Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.18 seconds
Igt-Version 
IGT-Version: 2.3-g7b26f6089 (x86_64) (Linux: 6.19.0-rc5-CI_DRM_17819-gd5b0278e4bea+ x86_64)
Out 
Using IGT_SRANDOM=1768390660 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88813fdcd818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x960 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.184s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.184s)
Dmesg
<7> [74.709564] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [74.709832] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [74.710034] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [74.710233] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [74.710889] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [74.711045] Console: switching to colour dummy device 80x25
<6> [74.711109] [IGT] kms_pm_rpm: executing
<7> [74.719147] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [74.722832] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [74.722839] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [74.723028] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.727423] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [74.727804] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [74.727809] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [74.728386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [74.728931] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [74.729482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [74.730135] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.730593] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.731176] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [74.731505] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [74.731511] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [74.731954] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.732124] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.732604] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.732812] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.732816] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.732985] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.737122] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.737127] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.737304] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [74.737616] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [74.737622] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [74.741887] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [74.741903] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [74.741907] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [74.742621] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.743094] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.743675] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [74.743690] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [74.743694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [74.744129] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.744295] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.744734] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.744930] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.744934] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.745098] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.749319] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.749323] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.749546] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [74.749569] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [74.749573] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [74.753832] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [74.753873] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [74.753877] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [74.754598] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.755091] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.755736] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [74.755777] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [74.755781] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [74.756224] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.756391] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.756843] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.757045] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.757049] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.757212] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.761399] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.761404] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.761630] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [74.829616] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [74.830048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [74.830464] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [74.830855] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [74.831708] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [85.802094] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [85.811786] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [85.836438] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [85.843961] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [85.845034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [85.845587] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [85.845430] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [85.850162] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [85.850854] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [85.851478] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [85.852048] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [85.853229] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [85.854010] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [85.855211] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [85.855696] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.855866] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [85.856236] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.856490] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.856509] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [85.856687] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [85.860967] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.860971] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [85.861319] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [85.861529] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [85.958452] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [85.958864] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [85.959245] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [85.959642] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [85.960566] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [85.961577] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [85.968004] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [86.063796] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [86.084353] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [86.096337] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [86.104934] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [86.105405] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [86.105839] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [86.106551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [86.107759] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [86.108259] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [86.112941] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [86.113435] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [86.113816] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [86.114650] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [86.115570] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [86.117360] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [86.117933] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.118297] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [86.118913] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.119213] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.119219] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [86.119397] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [86.123559] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.123564] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [86.130327] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [86.130531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [86.130718] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [86.130901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [86.131564] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [86.131836] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [86.135204] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [86.229343] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [86.240587] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [86.241353] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [86.242100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [86.243640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [86.245615] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [86.247954] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<6> [86.248844] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [86.248680] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [86.250190] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [86.251242] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [86.252572] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [86.253018] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.253212] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [86.253606] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.253854] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.253860] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [86.254074] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [86.258270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.258279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [86.258807] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [86.258956] [IGT] kms_pm_rpm: exiting, ret=0
<6> [86.260342] Console: switching to colour frame buffer device 128x48
Created at 2026-01-14 17:50:57