Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.2-g5aeea13f5 (x86_64) (Linux: 6.18.0-rc6-CI_DRM_17572-ga95032b2166b+ x86_64)
Out 
Using IGT_SRANDOM=1763603537 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Dmesg
<6> [175.358626] Console: switching to colour dummy device 80x25
<6> [175.358829] [IGT] kms_force_connector_basic: executing
<7> [175.371625] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [175.374209] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [175.380628] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [175.382301] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:283:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [175.382314] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.382322] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.386752] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.386775] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.386778] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.390979] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.391012] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.391014] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.395231] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<6> [175.395426] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [175.395748] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:283:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [175.395754] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.395757] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.454982] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [175.460895] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.460919] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [175.461306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [175.467109] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.467136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [175.467496] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] status updated from disconnected to connected
<7> [175.467521] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [175.467612] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [175.467689] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] probed modes:
<7> [175.467695] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [175.467700] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [175.467705] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [175.467710] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [175.467714] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [175.467773] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.467778] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.528966] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [175.534871] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.534879] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [175.535019] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [175.540403] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.540407] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [175.540573] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] probed modes:
<7> [175.540577] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [175.540580] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [175.540582] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [175.540584] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [175.540586] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [175.540870] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:283:HDMI-A-1] EDID override set
<7> [175.540884] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.540886] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.541137] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:283:HDMI-A-1] ELD monitor IGT
<7> [175.541141] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:283:HDMI-A-1] ELD size 24, SAD count 0
<7> [175.599418] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [175.605078] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [175.605242] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [175.605254] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [175.605264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] probed modes:
<7> [175.605268] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [175.605274] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [175.605279] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [175.605283] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [175.605288] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [175.605420] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:283:HDMI-A-1] EDID override reset
<7> [175.605586] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.605589] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.666411] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [175.672073] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.672080] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [175.672227] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [175.677620] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [175.677624] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [175.677745] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:283:HDMI-A-1] EDID changed, epoch counter 2
<7> [175.677784] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [175.677789] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [175.677794] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] probed modes:
<7> [175.677796] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [175.677798] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [175.677800] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [175.677802] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [175.677805] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [175.677919] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:283:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [175.677922] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.677925] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.682143] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] status updated from connected to disconnected
<7> [175.682150] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.682183] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.682185] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.682378] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [175.682425] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [175.686436] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<6> [175.686824] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [175.687472] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [175.689021] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:262:eDP-1] force updated from 0 to 0 or reprobing
<7> [175.689026] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1]
<7> [175.689029] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:262:eDP-1]
<7> [175.689676] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [175.690118] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [175.690262] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.690409] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.690557] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [175.690562] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [175.690565] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD monitor
<7> [175.690567] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD size 20, SAD count 0
<7> [175.690578] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] VRR capable: yes
<7> [175.690710] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [175.690840] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [175.691619] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1] probed modes:
<7> [175.691622] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [175.691644] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1]
<7> [175.691647] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:262:eDP-1]
<7> [175.692280] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [175.692716] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [175.692847] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.692977] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.693118] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [175.693121] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [175.693124] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD monitor
<7> [175.693127] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD size 20, SAD count 0
<7> [175.693136] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] VRR capable: yes
<7> [175.693264] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [175.693406] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [175.694155] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1] probed modes:
<7> [175.694157] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [175.694230] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:262:eDP-1] EDID override reset
<7> [175.694241] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1]
<7> [175.694244] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:262:eDP-1]
<7> [175.694874] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [175.695282] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [175.695423] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.695554] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.695693] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [175.695697] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [175.695699] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD monitor
<7> [175.695702] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD size 20, SAD count 0
<7> [175.695710] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] VRR capable: yes
<7> [175.695838] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [175.695969] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [175.696728] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1] probed modes:
<7> [175.696731] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [175.696810] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:271:DP-1] EDID override reset
<7> [175.696821] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-1]
<7> [175.696823] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-1]
<7> [175.701036] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-1] disconnected
<7> [175.701138] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:283:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [175.701141] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.701144] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.705388] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.705409] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.705412] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.709638] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.709700] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:283:HDMI-A-1] EDID override reset
<7> [175.709709] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.709712] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.713930] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.713995] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:289:DP-2] EDID override reset
<7> [175.714004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:289:DP-2]
<7> [175.714007] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:289:DP-2]
<7> [175.714270] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:289:DP-2] disconnected
<7> [175.714329] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:298:DP-3] EDID override reset
<7> [175.714339] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:298:DP-3]
<7> [175.714341] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:298:DP-3]
<7> [175.714589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:298:DP-3] disconnected
<7> [175.714648] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:307:DP-4] EDID override reset
<7> [175.714657] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:307:DP-4]
<7> [175.714660] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:307:DP-4]
<7> [175.714894] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:307:DP-4] disconnected
<7> [175.714950] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:316:DP-5] EDID override reset
<7> [175.714959] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:316:DP-5]
<7> [175.714961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:316:DP-5]
<7> [175.715195] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:316:DP-5] disconnected
<6> [175.715575] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [175.715990] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [175.752020] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [175.752028] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [175.752095] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1]
<7> [175.752101] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:262:eDP-1]
<7> [175.753285] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [175.754278] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [175.754778] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.755258] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [175.755872] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [175.755888] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [175.755899] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD monitor
<7> [175.755910] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:262:eDP-1] ELD size 20, SAD count 0
<7> [175.755943] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] VRR capable: yes
<7> [175.756234] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [175.756523] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:262:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [175.757551] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:262:eDP-1] probed modes:
<7> [175.757556] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [175.757560] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-1]
<7> [175.757563] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-1]
<7> [175.761808] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-1] disconnected
<7> [175.761812] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1]
<7> [175.761815] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:283:HDMI-A-1]
<7> [175.766003] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:283:HDMI-A-1] disconnected
<7> [175.766006] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:289:DP-2]
<7> [175.766009] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:289:DP-2]
<7> [175.766282] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:289:DP-2] disconnected
<7> [175.766285] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:298:DP-3]
<7> [175.766287] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:298:DP-3]
<7> [175.766542] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:298:DP-3] disconnected
<7> [175.766545] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:307:DP-4]
<7> [175.766547] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:307:DP-4]
<7> [175.766791] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:307:DP-4] disconnected
<7> [175.766793] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:316:DP-5]
<7> [175.766796] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:316:DP-5]
<7> [175.767035] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:316:DP-5] disconnected
<7> [175.767037] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:262:eDP-1] enabled? yes
<7> [175.767040] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:271:DP-1] enabled? no
<7> [175.767042] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:283:HDMI-A-1] enabled? no
<7> [175.767044] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:289:DP-2] enabled? no
<7> [175.767045] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:298:DP-3] enabled? no
<7> [175.767047] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:307:DP-4] enabled? no
<7> [175.767049] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:316:DP-5] enabled? no
<7> [175.767071] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [175.767083] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:262:eDP-1] found preferred mode: 3840x2400
<7> [175.767085] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [175.767104] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 3840x2400 set (0,0)
<7> [175.768613] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [175.785353] Console: switching to colour frame buffer device 240x75
Created at 2025-11-20 12:44:23