Results for igt@kms_frontbuffer_tracking@fbc-1p-primscrn-cur-indfb-draw-blt

Result: Pass

integration-manifest git-log-oneline i915_display_info15 igt_runner15 runtimes15 results15.json results15-i915-load.json guc_logs15.tar i915_display_info_post_exec15 boot15 dmesg15

DetailValue
Duration 2.74 seconds
Hostname 
shard-dg1-14
Igt-Version 
IGT-Version: 2.3-g33f5420a2 (x86_64) (Linux: 7.0.0-rc4-CI_DRM_18152-gbd57a29321bf+ x86_64)
Out 
Using IGT_SRANDOM=1773634397 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test PSR: no usable eDP screen.
Can't test DRRS: no usable screen.
Starting subtest: fbc-1p-primscrn-cur-indfb-draw-blt
Subtest fbc-1p-primscrn-cur-indfb-draw-blt: SUCCESS (2.742s)
Err 
Starting subtest: fbc-1p-primscrn-cur-indfb-draw-blt
Subtest fbc-1p-primscrn-cur-indfb-draw-blt: SUCCESS (2.742s)
Dmesg
<6> [477.546294] Console: switching to colour dummy device 80x25
<6> [477.546804] [IGT] kms_frontbuffer_tracking: executing
<7> [477.551862] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [477.553027] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [477.553301] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [477.566625] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [477.566633] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [477.566895] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [477.567052] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [477.567391] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [477.588428] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.609559] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.630680] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.651794] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.672905] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.694021] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.715158] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.736295] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.757432] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.778588] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.799731] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.820871] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.842006] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.863145] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.884286] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.905423] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.926611] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.947753] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.968892] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [477.990028] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.011164] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.032299] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.053435] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.074589] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.095730] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.116876] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.138012] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.159148] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.180284] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.201419] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.222590] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.243734] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.243903] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [478.243947] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [478.244726] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [478.244732] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [478.248968] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [478.249432] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [478.249437] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [478.253635] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [478.254177] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [478.254182] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [478.258412] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [478.258946] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [478.258951] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [478.263150] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [478.263609] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [478.263613] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [478.267926] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [478.268617] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1]
<7> [478.268622] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:587:DP-1]
<7> [478.289843] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.310943] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.332067] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.353191] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.374315] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.395438] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.416571] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.437714] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.458838] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.479977] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.501128] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.522272] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.543408] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.564530] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.585699] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.606835] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.627971] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.649108] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.670244] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.691385] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.712520] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.733674] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.754820] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.775957] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.797091] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.818227] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.839362] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.860499] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.881673] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.902814] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.923953] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.945089] i915 0000:03:00.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [478.945255] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<7> [478.945299] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:587:DP-1] disconnected
<7> [478.945319] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1]
<7> [478.945323] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:599:HDMI-A-1]
<7> [478.970334] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD monitor FH-DP4K
<7> [478.970340] i915 0000:03:00.0: [drm:update_display_info.part.0] [CONNECTOR:599:HDMI-A-1] ELD size 36, SAD count 2
<7> [478.970543] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [478.970702] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK on first message, retry
<7> [478.971045] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpa] NAK for addr: 0040 w(1)
<7> [478.971202] i915 0000:03:00.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [478.971215] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] Assuming DP dual mode adaptor presence based on VBT
<7> [478.971349] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] DP dual mode adaptor (type 1 DVI) detected (max TMDS clock: 165000 kHz)
<7> [478.972148] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1440": 60 241700 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9 (CLOCK_HIGH)
<7> [478.972157] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "2560x1600": 60 267820 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9 (CLOCK_HIGH)
<7> [478.972164] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 297000 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [478.972171] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "3840x2160": 30 266640 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9 (CLOCK_HIGH)
<7> [478.972178] i915 0000:03:00.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 120 296703 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 (CLOCK_HIGH)
<7> [478.972186] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:599:HDMI-A-1] probed modes:
<7> [478.972190] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
<7> [478.972193] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 17 151100 3840 3888 3920 4000 2160 2163 2168 2222 0x40 0x9
<7> [478.972197] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1600": 30 133910 2560 2608 2640 2720 1600 1603 1608 1641 0x40 0x9
<7> [478.972200] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2560x1440": 30 120850 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9
<7> [478.972204] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x40 0x9
<7> [478.972208] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148352 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [478.972211] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [478.972215] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [478.972218] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [478.972222] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [478.972226] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [478.972229] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [478.972233] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1152x864": 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
<7> [478.972236] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [478.972240] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [478.972243] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
<7> [478.972247] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
<7> [478.972250] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [478.972254] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
<7> [478.972257] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
<7> [478.972261] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [478.972264] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [478.972268] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
<7> [478.972271] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
<7> [478.972275] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
<7> [478.972278] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [478.972309] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2]
<7> [478.972314] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:606:HDMI-A-2]
<7> [478.976534] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:606:HDMI-A-2] disconnected
<7> [478.976551] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2]
<7> [478.976555] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:610:DP-2]
<7> [478.980777] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:610:DP-2] disconnected
<7> [478.980794] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3]
<7> [478.980798] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:618:HDMI-A-3]
<7> [478.984980] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:618:HDMI-A-3] disconnected
<7> [478.984996] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3]
<7> [478.985000] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:622:DP-3]
<7> [478.989190] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:622:DP-3] disconnected
<7> [478.989206] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4]
<7> [478.989209] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:630:HDMI-A-4]
<7> [478.993398] i915 0000:03:00.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:630:HDMI-A-4] disconnected
<7> [478.995474] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [478.995570] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [478.995683] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [478.995856] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [478.995989] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<6> [478.998661] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-cur-indfb-draw-blt
<7> [478.999530] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:637]
<7> [478.999621] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:638]
<7> [478.999822] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:639]
<7> [478.999953] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:640]
<7> [479.000069] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:641]
<7> [479.000681] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [479.052863] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [479.107028] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<7> [479.123909] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [479.123994] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [479.142966] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.143464] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.143941] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.144434] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.144908] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.172755] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [479.212879] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [479.234247] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [479.292637] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.293077] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.324847] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.325404] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.325951] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.359120] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.360013] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.376852] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:642] from all active usage due to RMFB ioctl
<7> [479.377126] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:642] is removed
<7> [479.377330] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [479.378190] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [479.379017] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [479.379849] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [479.380651] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [479.381573] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [479.382493] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [479.391948] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:633]
<7> [479.392585] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:642]
<7> [479.393259] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:645]
<7> [479.393901] i915 0000:03:00.0: [drm:drm_mode_addfb2] [FB:646]
<7> [479.407939] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.408863] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.409727] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.579129] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.579334] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.657468] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [479.657552] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [479.657766] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [479.658106] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [479.658425] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [479.658764] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [479.659132] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [479.659557] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [479.659961] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [479.660341] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [479.674839] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.675047] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.675215] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.675409] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.675581] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.682609] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [479.690913] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [479.698962] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [479.764552] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.765915] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.791929] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.792847] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.793678] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.825823] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.826674] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.841063] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [479.841270] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [479.858034] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.858309] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.858970] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.859826] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.862440] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.863308] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.892957] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.893880] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.894760] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.925669] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.926570] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.941070] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [479.941278] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [479.958293] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [479.959422] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.960357] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.961215] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [479.963988] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [479.964862] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [479.991964] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [479.992905] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [479.993802] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.025768] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.026615] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.041077] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [480.041288] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [480.058320] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.059447] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.060382] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.061243] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.063994] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.064870] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.091962] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.092893] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.093800] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.125839] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.126687] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.143799] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:646] from all active usage due to RMFB ioctl
<7> [480.144080] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:646] is removed
<7> [480.144284] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [480.145135] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [480.145963] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [480.146798] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [480.147599] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [480.148514] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [480.149421] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [480.160105] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [480.175960] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.176897] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.177766] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.214116] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.214327] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.290932] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:170:pipe A]
<7> [480.291033] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CONNECTOR:599:HDMI-A-1]
<7> [480.291246] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [480.291641] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [480.292046] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [480.292426] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [480.292819] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [480.293245] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [480.293629] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [480.294067] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [480.296922] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [480.297410] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [480.335593] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:308:pipe B]
<7> [480.349486] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:446:pipe C]
<7> [480.356503] i915 0000:03:00.0: [drm:drm_mode_setcrtc] [CRTC:584:pipe D]
<7> [480.409836] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.410254] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [480.426954] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.427393] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.427930] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.463805] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.466696] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.467575] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.547950] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.549060] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.550007] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.550941] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.553549] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.554432] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.574944] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.575863] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.576695] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.609109] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.609994] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.625158] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [480.638816] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [480.639635] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [480.640488] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 6, 11, 11, 11, 17, 17, 19, 21, 20, 0, 0
<7> [480.641398] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 14, 14, 14, 20, 20, 22, 25, 21, 0, 0
<7> [480.642375] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.643311] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.644172] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.645343] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.646466] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.649010] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [480.666944] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.667872] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.668707] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.696598] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.699524] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.700394] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.781243] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.807941] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.808859] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.809691] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.842426] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.843336] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.858482] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [480.872293] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [480.874984] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [480.876032] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [480.876900] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [480.918588] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [480.921461] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [480.922352] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [480.997828] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.014074] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.014986] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.015848] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.059093] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.059989] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.075156] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [481.089557] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [481.091950] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.092899] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.093762] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.135566] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.138486] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.139362] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.229070] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.230008] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.230945] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.231285] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.234179] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.235468] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.257942] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.258857] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.259684] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.292418] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.293307] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.308474] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [481.321327] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [481.325948] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.326859] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.327692] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.367596] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.370490] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.371402] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.447862] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.462095] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.463014] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.463881] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.509112] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.510002] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.525168] [drm:eb_validate_vma [i915]] EINVAL at eb_validate_vma:509
<7> [481.537977] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [481.542962] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.543878] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.544705] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.583616] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.586498] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.587371] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.664578] i915 0000:03:00.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [481.678096] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.679009] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.679875] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.725708] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.726615] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<6> [481.743315] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-cur-indfb-draw-blt, SUCCESS
<7> [481.745647] i915 0000:03:00.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:637] from all active usage due to RMFB ioctl
<7> [481.745953] i915 0000:03:00.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:637] is removed
<7> [481.746162] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 2012) -> ( 0 - 0), size 2012 -> 0
<7> [481.747000] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [481.747820] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.748618] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.749555] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.750463] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 0 num active planes 0
<7> [481.751304] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 0
<7> [481.752127] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [481.757097] i915 0000:03:00.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:34:plane 1A]
<6> [481.777712] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [481.780092] i915 0000:03:00.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [481.792927] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [481.793111] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [481.793265] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [481.811946] i915 0000:03:00.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2012), size 0 -> 2012
<7> [481.812131] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [481.812304] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0
<7> [481.812478] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 81, 81, 81, 129, 129, 145, 161, 30, 0, 0
<7> [481.812650] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 91, 91, 91, 143, 143, 161, 179, 31, 0, 0
<7> [481.812834] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [481.813006] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] lines 3, 5, 5, 5, 8, 8, 9, 10, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.813179] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] blocks 6, 11, 11, 11, 17, 17, 19, 21, 20, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.813351] i915 0000:03:00.0: [drm:skl_print_plane_changes [i915]] [PLANE:164:cursor A] min_ddb 8, 14, 14, 14, 20, 20, 22, 25, 21, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [481.813552] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] [CRTC:170:pipe A] data rate 594000 num active planes 1
<7> [481.813729] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 34000 required 594
<7> [481.813916] i915 0000:03:00.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1
<7> [481.814657] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.814872] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [481.815280] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1
<7> [481.815474] i915 0000:03:00.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:34:plane 1A]
<7> [481.823886] i915 0000:03:00.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [481.840656] Console: switching to colour frame buffer device 240x67
Created at 2026-03-16 05:31:13