Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.93 seconds
Igt-Version	IGT-Version: 2.3-g906681747 (x86_64) (Linux: 6.19.0-rc1-CI_DRM_17693-g72428bdb20b6+ x86_64)
Out	Using IGT_SRANDOM=1765909270 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 2 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88813f2c1818 has 1/2 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_dp_aux_xfer+0x684/0x960 [i915] intel_dp_aux_transfer+0xd4/0x330 [i915] drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper] drm_dp_dpcd_read+0x87/0x160 [drm_display_helper] drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper] intel_dp_get_dpcd+0x6f/0x160 [i915] intel_dp_detect+0x306/0x810 [i915] detect_connector_status+0x21/0x60 drm_helper_probe_detect_ctx+0x75/0xe0 drm_helper_probe_detect+0x7b/0x90 intel_hotplug_detect_connector+0x4b/0x140 [i915] ref_tracker: intel_runtime_pm@ffff88813f2c1818 has 1/2 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get+0x1a/0x30 [i915] intel_display_rpm_get+0x1f/0x30 [i915] intel_display_power_get+0x22/0x70 [i915] i915_hpd_poll_init_work+0x1b2/0x2e0 [i915] process_one_work+0x22e/0x6b0 worker_thread+0x1e8/0x3d0 kthread+0x11f/0x250 ret_from_fork+0x344/0x3a0 ret_from_fork_asm+0x1a/0x30 Subtest basic-rte: SUCCESS (1.925s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88813f2c1818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x136b/0x1c50 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x407/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1243/0x26b0 do_syscall_64+0x93/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.925s)
Dmesg	<6> [117.947255] Console: switching to colour dummy device 80x25 <6> [117.947354] [IGT] kms_pm_rpm: executing <6> [117.954506] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [117.954887] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [117.960561] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [117.960572] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [117.960877] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [117.961524] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [117.962068] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [117.962628] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [117.963170] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [117.963420] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [117.964168] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.965597] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.967065] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.968544] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.970089] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.971697] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.973301] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.974851] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.976339] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [117.977222] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [117.977832] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [117.978198] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [117.978727] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [117.979383] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] <7> [117.979390] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [117.983673] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected <7> [117.984218] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [117.984225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [118.049871] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [118.053423] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.053435] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [118.053800] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [118.057000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.057011] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [118.057364] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [118.058078] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [118.058091] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [118.058920] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [118.059330] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [118.060327] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.061945] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.063528] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.065138] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.066928] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.067955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [118.068394] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [118.068872] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [118.069257] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [118.070080] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [118.070551] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [118.070979] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [118.071649] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [118.072442] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [118.073883] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.075762] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.077589] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.079344] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.080377] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [118.081210] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [118.081701] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [118.082600] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [118.082670] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] <7> [118.082684] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [118.087405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected <7> [118.087445] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [118.087455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [118.156461] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [118.160132] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.160142] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [118.160433] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [118.163734] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.163769] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [118.164271] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [118.164355] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [118.164367] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [118.165334] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [118.165937] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [118.167099] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.168820] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.170494] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.172070] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.173944] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.175840] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.177565] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.179309] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.180852] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [118.180912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [118.181290] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [118.181603] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [118.181966] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [118.182785] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [118.183117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [118.183818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [118.184462] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [118.185120] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [118.185658] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [118.186385] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [118.186818] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [118.187434] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [118.187538] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] <7> [118.187546] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [118.191943] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected <7> [118.192031] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [118.192039] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [118.257866] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [118.261298] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.261307] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [118.261549] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [118.264704] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [118.264714] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [118.265156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [118.292138] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [118.292527] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [118.292967] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [118.293453] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [118.294365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [119.267530] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [119.274751] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [119.298983] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [119.308377] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [119.309377] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [119.312044] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A] <7> [119.321861] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [119.346935] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [119.360018] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [119.361981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [119.363278] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [119.364663] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [119.366531] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [119.368115] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [119.370033] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B] <7> [119.371309] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [119.372293] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [119.373973] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.376435] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.378850] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.381180] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.383179] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.385393] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.387346] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.389309] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.391129] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.392246] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [119.393663] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [119.394661] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [119.396561] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C] <7> [119.399163] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [119.403519] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [119.471441] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [119.475215] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [119.475226] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [119.475521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [119.478965] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [119.478978] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [119.499886] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [119.500475] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [119.501059] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [119.501628] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [119.502552] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [119.503239] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [119.509673] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [119.601052] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A] <7> [119.612971] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [119.627392] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [119.628139] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [119.629111] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [119.630580] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [119.632337] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [119.633899] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B] <7> [119.634036] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [119.636632] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [119.637995] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 1 ms <7> [119.640178] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.642623] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.645539] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.647642] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.649801] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.651821] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.653762] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.655760] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.657483] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.658562] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [119.659760] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [119.660747] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [119.662350] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [119.666933] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [119.734846] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [119.738442] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [119.738454] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [119.738779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [119.742310] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [119.742319] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [119.743152] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C] <7> [119.763891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [119.764441] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [119.764955] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [119.765569] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [119.766693] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [119.767199] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [119.773841] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [119.856073] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [119.871506] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [119.872299] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [119.873129] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [119.873926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [119.875268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [119.878383] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [119.880058] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [119.880904] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A] <7> [119.881170] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [119.882394] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [119.884381] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.886798] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.889261] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.891557] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.893933] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.896492] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.898826] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.901227] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.903504] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [119.904937] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [119.907067] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [119.908294] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [119.911003] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <7> [119.915795] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [119.979926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [119.980240] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [119.980509] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [119.980803] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [119.983805] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [119.999845] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [119.999856] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [120.000117] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [120.015513] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [120.015520] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [120.015794] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [120.016097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [120.016328] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [120.016873] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [120.017565] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B] <7> [120.017788] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C] <7> [120.035897] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [120.036213] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [120.036517] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [120.037292] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [120.037577] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [120.041764] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [120.135979] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [120.155529] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [120.156488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [120.157882] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [120.159074] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [120.162017] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [120.162459] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [120.163666] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [120.164841] [IGT] kms_pm_rpm: exiting, ret=0 <7> [120.166454] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [120.167397] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [120.171439] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.174241] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.177106] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.178947] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.180989] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.182956] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.184833] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.186682] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.188344] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [120.189316] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [120.190508] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [120.191284] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [120.192977] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2] <6> [120.193454] Console: switching to colour frame buffer device 128x48 <7> [120.198172] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]

Created at 2025-12-17 00:33:28