Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.51 seconds
Igt-Version 
IGT-Version: 2.3-gd92116c0c (x86_64) (Linux: 7.0.0-rc3-CI_DRM_18135-ga0e231ebb0df+ x86_64)
Out 
Using IGT_SRANDOM=1773312698 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888127a91820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.511s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 2
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888127a91820 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b7c/0x26e0
     do_syscall_64+0xdd/0x1470

ref_tracker: intel_runtime_pm@ffff888127a91820 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get+0x1a/0x30 [i915]
     intel_display_rpm_get+0x1f/0x30 [i915]
     intel_display_power_get+0x22/0x70 [i915]
     i915_hpd_poll_init_work+0x1b2/0x2e0 [i915]
     process_one_work+0x22e/0x740
     worker_thread+0x1e8/0x3d0
     kthread+0x10d/0x150
     ret_from_fork+0x3d4/0x480
     ret_from_fork_asm+0x1a/0x30
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.511s)
Dmesg
<6> [89.102436] Console: switching to colour dummy device 80x25
<6> [89.102503] [IGT] kms_pm_rpm: executing
<7> [89.107824] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.108201] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.108412] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.108666] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.109342] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [89.153499] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [89.153838] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [89.157572] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [89.157592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [89.157788] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.162204] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [89.162511] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [89.162523] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [89.163165] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.163680] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.164220] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.164863] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.165349] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.165966] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [89.166276] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [89.166281] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [89.166769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.166965] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.167347] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.167598] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.167617] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.167796] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.172001] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.172006] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.172186] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [89.172405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [89.172409] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [89.176743] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [89.176759] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [89.176763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [89.177471] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.177993] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.178575] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [89.178591] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [89.178607] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [89.179024] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.179192] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.179615] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.179831] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.179835] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.179999] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.184212] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.184216] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.184395] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [89.184416] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [89.184420] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [89.188726] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [89.188765] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [89.188768] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [89.189479] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.189964] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.190554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [89.190605] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [89.190609] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [89.191022] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.191190] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.191614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.191814] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.191817] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.191982] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.196159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.196164] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.196344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [89.267784] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.268296] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.268796] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.269341] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.270477] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.253037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.259773] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.284781] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.291789] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.292955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.293937] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [100.293364] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [100.298523] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [100.299925] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.300651] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.301397] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.303146] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.304062] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.305545] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [100.306139] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.306330] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.306714] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.306934] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.306939] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.307120] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.311253] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.311257] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.311665] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [100.311796] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [100.411508] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.412480] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.413492] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.414490] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.415912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.416682] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.423404] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.513559] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [100.525506] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.534898] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.535124] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.535675] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.536181] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.536838] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [100.537071] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [100.541143] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [100.541487] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.542459] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.543233] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.544589] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [100.544823] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [100.545270] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.545467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.545869] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.546076] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.546080] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.546247] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.550456] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.550460] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.554453] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.554687] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.554876] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.555061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.555728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.556048] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.559345] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.657212] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.662352] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.662543] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.662753] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.663268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.664032] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<6> [100.664737] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [100.665026] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [100.668360] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [100.668699] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.669743] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.670570] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.671931] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [100.672045] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [100.673803] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [100.674246] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.674493] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.674872] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.675078] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.675081] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.675247] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.679729] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.679734] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.771493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.771840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.772132] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.772446] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.773323] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.773773] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.778215] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.887414] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.893829] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.894237] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.894590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.895328] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.896037] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [100.896151] [IGT] kms_pm_rpm: exiting, ret=0
<7> [100.896036] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [100.900547] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [100.900985] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.902068] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.902841] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.904082] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [100.904574] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.904772] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.905143] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.905400] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.905405] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.905584] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.909957] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.909960] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<6> [100.910458] Console: switching to colour frame buffer device 128x48
<7> [100.914441] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.914669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.914859] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.915071] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.915746] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-03-13 08:30:37