Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.51 seconds
Igt-Version 
IGT-Version: 2.3-ge566d96a2 (x86_64) (Linux: 6.19.0-rc4-CI_DRM_17773-g3d6700a02638+ x86_64)
Out 
Using IGT_SRANDOM=1767726250 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881486fd818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x960 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.513s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881486fd818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b79/0x26b0
     do_syscall_64+0x93/0x1470
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.513s)
Dmesg
<6> [91.067414] Console: switching to colour dummy device 80x25
<6> [91.067481] [IGT] kms_pm_rpm: executing
<6> [91.077277] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [91.077699] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [91.081754] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [91.081762] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.082412] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.082664] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.082878] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.083094] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.086031] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [91.086607] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [91.086614] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [91.087843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.088446] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.089052] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.090021] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.090564] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.091259] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [91.091838] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [91.091845] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [91.092447] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.092707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.093169] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.093500] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.093506] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.093752] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.098162] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.098168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.098485] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [91.098905] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [91.098912] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.103193] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [91.103217] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [91.103223] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [91.104143] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.104682] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.105390] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [91.105413] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [91.105420] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [91.105956] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.106206] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.106721] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.107008] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.107013] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.107259] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.111672] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.111678] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.111950] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [91.111985] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [91.111991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.116403] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [91.116467] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [91.116473] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [91.117350] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.117902] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.118637] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [91.118700] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [91.118706] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [91.119225] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.119526] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.119985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.120283] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.120295] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.120573] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.124983] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.124990] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.125262] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [91.194239] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.194621] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.194924] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.195223] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.196027] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.175037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.183440] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.208077] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.215896] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.216677] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [102.217235] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [102.218012] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [102.222135] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [102.223085] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [102.223736] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [102.224424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [102.225840] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [102.226697] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [102.228174] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [102.228137] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [102.228646] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.228815] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.229187] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.229482] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.229489] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.229680] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.233853] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.233858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.234208] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [102.329514] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.329992] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.330413] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [102.330817] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [102.331663] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.332085] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.337380] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.435855] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [102.448307] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.456912] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.457077] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [102.457290] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [102.457833] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [102.458790] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [102.459017] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [102.463519] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [102.463671] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [102.464000] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [102.464971] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [102.465776] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [102.466979] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [102.467420] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.467616] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.468002] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.468204] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.468209] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.468428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.472631] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.472636] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.481448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.481650] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.481834] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [102.482014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [102.482679] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.482898] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.486372] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.576503] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.586419] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.586940] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [102.587554] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [102.588101] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [102.589069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [102.590746] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [102.591180] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [102.594110] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [102.594657] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [102.595902] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [102.596737] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [102.598162] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [102.598120] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [102.598591] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.598772] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.599223] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.599519] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.599526] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.599720] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.603804] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.603810] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.604150] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [102.697421] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.697738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.697992] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [102.698237] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [102.698923] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.699365] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.702330] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.818455] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.826595] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.827064] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [102.827560] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [102.828454] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [102.829989] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [102.830184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<6> [102.831188] [IGT] kms_pm_rpm: exiting, ret=0
<6> [102.835477] Console: switching to colour frame buffer device 128x48
<7> [102.835276] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [102.835964] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [102.837162] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [102.838064] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [102.839520] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [102.840107] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.840495] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.840998] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.841241] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.841246] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.841436] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.845616] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.845621] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.853445] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.853662] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.853845] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
Created at 2026-01-06 22:45:46