Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.32 seconds
Igt-Version 
IGT-Version: 2.4-g574c502c4 (x86_64) (Linux: 7.0.0-rc6-CI_DRM_18273-g76f07a8a9c76+ x86_64)
Out 
Using IGT_SRANDOM=1775164220 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888117d39828 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.315s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.315s)
Dmesg
<6> [139.701888] Console: switching to colour dummy device 80x25
<6> [139.701993] [IGT] kms_pm_rpm: executing
<7> [139.705365] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [139.711619] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [139.711630] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [139.711944] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.713197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [139.713933] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.714694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [139.715386] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [139.715842] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [139.716857] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.718420] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.719931] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.721486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.723150] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.724824] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.726507] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.728189] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.729749] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.730707] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [139.731602] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [139.732060] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [139.732712] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [139.733554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [139.733563] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [139.738101] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [139.738911] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [139.738921] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [139.804733] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [139.807983] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [139.807993] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [139.808332] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [139.811767] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [139.811776] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [139.812154] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [139.812897] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [139.812909] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [139.813891] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [139.814492] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [139.815653] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.816165] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [139.816575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [139.816928] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.817445] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.818344] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [139.818714] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.819657] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [139.820569] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.821449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [139.822866] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.824399] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.826158] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.827924] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.829570] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.831195] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.832915] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.834434] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.835446] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [139.836163] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [139.836604] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [139.837179] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [139.837230] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [139.837240] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [139.841725] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [139.841752] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [139.841759] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [139.907708] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [139.910961] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [139.910972] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [139.911385] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [139.914671] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [139.914682] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [139.915193] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [139.915280] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [139.915295] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [139.916170] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [139.916734] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [139.917819] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.919443] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.920209] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [139.920959] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [139.921731] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.922425] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.924679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [139.925521] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.926329] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [139.928711] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.930358] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.932184] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.934067] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.935784] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.937492] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.939121] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [139.940118] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [139.941143] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [139.941678] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [139.942450] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [139.942627] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [139.942643] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [139.947332] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [139.947426] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [139.947434] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [140.013125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [140.016952] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [140.016974] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.017597] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [140.021467] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [140.021484] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [140.022168] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [140.032267] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.032986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [140.033676] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.034618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.035817] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.031899] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.040565] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [141.064086] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [141.073823] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [141.075161] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.075566] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [141.076270] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [141.076804] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [141.077662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.078731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [141.079829] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [141.080278] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [141.081216] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.082843] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.084372] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.085996] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.087701] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.089318] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.091740] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.093356] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.094973] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.095901] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [141.097052] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [141.097799] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [141.099098] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [141.103601] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [141.169628] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [141.173066] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.173079] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [141.173465] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [141.176845] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.176856] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [141.178328] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [141.178657] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [141.200100] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [141.200815] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [141.201459] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [141.202283] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [141.203545] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.205095] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.216072] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [141.283604] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [141.335258] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [141.347063] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [141.353798] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [141.354548] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.354832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [141.355837] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.356844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [141.357179] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [141.357312] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [141.358189] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [141.358616] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [141.359499] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.360973] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.362598] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.364063] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.365729] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.367373] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.369048] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.370665] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.372143] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.373097] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [141.374058] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [141.374725] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [141.375888] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [141.380375] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [141.446007] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [141.449429] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.449442] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [141.450072] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [141.453666] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.453680] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [141.455101] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [141.480273] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [141.481328] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [141.482128] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [141.483017] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [141.484262] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.485997] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.495975] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [141.569250] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [141.588430] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [141.590683] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.592112] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [141.592184] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [141.594177] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.598092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [141.599979] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [141.601153] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [141.603346] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [141.605639] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.608219] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.610438] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.612342] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.616259] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.618225] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.620140] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.622874] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.624692] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [141.625703] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [141.626951] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [141.627798] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [141.629230] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [141.633852] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [141.699577] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [141.702915] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.702926] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [141.703275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [141.705040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [141.705768] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [141.706423] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [141.707030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [141.708709] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [141.708724] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [141.709221] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.709797] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.710439] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [141.711399] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.712478] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [141.712913] [IGT] kms_pm_rpm: exiting, ret=0
<6> [141.716151] Console: switching to colour frame buffer device 128x48
Created at 2026-04-03 20:42:10