Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 11.53 seconds
Igt-Version 
IGT-Version: 2.2-g46d3dad03 (x86_64) (Linux: 6.18.0-rc7-CI_DRM_17596-g943d0e69375e+ x86_64)
Out 
Using IGT_SRANDOM=1764256892 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88814776d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x5ee/0x810 [i915]
     intel_dp_aux_transfer+0xd4/0x340 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x2d8/0x7b0 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.529s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88814776d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b5e/0x26a0
     do_syscall_64+0x93/0xd60
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.529s)
Dmesg
<6> [117.637891] Console: switching to colour dummy device 80x25
<6> [117.637960] [IGT] kms_pm_rpm: executing
<6> [117.645714] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [117.646165] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [117.649833] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [117.649842] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [117.649874] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.650114] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.650331] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.650544] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.651254] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.651493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.656440] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [117.656917] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [117.656923] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [117.657527] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [117.658055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [117.658619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [117.659583] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [117.660381] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [117.661141] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [117.661478] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [117.661484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [117.662016] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.662199] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [117.662595] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.662901] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.662906] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.663099] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.667362] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.667368] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.667562] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [117.667865] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [117.667870] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [117.672109] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [117.672127] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [117.672131] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [117.673126] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [117.673776] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [117.674681] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [117.674699] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [117.674703] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [117.675172] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.675362] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [117.675777] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.676061] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.676066] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.676246] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.680441] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.680446] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.680650] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [117.680674] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [117.680678] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [117.685009] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [117.685053] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [117.685057] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [117.686088] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [117.686798] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [117.687687] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [117.687732] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [117.687748] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [117.688189] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.688372] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [117.688853] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [117.689115] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.689119] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.689300] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.693525] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.693530] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.693722] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [117.762963] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.763547] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.764109] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.764613] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.765582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [128.746448] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [128.756719] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [128.781387] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [128.786847] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [128.787493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [128.787844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [128.788099] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [128.792472] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [128.793293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [128.793939] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [128.794629] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [128.796329] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [128.797637] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [128.799620] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [128.799615] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [128.800087] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.800316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [128.800720] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.800958] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.800963] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.801142] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [128.805540] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.805545] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [128.805894] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [128.905436] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [128.905872] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [128.906220] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [128.906600] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [128.907432] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [128.907805] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [128.912340] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [129.007573] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [129.019972] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [129.028484] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [129.028944] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [129.029545] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [129.030445] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [129.032006] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [129.032703] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [129.037058] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [129.037582] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [129.039224] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [129.040639] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [129.042887] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [129.042821] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [129.043453] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.043806] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.044378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.044775] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.044783] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.045105] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.049548] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.049553] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.050406] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [129.050643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [129.050844] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [129.051040] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [129.051719] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [129.051968] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [129.055165] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [129.162416] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [129.170935] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [129.171470] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [129.172055] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [129.172827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [129.173572] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [129.174893] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [129.175357] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [129.176804] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [129.177626] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [129.179560] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [129.180937] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [129.183176] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [129.183133] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [129.183637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.183845] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.184249] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.184503] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.184508] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.184703] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.188887] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.188893] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.189223] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [129.281553] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [129.282251] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [129.282959] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [129.283640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [129.284767] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [129.285426] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [129.294343] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [129.407462] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [129.417603] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [129.417867] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [129.418136] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [129.418767] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [129.419772] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [129.419910] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<6> [129.420336] [IGT] kms_pm_rpm: exiting, ret=0
<7> [129.424309] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [129.424640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [129.426072] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [129.427296] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [129.429345] Console: switching to colour frame buffer device 128x48
<7> [129.432448] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [129.432920] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.433118] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.433562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.433881] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.433888] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.434159] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.438358] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [129.438614] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [129.438844] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [129.439041] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [129.439732] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.439753] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.440040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2025-11-27 17:50:42