Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.4-g53cdcbd04 (x86_64) (Linux: 7.1.0-rc6-CI_DRM_18634-gfe3f27ecb39e+ x86_64)
Out	Using IGT_SRANDOM=1780661351 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888142325840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x1bba/0x20c0 [i915] intel_atomic_commit+0x2ff/0x350 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0x103/0x6d0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.420s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888142325840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x300 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0x103/0x6d0
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.420s)
Dmesg	<6> [66.962319] Console: switching to colour dummy device 80x25 <6> [66.962439] [IGT] kms_pm_rpm: executing <6> [66.964474] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [66.964677] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [66.969659] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [66.969666] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.973874] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [66.974120] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [66.974123] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.978330] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [66.978571] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [66.978575] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.982741] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [66.982966] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [66.982969] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.987172] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [66.987184] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [66.987187] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.991371] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [66.991383] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [66.991386] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.995599] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [66.995617] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [66.995620] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.996227] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.996417] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.996579] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.000371] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [67.000405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [67.000408] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [67.005244] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [67.005278] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [67.005281] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [67.010123] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [67.115226] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.009779] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [68.015940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.017304] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.017729] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.018027] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.018169] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.019883] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [68.045018] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [68.051791] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.051954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.052126] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.052353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.052555] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.053431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.054349] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.055225] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.056890] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.057666] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.059344] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.060263] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.060401] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.067757] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [68.068984] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.069146] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.070306] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [68.073945] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.078879] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.083701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.083842] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.083989] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.084817] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.086223] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [68.086308] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [68.103880] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.104245] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.104572] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.106098] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.106724] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [68.113885] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.115613] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.117155] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.118052] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.118529] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.122713] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [68.187173] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [68.199714] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [68.208375] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.209278] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.210196] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.211144] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.212096] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.213024] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.213941] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.214694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.214950] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.215086] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.215559] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.216242] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.216383] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.222543] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [68.222656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.222796] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.223773] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.225593] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.225768] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [68.229808] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.234105] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.234271] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [68.256626] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.257012] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.257508] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.259375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.260200] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [68.267659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.269367] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.270147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.271038] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.271697] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.275301] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [68.351401] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [68.360049] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.360942] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.361849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.362796] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.363741] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.364656] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.365574] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.366451] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.368066] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.368909] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.370487] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.372928] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.373771] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.383093] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [68.383309] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.384563] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [68.385172] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [68.385421] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [68.389480] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.394377] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.399310] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.400350] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.401794] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [68.401902] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [68.488248] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.489203] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.490049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.492386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.494625] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [68.500898] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.502233] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.502484] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.502771] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.502924] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.504855] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [68.620115] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [68.628655] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.629488] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.630450] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.631443] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.632504] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.633316] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.634103] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.634849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.635978] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.636427] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.637601] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.639069] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.639387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.648158] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [68.648329] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.648471] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.649371] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.650988] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [68.651094] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [68.651338] [IGT] kms_pm_rpm: exiting, ret=0 <7> [68.655310] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <6> [68.659920] Console: switching to colour frame buffer device 160x45 <7> [68.660667] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2]

Created at 2026-06-06 01:20:47