Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.43 seconds
Igt-Version	IGT-Version: 2.4-g53cdcbd04 (x86_64) (Linux: 7.1.0-rc6-CI_DRM_18633-g6be5b7e4d84e+ x86_64)
Out	Using IGT_SRANDOM=1780658886 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88811c035840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x1bba/0x20c0 [i915] intel_atomic_commit+0x2ff/0x350 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0x103/0x6d0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.432s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88811c035840 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x300 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0x103/0x6d0
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.432s)
Dmesg	<6> [65.689897] Console: switching to colour dummy device 80x25 <6> [65.689948] [IGT] kms_pm_rpm: executing <6> [65.692587] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [65.692803] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [65.697962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [65.697969] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [65.702226] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [65.702465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [65.702470] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [65.706667] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [65.706912] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [65.706915] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [65.711131] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [65.711358] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [65.711361] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [65.715576] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [65.715589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [65.715592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [65.719798] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [65.719810] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [65.719813] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [65.724025] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [65.724051] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [65.724055] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [65.728076] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [65.728269] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [65.728410] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [65.729706] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [65.729766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [65.729771] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [65.734643] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [65.734677] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [65.734680] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [65.739529] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [65.840209] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.741523] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.747724] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.749062] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.749428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.749739] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.749879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.751675] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.776880] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.784819] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.785542] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.786495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.787602] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.789718] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.790811] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.791799] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.792858] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.794432] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.795189] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.796715] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.798695] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.799222] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.808177] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.809402] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.809533] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [66.809668] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.810600] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.812019] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [66.812017] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.816275] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.820531] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.824887] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [66.842708] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.843119] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.843498] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.845060] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.845748] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [66.850341] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.851714] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.851997] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.852292] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.852434] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.854663] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [66.925900] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [66.938487] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [66.947721] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.948568] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.949521] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.950497] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.951473] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.952440] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.953419] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.953654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.953898] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.954033] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.954452] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.955167] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.955344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.962706] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [66.962818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.962956] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.963920] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.965517] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [66.965596] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [66.969789] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [66.974023] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [66.978377] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [66.995780] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.995938] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.996077] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.997368] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.997842] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [67.002402] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.003810] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [67.004465] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [67.005207] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [67.005749] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [67.011556] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [67.091458] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [67.100659] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [67.101509] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [67.102436] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [67.103442] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.104396] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.105330] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.106260] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.107146] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [67.108094] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [67.108921] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [67.110562] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [67.112769] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.113272] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.122241] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [67.122402] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.122839] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [67.125486] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [67.127985] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [67.127940] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [67.132807] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [67.137761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [67.138791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.140226] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [67.140333] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [67.231795] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [67.232709] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.233559] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.235569] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.236707] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Suspending device <7> [67.245203] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.247010] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [67.247859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [67.248679] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [67.249264] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [67.253546] i915 0000:00:02.0: [drm:i915_pm_runtime_suspend [i915]] Device suspended <7> [67.359011] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Resuming device <7> [67.367586] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [67.368433] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [67.369383] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [67.370357] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.371348] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.372299] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.373262] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.374175] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [67.375763] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [67.376559] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [67.377520] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [67.379982] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.380661] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.392153] i915 0000:00:02.0: [drm:i915_pm_runtime_resume [i915]] Device resumed <7> [67.392338] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.392529] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [67.393372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.394966] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [67.395069] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [67.395311] [IGT] kms_pm_rpm: exiting, ret=0 <7> [67.399286] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <6> [67.403866] Console: switching to colour frame buffer device 160x45 <7> [67.404601] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2]

Created at 2026-06-06 00:09:28