] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected
<7> [74.077881] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1]
<7> [74.077885] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [74.082107] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected
<7> [74.082119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2]
<7> [74.082123] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [74.086340] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected
<7> [74.086359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1]
<7> [74.086362] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<7> [74.090549] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected
<7> [74.090584] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1]
<7> [74.090587] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [74.094762] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected
<7> [74.094791] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2]
<7> [74.094794] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [74.094985] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [74.095159] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [74.095310] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [74.099111] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected
<7> [74.207168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.101011] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.107039] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.108377] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.108613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.108901] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.109037] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.111054] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.135087] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.141931] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.142123] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.142294] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.142520] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.142721] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.142925] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.143118] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.143293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.143679] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [75.144491] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.145946] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.148119] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.148664] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.157740] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.158955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.159151] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<7> [75.160256] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [75.163981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.165017] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.166429] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [75.166644] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [75.170625] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [75.175067] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [75.194035] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.194188] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.194322] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.195621] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.196193] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.200834] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.202227] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.202463] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.202762] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.202911] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.204945] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.276090] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [75.288110] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.295940] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.296757] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.297658] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.298572] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.299489] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.300393] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.301274] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.302110] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.302993] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [75.303743] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.304723] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.307047] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.307673] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.316680] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.316914] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.317267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.318155] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.319631] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<7> [75.319873] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [75.324022] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [75.324192] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [75.328387] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [75.342065] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.342222] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.342361] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.343625] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.343784] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.349708] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.351121] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.351366] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.351651] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.351785] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.353939] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.437124] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.444940] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.445765] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.446662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.447580] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.448493] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.449393] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.450280] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.451110] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.452696] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [75.453497] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.454958] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.457285] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.457883] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.467006] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.467198] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.468339] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<6> [75.472020] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [75.473386] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [75.473312] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [75.478164] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<7> [75.483123] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.484163] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.485599] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [75.485702] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [75.575164] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.575848] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.576733] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.578775] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.579956] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.588372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.590121] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.591102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.592022] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.592798] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.597932] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.704486] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.712936] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.713764] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.714712] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.715652] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.716628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.717633] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.718564] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [75.719431] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.720379] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [75.721170] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.722148] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.724639] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.725226] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.737862] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.738041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.738223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.739086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.740675] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [75.740768] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1]
<6> [75.741019] [IGT] kms_pm_rpm: exiting, ret=0
<7> [75.745011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1]
<7> [75.749439] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]
<6> [75.749637] Console: switching to colour frame buffer device 160x45
Created at 2026-02-11 19:53:08