Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.4-g866791425 (x86_64) (Linux: 7.1.0-rc6-CI_DRM_18636-ga7cae78fc6c6+ x86_64)
Out	Using IGT_SRANDOM=1780677237 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888130461840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x1bba/0x20c0 [i915] intel_atomic_commit+0x2ff/0x350 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0x103/0x6d0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.421s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888130461840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x300 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0x103/0x6d0
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.421s)
Dmesg	<6> [64.974945] Console: switching to colour dummy device 80x25 <6> [64.975001] [IGT] kms_pm_rpm: executing <6> [64.977027] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [64.977255] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [64.982502] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [64.982509] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [64.986710] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [64.986954] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [64.986957] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [64.991243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [64.991502] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [64.991506] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [64.995768] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [64.996002] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [64.996006] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [65.000264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [65.000276] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [65.000279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [65.004498] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [65.004509] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [65.004512] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [65.008147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [65.008325] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [65.008489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [65.009852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [65.009875] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [65.009880] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [65.014720] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [65.014754] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [65.014757] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [65.019588] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [65.019622] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [65.019626] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [65.024468] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [65.128345] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.026422] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.033639] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.035011] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.035458] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.035746] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.035885] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.038266] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.063272] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.070259] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.070408] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.070580] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.070808] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.071011] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.071240] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.071436] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.071617] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.071869] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.072006] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.072503] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.073491] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.074043] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.083070] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.084394] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [66.084255] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.084604] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.085476] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.086947] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [66.086892] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.091218] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.095473] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.099824] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [66.117300] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.117458] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.117596] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.118865] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.119320] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.125039] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.126353] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.126588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.126875] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.127014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.129207] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.200910] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [66.213327] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.222133] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.222973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.223917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.224879] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.225836] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.226779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.227705] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.228616] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.229563] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.229967] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.230365] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.231058] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.231208] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.237350] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.237541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.237769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.238750] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.240226] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.240405] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [66.244808] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.249166] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [66.249162] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.271375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.271741] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.272064] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.273575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.273944] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.279792] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.281497] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.282486] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.283488] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.284138] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.290140] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.366323] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.374140] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.374989] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.375908] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.376866] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.377807] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.378730] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.379636] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.380518] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.381448] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.382263] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.384096] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.386576] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.387401] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.396734] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.396935] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.397426] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [66.399758] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [66.399966] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [66.402264] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.407140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.412100] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.413129] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.414584] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [66.414694] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [66.504311] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.504853] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.505759] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.507871] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.508822] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.516127] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.517870] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.518891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.519997] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.520691] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.527138] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.633568] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.641129] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.641972] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.642930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.644001] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.644994] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.645978] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.646929] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.647855] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.649448] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.650242] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.651201] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.653661] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.654318] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.667041] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.667424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.667571] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.668320] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.669882] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [66.669983] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [66.670232] [IGT] kms_pm_rpm: exiting, ret=0 <7> [66.674186] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <6> [66.678747] Console: switching to colour frame buffer device 160x45 <7> [66.679364] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2]

Created at 2026-06-06 07:40:18