Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.3-ga7e8b577d (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18148-gb5b4e8494ce1+ x86_64)
Out	Using IGT_SRANDOM=1773455668 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810c741820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.415s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810c741820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.415s)
Dmesg	<6> [65.326021] Console: switching to colour dummy device 80x25 <6> [65.326073] [IGT] kms_pm_rpm: executing <6> [65.328095] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [65.328317] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [65.332360] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [65.332366] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [65.336566] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [65.336812] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [65.336816] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [65.341005] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [65.341255] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [65.341259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [65.345471] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [65.345737] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [65.345740] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [65.349920] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [65.349931] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [65.349934] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [65.354119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [65.354131] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [65.354133] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [65.358348] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [65.358365] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [65.358367] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [65.360281] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [65.360460] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [65.360599] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [65.363188] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [65.363232] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [65.363235] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [65.368044] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [65.368074] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [65.368076] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [65.372923] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [65.480529] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.375789] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [66.383074] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.384504] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.384737] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.385020] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.385159] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.387297] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [66.411502] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [66.419331] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.420164] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.421100] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.422081] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.423007] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.423845] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.424838] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.425038] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.425279] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.425450] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.425704] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.426396] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.426536] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.432675] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [66.433896] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.434056] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [66.435199] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [66.438864] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [66.443763] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [66.448610] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.448750] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.448894] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.449729] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.451139] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [66.451227] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [66.469590] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.469882] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.470225] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.471751] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.472106] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [66.475494] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.476799] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.477028] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.477305] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.477452] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.479482] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [66.552313] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [66.564685] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [66.572348] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.573243] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.574182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.575196] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.576147] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.577096] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.577794] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.577973] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.578351] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.578507] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.578848] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.579551] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.579688] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.585829] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [66.585943] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.586081] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.587065] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.588478] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [66.588719] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [66.592680] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [66.596971] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [66.597150] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [66.614658] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.614807] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.614942] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.616220] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.616615] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [66.621137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.622539] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.623146] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.623832] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.624314] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.629518] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [66.709801] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [66.717626] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.718458] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.719386] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.720431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.721413] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.722386] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.723338] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.724269] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.725940] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.726793] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.727785] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.730297] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.731112] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.741505] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [66.742015] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [66.742368] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [66.744689] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [66.744864] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [66.747203] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [66.752153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [66.753192] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.754654] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [66.754824] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [66.759005] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [66.850008] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.850922] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.851743] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.853700] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [66.854531] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [66.860662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [66.862383] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [66.863333] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [66.864333] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [66.865092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [66.871841] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [66.978386] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [66.985975] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [66.986302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [66.987249] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [66.988325] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.989285] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.990267] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.991201] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [66.992150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [66.993062] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [66.993197] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [66.993678] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [66.994393] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.994535] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.005546] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [67.005722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.006002] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [67.006758] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.008184] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [67.008288] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [67.008527] [IGT] kms_pm_rpm: exiting, ret=0 <7> [67.012532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <6> [67.017159] Console: switching to colour frame buffer device 160x45 <7> [67.017977] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]

Created at 2026-03-14 02:53:20