Results for igt@i915_module_load@load

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 1.72 seconds
Igt-Version
IGT-Version: 2.4-gaa5853ef5 (x86_64) (Linux: 7.1.0-rc1-CI_DRM_18399-gcc244a15b801+ x86_64)
Out
Using IGT_SRANDOM=1777880100 for randomisation
Starting subtest: load
Opened device: /dev/dri/card0
Subtest load: SUCCESS (1.721s)
Err
Starting subtest: load
Subtest load: SUCCESS (1.721s)
Dmesg
<6> [43.624614] [IGT] i915_module_load: executing
<4> [43.624702] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030
<6> [43.725629] [IGT] i915_module_load: starting subtest load
<4> [44.902243]
<4> [44.902252] **********************************************************
<4> [44.902254] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [44.902255] ** **
<4> [44.902256] ** trace_printk() being used. Allocating extra memory. **
<4> [44.902258] ** **
<4> [44.902259] ** This means that this is a DEBUG kernel and it is **
<4> [44.902260] ** unsafe for production use. **
<4> [44.902262] ** **
<4> [44.902263] ** If you see this message and you are not debugging **
<4> [44.902264] ** the kernel, report this immediately to your vendor! **
<4> [44.902266] ** **
<4> [44.902267] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [44.902268] **********************************************************
<5> [44.932252] Setting dangerous option force_probe - tainting kernel
<6> [44.945939] i915 0000:00:02.0: [drm] Found ivybridge (device ID 0162) integrated display version 7.00 stepping N/A
<7> [44.948347] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [44.948614] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found CougarPoint PCH
<7> [44.948863] i915 0000:00:02.0: [drm:intel_dmc_wl_init [i915]] Sanitized enable_dmc_wl value: 0 (disabled)
<7> [44.949149] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [44.950017] i915 0000:00:02.0: [drm:intel_display_device_info_runtime_init [i915]] rawclk rate: 125000 kHz
<7> [44.951009] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 2048M
<7> [44.951250] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [44.951534] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [44.951786] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [44.952844] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [44.953862] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<5> [44.953875] i915 0000:00:02.0: [drm] DMAR active, disabling use of stolen memory
<7> [44.953878] i915 0000:00:02.0: [drm:init_stolen_smem [i915]] Skip stolen region: failed to setup
<7> [44.954120] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(0): system: 3727 MiB [mem 0x00000000-0xe8fa4fff], io: n/a
<7> [44.954509] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(5): stolen-system: 64 MiB [mem 0xdb200000-0xdf1fffff], io: n/a
<7> [44.955170] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xd8f5e018
<7> [44.955561] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [44.955818] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [44.956055] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [44.962608] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cf3, SBCB callbacks 00000241
<7> [44.962858] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [44.963132] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM type: UNKNOWN
<7> [44.963401] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 0
<7> [44.963758] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num QGV points 0
<7> [44.964057] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num PSF GV points 0
<7> [44.964989] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [44.965267] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SNB/IVB-DESKTOP", BDB version 166
<7> [44.965539] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [44.965955] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 269, min size 5)
<7> [44.966226] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [44.966482] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [44.966856] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 22 (size 75, min size 22)
<7> [44.967240] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 23 (size 72, min size 72)
<7> [44.967510] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 204, min size 850)
<7> [44.967798] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34)
<7> [44.968050] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [44.968303] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1264, min size 1366)
<7> [44.968552] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 113, min size 305)
<7> [44.968838] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 136)
<7> [44.969082] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 1 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [44.969326] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [44.969569] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68d2
<7> [44.970052] i915 0000:00:02.0: [drm:intel_bios_init [i915]] No SDVO device info is found in VBT
<7> [44.970306] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:0 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [44.970550] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4
<7> [44.970871] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 00
<7> [44.971252] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.972576] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 0
<7> [44.972994] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 12 (1.2 usec)
<7> [44.973273] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 4 (2.0 usec)
<7> [44.973512] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 16 (8.0 usec)
<7> [44.973750] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency 32 (16.0 usec)
<7> [44.974040] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 12 (1.2 usec)
<7> [44.974297] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 4 (2.0 usec)
<7> [44.974535] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 16 (8.0 usec)
<7> [44.974772] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency 32 (16.0 usec)
<7> [44.975046] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 12 (1.2 usec)
<7> [44.975302] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 4 (2.0 usec)
<7> [44.975539] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 16 (8.0 usec)
<7> [44.975776] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency 32 (16.0 usec)
<7> [44.982385] i915 0000:00:02.0: [drm:intel_crtc_init [i915]] 3 display pipes available.
<7> [44.983991] i915 0000:00:02.0: [drm:intel_fdi_pll_freq_update [i915]] FDI PLL freq=270000
<7> [44.984289] i915 0000:00:02.0: [drm:intel_cdclk_read_hw [i915]] Current CDCLK 400000 kHz, VCO 0 kHz, ref 0 kHz, bypass 0 kHz, voltage level 0
<7> [44.984546] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 400000 kHz
<7> [44.984850] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max dotclock rate: 360000 kHz
<7> [44.985892] i915 0000:00:02.0: [drm:intel_crt_reset [i915]] crt adpa set to 0x80f40018
<7> [44.986335] i915 0000:00:02.0: [drm:intel_sdvo_init [i915]] [ENCODER:94:SDVO B] I2C pin 5, target addr 0x38
<7> [44.986744] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [44.988795] i915 0000:00:02.0: [drm:intel_sdvo_read_byte [i915]] i2c transfer returned -6
<7> [44.989176] i915 0000:00:02.0: [drm:intel_sdvo_init [i915]] No SDVO device found on SDVOB
<7> [44.989609] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [44.990041] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:HDMI B]
<7> [44.990336] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:HDMI B] Using DDC pin 0x5 (VBT)
<7> [44.991265] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DP B] Using AUX CH B (platform default)
<7> [44.991569] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DP B]
<7> [44.992053] i915 0000:00:02.0: [drm:intel_init_pch_refclk [i915]] has_panel 0 has_lvds 0 has_ck505 0 using_ssc_source 0
<7> [44.992605] i915 0000:00:02.0: [drm:intel_vga_disable [i915]] VGA plane is disabled
<6> [44.992867] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io:owns=io+mem
<7> [44.993402] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:53:pipe A] hw state readout: enabled
<7> [44.993693] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [44.993947] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:91:pipe C] hw state readout: disabled
<7> [44.994201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:primary A] hw state readout: enabled, pipe A
<7> [44.994816] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:sprite A] hw state readout: disabled, pipe A
<7> [44.995071] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [44.995323] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:primary B] hw state readout: disabled, pipe B
<7> [44.995738] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:59:sprite B] hw state readout: disabled, pipe B
<7> [44.995992] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:66:cursor B] hw state readout: disabled, pipe B
<7> [44.996243] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:primary C] hw state readout: disabled, pipe C
<7> [44.996518] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:sprite C] hw state readout: disabled, pipe C
<7> [44.996792] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:cursor C] hw state readout: disabled, pipe C
<7> [44.997051] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:93:CRT] hw state readout: enabled, pipe A
<7> [44.997306] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:HDMI B] hw state readout: disabled, pipe A
<7> [44.997653] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [44.997914] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DP B] hw state readout: disabled, pipe A
<7> [44.998165] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:53:pipe A] reserving PCH DPLL A
<7> [44.998411] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL A hw state readout: pipe_mask 0x1, on 1
<7> [44.998716] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL B hw state readout: pipe_mask 0x0, on 0
<7> [44.999043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:92:VGA-1] hw state readout: enabled
<7> [44.999314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled
<7> [44.999621] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [44.999904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [45.000278] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:primary A] min_cdclk 108000 kHz
<7> [45.000560] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:sprite A] min_cdclk 0 kHz
<7> [45.000853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [45.001140] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:53:pipe A] min_cdclk 120000 kHz
<7> [45.001382] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:primary B] min_cdclk 0 kHz
<7> [45.001662] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:59:sprite B] min_cdclk 0 kHz
<7> [45.001921] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:66:cursor B] min_cdclk 0 kHz
<7> [45.002193] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] min_cdclk 0 kHz
<7> [45.002434] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:primary C] min_cdclk 0 kHz
<7> [45.002731] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:sprite C] min_cdclk 0 kHz
<7> [45.003011] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:cursor C] min_cdclk 0 kHz
<7> [45.003251] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:91:pipe C] min_cdclk 0 kHz
<7> [45.003814] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: yes [setup_hw_state]
<7> [45.004060] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: ANALOG (0x2), output format: RGB, sink format: RGB
<7> [45.004316] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [45.004562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [45.004849] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [45.005115] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [45.005360] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [45.005621] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fdi: lanes: 2; data_m: 5033164, data_n: 8388608, link_m: 209715, link_n: 524288, tu: 64
<7> [45.005913] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [45.006178] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [45.006423] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [45.006668] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0
<7> [45.006949] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0
<7> [45.007233] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [45.007479] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [45.007735] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [45.008013] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=108000, hd=1280 hb=1280-1688 hs=1328-1440 ht=1688, vd=1024 vb=1024-1066 vs=1025-1028 vt=1066, flags=0x5
<7> [45.008279] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [45.008525] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=108000, hd=1280 hb=1280-1688 hs=1328-1440 ht=1688, vd=1024 vb=1024-1066 vs=1025-1028 vt=1066, flags=0x5
<7> [45.008809] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 108000, pixel rate 108000, min cdclk 120000, min voltage level 0
<7> [45.009074] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [45.009318] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 1280x1024+0+0
<7> [45.009564] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 1280x1024+0+0, enabled, force thru: no
<7> [45.009854] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [45.010129] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [45.010374] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: dpll: 0xc4040004, dpll_md: 0x0, fp0: 0x10c09, fp1: 0x30d07
<7> [45.010619] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [45.010924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [45.011189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [45.011435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.011680] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.011961] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.012225] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [45.012471] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [45.012716] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:91:pipe C] enable: no [setup_hw_state]
<7> [45.013059] i915 0000:00:02.0: [drm:i9xx_get_initial_plane_config [i915]] [CRTC:53:pipe A][PLANE:35:primary A] with fb: size=1280x1024@32, offset=0, pitch 5120, size 0x500000
<7> [45.013324] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Using dma_addr=0x00000000db200000, based on initial plane programming
<7> [45.013560] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Initial FB size exceeds half of stolen, discarding
<7> [45.013813] i915 0000:00:02.0: [drm:intel_plane_disable_noatomic [i915]] Disabling [PLANE:35:primary A] on [CRTC:53:pipe A]
<7> [45.021684] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [45.021928] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 80000000]
<7> [45.043896] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 4 GT workarounds on global
<7> [45.045054] i915 0000:00:02.0: [drm:intel_rps_init [i915]] Overclocking supported, max: 1150MHz, overclock: 1150MHz
<7> [45.045647] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 engine workarounds on rcs'0
<7> [45.045973] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 3 context workarounds on rcs'0
<7> [45.061093] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0
<7> [45.061371] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0
<7> [45.061626] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0
<7> [45.061894] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:53:pipe A] FQ 0: start 0x8
<7> [45.062221] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:53:pipe A] FQ 1: start 0x108
<7> [45.062490] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:53:pipe A] FQ 2: start 0x208
<7> [45.062748] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:53:pipe A] FQ 3: start 0x308
<7> [45.063005] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:53:pipe A] FQ 4: start 0x3c8
<7> [45.063288] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:72:pipe B] FQ 0: start 0x8
<7> [45.063542] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:72:pipe B] FQ 1: start 0x108
<7> [45.063785] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:72:pipe B] FQ 2: start 0x208
<7> [45.064027] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:72:pipe B] FQ 3: start 0x308
<7> [45.064304] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:72:pipe B] FQ 4: start 0x3c8
<7> [45.064587] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:91:pipe C] FQ 0: start 0x8
<7> [45.064830] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:91:pipe C] FQ 1: start 0x108
<7> [45.065072] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:91:pipe C] FQ 2: start 0x208
<7> [45.065357] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:91:pipe C] FQ 3: start 0x308
<7> [45.065629] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:91:pipe C] FQ 4: start 0x3c8
<7> [45.066020] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [fastset]
<7> [45.066303] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:91:pipe C] enable: no [fastset]
<7> [45.071319] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:72:pipe B]
<7> [45.071979] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:91:pipe C]
<7> [45.078346] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:92:VGA-1] adding connector to sysfs
<7> [45.080829] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:92:VGA-1] generating connector hotplug event
<7> [45.081002] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:95:HDMI-A-1] adding connector to sysfs
<7> [45.082579] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event
<7> [45.082877] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:103:DP-1] adding connector to sysfs
<7> [45.084216] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DP B bus for card0-DP-1
<7> [45.087979] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<6> [45.098156] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0
<6> [45.111342] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [45.116346] input: Video Bus as /devices/pci0000:00/acpi.video_bus.0/input/input2
<6> [45.121026] snd_hda_intel 0000:00:1b.0: codec_mask forced to 0x4
<7> [45.120878] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:92:VGA-1] force=0
<7> [45.121257] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] trigger hotplug detect cycle: adpa=0x83f40018
<7> [45.121552] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [PLANE:35:primary A] no fb, skipping
<7> [45.121943] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:72:pipe B] not active, skipping
<7> [45.122317] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:91:pipe C] not active, skipping
<7> [45.122685] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] no active fbs found, not using BIOS config
<7> [45.123505] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [45.124443] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [45.130958] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40018, result 1
<7> [45.131246] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [45.131501] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:92:VGA-1] status updated from unknown to connected (epoch counter 0->1)
<7> [45.131783] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [45.132595] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.133079] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [45.135186] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.135503] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.135509] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.135747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [45.137137] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.137143] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [45.137424] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected (epoch counter 0->1)
<7> [45.137672] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [45.142091] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:103:DP-1] status updated from unknown to disconnected (epoch counter 0->1)
<7> [45.142402] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<6> [45.142720] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [i915])
<7> [45.143099] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:92:VGA-1]
<7> [45.143117] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:92:VGA-1] force=1
<7> [45.144077] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40018, result 1
<7> [45.144347] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [45.144960] azx_first_init: snd_hda_intel 0000:00:1b.0: chipset global capabilities = 0x4401
<7> [45.144921] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [45.145254] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [45.145939] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [45.146185] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [45.146190] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.146944] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [45.147444] azx_init_pci: snd_hda_intel 0000:00:1b.0: Clearing TCSEL
<7> [45.147463] azx_init_pci: snd_hda_intel 0000:00:1b.0: SCH snoop: Enabled
<7> [45.148628] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [45.148635] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [45.149457] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:92:VGA-1] probed modes:
<7> [45.149467] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [45.149472] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [45.149477] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [45.149482] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [45.149486] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [45.149492] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [45.149497] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [45.149968] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.150341] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [45.150918] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.151293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.151300] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.151691] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [45.153397] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.153407] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [45.153816] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [45.153828] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [45.153837] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [45.158365] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [45.158376] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:92:VGA-1] enabled? yes
<7> [45.158382] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:95:HDMI-A-1] enabled? no
<7> [45.158386] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:103:DP-1] enabled? no
<7> [45.158507] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [45.158542] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:92:VGA-1] found first mode: 1024x768
<7> [45.158546] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [45.158563] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:53:pipe A] desired mode 1024x768 set (0,0)
<7> [45.158770] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [45.158799] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] no BIOS fb, allocating a new one
<6> [45.159079] i915 0000:00:02.0: [drm] Allocating fbdev: Stolen memory not preferred.
<7> [45.161276] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] allocated 1024x768 fb
<6> [45.165183] fbcon: i915drmfb (fb0) is primary device
<7> [45.168522] i915 0000:00:02.0: [drm:compute_baseline_pipe_bpp [i915]] [CONNECTOR:92:VGA-1] Limiting target display pipe bpp to 24 (EDID bpp 0, max requested bpp 0, max platform bpp 36)
<7> [45.169165] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [45.169570] i915 0000:00:02.0: [drm:intel_fdi_atomic_check_link [i915]] checking fdi config on pipe A, lanes 1
<7> [45.169990] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in fdi_lanes (expected 2, found 1)
<7> [45.170393] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in fdi_m_n (expected tu 64 data 5033164/8388608 link 209715/524288, found tu 64, data 6039797/8388608 link 125829/524288)
<7> [45.170767] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1280, found 1024)
<7> [45.171222] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 1688, found 1344)
<7> [45.171603] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1280, found 1024)
<7> [45.171979] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 1688, found 1344)
<7> [45.172379] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 1328, found 1048)
<7> [45.172757] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 1440, found 1184)
<7> [45.173184] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1024, found 768)
<7> [45.173492] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1024, found 768)
<7> [45.173742] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1025, found 771)
<7> [45.174004] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1028, found 777)
<7> [45.174303] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1066, found 806)
<7> [45.174598] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1066, found 806)
<7> [45.174860] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1280, found 1024)
<7> [45.175156] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 1688, found 1344)
<7> [45.175494] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1280, found 1024)
<7> [45.175749] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 1688, found 1344)
<7> [45.176004] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 1328, found 1048)
<7> [45.176301] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 1440, found 1184)
<7> [45.176591] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1024, found 768)
<7> [45.176838] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1024, found 768)
<7> [45.177084] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1025, found 771)
<7> [45.177722] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1028, found 777)
<7> [45.177981] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1066, found 806)
<7> [45.178280] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1066, found 806)
<7> [45.178559] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 1, found 0)
<7> [45.178806] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [45.179053] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (4) (expected 4, found 0)
<7> [45.179379] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [45.179671] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in dpll_hw_state
<7> [45.179936] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] expected:
<7> [45.180197] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: dpll: 0xc4040004, dpll_md: 0x0, fp0: 0x10c09, fp1: 0x30d07
<7> [45.180489] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] found:
<7> [45.180768] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: dpll: 0xc4100010, dpll_md: 0x0, fp0: 0x10c09, fp1: 0x10c09
<7> [45.181014] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 108000, found 64800)
<7> [45.181300] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 108000, found 64800)
<7> [45.181600] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in port_clock (expected 108000, found 64800)
<7> [45.181866] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] fastset requirement not met, forcing full modeset
<7> [45.182127] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:53:pipe A] releasing PCH DPLL A
<7> [45.182484] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:53:pipe A] min cdclk: 120000 kHz -> 72000 kHz
<7> [45.182750] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:53:pipe A] allocated PCH DPLL A
<7> [45.183003] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:53:pipe A] reserving PCH DPLL A
<7> [45.183262] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: yes [modeset]
<7> [45.183560] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: ANALOG (0x2), output format: RGB, sink format: RGB
<7> [45.183826] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0
<7> [45.184077] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [45.184352] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [45.184621] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [45.184872] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [45.185123] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fdi: lanes: 1; data_m: 6039797, data_n: 8388608, link_m: 125829, link_n: 524288, tu: 64
<7> [45.185445] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [45.185714] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [45.185975] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [45.186220] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0
<7> [45.186525] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0
<7> [45.186783] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [45.187029] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [45.187275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [45.187566] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=64800, hd=1024 hb=1024-1344 hs=1048-1184 ht=1344, vd=768 vb=768-806 vs=771-777 vt=806, flags=0xa
<7> [45.187835] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1024x768": 60 64800 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [45.188081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=64800, hd=1024 hb=1024-1344 hs=1048-1184 ht=1344, vd=768 vb=768-806 vs=771-777 vt=806, flags=0xa
<7> [45.188328] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 64800, pixel rate 64800, min cdclk 72000, min voltage level 0
<7> [45.188703] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [45.189061] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 1024x768+0+0
<7> [45.189425] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [45.189776] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [45.190023] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [45.190269] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: dpll: 0xc4100010, dpll_md: 0x0, fp0: 0x10c09, fp1: 0x10c09
<7> [45.190566] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [45.190812] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [45.191057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [45.191302] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.191580] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.191826] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [45.192071] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [45.192315] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:primary A] fb: [FB:108] 1024x768 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [45.192604] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [45.192858] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1024.000000x768.000000+0.000000+0.000000 dst: 1024x768+0+0
<7> [45.193104] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:sprite A] fb: [NOFB], visible: no
<7> [45.193349] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [45.204559] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [45.222670] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [45.223200] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [45.223784] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [45.237815] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable PCH DPLL A (active 0x1, on? 1) for [CRTC:53:pipe A]
<7> [45.238537] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling PCH DPLL A
<7> [45.239335] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:93:CRT]
<7> [45.239873] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:HDMI B]
<7> [45.240445] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DP B]
<7> [45.241371] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [45.241798] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI_RX_IIR before link train 0x700
<7> [45.242083] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI_RX_IIR 0x700
<7> [45.242343] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI train 1 done, level 0.
<7> [45.242599] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI_RX_IIR 0x600
<7> [45.242868] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI train 2 done, level 0.
<7> [45.243139] i915 0000:00:02.0: [drm:ivb_manual_fdi_link_train [i915]] FDI train done.
<7> [45.243560] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable PCH DPLL A (active 0x1, on? 0) for [CRTC:53:pipe A]
<7> [45.243808] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling PCH DPLL A
<7> [45.312610] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:92:VGA-1]
<7> [45.313270] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:53:pipe A]
<6> [45.315899] Console: switching to colour frame buffer device 128x48
<6> [45.330847] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [45.331074] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [45.330893] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display version: 7
<7> [45.331551] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [45.331535] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display stepping: N/A
<7> [45.332059] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: cursor_needs_physical: no
<7> [45.332609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:92:VGA-1]
<7> [45.332636] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:92:VGA-1] force=1
<7> [45.333420] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_crawl: no
<7> [45.334370] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_squash: no
<7> [45.334545] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [45.334721] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ddi: no
<7> [45.334793] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [45.335069] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dp_mst: no
<7> [45.335339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [45.335438] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsb: no
<7> [45.335606] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [45.335952] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_fpga_dbg: no
<7> [45.336349] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_gmch: no
<7> [45.336705] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hotplug: yes
<7> [45.336777] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [45.337024] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [45.336992] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hti: no
<7> [45.337029] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.337243] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ipc: no
<7> [45.337290] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [45.337516] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_overlay: no
<7> [45.337769] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr: no
<7> [45.338019] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr_hw_tracking: no
<7> [45.338270] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: overlay_needs_physical: no
<7> [45.338659] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [45.338547] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: supports_tv: no
<7> [45.338664] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [45.338799] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hdcp: no
<7> [45.339077] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:92:VGA-1] probed modes:
<7> [45.339089] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [45.339093] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [45.339098] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [45.339102] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [45.339105] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [45.339110] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [45.339051] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dmc: no
<7> [45.339115] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [45.339303] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsc: no
<7> [45.339584] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: rawclk rate: 125000 kHz
<7> [45.339791] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.340037] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [45.340394] [drm:intel_dsm_detect.isra.0 [i915]] no _DSM method for intel device
<7> [45.340436] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [45.340682] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.340668] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: pciid=0x0162 rev=0x09 platform=IVYBRIDGE (subplatform=0x0) gen=7
<7> [45.340686] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.340901] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics version: 7
<7> [45.340921] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [45.341147] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media version: 7
<7> [45.341445] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics stepping: **
<7> [45.341686] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media stepping: **
<7> [45.341929] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gt: 2
<7> [45.342264] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [45.342173] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: memory-regions: 0x21
<7> [45.342269] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [45.342558] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [45.342565] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [45.342453] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: page-sizes: 0x1000
<7> [45.342570] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [45.342708] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: platform: IVYBRIDGE
<7> [45.342951] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-size: 31
<7> [45.343196] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-type: 1
<7> [45.343469] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: dma_mask_size: 40
<7> [45.343718] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_mobile: no
<7> [45.343962] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: require_force_probe: no
<7> [45.344205] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_dgfx: no
<7> [45.344458] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64bit_reloc: no
<7> [45.344735] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64k_pages: no
<7> [45.344977] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gpu_reset_clobbers_display: no
<7> [45.345221] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_reset_engine: yes
<7> [45.345476] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_3d_pipeline: yes
<7> [45.345742] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_flat_ccs: no
<7> [45.345984] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_global_mocs: no
<7> [45.346227] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gmd_id: no
<7> [45.346471] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gt_uc: no
<7> [45.346768] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_pxp: no
<7> [45.346994] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [45.347001] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:92:VGA-1] enabled? yes
<7> [45.347005] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:95:HDMI-A-1] enabled? no
<7> [45.347009] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:103:DP-1] enabled? no
<7> [45.347111] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [45.347008] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_gscfi: no
<7> [45.347133] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:92:VGA-1] found first mode: 1024x768
<7> [45.347137] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<7> [45.347173] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:53:pipe A] desired mode 1024x768 set (0,0)
<7> [45.347252] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_deprivilege: no
<7> [45.347496] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_tlb_invalidation: no
<7> [45.347908] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_ccs_read: no
<7> [45.348139] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_dpf: yes
<7> [45.348383] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_llc: yes
<7> [45.348663] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_contexts: no
<7> [45.348904] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_elsq: no
<7> [45.349158] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_media_ratio_mode: no
<7> [45.349408] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_mslice_steering: no
<7> [45.349726] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_bpc_reporting: no
<7> [45.350068] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_slice_contrib_limits: no
<7> [45.350307] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oam: no
<7> [45.350558] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_one_eu_per_fuse_bit: no
<7> [45.350825] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pxp: no
<7> [45.351063] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6: yes
<7> [45.351316] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6p: yes
<7> [45.351567] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rps: yes
<7> [45.351832] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_runtime_pm: no
<7> [45.352071] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_snoop: no
<7> [45.352331] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_coherent_ggtt: yes
<7> [45.352592] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: tuning_thread_rr_after_dep: no
<7> [45.352855] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: unfenced_needs_alignment: no
<7> [45.353103] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: hws_needs_physical: no
<7> [45.353347] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pooled_eu: no
<7> [45.353591] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: iommu: enabled
<7> [45.353851] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: available engines: 403
<7> [45.354100] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice total: 0, mask=0000
<7> [45.354344] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: subslice total: 0
<7> [45.354588] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU total: 0
<7> [45.354869] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU per subslice: 0
<7> [45.355109] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has slice power gating: no
<7> [45.355353] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has subslice power gating: no
<7> [45.355611] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has EU power gating: no
<6> [45.355870] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [45.355871] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [45.355872] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [45.385287] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [45.397553] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [45.398317] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [45.413720] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [45.413881] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [45.446278] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [45.446648] [IGT] i915_module_load: finished subtest load, SUCCESS
<6> [45.447031] [IGT] i915_module_load: exiting, ret=0
Created at 2026-05-04 11:06:35