Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.2-g1806ab9c9 (x86_64) (Linux: 6.18.0-CI_DRM_17673-g90eba5e4087d+ x86_64)
Out 
Using IGT_SRANDOM=1765568952 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Dmesg
<6> [171.029775] Console: switching to colour dummy device 80x25
<6> [171.029981] [IGT] kms_force_connector_basic: executing
<7> [171.044466] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [171.045764] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [171.062426] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [171.063937] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [171.063946] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.063952] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.068234] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.068259] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.068262] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.072496] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.072527] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.072530] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.076726] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [171.076909] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [171.077211] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [171.077215] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.077218] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.135786] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [171.141401] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.141414] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [171.141720] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [171.147332] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.147339] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [171.147600] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from disconnected to connected
<7> [171.147617] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [171.147688] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [171.147739] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [171.147742] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [171.147745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [171.147749] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [171.147752] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [171.147755] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [171.147784] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.147787] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.206781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [171.212469] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.212476] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [171.212601] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [171.217977] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.217982] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [171.218139] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [171.218142] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [171.218145] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [171.218147] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [171.218149] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [171.218151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [171.218753] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:527:HDMI-A-1] EDID override set
<7> [171.218768] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.218771] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.219347] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD monitor IGT
<7> [171.219351] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD size 24, SAD count 0
<7> [171.279785] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [171.285470] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [171.285612] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [171.285623] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [171.285632] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [171.285636] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [171.285641] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [171.285646] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [171.285650] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [171.285653] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [171.285798] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [171.286009] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.286014] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.347243] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [171.352910] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.352920] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [171.353212] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [171.358699] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [171.358705] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [171.358887] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:527:HDMI-A-1] EDID changed, epoch counter 2
<7> [171.358940] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [171.358945] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [171.358952] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [171.358955] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [171.358957] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [171.358960] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [171.358963] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [171.358966] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [171.359081] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [171.359084] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.359087] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.363329] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from connected to disconnected
<7> [171.363335] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.363341] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [171.363377] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [171.363416] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.363420] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.367697] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [171.367937] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [171.368304] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [171.369392] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:506:eDP-1] force updated from 0 to 0 or reprobing
<7> [171.369396] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [171.369399] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [171.370031] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [171.370507] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [171.370643] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.370776] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.370927] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [171.370930] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [171.370933] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [171.370935] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [171.370951] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [171.371081] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [171.371220] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [171.372020] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [171.372023] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [171.372045] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [171.372048] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [171.372680] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [171.373133] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [171.373277] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.373407] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.373551] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [171.373554] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [171.373556] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [171.373558] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [171.373566] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [171.373699] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [171.373830] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [171.374603] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [171.374605] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [171.374676] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:506:eDP-1] EDID override reset
<7> [171.374686] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [171.374689] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [171.375300] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [171.375722] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [171.375855] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.375987] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.376132] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [171.376135] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [171.376137] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [171.376139] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [171.376146] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [171.376289] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [171.376416] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [171.377147] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [171.377150] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [171.377229] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:515:DP-1] EDID override reset
<7> [171.377240] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [171.377243] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [171.381426] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [171.381526] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [171.381529] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.381532] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.385759] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.385778] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.385781] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.390021] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.390084] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [171.390094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.390097] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.394292] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.394360] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:533:DP-2] EDID override reset
<7> [171.394370] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [171.394373] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [171.394638] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [171.394697] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:542:DP-3] EDID override reset
<7> [171.394708] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [171.394711] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [171.394950] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [171.395007] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:551:DP-4] EDID override reset
<7> [171.395017] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [171.395019] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [171.395283] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [171.395341] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:560:DP-5] EDID override reset
<7> [171.395351] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [171.395353] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [171.395589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<6> [171.395974] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [171.396474] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [171.414065] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [171.414072] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [171.414122] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [171.414127] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [171.414780] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [171.415237] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [171.415375] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.415509] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [171.415655] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [171.415658] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [171.415660] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [171.415663] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [171.415673] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [171.415805] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [171.415940] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [171.417145] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [171.417150] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [171.417153] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [171.417157] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [171.421416] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [171.421420] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [171.421423] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [171.425655] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [171.425658] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [171.425661] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [171.425924] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [171.425927] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [171.425929] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [171.426171] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [171.426173] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [171.426176] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [171.426431] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [171.426434] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [171.426436] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [171.426679] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<7> [171.426681] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] enabled? yes
<7> [171.426684] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:515:DP-1] enabled? no
<7> [171.426687] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:527:HDMI-A-1] enabled? no
<7> [171.426689] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:533:DP-2] enabled? no
<7> [171.426691] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:542:DP-3] enabled? no
<7> [171.426693] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:551:DP-4] enabled? no
<7> [171.426694] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:560:DP-5] enabled? no
<7> [171.426715] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [171.426725] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] found preferred mode: 3840x2400
<7> [171.426727] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [171.426738] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:149:pipe A] desired mode 3840x2400 set (0,0)
<7> [171.430694] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [171.447452] Console: switching to colour frame buffer device 240x75
Created at 2025-12-13 04:11:38