igt@kms_frontbuffer_tracking@basic on bat-jsl-1@IGT

Detail	Value
Duration	4.05 seconds
Igt-Version	IGT-Version: 2.3-g6a10d1136 (x86_64) (Linux: 6.19.0-rc7-CI_DRM_17902-g6a3c9a03d943+ x86_64)
Out	Using IGT_SRANDOM=1769664220 for randomisation Opened device: /dev/dri/card0 FBC last action not supported Can't test DRRS: no usable screen. Starting subtest: basic Subtest basic: SUCCESS (4.048s)
Err	Starting subtest: basic Subtest basic: SUCCESS (4.048s)
Dmesg	<6> [246.138931] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4 <4> [246.138953] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID) <4> [246.138960] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000 <4> [246.138966] pcieport 0000:00:1c.4: [ 0] RxErr (First) <6> [246.174556] Console: switching to colour dummy device 80x25 <6> [246.175122] [IGT] kms_frontbuffer_tracking: executing <7> [246.182241] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [246.184398] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [246.185436] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [246.204480] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] <7> [246.204506] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:278:DP-1] <7> [246.209177] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] disconnected <7> [246.210567] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] <7> [246.210590] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:287:HDMI-A-1] <7> [246.215344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] disconnected <7> [246.216456] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] <7> [246.216475] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:293:HDMI-A-2] <7> [246.221223] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] disconnected <7> [246.222821] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:269:eDP-1] <7> [246.222843] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:269:eDP-1] <7> [246.223530] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [246.224068] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [246.224622] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [246.225225] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [246.225243] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] ELD monitor <7> [246.225253] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] ELD size 20, SAD count 0 <7> [246.225307] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] VRR capable: no <7> [246.225893] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [246.226440] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [246.228124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:269:eDP-1] probed modes: <7> [246.228143] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [246.228156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa <7> [246.228222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] <7> [246.228236] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:278:DP-1] <7> [246.232940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] disconnected <7> [246.233027] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] <7> [246.233044] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:287:HDMI-A-1] <7> [246.237988] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] disconnected <7> [246.238061] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] <7> [246.238076] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:293:HDMI-A-2] <7> [246.242833] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] disconnected <7> [246.247330] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:299] <7> [246.247578] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:300] <7> [246.247858] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:301] <7> [246.248129] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:302] <7> [246.248474] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:303] <6> [246.256425] [IGT] kms_frontbuffer_tracking: starting subtest basic <7> [246.257242] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [246.269137] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:299] <7> [246.269615] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:300] <7> [246.270031] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:301] <7> [246.270430] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:302] <7> [246.270796] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:303] <7> [246.272091] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304] <6> [246.320504] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4 <4> [246.320521] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID) <4> [246.320526] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000 <4> [246.320531] pcieport 0000:00:1c.4: [ 0] RxErr (First) <7> [246.388518] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [246.388685] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [246.444069] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B] <7> [246.456261] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C] <7> [246.489910] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [246.490838] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <6> [246.495921] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4 <4> [246.495937] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID) <4> [246.495943] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000 <4> [246.495948] pcieport 0000:00:1c.4: [ 0] RxErr (First) <7> [246.573499] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:304] from all active usage due to RMFB ioctl <7> [246.573669] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:304] is removed <7> [246.573867] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0 <7> [246.574808] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [246.575724] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.576620] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.577556] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.578555] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0 <7> [246.579488] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [246.580423] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0 <7> [246.581348] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0 <7> [246.587711] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A] <7> [246.605804] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:270] <7> [246.606407] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304] <7> [246.606961] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:307] <7> [246.607561] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:308] <7> [248.005889] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [248.006040] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [248.006461] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969 <7> [248.007437] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm <7> [248.008337] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 <7> [248.009194] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 <7> [248.010123] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 <7> [248.011109] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1 <7> [248.012015] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [248.012607] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446 <7> [248.013147] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446 <7> [248.018472] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [248.019054] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A] <7> [248.033453] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B] <7> [248.045967] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C] <7> [248.090722] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.091732] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.172039] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [248.172205] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [248.189255] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.272059] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [248.272226] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [248.288999] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.371956] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [248.372124] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [248.389021] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.473869] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:308] from all active usage due to RMFB ioctl <7> [248.474049] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:308] is removed <7> [248.474257] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0 <7> [248.475234] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [248.476167] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [248.477091] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [248.478095] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [248.479067] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0 <7> [248.480056] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [248.480993] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0 <7> [248.481910] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0 <7> [248.487747] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A] <7> [248.605811] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A] <7> [248.605964] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1] <7> [248.606380] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969 <7> [248.607355] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm <7> [248.608215] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 <7> [248.609091] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 <7> [248.610045] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 <7> [248.611005] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1 <7> [248.611937] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [248.612872] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446 <7> [248.613787] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446 <7> [248.620913] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [248.621586] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A] <7> [248.655103] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B] <7> [248.668104] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C] <7> [248.707467] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.708433] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [248.709264] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.773664] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:268:DDI A/PHY A] PPS 0 turning VDD off <7> [248.774713] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:268:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [248.788895] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.822497] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [248.823511] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [248.824450] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [248.855458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [248.856448] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [248.872406] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304] <7> [248.879295] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [248.880656] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [248.906685] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [248.907776] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [248.908717] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [248.938787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [248.939795] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [248.955779] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <6> [248.959923] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4 <4> [248.959948] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID) <4> [248.959959] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000 <4> [248.959970] pcieport 0000:00:1c.4: [ 0] RxErr (First) <7> [248.988434] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [248.989420] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [248.990338] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.022043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.023098] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.043229] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [249.044567] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.072575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.073646] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.074599] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.105152] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.106183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.122146] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.156643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.157774] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.158718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.188788] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.189800] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.209956] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [249.219884] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.255688] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.256740] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.257681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.288743] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.289751] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.305346] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.338468] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.339469] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.340400] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.371980] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.372989] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.405393] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.405944] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.406451] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.509185] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [249.509872] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.510883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.511516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.538464] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.538914] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.539363] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.572049] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.573111] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.588900] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.622603] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.623661] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.624622] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.655466] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.656456] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.689440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.690127] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.690713] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.714925] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.715706] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.721448] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [249.722107] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.805906] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.839504] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.840516] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.841439] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.871854] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.872839] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.901490] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [249.905647] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.906175] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.906669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.909827] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [249.910880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.911519] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.938586] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [249.939674] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [249.940627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [249.972034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [249.973092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [249.989032] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [250.022653] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.023746] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.024692] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.055469] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [250.056463] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.090355] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.091012] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [250.091187] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.091954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.101829] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [250.102866] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [250.103477] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.189207] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A <7> [250.222448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.223461] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.224389] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.255193] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [250.256286] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.271985] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:304] from all active usage due to RMFB ioctl <7> [250.272163] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:304] is removed <7> [250.272479] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0 <7> [250.273450] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [250.274348] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [250.275214] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [250.276082] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [250.277142] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0 <7> [250.278091] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [250.279010] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0 <7> [250.279924] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0 <7> [250.287756] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A] <6> [250.306574] [IGT] kms_frontbuffer_tracking: finished subtest basic, SUCCESS <6> [250.309691] [IGT] kms_frontbuffer_tracking: exiting, ret=0 <7> [250.311686] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [250.315015] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969 <7> [250.316438] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm, swm, stwm <7> [250.317367] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 <7> [250.318569] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 <7> [250.319501] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 <7> [250.320522] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1 <7> [250.321681] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [250.322627] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446 <7> [250.322711] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.323605] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446 <7> [250.323684] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.324618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.326111] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [250.327141] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.328432] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [250.329337] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A] <7> [250.338810] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [250.355916] Console: switching to colour frame buffer device 200x56 <7> [250.389450] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.390456] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.391423] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<6> [246.138931] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4

<4> [246.138953] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID)

<4> [246.138960] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000

<4> [246.138966] pcieport 0000:00:1c.4: [ 0] RxErr (First)

<6> [246.174556] Console: switching to colour dummy device 80x25

<6> [246.175122] [IGT] kms_frontbuffer_tracking: executing

<7> [246.182241] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [246.184398] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

<7> [246.185436] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [246.204480] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1]

<7> [246.204506] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:278:DP-1]

<7> [246.209177] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] disconnected

<7> [246.210567] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1]

<7> [246.210590] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:287:HDMI-A-1]

<7> [246.215344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] disconnected

<7> [246.216456] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2]

<7> [246.216475] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:293:HDMI-A-2]

<7> [246.221223] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] disconnected

<7> [246.222821] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:269:eDP-1]

<7> [246.222843] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:269:eDP-1]

<7> [246.223530] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [246.224068] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [246.224622] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [246.225225] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [246.225243] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] ELD monitor

<7> [246.225253] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:269:eDP-1] ELD size 20, SAD count 0

<7> [246.225307] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] VRR capable: no

<7> [246.225893] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [246.226440] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:269:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [246.228124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:269:eDP-1] probed modes:

<7> [246.228143] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [246.228156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa

<7> [246.228222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1]

<7> [246.228236] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:278:DP-1]

<7> [246.232940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:278:DP-1] disconnected

<7> [246.233027] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1]

<7> [246.233044] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:287:HDMI-A-1]

<7> [246.237988] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:287:HDMI-A-1] disconnected

<7> [246.238061] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2]

<7> [246.238076] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:293:HDMI-A-2]

<7> [246.242833] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:293:HDMI-A-2] disconnected

<7> [246.247330] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:299]

<7> [246.247578] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:300]

<7> [246.247858] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:301]

<7> [246.248129] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:302]

<7> [246.248474] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:303]

<6> [246.256425] [IGT] kms_frontbuffer_tracking: starting subtest basic

<7> [246.257242] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [246.269137] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:299]

<7> [246.269615] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:300]

<7> [246.270031] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:301]

<7> [246.270430] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:302]

<7> [246.270796] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:303]

<7> [246.272091] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304]

<6> [246.320504] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4

<4> [246.320521] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID)

<4> [246.320526] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000

<4> [246.320531] pcieport 0000:00:1c.4: [ 0] RxErr (First)

<7> [246.388518] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [246.388685] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [246.444069] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B]

<7> [246.456261] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C]

<7> [246.489910] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [246.490838] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<6> [246.495921] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4

<4> [246.495937] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID)

<4> [246.495943] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000

<4> [246.495948] pcieport 0000:00:1c.4: [ 0] RxErr (First)

<7> [246.573499] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:304] from all active usage due to RMFB ioctl

<7> [246.573669] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:304] is removed

<7> [246.573867] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0

<7> [246.574808] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [246.575724] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.576620] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.577556] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.578555] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0

<7> [246.579488] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [246.580423] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0

<7> [246.581348] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0

<7> [246.587711] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]

<7> [246.605804] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:270]

<7> [246.606407] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304]

<7> [246.606961] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:307]

<7> [246.607561] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:308]

<7> [248.005889] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [248.006040] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [248.006461] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969

<7> [248.007437] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm

<7> [248.008337] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0

<7> [248.009194] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0

<7> [248.010123] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0

<7> [248.011109] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1

<7> [248.012015] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [248.012607] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446

<7> [248.013147] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446

<7> [248.018472] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [248.019054] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]

<7> [248.033453] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B]

<7> [248.045967] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C]

<7> [248.090722] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.091732] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.172039] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [248.172205] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [248.189255] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.272059] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [248.272226] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [248.288999] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.371956] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [248.372124] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [248.389021] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.473869] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:308] from all active usage due to RMFB ioctl

<7> [248.474049] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:308] is removed

<7> [248.474257] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0

<7> [248.475234] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [248.476167] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [248.477091] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [248.478095] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [248.479067] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0

<7> [248.480056] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [248.480993] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0

<7> [248.481910] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0

<7> [248.487747] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]

<7> [248.605811] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:110:pipe A]

<7> [248.605964] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:269:eDP-1]

<7> [248.606380] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969

<7> [248.607355] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm

<7> [248.608215] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0

<7> [248.609091] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0

<7> [248.610045] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0

<7> [248.611005] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1

<7> [248.611937] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [248.612872] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446

<7> [248.613787] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446

<7> [248.620913] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [248.621586] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]

<7> [248.655103] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:188:pipe B]

<7> [248.668104] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:266:pipe C]

<7> [248.707467] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.708433] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [248.709264] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.773664] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:268:DDI A/PHY A] PPS 0 turning VDD off

<7> [248.774713] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:268:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [248.788895] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.822497] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [248.823511] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [248.824450] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [248.855458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [248.856448] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [248.872406] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:304]

<7> [248.879295] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [248.880656] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [248.906685] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [248.907776] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [248.908717] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [248.938787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [248.939795] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [248.955779] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<6> [248.959923] pcieport 0000:00:1c.4: AER: Correctable error message received from 0000:00:1c.4

<4> [248.959948] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID)

<4> [248.959959] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000

<4> [248.959970] pcieport 0000:00:1c.4: [ 0] RxErr (First)

<7> [248.988434] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [248.989420] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [248.990338] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.022043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.023098] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.043229] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [249.044567] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.072575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.073646] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.074599] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.105152] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.106183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.122146] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.156643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.157774] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.158718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.188788] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.189800] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.209956] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [249.219884] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.255688] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.256740] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.257681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.288743] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.289751] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.305346] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.338468] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.339469] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.340400] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.371980] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.372989] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.405393] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.405944] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.406451] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.509185] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [249.509872] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.510883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.511516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.538464] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.538914] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.539363] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.572049] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.573111] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.588900] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.622603] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.623661] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.624622] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.655466] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.656456] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.689440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.690127] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.690713] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.714925] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.715706] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.721448] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [249.722107] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.805906] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.839504] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.840516] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.841439] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.871854] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.872839] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.901490] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [249.905647] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.906175] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.906669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.909827] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [249.910880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.911519] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.938586] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [249.939674] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [249.940627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [249.972034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [249.973092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [249.989032] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [250.022653] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.023746] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.024692] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.055469] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [250.056463] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.090355] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.091012] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [250.091187] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.091954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.101829] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [250.102866] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [250.103477] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.189207] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A

<7> [250.222448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.223461] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.224389] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.255193] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [250.256286] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.271985] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:304] from all active usage due to RMFB ioctl

<7> [250.272163] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:304] is removed

<7> [250.272479] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 969) -> ( 0 - 0), size 969 -> 0

<7> [250.273450] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [250.274348] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [250.275214] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [250.276082] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [250.277142] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 0 num active planes 0

<7> [250.278091] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [250.279010] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 0

<7> [250.279924] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 0

<7> [250.287756] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]

<6> [250.306574] [IGT] kms_frontbuffer_tracking: finished subtest basic, SUCCESS

<6> [250.309691] [IGT] kms_frontbuffer_tracking: exiting, ret=0

<7> [250.311686] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

<7> [250.315015] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 969), size 0 -> 969

<7> [250.316438] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm, swm, stwm

<7> [250.317367] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 3, 3, 4, 9, 15, 16, 0, 0, 0

<7> [250.318569] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 79, 79, 105, 235, 391, 417, 40, 0, 0

<7> [250.319501] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 88, 88, 117, 260, 432, 460, 41, 0, 0

<7> [250.320522] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:110:pipe A] data rate 1445240 num active planes 1

<7> [250.321681] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [250.322627] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 21483 required 1446

<7> [250.322711] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.323605] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 23719 required 1446

<7> [250.323684] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.324618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.326111] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [250.327141] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.328432] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [250.329337] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]

<7> [250.338810] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<6> [250.355916] Console: switching to colour frame buffer device 200x56

<7> [250.389450] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.390456] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.391423] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

Results for igt@kms_frontbuffer_tracking@basic