Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.31 seconds
Igt-Version 
IGT-Version: 2.3-g611f1cac6 (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18142-g4082c266f293+ x86_64)
Out 
Using IGT_SRANDOM=1773391552 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888126a55820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.312s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.312s)
Dmesg
<6> [123.966399] Console: switching to colour dummy device 80x25
<6> [123.966502] [IGT] kms_pm_rpm: executing
<7> [123.969954] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [123.976295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [123.976306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [123.976584] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.977288] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.977971] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.978638] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.979302] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.979672] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.980634] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.982197] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.983711] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.985256] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.986878] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.988559] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.990243] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.991861] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.993451] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.994348] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.995007] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.995377] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.995931] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [123.996583] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [123.996591] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [124.000975] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [124.001516] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [124.001523] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [124.069510] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [124.073383] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.073396] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [124.073781] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [124.077159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.077171] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [124.077584] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [124.078598] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [124.078612] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [124.079584] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [124.080249] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [124.081305] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.082022] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [124.082587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.083095] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.083573] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.084560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.085695] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.086631] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.087529] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.088366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [124.089840] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.091604] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.093417] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.095499] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.097429] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.099335] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.101180] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.103103] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.104305] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [124.105319] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [124.105894] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [124.106672] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [124.106728] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [124.106739] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [124.111360] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [124.111405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [124.111415] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [124.179911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [124.183510] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.183522] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [124.183897] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [124.187097] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.187108] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [124.187465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [124.187529] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [124.187538] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [124.188334] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [124.188731] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [124.189854] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.191517] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.193363] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.195024] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.196781] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.198605] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.200428] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.202243] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.203986] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.205103] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [124.206208] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [124.206768] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [124.207664] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [124.207857] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [124.207871] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [124.212571] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [124.212684] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [124.212694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [124.281503] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [124.285291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.285305] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [124.285708] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [124.289103] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.289116] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [124.289549] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [124.297987] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [124.298510] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.298994] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.299516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.300539] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.297590] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.304267] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.329931] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.339685] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.340999] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.341361] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [125.342563] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.343250] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.344005] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [125.343846] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.344799] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.345127] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.345938] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.347482] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.349012] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.350592] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.352239] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.353840] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.355486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.357178] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.358824] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.359842] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.361140] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.361842] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.363719] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [125.368240] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [125.436468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.440379] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.440393] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.440811] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.444427] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.444440] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.445311] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [125.445644] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [125.465063] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.465728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.466309] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.466981] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.468675] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.470354] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.478570] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [125.551119] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [125.604030] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [125.615893] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.622673] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.623417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.623656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.624588] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.625592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [125.626005] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.626302] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [125.626788] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.627115] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.627946] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.629445] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.630950] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.632415] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.634000] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.635716] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.637377] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.638961] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.640532] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.641476] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.642519] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.643247] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.644938] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [125.649387] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [125.717471] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.721087] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.721098] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.721398] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.724546] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.724556] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.725409] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [125.744928] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.745587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.746131] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.746605] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.747520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.748045] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.754853] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.839128] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.858339] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.859321] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.860226] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [125.860209] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.861648] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [125.864887] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [125.864568] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.867334] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.868607] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.870964] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.873407] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.876225] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.878568] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.880574] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.882565] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.884508] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.886338] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.888090] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.889155] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.890445] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.891356] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.893061] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [125.897566] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [125.965431] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.968879] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.969307] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.969679] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.970066] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.970927] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.970940] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.971308] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.990656] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.990664] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.990994] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.991392] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.991680] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.992364] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.993090] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [125.993219] [IGT] kms_pm_rpm: exiting, ret=0
<6> [125.995663] Console: switching to colour frame buffer device 128x48
Created at 2026-03-14 07:22:32