Result:
git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 1.52 seconds |
| Igt-Version |
IGT-Version: 2.3-g030b8e426 (x86_64) (Linux: 6.19.0-CI_DRM_17959-gc28055bfac6a+ x86_64) |
| Out |
Using IGT_SRANDOM=1770638586 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888148855820 has 1/1 users at
track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
__intel_runtime_pm_get+0x60/0x130 [i915]
i915_display_rpm_get_raw+0x17/0x30 [i915]
intel_display_rpm_get_raw+0x20/0x30 [i915]
__intel_display_power_put_async+0x3a/0x1c0 [i915]
intel_atomic_commit_tail+0x140b/0x1d70 [i915]
intel_atomic_commit+0x2e8/0x330 [i915]
drm_atomic_commit+0xaf/0xf0
drm_atomic_helper_set_config+0x82/0xd0
drm_mode_setcrtc+0x407/0xa10
drm_ioctl_kernel+0xb3/0x120
drm_ioctl+0x2d4/0x5a0
__x64_sys_ioctl+0xa5/0x100
x64_sys_call+0x1243/0x26b0
do_syscall_64+0x93/0x1470
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.518s)
|
| Err |
Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (1.518s) |
| Dmesg |
<6> [218.779553] Console: switching to colour dummy device 80x25
<6> [218.780211] [IGT] kms_pm_rpm: executing
<7> [218.784591] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [218.790913] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.790926] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.795238] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.795645] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.795652] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.795990] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [218.796553] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.797381] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.797394] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.797961] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [218.798398] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.799347] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [218.799360] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [218.800259] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [218.800977] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [218.801371] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [218.801749] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [218.802099] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [218.802112] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [218.802120] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [218.802126] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [218.802163] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [218.802548] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [218.802987] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [218.804263] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [218.804277] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [218.804287] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [218.804333] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.804344] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.808845] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.808874] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.808879] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.809266] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.809288] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.809299] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.809971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.810044] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [218.810055] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [218.811012] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [218.811652] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [218.812100] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [218.812518] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [218.812991] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [218.813004] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [218.813012] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [218.813019] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [218.813055] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [218.813398] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [218.813722] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [218.815107] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [218.815121] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [218.815132] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [218.815248] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.815259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.819788] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.819846] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.819851] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.820191] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.820281] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.820291] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.820874] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.821585] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:425]
<7> [219.855267] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [219.855471] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [219.855997] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [219.856455] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [219.856911] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [219.857354] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [219.857880] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [219.858324] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [219.858795] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [219.859271] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [219.859700] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [219.860140] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [219.860610] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [219.861111] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [219.861571] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [219.862068] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [219.862529] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [219.862779] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [219.863012] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [219.863324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [219.863495] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [219.864019] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [219.864552] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [219.865121] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [219.865508] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [219.865656] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [219.865903] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [219.866179] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [219.866479] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [219.866682] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [219.867051] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [219.867198] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [219.867713] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [219.868233] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [219.868746] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [219.869257] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [219.869780] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [219.870286] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [219.870788] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [219.871281] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [219.871785] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [219.872308] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [219.872857] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [219.873395] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [219.873912] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [219.874416] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [219.874917] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [219.875424] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:150:pipe A] releasing DPLL 0
<7> [219.876176] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [219.876652] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [219.877424] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [219.877931] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [219.878403] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [219.878882] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.879337] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.879806] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.880526] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [219.881069] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [219.881576] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [219.882114] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [219.882627] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [219.883141] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [219.883637] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [219.884158] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [219.885029] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [219.885591] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [219.886230] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [219.886739] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [219.887208] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [219.887693] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: no [modeset]
<7> [219.888188] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [219.888626] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [219.889012] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [219.889244] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [219.889562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [219.890006] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [219.890559] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [219.891942] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [220.099943] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 0
<7> [220.100953] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [220.109356] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power off
<7> [220.109647] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x00000089, pins 0x00000010, long 0x00000000
<7> [220.110030] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [220.110270] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - short
<7> [220.110612] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [220.165270] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [220.166153] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [220.166899] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [220.171793] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [220.172304] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [220.172879] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [220.172883] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [220.173384] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [220.173456] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [220.174031] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [220.174582] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [220.175209] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [220.175708] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [220.176233] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [220.176733] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [220.177199] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [220.177692] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [220.178161] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [220.178597] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [220.179070] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [220.179523] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [220.180008] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [220.180480] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [220.181356] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [220.181850] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [220.182295] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [220.182910] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [220.183518] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [220.184471] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [220.184830] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [220.203051] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [220.203895] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.204616] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.205670] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [220.207963] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [220.210942] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [220.212201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.213214] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [220.214192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [220.214986] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [220.215504] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [220.216947] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [220.291277] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [220.308345] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [220.321178] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [220.321434] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [220.321725] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [220.322162] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [220.323063] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [220.323792] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [220.324407] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [220.325609] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [220.326170] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [220.326611] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [220.329989] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.330200] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.334392] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [220.335453] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [220.335722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [220.336244] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [220.336858] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.337592] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [220.337996] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [220.342445] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [220.342747] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [220.343085] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.343280] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.343890] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [220.344853] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [220.345508] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [220.346225] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [220.346749] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.347451] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [220.365966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [220.366536] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.367043] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [221.395860] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [221.396977] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [221.398169] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [221.399052] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [221.399069] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [221.399845] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [221.400533] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [221.401125] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [221.401666] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [221.402354] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [221.402342] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [221.403473] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [221.404108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [221.404952] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [221.406091] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [221.406745] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [221.407225] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [221.407772] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [221.452352] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [221.452601] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:389:eDP-1]
<7> [221.452960] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:389:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [221.453872] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:388:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [221.454514] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 link rate required 2019750 available 2160000
<7> [221.455076] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [221.455696] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:388:DDI A/PHY A] [CRTC:150:pipe A]
<7> [221.456190] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [221.456736] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [221.457219] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [221.457705] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [221.458188] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [221.458718] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [221.459221] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [221.459761] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [221.460217] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [221.460702] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [221.461195] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [221.461713] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [221.462224] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [221.462748] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [221.463244] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [221.463747] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [221.464248] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [221.464778] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [221.465289] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [221.465800] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [221.466298] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [221.466806] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [221.467305] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [221.467836] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [221.468354] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [221.468868] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [221.469366] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [221.469871] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [221.470373] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [221.470908] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [221.471408] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [221.471932] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [221.472421] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [221.472952] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [221.473477] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [221.473974] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [221.474485] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [221.475193] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [221.475741] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [221.476315] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [221.476835] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [221.477311] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [221.477839] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [221.478318] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [221.478830] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [221.479376] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [221.479919] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [221.480385] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [221.480891] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [221.481407] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [221.481916] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [221.482381] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [221.482846] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [221.483323] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [221.483871] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [221.484399] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [221.484874] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [221.485329] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [221.485824] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:150:pipe A] allocated DPLL 0
<7> [221.486303] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:150:pipe A] reserving DPLL 0
<7> [221.486794] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [221.487260] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [221.487732] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [221.488192] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [221.488681] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [221.489161] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [221.489649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [221.490106] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [221.490564] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [221.491037] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [221.491527] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [221.491999] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [221.492404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [221.492889] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [221.493367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [221.493861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [221.494324] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [221.494780] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [221.495190] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [221.495681] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [221.496151] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [221.496625] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [221.497081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [221.497507] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [221.497978] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [221.498457] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [221.498931] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [221.499390] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [221.499657] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [221.500003] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [221.500507] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [221.500986] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [221.501466] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [221.501883] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [221.502091] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [221.502334] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [221.502828] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [221.503294] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [221.503763] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [221.504057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.504268] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.504722] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.505187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [221.505662] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [221.506118] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.506441] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.506669] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [221.507090] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [221.507585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [221.508046] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [FB:425] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [221.508508] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [221.508929] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [221.509279] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [221.509771] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [221.510241] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [221.510717] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [221.511182] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [221.523534] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [221.523708] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [221.523903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [221.524114] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [221.524370] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [221.524635] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [221.524901] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [221.525190] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [221.525419] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [221.525712] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [221.528066] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [221.528303] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [221.531593] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [221.532159] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [221.533659] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [221.535616] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [221.536034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [221.536672] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [221.537045] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [221.537335] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [221.537823] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [221.538225] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [221.538623] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [221.539006] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [221.539275] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [221.539485] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [221.539733] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [221.540122] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [221.540535] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [221.540918] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [221.541267] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [221.541698] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [221.542109] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [221.542578] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [221.543015] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [221.543245] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [221.543533] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power on
<7> [221.543788] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [221.544253] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [221.554565] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [221.554982] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power on
<7> [221.555273] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [221.617343] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [221.618240] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [221.619044] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [221.619913] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [221.770553] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [221.771647] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [221.773011] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turning VDD on
<7> [221.773943] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [221.776484] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [221.776523] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [221.777045] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [221.777934] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [221.778193] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [221.779123] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Clock recovery OK
<7> [221.779589] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [221.781320] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [221.781768] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [221.782702] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [221.783496] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [221.783916] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [221.784359] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:389:eDP-1] Performing OUI wait (0 ms)
<7> [221.785267] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 6844
<7> [221.800617] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [221.803688] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [221.804636] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [221.806999] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<6> [221.810800] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [221.811802] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [221.812645] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [221.813365] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:425] from all active usage due to RMFB ioctl
<7> [221.813258] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [221.814069] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [221.814839] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:425] is removed
<7> [221.814967] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [221.815489] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [221.815970] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.816518] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.816979] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.817510] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [221.817994] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [221.818676] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [221.819181] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [221.819686] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [221.820175] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [221.820581] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [221.821048] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [221.821788] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [221.835167] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [221.835858] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [221.836440] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [221.836986] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [221.837646] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [221.838199] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [221.838735] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [221.839232] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [221.839746] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [221.840259] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [221.840812] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [221.841316] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [221.841827] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [221.850335] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [221.852605] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [221.853825] [IGT] kms_pm_rpm: exiting, ret=0
<6> [221.867789] Console: switching to colour frame buffer device 240x67
|